Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/misc.c

Revision:

76:aeb1df146756

Child:

80:66393a7b209d

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/misc.c	Mon Jan 27 14:30:07 2014 +0000
@@ -0,0 +1,251 @@
+/**
+  ******************************************************************************
+  * @file    misc.c
+  * @author  MCD Application Team
+  * @version V1.2.0
+  * @date    22-February-2013
+  * @brief   This file provides all the miscellaneous firmware functions (add-on
+  *          to CMSIS functions).
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT 2013 STMicroelectronics</center></h2>
+  *
+  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
+  * You may not use this file except in compliance with the License.
+  * You may obtain a copy of the License at:
+  *
+  *        http://www.st.com/software_license_agreement_liberty_v2
+  *
+  * Unless required by applicable law or agreed to in writing, software 
+  * distributed under the License is distributed on an "AS IS" BASIS, 
+  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+  * See the License for the specific language governing permissions and
+  * limitations under the License.
+  *
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "misc.h"
+
+/** @addtogroup STM32L1xx_StdPeriph_Driver
+  * @{
+  */
+
+/** @defgroup MISC 
+  * @brief MISC driver modules
+  * @{
+  */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+#define AIRCR_VECTKEY_MASK    ((uint32_t)0x05FA0000)
+
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup MISC_Private_Functions
+  * @{
+  */
+/**
+  *
+@verbatim
+ *******************************************************************************
+                   ##### Interrupts configuration functions #####
+ *******************************************************************************
+    [..] This section provide functions allowing to configure the NVIC interrupts 
+         (IRQ).The Cortex-M3 exceptions are managed by CMSIS functions.
+         (#) Configure the NVIC Priority Grouping using NVIC_PriorityGroupConfig() 
+             function according to the following table.
+             The table below gives the allowed values of the preemption priority 
+             and subpriority according to the Priority Grouping configuration 
+             performed by NVIC_PriorityGroupConfig function.
+  ============================================================================================================================
+    NVIC_PriorityGroup   | NVIC_IRQChannelPreemptionPriority | NVIC_IRQChannelSubPriority  | Description
+  ============================================================================================================================
+   NVIC_PriorityGroup_0  |                0                  |            0-15             |   0 bits for preemption priority
+                         |                                   |                             |   4 bits for subpriority
+  ----------------------------------------------------------------------------------------------------------------------------
+   NVIC_PriorityGroup_1  |                0-1                |            0-7              |   1 bits for preemption priority
+                         |                                   |                             |   3 bits for subpriority
+  ----------------------------------------------------------------------------------------------------------------------------
+   NVIC_PriorityGroup_2  |                0-3                |            0-3              |   2 bits for preemption priority
+                         |                                   |                             |   2 bits for subpriority
+  ----------------------------------------------------------------------------------------------------------------------------
+   NVIC_PriorityGroup_3  |                0-7                |            0-1              |   3 bits for preemption priority
+                         |                                   |                             |   1 bits for subpriority
+  ----------------------------------------------------------------------------------------------------------------------------
+   NVIC_PriorityGroup_4  |                0-15               |            0                |   4 bits for preemption priority
+                         |                                   |                             |   0 bits for subpriority
+  ============================================================================================================================
+
+
+         (#) Enable and Configure the priority of the selected IRQ Channels.  
+
+        -@- When the NVIC_PriorityGroup_0 is selected, it will no any nested interrupt,
+            the IRQ priority will be managed only by subpriority.
+            The sub-priority is only used to sort pending exception priorities, 
+            and does not affect active exceptions.
+        -@- Lower priority values gives higher priority.
+        -@- Priority Order:
+            (#@) Lowest Preemption priority.
+            (#@) Lowest Subpriority.
+            (#@) Lowest hardware priority (IRQn position).
+  
+@endverbatim
+*/
+
+/**
+  * @brief  Configures the priority grouping: preemption priority and subpriority.
+  * @param  NVIC_PriorityGroup: specifies the priority grouping bits length. 
+  *   This parameter can be one of the following values:
