mbed library sources modified for open wear
Dependents: openwear-lifelogger-example
Fork of mbed-src by
targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/stm32l1xx_flash_ramfunc.c
- Committer:
- mbed_official
- Date:
- 2014-01-30
- Revision:
- 80:66393a7b209d
- Parent:
- 76:aeb1df146756
- Child:
- 106:ced8cbb51063
File content as of revision 80:66393a7b209d:
/** ****************************************************************************** * @file stm32l1xx_flash_ramfunc.c * @author MCD Application Team * @version V1.3.0 * @date 31-January-2014 * @brief This file provides all the Flash firmware functions which should be * executed from the internal SRAM. This file should be placed in * internal SRAM. * Other FLASH memory functions that can be used from the FLASH are * defined in the "stm32l1xx_flash.c" file. @verbatim *** ARM Compiler *** -------------------- [..] RAM functions are defined using the toolchain options. Functions that are be executed in RAM should reside in a separate source module. Using the 'Options for File' dialog you can simply change the 'Code / Const' area of a module to a memory space in physical RAM. Available memory areas are declared in the 'Target' tab of the Options for Target' dialog. *** ICCARM Compiler *** ----------------------- [..] RAM functions are defined using a specific toolchain keyword "__ramfunc". *** GNU Compiler *** -------------------- [..] RAM functions are defined using a specific toolchain attribute "__attribute__((section(".data")))". *** TASKING Compiler *** ------------------------ [..] RAM functions are defined using a specific toolchain pragma. This pragma is defined inside this file. @endverbatim * ****************************************************************************** * @attention * * <h2><center>© COPYRIGHT 2014 STMicroelectronics</center></h2> * * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); * You may not use this file except in compliance with the License. * You may obtain a copy of the License at: * * http://www.st.com/software_license_agreement_liberty_v2 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ #include "stm32l1xx_flash.h" /** @addtogroup STM32L1xx_StdPeriph_Driver * @{ */ /** @defgroup FLASH * @brief FLASH driver modules * @{ */ /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private function prototypes -----------------------------------------------*/ static __RAM_FUNC GetStatus(void); static __RAM_FUNC WaitForLastOperation(uint32_t Timeout); /* Private functions ---------------------------------------------------------*/ /** @defgroup FLASH_Private_Functions * @{ */ /** @addtogroup FLASH_Group1 * @verbatim @endverbatim * @{ */ #if defined ( __TASKING__ ) #pragma section_code_init on #endif /** * @brief Enable or disable the power down mode during RUN mode. * @note This function can be used only when the user code is running from Internal SRAM. * @param NewState: new state of the power down mode during RUN mode. * This parameter can be: ENABLE or DISABLE. * @retval None */ __RAM_FUNC FLASH_RUNPowerDownCmd(FunctionalState NewState) { FLASH_Status status = FLASH_COMPLETE; if (NewState != DISABLE) { /* Unlock the RUN_PD bit */ FLASH->PDKEYR = FLASH_PDKEY1; FLASH->PDKEYR = FLASH_PDKEY2; /* Set the RUN_PD bit in FLASH_ACR register to put Flash in power down mode */ FLASH->ACR |= (uint32_t)FLASH_ACR_RUN_PD; if((FLASH->ACR & FLASH_ACR_RUN_PD) != FLASH_ACR_RUN_PD) { status = FLASH_ERROR_PROGRAM; } } else { /* Clear the RUN_PD bit in FLASH_ACR register to put Flash in idle mode */ FLASH->ACR &= (uint32_t)(~(uint32_t)FLASH_ACR_RUN_PD); } /* Return the Write Status */ return status; } /** * @} */ /** @addtogroup FLASH_Group2 * @verbatim @endverbatim * @{ */ /** * @brief Erases a specified 2 page in program memory in parallel. * @note This function can be used only for STM32L1XX_HD and STM32L1XX_XL devices. * To correctly run this function, the FLASH_Unlock() function * must be called before. * Call the FLASH_Lock() to disable the flash memory access * (recommended to protect the FLASH memory against possible unwanted operation). * @param Page_Address1: The page address in program memory to be erased in * the first Bank (BANK1). This parameter should be: * - between 0x08000000 and 0x0802FF00 for STM32L1XX_HD devices * - between 0x08000000 and 0x0803FF00 for STM32L1XX_XL devices * @param Page_Address2: The page address in program memory to be erased in * the second Bank (BANK2). This parameter should