mbed library sources modified for open wear
Dependents: openwear-lifelogger-example
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_STM32F3XX/system_stm32f30x.c
- Revision:
- 155:8435094ec241
diff -r be4113396fa5 -r 8435094ec241 targets/cmsis/TARGET_STM/TARGET_STM32F3XX/system_stm32f30x.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_STM32F3XX/system_stm32f30x.c Tue Apr 08 09:15:06 2014 +0100 @@ -0,0 +1,478 @@ +/** + ****************************************************************************** + * @file system_stm32f30x.c + * @author MCD Application Team + * @version V1.0.0 + * @date 05-March-2014 + * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File. + * This file contains the system clock configuration for STM32F30x devices, + * and is generated by the clock configuration tool + * stm32f30x_Clock_Configuration_V1.0.0.xls + * + * 1. This file provides two functions and one global variable to be called from + * user application: + * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier + * and Divider factors, AHB/APBx prescalers and Flash settings), + * depending on the configuration made in the clock xls tool. + * This function is called at startup just after reset and + * before branch to main program. This call is made inside + * the "startup_stm32f30x.s" file. + * + * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used + * by the user application to setup the SysTick + * timer or configure other parameters. + * + * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must + * be called whenever the core clock is changed + * during program execution. + * + * 2. After each device reset the HSI (8 MHz) is used as system clock source. + * Then SystemInit() function is called, in "startup_stm32f30x.s" file, to + * configure the system clock before to branch to main program. + * + * 3. If the system clock source selected by user fails to startup, the SystemInit() + * function will do nothing and HSI still used as system clock source. User can + * add some code to deal with this issue inside the SetSysClock() function. + * + * 4. The default value of HSE crystal is set to 8MHz, refer to "HSE_VALUE" define + * in "stm32f30x.h" file. When HSE is used as system clock source, directly or + * through PLL, and you are using different crystal you have to adapt the HSE + * value to your own configuration. + * + * 5. This file configures the system clock as follows: + *----------------------------------------------------------------------------- + * System clock source | 1- PLL_HSE_EXTC | 3- PLL_HSI + * | (external 8 MHz clock) | (internal 8 MHz) + * | 2- PLL_HSE_XTAL | + * | (external 8 MHz xtal) | + *----------------------------------------------------------------------------- + * SYSCLK(MHz) | 72 | 64 + *----------------------------------------------------------------------------- + * AHBCLK (MHz) | 72 | 64 + *----------------------------------------------------------------------------- + * APB1CLK (MHz) | 36 | 32 + *----------------------------------------------------------------------------- + * APB2CLK (MHz) | 72 | 64 + *----------------------------------------------------------------------------- + * USB capable (48 MHz precise clock) | YES | NO + *----------------------------------------------------------------------------- + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/** @addtogroup CMSIS + * @{ + */ + +/** @addtogroup stm32f30x_system + * @{ + */ + +/** @addtogroup STM32F30x_System_Private_Includes + * @{ + */ + +#include "stm32f30x.h" + +/** + * @} + */ + +/** @addtogroup STM32F30x_System_Private_TypesDefinitions + * @{ + */ + +/** + * @} + */ + +/** @addtogroup STM32F30x_System_Private_Defines + * @{ + */ + +/*!< Uncomment the following line if you need to relocate your vector Table in + Internal SRAM. */ +/* #define VECT_TAB_SRAM */ +#define VECT_TAB_OFFSET 0x0 /*!