+  *     @arg NVIC_PriorityGroup_0: 0 bits for preemption priority
+  *                                4 bits for subpriority.
+  *     @note When NVIC_PriorityGroup_0 is selected, it will no be any nested 
+  *           interrupt. This interrupts priority is managed only with subpriority.  
+  *     @arg NVIC_PriorityGroup_1: 1 bits for preemption priority.
+  *                                3 bits for subpriority.
+  *     @arg NVIC_PriorityGroup_2: 2 bits for preemption priority.
+  *                                2 bits for subpriority.
+  *     @arg NVIC_PriorityGroup_3: 3 bits for preemption priority.
+  *                                1 bits for subpriority.
+  *     @arg NVIC_PriorityGroup_4: 4 bits for preemption priority.
+  *                                0 bits for subpriority.
+  * @retval None
+  */
+void NVIC_PriorityGroupConfig(uint32_t NVIC_PriorityGroup)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_PRIORITY_GROUP(NVIC_PriorityGroup));
+  
+  /* Set the PRIGROUP[10:8] bits according to NVIC_PriorityGroup value */
+  SCB->AIRCR = AIRCR_VECTKEY_MASK | NVIC_PriorityGroup;
+}
+
+/**
+  * @brief  Initializes the NVIC peripheral according to the specified
+  *         parameters in the NVIC_InitStruct.
+  * @note   To configure interrupts priority correctly, the NVIC_PriorityGroupConfig()
+  *         function should be called before.
+  * @param  NVIC_InitStruct: pointer to a NVIC_InitTypeDef structure that contains
+  *         the configuration information for the specified NVIC peripheral.
+  * @retval None
+  */
+void NVIC_Init(NVIC_InitTypeDef* NVIC_InitStruct)
+{
+  uint8_t tmppriority = 0x00, tmppre = 0x00, tmpsub = 0x0F;
+  
+  /* Check the parameters */
+  assert_param(IS_FUNCTIONAL_STATE(NVIC_InitStruct->NVIC_IRQChannelCmd));
+  assert_param(IS_NVIC_PREEMPTION_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority));  
+  assert_param(IS_NVIC_SUB_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelSubPriority));
+    
+  if (NVIC_InitStruct->NVIC_IRQChannelCmd != DISABLE)
+  {
+    /* Compute the Corresponding IRQ Priority --------------------------------*/    
+    tmppriority = (0x700 - ((SCB->AIRCR) & (uint32_t)0x700))>> 0x08;
+    tmppre = (0x4 - tmppriority);
+    tmpsub = tmpsub >> tmppriority;
+
+    tmppriority = (uint32_t)NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority << tmppre;
+    tmppriority |=  (uint8_t)(NVIC_InitStruct->NVIC_IRQChannelSubPriority & tmpsub);
+    tmppriority = tmppriority << 0x04;
+        
+    NVIC->IP[NVIC_InitStruct->NVIC_IRQChannel] = tmppriority;
+    
+    /* Enable the Selected IRQ Channels --------------------------------------*/
+    NVIC->ISER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] =
+      (uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F);
+  }
+  else
+  {
+    /* Disable the Selected IRQ Channels -------------------------------------*/
+    NVIC->ICER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] =
+      (uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F);
+  }
+}
+
+/**
+  * @brief  Sets the vector table location and Offset.
+  * @param  NVIC_VectTab: specifies if the vector table is in RAM or FLASH memory.
+  *   This parameter can be one of the following values:
+  *     @arg NVIC_VectTab_RAM: Vector Table in internal SRAM.
+  *     @arg NVIC_VectTab_FLASH: Vector Table in internal FLASH.
+  * @param  Offset: Vector Table base offset field. This value must be a multiple of 0x200.
+  * @retval None
+  */
+void NVIC_SetVectorTable(uint32_t NVIC_VectTab, uint32_t Offset)
+{ 
+  /* Check the parameters */
+  assert_param(IS_NVIC_VECTTAB(NVIC_VectTab));
+  assert_param(IS_NVIC_OFFSET(Offset));  
+   
+  SCB->VTOR = NVIC_VectTab | (Offset & (uint32_t)0x1FFFFF80);
+}
+
+/**
+  * @brief  Selects the condition for the system to enter low power mode.
+  * @param  LowPowerMode: Specifies the new mode for the system to enter low power mode.
+  *   This parameter can be one of the following values:
+  *     @arg NVIC_LP_SEVONPEND: Low Power SEV on Pend.
+  *     @arg NVIC_LP_SLEEPDEEP: Low Power DEEPSLEEP request.
+  *     @arg NVIC_LP_SLEEPONEXIT: Low Power Sleep on Exit.
+  * @param  NewState: new state of LP condition. 
+  *         This parameter can be: ENABLE or DISABLE.
+  * @retval None
+  */
+void NVIC_SystemLPConfig(uint8_t LowPowerMode, FunctionalState NewState)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_LP(LowPowerMode));
+  assert_param(IS_FUNCTIONAL_STATE(NewState));  
+  
+  if (NewState != DISABLE)
+  {
+    SCB->SCR |= LowPowerMode;
+  }
+  else
+  {
+    SCB->SCR &= (uint32_t)(~(uint32_t)LowPowerMode);
+  }
+}
+
+/**
+  * @brief  Configures the SysTick clock source.
+  * @param  SysTick_CLKSource: specifies the SysTick clock source.
+  *   This parameter can be one of the following values:
+  *     @arg SysTick_CLKSource_HCLK_Div8: AHB clock divided by 8 selected as SysTick clock source.
+  *     @arg SysTick_CLKSource_HCLK: AHB clock selected as SysTick clock source.
+  * @retval None
+  */
+void SysTick_CLKSourceConfig(uint32_t SysTick_CLKSource)
+{
+  /* Check the parameters */
+  assert_param(IS_SYSTICK_CLK_SOURCE(SysTick_CLKSource));
+  
+  if (SysTick_CLKSource == SysTick_CLKSource_HCLK)
+  {
+    SysTick->CTRL |= SysTick_CLKSource_HCLK;
+  }
+  else
+  {
+    SysTick->CTRL &= SysTick_CLKSource_HCLK_Div8;
+  }
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/