be: * - between 0x08030000 and 0x0805FF00 for STM32L1XX_HD devices * - between 0x08040000 and 0x0807FF00 for STM32L1XX_XL devices * @note A Page is erased in the Program memory only if the address to load * is the start address of a page (multiple of 256 bytes). * @retval FLASH Status: The returned value can be: * FLASH_ERROR_PROGRAM, FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT. */ FLASH_Status FLASH_EraseParallelPage(uint32_t Page_Address1, uint32_t Page_Address2) { FLASH_Status status = FLASH_COMPLETE; /* Wait for last operation to be completed */ status = WaitForLastOperation(FLASH_ER_PRG_TIMEOUT); if(status == FLASH_COMPLETE) { /* If the previous operation is completed, proceed to erase the page */ /* Set the PARALLBANK bit */ FLASH->PECR |= FLASH_PECR_PARALLBANK; /* Set the ERASE bit */ FLASH->PECR |= FLASH_PECR_ERASE; /* Set PROG bit */ FLASH->PECR |= FLASH_PECR_PROG; /* Write 00000000h to the first word of the first program page to erase */ *(__IO uint32_t *)Page_Address1 = 0x00000000; /* Write 00000000h to the first word of the second program page to erase */ *(__IO uint32_t *)Page_Address2 = 0x00000000; /* Wait for last operation to be completed */ status = WaitForLastOperation(FLASH_ER_PRG_TIMEOUT); /* If the erase operation is completed, disable the ERASE, PROG and PARALLBANK bits */ FLASH->PECR &= (uint32_t)(~FLASH_PECR_PROG); FLASH->PECR &= (uint32_t)(~FLASH_PECR_ERASE); FLASH->PECR &= (uint32_t)(~FLASH_PECR_PARALLBANK); } /* Return the Erase Status */ return status; } /** * @brief Programs a half page in program memory. * @param Address: specifies the address to be written. * @param pBuffer: pointer to the buffer containing the data to be written to * the half page. * @note To correctly run this function, the FLASH_Unlock() function * must be called before. * Call the FLASH_Lock() to disable the flash memory access * (recommended to protect the FLASH memory against possible unwanted operation) * @note Half page write is possible only from SRAM. * @note If there are more than 32 words to write, after 32 words another * Half Page programming operation starts and has to be finished. * @note A half page is written to the program memory only if the first * address to load is the start address of a half page (multiple of 128 * bytes) and the 31 remaining words to load are in the same half page. * @note During the Program memory half page write all read operations are * forbidden (this includes DMA read operations and debugger read * operations such as breakpoints, periodic updates, etc.). * @note If a PGAERR is set during a Program memory half page write, the * complete write operation is aborted. Software should then reset the * FPRG and PROG/DATA bits and restart the write operation from the * beginning. * @retval FLASH Status: The returned value can be: * FLASH_ERROR_PROGRAM, FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT. */ __RAM_FUNC FLASH_ProgramHalfPage(uint32_t Address, uint32_t* pBuffer) { uint32_t count = 0; FLASH_Status status = FLASH_COMPLETE; /* Set the DISMCYCINT[0] bit in the Auxillary Control Register (0xE000E008) This bit prevents the interruption of multicycle instructions and therefore will increase the interrupt latency. of Cortex-M3. */ SCnSCB->ACTLR |= SCnSCB_ACTLR_DISMCYCINT_Msk; /* Wait for last operation to be completed */ status = WaitForLastOperation(FLASH_ER_PRG_TIMEOUT); if(status == FLASH_COMPLETE) { /* if the previous operation is completed, proceed to program the new half page */ FLASH->PECR |= FLASH_PECR_FPRG; FLASH->PECR |= FLASH_PECR_PROG; /* Write one half page directly with 32 different words */ while(count < 32) { *(__IO uint32_t*) (Address + (4 * count)) = *(pBuffer++); count ++; } /* Wait for last operation to be completed */ status = WaitForLastOperation(FLASH_ER_PRG_TIMEOUT); /* if the write operation is completed, disable the PROG and FPRG bits */ FLASH->PECR &= (uint32_t)(~FLASH_PECR_PROG); FLASH->PECR &= (uint32_t)(~FLASH_PECR_FPRG); } SCnSCB->ACTLR &= ~SCnSCB_ACTLR_DISMCYCINT_Msk; /* Return the Write Status */ return status; } /** * @brief Programs 2 half page in program memory in parallel. * @param Address1: specifies the first address to be written in the first bank * (BANK1).This parameter should be: * - between 0x08000000 and 0x0802FF80 for STM32L1XX_HD devices * - between 0x08000000 and 0x0803FF80 for STM32L1XX_XL devices * @param pBuffer1: pointer to the buffer containing the data to be written * to the first half