< Vector Table base offset field. + This value must be a multiple of 0x200. */ +/** + * @} + */ + +/** @addtogroup STM32F30x_System_Private_Macros + * @{ + */ + +/* Select the clock sources (other than HSI) to start with (0=OFF, 1=ON) */ +#define USE_PLL_HSE_EXTC (1) /* Use external clock */ +#define USE_PLL_HSE_XTAL (1) /* Use external xtal */ + +/** + * @} + */ + +/** @addtogroup STM32F30x_System_Private_Variables + * @{ + */ + +uint32_t SystemCoreClock = 64000000; /* Default with HSI. Will be updated if HSE is used */ + +__I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; + +/** + * @} + */ + +/** @addtogroup STM32F30x_System_Private_FunctionPrototypes + * @{ + */ + +void SetSysClock(void); + +#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0) +uint8_t SetSysClock_PLL_HSE(uint8_t bypass); +#endif + +uint8_t SetSysClock_PLL_HSI(void); + +/** + * @} + */ + +/** @addtogroup STM32F30x_System_Private_Functions + * @{ + */ + +/** + * @brief Setup the microcontroller system + * Initialize the Embedded Flash Interface, the PLL and update the + * SystemFrequency variable. + * @param None + * @retval None + */ +void SystemInit(void) +{ + /* FPU settings ------------------------------------------------------------*/ + #if (__FPU_PRESENT == 1) && (__FPU_USED == 1) + SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */ + #endif + + /* Reset the RCC clock configuration to the default reset state ------------*/ + /* Set HSION bit */ + RCC->CR |= (uint32_t)0x00000001; + + /* Reset CFGR register */ + RCC->CFGR &= 0xF87FC00C; + + /* Reset HSEON, CSSON and PLLON bits */ + RCC->CR &= (uint32_t)0xFEF6FFFF; + + /* Reset HSEBYP bit */ + RCC->CR &= (uint32_t)0xFFFBFFFF; + + /* Reset PLLSRC, PLLXTPRE, PLLMUL and USBPRE bits */ + RCC->CFGR &= (uint32_t)0xFF80FFFF; + + /* Reset PREDIV1[3:0] bits */ + RCC->CFGR2 &= (uint32_t)0xFFFFFFF0; + + /* Reset USARTSW[1:0], I2CSW and TIMs bits */ + RCC->CFGR3 &= (uint32_t)0xFF00FCCC; + + /* Disable all interrupts */ + RCC->CIR = 0x00000000; + + /* Configure the System clock source, PLL Multiplier and Divider factors, + AHB/APBx prescalers and Flash settings */ + SetSysClock(); + + /* Configure the Vector Table location add offset address ------------------*/ +#ifdef VECT_TAB_SRAM + SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */ +#else + SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */ +#endif +} + +/** + * @brief Update SystemCoreClock variable according to Clock Register Values. + * The SystemCoreClock variable contains the core clock (HCLK), it can + * be used by the user application to setup the SysTick timer or configure + * other parameters. + * + * @note Each time the core clock (HCLK) changes, this function must be called + * to update SystemCoreClock variable value. Otherwise, any configuration + * based on this variable will be incorrect. + * + * @note - The system frequency computed by this function is not the real + * frequency in the chip. It is calculated based on the predefined + * constant and the selected clock source: + * + * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) + * + * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) + * + * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) + * or HSI_VALUE(*) multiplied/divided by the PLL factors. + * + * (*) HSI_VALUE is a constant defined in stm32f30x.h file (default value + * 8 MHz) but the real value may vary depending on the variations + * in voltage and temperature. + * + * (**) HSE_VALUE is a constant defined in stm32f30x.h file (default value + * 8 MHz), user has to ensure that HSE_VALUE is same as the real + * frequency of the crystal used. Otherwise, this function may + * have wrong result. + * + * - The result of this function could be not correct when using fractional + * value for HSE crystal. + * + * @param None + * @retval None + */ +void SystemCoreClockUpdate (void) +{ + uint32_t tmp = 0, pllmull = 0, pllsource = 0, prediv1factor = 0; + + /* Get SYSCLK source -------------------------------------------------------*/ + tmp = RCC->CFGR & RCC_CFGR_SWS; + + switch (tmp) + { + case 0x00: /* HSI used as system clock */ + SystemCoreClock = HSI_VALUE; + break; + case 0x04: /* HSE used as system clock */ + SystemCoreClock = HSE_VALUE; + break; + case 0x08: /* PLL used as system clock */ + /* Get PLL clock source and multiplication factor ----------------------*/ + pllmull = RCC->CFGR & RCC_CFGR_PLLMULL; + pllsource = RCC->CFGR & RCC_CFGR_PLLSRC; + pllmull = ( pllmull >> 18) + 2; + + if (pllsource == 0x00) + { + /* HSI oscillator clock divided by 2 selected as PLL clock entry */ + SystemCoreClock = (HSI_VALUE >> 1) * pllmull; + } + else + { + prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1; + /* HSE oscillator clock selected as PREDIV1 clock entry */ + SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; + } + break; + default: /* HSI used as system clock */ + SystemCoreClock = HSI_VALUE; + break; + } + /* Compute HCLK clock frequency ----------------*/ + /* Get HCLK prescaler */ + tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)]; + /* HCLK clock frequency */ + SystemCoreClock >>= tmp; +} + +/** + * @brief