mbed library sources modified for open wear
Dependents: openwear-lifelogger-example
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_DISCO_F407VG/stm32f4xx_hal_uart.h
- Revision:
- 133:d4dda5c437f0
- Child:
- 242:7074e42da0b2
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_DISCO_F407VG/stm32f4xx_hal_uart.h Mon Mar 24 17:45:07 2014 +0000 @@ -0,0 +1,480 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_uart.h + * @author MCD Application Team + * @version V1.0.0 + * @date 18-February-2014 + * @brief Header file of UART HAL module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F4xx_HAL_UART_H +#define __STM32F4xx_HAL_UART_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx_hal_def.h" + +/** @addtogroup STM32F4xx_HAL_Driver + * @{ + */ + +/** @addtogroup UART + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ + +/** + * @brief UART Init Structure definition + */ +typedef struct +{ + uint32_t BaudRate; /*!< This member configures the UART communication baud rate. + The baud rate is computed using the following formula: + - IntegerDivider = ((PCLKx) / (8 * (OVR8+1) * (huart->Init.BaudRate))) + - FractionalDivider = ((IntegerDivider - ((uint32_t) IntegerDivider)) * 8 * (OVR8+1)) + 0.5 + Where OVR8 is the "oversampling by 8 mode" configuration bit in the CR1 register. */ + + uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame. + This parameter can be a value of @ref UART_Word_Length */ + + uint32_t StopBits; /*!< Specifies the number of stop bits transmitted. + This parameter can be a value of @ref UART_Stop_Bits */ + + uint32_t Parity; /*!< Specifies the parity mode. + This parameter can be a value of @ref UART_Parity + @note When parity is enabled, the computed parity is inserted + at the MSB position of the transmitted data (9th bit when + the word length is set to 9 data bits; 8th bit when the + word length is set to 8 data bits). */ + + uint32_t Mode; /*!< Specifies wether the Receive or Transmit mode is enabled or disabled. + This parameter can be a value of @ref UART_Mode */ + + uint32_t HwFlowCtl; /*!< Specifies wether the hardware flow control mode is enabled + or disabled. + This parameter can be a value of @ref UART_Hardware_Flow_Control */ + + uint32_t OverSampling; /*!< Specifies wether the Over sampling 8 is enabled or disabled, to achieve higher speed (up to fPCLK/8). + This parameter can be a value of @ref UART_Over_Sampling */ +}UART_InitTypeDef; + +/** + * @brief HAL UART State structures definition + */ +typedef enum +{ + HAL_UART_STATE_RESET = 0x00, /*!< Peripheral is not yet Initialized */ + HAL_UART_STATE_READY = 0x01, /*!< Peripheral Initialized and ready for use */ + HAL_UART_STATE_BUSY = 0x02, /*!< an internal process is ongoing */ + HAL_UART_STATE_BUSY_TX = 0x12, /*!< Data Transmission process is ongoing */ + HAL_UART_STATE_BUSY_RX = 0x22, /*!< Data Reception process is ongoing */ + HAL_UART_STATE_BUSY_TX_RX = 0x32, /*!< Data Transmission and Reception process is ongoing */ + HAL_UART_STATE_TIMEOUT = 0x03, /*!< Timeout state */ + HAL_UART_STATE_ERROR = 0x04 /*!< Error */ +}HAL_UART_StateTypeDef; + +/** + * @brief HAL UART Error Code structure definition + */ +typedef enum +{ + HAL_UART_ERROR_NONE = 0x00, /*!< No error */ + HAL_UART_ERROR_PE = 0x01, /*!< Parity error */ + HAL_UART_ERROR_NE = 0x02, /*!< Noise error */ + HAL_UART_ERROR_FE = 0x04, /*!< frame error */ + HAL_UART_ERROR_ORE = 0x08, /*!< Overrun error */ + HAL_UART_ERROR_DMA = 0x10 /*!< DMA transfer error */ +}HAL_UART_ErrorTypeDef; + +/** + * @brief UART handle Structure definition + */ +typedef struct +{ + USART_TypeDef *Instance; /* UART registers base address */ + + UART_InitTypeDef Init; /* UART communication parameters */ + + uint8_t *pTxBuffPtr; /* Pointer to UART Tx transfer Buffer */ + + uint16_t TxXferSize; /* UART Tx Transfer size */ + + uint16_t TxXferCount; /* UART Tx Transfer Counter */ + + uint8_t *pRxBuffPtr; /* Pointer to UART Rx transfer Buffer */ + + uint16_t RxXferSize; /* UART Rx Transfer size */ + + uint16_t RxXferCount; /* UART Rx Transfer Counter */ + + DMA_HandleTypeDef *hdmatx; /* UART Tx DMA Handle parameters */ + + DMA_HandleTypeDef *hdmarx; /* UART Rx DMA Handle parameters */ + + HAL_LockTypeDef Lock; /* Locking object */ + + __IO HAL_UART_StateTypeDef State; /* UART communication state */ + + __IO HAL_UART_ErrorTypeDef ErrorCode; /* UART Error code */ + +}UART_HandleTypeDef; + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup UART_Exported_Constants + * @{ + */ + +/** @defgroup UART_Word_Length + * @{ + */ +#define UART_WORDLENGTH_8B ((uint32_t)0x00000000) +#define UART_WORDLENGTH_9B ((uint32_t)USART_CR1_M) +#define IS_UART_WORD_LENGTH(LENGTH) (((LENGTH) == UART_WORDLENGTH_8B) || \ + ((LENGTH) == UART_WORDLENGTH_9B)) +/** + * @} + */ + +/** @defgroup UART_Stop_Bits + * @{ + */ +#define UART_STOPBITS_1 ((uint32_t)0x00000000) +#define UART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1) +#define IS_UART_STOPBITS(STOPBITS) (((STOPBITS) == UART_STOPBITS_1) || \ + ((STOPBITS) == UART_STOPBITS_2)) +/** + * @} + */ + +/** @defgroup UART_Parity + * @{ + */ +#define UART_PARITY_NONE ((uint32_t)0x00000000) +#define UART_PARITY_EVEN ((uint32_t)USART_CR1_PCE) +#define UART_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS)) +#define IS_UART_PARITY(PARITY) (((PARITY) == UART_PARITY_NONE) || \ + ((PARITY) == UART_PARITY_EVEN) || \ + ((PARITY) == UART_PARITY_ODD)) +/** + * @} + */ + +/** @defgroup UART_Hardware_Flow_Control + * @{ + */ +#define UART_HWCONTROL_NONE ((uint32_t)0x00000000) +#define UART_HWCONTROL_RTS ((uint32_t)USART_CR3_RTSE) +#define UART_HWCONTROL_CTS ((uint32_t)USART_CR3_CTSE) +#define UART_HWCONTROL_RTS_CTS ((uint32_t)(USART_CR3_RTSE | USART_CR3_CTSE)) +#define IS_UART_HARDWARE_FLOW_CONTROL(CONTROL)\ + (((CONTROL) == UART_HWCONTROL_NONE) || \ + ((CONTROL) == UART_HWCONTROL_RTS) || \ + ((CONTROL) == UART_HWCONTROL_CTS) || \ + ((CONTROL) == UART_HWCONTROL_RTS_CTS)) +/** + * @} + */ + +/** @defgroup UART_Mode + * @{ + */ +#define UART_MODE_RX ((uint32_t)USART_CR1_RE) +#define UART_MODE_TX ((uint32_t)USART_CR1_TE) +#define UART_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE)) +#define IS_UART_MODE(MODE) ((((MODE) & (uint32_t)0x0000FFF3) == 0x00) && ((MODE) != (uint32_t)0x000000)) +/** + * @} + */ + + /** @defgroup UART_State + * @{ + */ +#define UART_STATE_DISABLE ((uint32_t)0x00000000) +#define UART_STATE_ENABLE ((uint32_t)USART_CR1_UE) +#define IS_UART_STATE(STATE) (((STATE) == UART_STATE_DISABLE) || \ + ((STATE) == UART_STATE_ENABLE)) +/** + * @} + */ + +/** @defgroup UART_Over_Sampling + * @{ + */ +#define UART_OVERSAMPLING_16 ((uint32_t)0x00000000) +#define UART_OVERSAMPLING_8 ((uint32_t)USART_CR1_OVER8) +#define IS_UART_OVERSAMPLING(SAMPLING) (((SAMPLING) == UART_OVERSAMPLING_16) || \ + ((SAMPLING) == UART_OVERSAMPLING_8)) +/** + * @} + */ + +/** @defgroup UART_LIN_Break_Detection_Length + * @{ + */ +#define UART_LINBREAKDETECTLENGTH_10B ((uint32_t)0x00000000) +#define UART_LINBREAKDETECTLENGTH_11B ((uint32_t)0x00000020) +#define IS_UART_LIN_BREAK_DETECT_LENGTH(LENGTH) (((LENGTH) == UART_LINBREAKDETECTLENGTH_10B) || \ + ((LENGTH) == UART_LINBREAKDETECTLENGTH_11B)) +/** + * @} + */ + +/** @defgroup UART_WakeUp_functions + * @{ + */ +#define UART_WAKEUPMETHODE_IDLELINE ((uint32_t)0x00000000) +#define UART_WAKEUPMETHODE_ADDRESSMARK ((uint32_t)0x00000800) +#define IS_UART_WAKEUPMETHODE(WAKEUP) (((WAKEUP) == UART_WAKEUPMETHODE_IDLELINE) || \ + ((WAKEUP) == UART_WAKEUPMETHODE_ADDRESSMARK)) +/** + * @} + */ + +/** @defgroup UART_Flags + * Elements values convention: 0xXXXX + * - 0xXXXX : Flag mask in the SR register + * @{ + */ +#define UART_FLAG_CTS ((uint32_t)0x00000200) +#define UART_FLAG_LBD ((uint32_t)0x00000100) +#define UART_FLAG_TXE ((uint32_t)0x00000080) +#define UART_FLAG_TC ((uint32_t)0x00000040) +#define UART_FLAG_RXNE ((uint32_t)0x00000020) +#define UART_FLAG_IDLE ((uint32_t)0x00000010) +#define UART_FLAG_ORE ((uint32_t)0x00000008) +#define UART_FLAG_NE ((uint32_t)0x00000004) +#define UART_FLAG_FE ((uint32_t)0x00000002) +#define UART_FLAG_PE ((uint32_t)0x00000001) +/** + * @} + */ + +/** @defgroup UART_Interrupt_definition + * Elements values convention: 0xY000XXXX + * - XXXX : Interrupt mask in the XX register + * - Y : Interrupt source register (2bits) + * - 01: CR1 register + * - 10: CR2 register + * - 11: CR3 register + * + * @{ + */ +#define UART_IT_PE ((uint32_t)0x10000100) +#define UART_IT_TXE ((uint32_t)0x10000080) +#define UART_IT_TC ((uint32_t)0x10000040) +#define UART_IT_RXNE ((uint32_t)0x10000020) +#define UART_IT_IDLE ((uint32_t)0x10000010) + +#define UART_IT_LBD ((uint32_t)0x20000040) +#define UART_IT_CTS ((uint32_t)0x30000400) + +#define UART_IT_ERR ((uint32_t)0x30000001) + +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ + +/** @brief Checks whether the specified UART flag is set or not. + * @param __HANDLE__: specifies the UART Handle. + * This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or + * UART peripheral. + * @param __FLAG__: specifies the flag to check. + * This parameter can be one of the following values: + * @arg UART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5) + * @arg UART_FLAG_LBD: LIN Break detection flag + * @arg UART_FLAG_TXE: Transmit data register empty flag + * @arg UART_FLAG_TC: Transmission Complete flag + * @arg UART_FLAG_RXNE: Receive data register not empty flag + * @arg UART_FLAG_IDLE: Idle Line detection flag + * @arg UART_FLAG_ORE: OverRun Error flag + * @arg UART_FLAG_NE: Noise Error flag + * @arg UART_FLAG_FE: Framing Error flag + * @arg UART_FLAG_PE: Parity Error flag + * @retval The new state of __FLAG__ (TRUE or FALSE). + */ + +#define __HAL_UART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__)) + +/** @brief Clears the specified UART pending flag. + * @param __HANDLE__: specifies the UART Handle. + * This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or + * UART peripheral. + * @param __FLAG__: specifies the flag to check. + * This parameter can be any combination of the following values: + * @arg UART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5). + * @arg UART_FLAG_LBD: LIN Break detection flag. + * @arg UART_FLAG_TC: Transmission Complete flag. + * @arg UART_FLAG_RXNE: Receive data register not empty flag. + * + * @note PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun + * error) and IDLE (Idle line detected) flags are cleared by software + * sequence: a read operation to USART_SR register followed by a read + * operation to USART_DR register. + * @note RXNE flag can be also cleared by a read to the USART_DR register. + * @note TC flag can be also cleared by software sequence: a read operation to + * USART_SR register followed by a write operation to USART_DR register. + * @note TXE flag is cleared only by a write to the USART_DR register. + * + * @retval None + */ +#define __HAL_UART_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR &= ~(__FLAG__)) + +/** @brief Enables or disables the specified UART interrupt. + * @param __HANDLE__: specifies the UART Handle. + * This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or + * UART peripheral. + * @param __INTERRUPT__: specifies the UART interrupt source to check. + * This parameter can be one of the following values: + * @arg UART_IT_CTS: CTS change interrupt + * @arg UART_IT_LBD: LIN Break detection interrupt + * @arg UART_IT_TXE: Transmit Data Register empty interrupt + * @arg UART_IT_TC: Transmission complete interrupt + * @arg UART_IT_RXNE: Receive Data register not empty interrupt + * @arg UART_IT_IDLE: Idle line detection interrupt + * @arg UART_IT_PE: Parity Error interrupt + * @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error) + * @param NewState: new state of the specified UART interrupt. + * This parameter can be: ENABLE or DISABLE. + * @retval None + */ +#define UART_IT_MASK ((uint32_t)0x0000FFFF) +#define __HAL_UART_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28) == 1)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & UART_IT_MASK)): \ + (((__INTERRUPT__) >> 28) == 2)? ((__HANDLE__)->Instance->CR2 |= ((__INTERRUPT__) & UART_IT_MASK)): \ + ((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & UART_IT_MASK))) +#define __HAL_UART_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28) == 1)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & UART_IT_MASK)): \ + (((__INTERRUPT__) >> 28) == 2)? ((__HANDLE__)->Instance->CR2 &= ~((__INTERRUPT__) & UART_IT_MASK)): \ + ((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & UART_IT_MASK))) + +/** @brief Checks whether the specified UART interrupt has occurred or not. + * @param __HANDLE__: specifies the UART Handle. + * This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or + * UART peripheral. + * @param __IT__: specifies the UART interrupt source to check. + * This parameter can be one of the following values: + * @arg UART_IT_CTS: CTS change interrupt (not available for UART4 and UART5) + * @arg UART_IT_LBD: LIN Break detection interrupt + * @arg UART_IT_TXE: Transmit Data Register empty interrupt + * @arg UART_IT_TC: Transmission complete interrupt + * @arg UART_IT_RXNE: Receive Data register not empty interrupt + * @arg UART_IT_IDLE: Idle line detection interrupt + * @arg USART_IT_ERR: Error interrupt + * @retval The new state of __IT__ (TRUE or FALSE). + */ +#define __HAL_UART_GET_IT_SOURCE(__HANDLE__, __IT__) (((((__IT__) >> 28) == 1)? (__HANDLE__)->Instance->CR1:(((((uint32_t)(__IT__)) >> 28) == 2)? \ + (__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & (((uint32_t)(__IT__)) & UART_IT_MASK)) + +/** @brief macros to enables or disables the UART's one bit sampling method + * @param __HANDLE__: specifies the UART Handle. + * @retval None + */ +#define __HAL_UART_ONEBIT_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT) +#define __HAL_UART_ONEBIT_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint16_t)~((uint16_t)USART_CR3_ONEBIT)) + +#define __HAL_UART_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE) +#define __HAL_UART_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE) + +#define __DIV_SAMPLING16(_PCLK_, _BAUD_) (((_PCLK_)*25)/(4*(_BAUD_))) +#define __DIVMANT_SAMPLING16(_PCLK_, _BAUD_) (__DIV_SAMPLING16((_PCLK_), (_BAUD_))/100) +#define __DIVFRAQ_SAMPLING16(_PCLK_, _BAUD_) (((__DIV_SAMPLING16((_PCLK_), (_BAUD_)) - (__DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) * 100)) * 16 + 50) / 100) +#define __UART_BRR_SAMPLING16(_PCLK_, _BAUD_) ((__DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) << 4)|(__DIVFRAQ_SAMPLING16((_PCLK_), (_BAUD_)) & 0x0F)) + +#define __DIV_SAMPLING8(_PCLK_, _BAUD_) (((_PCLK_)*25)/(2*(_BAUD_))) +#define __DIVMANT_SAMPLING8(_PCLK_, _BAUD_) (__DIV_SAMPLING8((_PCLK_), (_BAUD_))/100) +#define __DIVFRAQ_SAMPLING8(_PCLK_, _BAUD_) (((__DIV_SAMPLING8((_PCLK_), (_BAUD_)) - (__DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) * 100)) * 16 + 50) / 100) +#define __UART_BRR_SAMPLING8(_PCLK_, _BAUD_) ((__DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) << 4)|(__DIVFRAQ_SAMPLING8((_PCLK_), (_BAUD_)) & 0x0F)) + +#define IS_UART_BAUDRATE(BAUDRATE) ((BAUDRATE) < 10500001) +#define IS_UART_ADDRESS(ADDRESS) ((ADDRESS) <= 0xF) + +/* Exported functions --------------------------------------------------------*/ +/* Initialization/de-initialization functions **********************************/ +HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength); +HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethode); +HAL_StatusTypeDef HAL_UART_DeInit (UART_HandleTypeDef *huart); +void HAL_UART_MspInit(UART_HandleTypeDef *huart); +void HAL_UART_MspDeInit(UART_HandleTypeDef *huart); + +/* IO operation functions *******************************************************/ +HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout); +HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout); +HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart); +void HAL_UART_IRQHandler(UART_HandleTypeDef *huart); +void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart); + +/* Peripheral Control functions ************************************************/ +HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_MultiProcessor_ExitMuteMode(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart); + +/* Peripheral State functions **************************************************/ +HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart); +uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart); + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F4xx_HAL_UART_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/