page in the first bank. * @param Address2: specifies the second address to be written in the second bank * (BANK2). This parameter should be: * - between 0x08030000 and 0x0805FF80 for STM32L1XX_HD devices * - between 0x08040000 and 0x0807FF80 for STM32L1XX_XL devices * @param pBuffer2: pointer to the buffer containing the data to be written * to the second half page in the second bank. * @note This function can be used only for STM32L1XX_HD and STM32L1XX_XL devices. * @note To correctly run this function, the FLASH_Unlock() function * must be called before. * Call the FLASH_Lock() to disable the flash memory access * (recommended to protect the FLASH memory against possible unwanted operation). * @note Half page write is possible only from SRAM. * @note If there are more than 32 words to write, after 32 words another * Half Page programming operation starts and has to be finished. * @note A half page is written to the program memory only if the first * address to load is the start address of a half page (multiple of 128 * bytes) and the 31 remaining words to load are in the same half page. * @note During the Program memory half page write all read operations are * forbidden (this includes DMA read operations and debugger read * operations such as breakpoints, periodic updates, etc.). * @note If a PGAERR is set during a Program memory half page write, the * complete write operation is aborted. Software should then reset the * FPRG and PROG/DATA bits and restart the write operation from the * beginning. * @retval FLASH Status: The returned value can be: * FLASH_ERROR_PROGRAM, FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT. */ __RAM_FUNC FLASH_ProgramParallelHalfPage(uint32_t Address1, uint32_t* pBuffer1, uint32_t Address2, uint32_t* pBuffer2) { uint32_t count = 0; FLASH_Status status = FLASH_COMPLETE; /* Set the DISMCYCINT[0] bit in the Auxillary Control Register (0xE000E008) This bit prevents the interruption of multicycle instructions and therefore will increase the interrupt latency. of Cortex-M3. */ SCnSCB->ACTLR |= SCnSCB_ACTLR_DISMCYCINT_Msk; /* Wait for last operation to be completed */ status = WaitForLastOperation(FLASH_ER_PRG_TIMEOUT); if(status == FLASH_COMPLETE) { /* If the previous operation is completed, proceed to program the new half page */ FLASH->PECR |= FLASH_PECR_PARALLBANK; FLASH->PECR |= FLASH_PECR_FPRG; FLASH->PECR |= FLASH_PECR_PROG; /* Write the first half page directly with 32 different words */ while(count < 32) { *(__IO uint32_t*) (Address1 + (4 * count)) = *(pBuffer1++); count ++; } count = 0; /* Write the second half page directly with 32 different words */ while(count < 32) { *(__IO uint32_t*) (Address2 + (4 * count)) = *(pBuffer2++); count ++; } /* Wait for last operation to be completed */ status = WaitForLastOperation(FLASH_ER_PRG_TIMEOUT); /* if the write operation is completed, disable the PROG, FPRG and PARALLBANK bits */ FLASH->PECR &= (uint32_t)(~FLASH_PECR_PROG); FLASH->PECR &= (uint32_t)(~FLASH_PECR_FPRG); FLASH->PECR &= (uint32_t)(~FLASH_PECR_PARALLBANK); } SCnSCB->ACTLR &= ~SCnSCB_ACTLR_DISMCYCINT_Msk; /* Return the Write Status */ return status; } /** * @} */ /** @addtogroup FLASH_Group3 * @verbatim @endverbatim * @{ */ /** * @brief Erase a double word in data memory. * @param Address: specifies the address to be erased. * @note To correctly run this function, the DATA_EEPROM_Unlock() function * must be called before. * Call the DATA_EEPROM_Lock() to he data EEPROM access * and Flash program erase control register access(recommended to protect * the DATA_EEPROM against possible unwanted operation). * @note Data memory double word erase is possible only from SRAM. * @note A double word is erased to the data memory only if the first address * to load is the start address of a double word (multiple of 8 bytes). * @note During the Data memory double word erase, all read operations are * forbidden (this includes DMA read operations and debugger read * operations such as breakpoints, periodic updates, etc.). * @retval FLASH Status: The returned value can be: * FLASH_ERROR_PROGRAM, FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT. */ __RAM_FUNC DATA_EEPROM_EraseDoubleWord(uint32_t Address) { FLASH_Status status = FLASH_COMPLETE; /* Set the DISMCYCINT[0] bit in the Auxillary Control Register (0xE000E008) This bit prevents the interruption of multicycle instructions and therefore will increase the interrupt latency. of Cortex-M3. */ SCnSCB->ACTLR |= SCnSCB_ACTLR_DISMCYCINT_Msk; /* Wait for last operation to be completed */ status = WaitForLastOperation(FLASH_ER_PRG_TIMEOUT); if(status == FLASH_COMPLETE) { /* If the previous operation is completed, proceed to erase the next double word */ /* Set the ERASE bit */ FLASH->PECR |= FLASH_PECR_ERASE; /* Set DATA bit */ FLASH->PECR |= FLASH_PECR_DATA; /* Write 00000000h to the 2 words to erase */ *(__IO uint32_t *)Address = 0x00000000; Address += 4; *(__IO uint32_t *)Address = 0x00000000; /* Wait for last operation to be completed */ status = WaitForLastOperation(FLASH_ER_PRG_TIMEOUT); /* If the erase operation is completed, disable the ERASE and DATA bits */ FLASH->PECR &= (uint32_t)(~FLASH_PECR_ERASE); FLASH->PECR &= (uint32_t)(~FLASH_PECR_DATA); } SCnSCB->ACTLR &= ~SCnSCB_ACTLR_DISMCYCINT_Msk; /* Return the erase status */ return status; } /** * @brief Write a double word in data memory without erase. * @param Address: specifies the address to be written. * @param Data: specifies the data to be written. * @note To correctly run this function, the DATA_EEPROM_Unlock() function * must be called before. * Call the DATA_EEPROM_Lock() to he data EEPROM access * and Flash program erase control register access(recommended to protect * the DATA_EEPROM against possible unwanted operation). * @note Data memory double word write is possible only from SRAM. * @note A data memory double word is written to the data memory only if the * first address to load is the start address of a double word (multiple * of double word). * @note During the Data memory double word write, all read operations are * forbidden (this includes DMA read operations and debugger read * operations such as breakpoints, periodic updates, etc.). * @retval FLASH Status: The returned value can be: * FLASH_ERROR_PROGRAM, FLASH_ERROR_WRP, FLASH_COMPLETE or FLASH_TIMEOUT. */ __RAM_FUNC DATA_EEPROM_ProgramDoubleWord(uint32_t Address, uint64_t Data) { FLASH_Status status = FLASH_COMPLETE; /* Set the DISMCYCINT[0] bit in the Auxillary Control Register (0xE000E008) This bit prevents the interruption of multicycle instructions and therefore will increase the interrupt latency. of Cortex-M3. */ SCnSCB->ACTLR |= SCnSCB_ACTLR_DISMCYCINT_Msk; /* Wait for last operation to be completed */ status = WaitForLastOperation(FLASH_ER_PRG_TIMEOUT); if(status == FLASH_COMPLETE) { /* If the previous operation is completed, proceed to program the new data*/ FLASH->PECR |= FLASH_PECR_FPRG; FLASH->PECR |= FLASH_PECR_DATA; /* Write the 2 words */ *(__IO uint32_t *)Address = (uint32_t) Data; Address += 4; *(__IO uint32_t *)Address = (uint32_t) (Data >> 32); /* Wait for last operation to be completed */ status = WaitForLastOperation(FLASH_ER_PRG_TIMEOUT); /* If the write operation is completed, disable the FPRG and DATA bits */ FLASH->PECR &= (uint32_t)(~FLASH_PECR_FPRG); FLASH->PECR &= (uint32_t)(~FLASH_PECR_DATA); } SCnSCB->ACTLR &= ~SCnSCB_ACTLR_DISMCYCINT_Msk; /* Return the Write Status */ return status; } /** * @} */ /** * @brief Returns the FLASH Status. * @param None * @retval FLASH Status: The returned value can be: FLASH_BUSY, * FLASH_ERROR_PROGRAM, FLASH_ERROR_WRP or FLASH_COMPLETE */ static __RAM_FUNC GetStatus(void) { FLASH_Status FLASHstatus = FLASH_COMPLETE; if((FLASH->SR & FLASH_FLAG_BSY) == FLASH_FLAG_BSY) { FLASHstatus = FLASH_BUSY; } else { if((FLASH->SR & (uint32_t)FLASH_FLAG_WRPERR)!= (uint32_t)0x00) { FLASHstatus = FLASH_ERROR_WRP; } else { if((FLASH->SR & (uint32_t)0x1E00) != (uint32_t)0x00) { FLASHstatus = FLASH_ERROR_PROGRAM; } else { FLASHstatus = FLASH_COMPLETE; } } } /* Return the FLASH Status */ return FLASHstatus; } /** * @brief Waits for a FLASH operation to complete or a TIMEOUT to occur. * @param Timeout: FLASH programming Timeout * @retval FLASH Status: The returned value can be: FLASH_BUSY, * FLASH_ERROR_PROGRAM, FLASH_ERROR_WRP, FLASH_COMPLETE or * FLASH_TIMEOUT. */ static __RAM_FUNC WaitForLastOperation(uint32_t Timeout) { __IO FLASH_Status status = FLASH_COMPLETE; /* Check for the FLASH Status */ status = GetStatus(); /* Wait for a FLASH operation to complete or a TIMEOUT to occur */ while((status == FLASH_BUSY) && (Timeout != 0x00)) { status = GetStatus(); Timeout--; } if(Timeout == 0x00 ) { status = FLASH_TIMEOUT; } /* Return the operation status */ return status; } #if defined ( __TASKING__ ) #pragma section_code_init restore #endif /** * @} */ /** * @} */ /** * @} */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/