Configures the System clock source, PLL Multiplier and Divider factors, + * AHB/APBx prescalers and Flash settings + * @note This function should be called only once the RCC clock configuration + * is reset to the default reset state (done in SystemInit() function). + * @param None + * @retval None + */ +void SetSysClock(void) +{ + /* 1- Try to start with HSE and external clock */ +#if USE_PLL_HSE_EXTC != 0 + if (SetSysClock_PLL_HSE(1) == 0) +#endif + { + /* 2- If fail try to start with HSE and external xtal */ + #if USE_PLL_HSE_XTAL != 0 + if (SetSysClock_PLL_HSE(0) == 0) + #endif + { + /* 3- If fail start with HSI clock */ + if (SetSysClock_PLL_HSI() == 0) + { + while(1) + { + // [TODO] Put something here to tell the user that a problem occured... + } + } + } + } + + /* Output SYSCLK on MCO pin(PA8) for debugging purpose */ + /* + // Enable GPIOA clock + RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE); + // Configure MCO pin (PA8) + GPIO_InitTypeDef GPIO_InitStructure; + GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8; + GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; + GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF; + GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; + GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP; + GPIO_Init(GPIOA, &GPIO_InitStructure); + // Select the clock to output + RCC_MCOConfig(RCC_MCOSource_SYSCLK, RCC_MCOPrescaler_1); + */ +} + +#if (USE_PLL_HSE_XTAL != 0) || (USE_PLL_HSE_EXTC != 0) +/******************************************************************************/ +/* PLL (clocked by HSE) used as System clock source */ +/******************************************************************************/ +uint8_t SetSysClock_PLL_HSE(uint8_t bypass) +{ + __IO uint32_t StartUpCounter = 0; + __IO uint32_t HSEStatus = 0; + + /* Bypass HSE: can be done only if HSE is OFF */ + RCC->CR &= ((uint32_t)~RCC_CR_HSEON); /* To be sure HSE is OFF */ + if (bypass != 0) + { + RCC->CR |= ((uint32_t)RCC_CR_HSEBYP); + } + else + { + RCC->CR &= ((uint32_t)~RCC_CR_HSEBYP); + } + + /* Enable HSE */ + RCC->CR |= ((uint32_t)RCC_CR_HSEON); + + /* Wait till HSE is ready */ + do + { + HSEStatus = RCC->CR & RCC_CR_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + /* Check if HSE has started correctly */ + if ((RCC->CR & RCC_CR_HSERDY) != RESET) + { + /* Enable prefetch buffer and set flash latency + 0WS for 0 < SYSCLK <= 24 MHz + 1WS for 24 < SYSCLK <= 48 MHz + 2WS for 48 < SYSCLK <= 72 MHz */ + FLASH->ACR = FLASH_ACR_PRFTBE | (uint32_t)FLASH_ACR_LATENCY_1; /* 2 WS */ + + /* Warning: values are obtained with external xtal or clock = 8 MHz */ + /* SYSCLK = 72 MHz (8 MHz * 9) */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_PREDIV1 | RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLMULL9 + | RCC_CFGR_HPRE_DIV1 /* HCLK = 72 MHz */ + | RCC_CFGR_PPRE2_DIV1 /* PCLK2 = 72 MHz */ + | RCC_CFGR_PPRE1_DIV2); /* PCLK1 = 36 MHz */ + /* USBCLK = 48 MHz (72 MHz / 1.5) --> USB OK */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)RCC_CFGR_SWS_PLL) + { + } + + return 1; // OK + } + else + { + return 0; // FAIL + } +} +#endif + +/******************************************************************************/ +/* PLL (clocked by HSI) used as System clock source */ +/******************************************************************************/ +uint8_t SetSysClock_PLL_HSI(void) +{ + /* At this stage the HSI is already enabled and used as System clock source */ + + /* Enable prefetch buffer and set flash latency + 0WS for 0 < SYSCLK <= 24 MHz + 1WS for 24 < SYSCLK <= 48 MHz + 2WS for 48 < SYSCLK <= 72 MHz */ + FLASH->ACR = FLASH_ACR_PRFTBE | (uint32_t)FLASH_ACR_LATENCY_1; /* 2 WS */ + + /* SYSCLK = 64 MHz (8 MHz / 2 * 16) */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); + RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSI_Div2 | RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLMULL16 + | RCC_CFGR_HPRE_DIV1 /* HCLK = 64 MHz */ + | RCC_CFGR_PPRE2_DIV1 /* PCLK2 = 64 MHz */ + | RCC_CFGR_PPRE1_DIV2); /* PCLK1 = 32 MHz */ + /* USBCLK = 42.667 MHz (64 MHz / 1.5) --> USB NOT POSSIBLE */ + + /* Enable PLL */ + RCC->CR |= RCC_CR_PLLON; + + /* Wait till PLL is ready */ + while((RCC->CR & RCC_CR_PLLRDY) == 0) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); + RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; + + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)RCC_CFGR_SWS_PLL) + { + } + + return 1; // OK +} + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/