mbed library sources modified for open wear
Dependents: openwear-lifelogger-example
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_L053R8/stm32l0xx_hal_lptim.c
- Revision:
- 181:a4cbdfbbd2f4
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_L053R8/stm32l0xx_hal_lptim.c Wed May 07 13:15:08 2014 +0100 @@ -0,0 +1,1585 @@ +/** + ****************************************************************************** + * @file stm32l0xx_hal_lptim.c + * @author MCD Application Team + * @version V1.0.0 + * @date 22-April-2014 + * @brief LPTIM HAL module driver. + * + * This file provides firmware functions to manage the following + * functionalities of the Low Power Timer (LPTIM) peripheral: + * + Initialization and de-initialization functions. + * + Start/Stop operation functions in polling mode. + * + Start/Stop operation functions in interrupt mode. + * + Reading operation functions. + * + Peripheral State functions. + * + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] + The LPTIM HAL driver can be used as follows: + + (#)Initialize the LPTIM low level resources by implementing the + HAL_LPTIM_MspInit(): + (##) Enable the LPTIM interface clock using __LPTIM1_CLK_ENABLE(). + (##) In case of using interrupts (e.g. HAL_LPTIM_PWM_Start_IT()): + (+) Configure the LPTIM interrupt priority using HAL_NVIC_SetPriority(). + (+) Enable the LPTIM IRQ handler using HAL_NVIC_EnableIRQ(). + (+) In LPTIM IRQ handler, call HAL_LPTIM_IRQHandler(). + + (#)Initialize the LPTIM HAL using HAL_LPTIM_Init(). This function + configures mainly: + (##) The instance: Only LPTIM1 is present in STM32L053xx. + (##) Clock: the counter clock. + - Source : it can be either the ULPTIM input (IN1) or one of + the internal clock; (APB, LSE, LSI or MSI). + - Prescaler: select the clock divider. + (##) UltraLowPowerClock : To be used only if the ULPTIM is selected + as counter clock source. + - Polarity: polarity of the active edge for the counter unit + if the ULPTIM input is selected. + - SampleTime: clock sampling time to configure the clock glitch + filter. + (##) Trigger: How the counter start. + - Source: trigger can be software or one of the hardware triggers. + - ActiveEdge : only for hardware trigger. + - SampleTime : trigger sampling time to configure the trigger + glitch filter. + (##) OutputPolarity : 2 opposite polarities are possibles. + (##) UpdateMode: specifies whether the update of the autoreload and + the compare values is done immediately or after the end of current + period. + + (#)Six modes are available: + + (##) PWM Mode: To generate a PWM signal with specified period and pulse, + call HAL_LPTIM_PWM_Start() or HAL_LPTIM_PWM_Start_IT() for interruption + mode. + + (##) One Pulse Mode: To generate pulse with specified width in response + to a stimulus, call HAL_LPTIM_OnePulse_Start() or + HAL_LPTIM_OnePulse_Start_IT() for interruption mode. + + (##) Set once Mode: In this mode, the output changes the level (from + low level to high level if the output polarity is configured high, else + the opposite) when a compare match occurs. To start this mode, call + HAL_LPTIM_SetOnce_Start() or HAL_LPTIM_SetOnce_Start_IT() for + interruption mode. + + (##) Encoder Mode: To use the encoder interface call + HAL_LPTIM_Encoder_Start() or HAL_LPTIM_Encoder_Start_IT() for + interruption mode. + + (##) Time out Mode: an active edge on one selected trigger input rests + the counter. The first trigger event will start the timer, any + successive trigger event will reset the counter and the timer will + restart. To start this mode call HAL_LPTIM_TimeOut_Start_IT() or + HAL_LPTIM_TimeOut_Start_IT() for interruption mode. + + (##) Counter Mode: counter can be used to count external events on + the LPTIM Input1 or it can be used to count internal clock cycles. + To start this mode, call HAL_LPTIM_Counter_Start() or + HAL_LPTIM_Counter_Start_IT() for interruption mode. + + + (#) User can stop any process by calling the corresponding API: + HAL_LPTIM_Xxx_Stop() or HAL_LPTIM_Xxx_Stop_IT() if the process is + already started in interruption mode. + + (#)Call HAL_LPTIM_DeInit() to deinitialize the LPTIM peripheral. + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32l0xx_hal.h" + +/** @addtogroup STM32L0xx_HAL_Driver + * @{ + */ + +/** @defgroup LPTIM + * @brief LPTIM HAL module driver. + * @{ + */ + +#ifdef HAL_LPTIM_MODULE_ENABLED +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup LPTIM_Private_Functions + * @{ + */ + +/** @defgroup HAL_LPTIM_Group1 Initialization/de-initialization functions + * @brief Initialization and Configuration functions. + * +@verbatim + ============================================================================== + ##### Initialization and de-initialization functions ##### + ============================================================================== + [..] This section provides functions allowing to: + (+) Initialize the LPTIM according to the specified parameters in the + LPTIM_InitTypeDef and creates the associated handle. + (+) DeInitialize the LPTIM peripheral. + (+) Initialize the LPTIM MSP. + (+) DeInitialize LPTIM MSP. + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the LPTIM according to the specified parameters in the + * LPTIM_InitTypeDef and creates the associated handle. + * @param hlptim: LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_Init(LPTIM_HandleTypeDef *hlptim) +{ + uint32_t tmpcfgr = 0; + + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + assert_param(IS_LPTIM_CLOCK_SOURCE(hlptim->Init.Clock.Source)); + assert_param(IS_LPTIM_CLOCK_PRESCALER(hlptim->Init.Clock.Prescaler)); + if ((hlptim->Init.Clock.Source) == LPTIM_CLOCKSOURCE_ULPTIM) + { + assert_param(IS_LPTIM_CLOCK_POLARITY(hlptim->Init.UltraLowPowerClock.Polarity)); + assert_param(IS_LPTIM_CLOCK_SAMPLE_TIME(hlptim->Init.UltraLowPowerClock.SampleTime)); + } + assert_param(IS_LPTIM_TRG_SOURCE(hlptim->Init.Trigger.Source)); + if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) + { + assert_param(IS_LPTIM_TRIG_SAMPLE_TIME(hlptim->Init.Trigger.SampleTime)); + assert_param(IS_LPTIM_EXT_TRG_POLARITY(hlptim->Init.Trigger.ActiveEdge)); + } + assert_param(IS_LPTIM_OUTPUT_POLARITY(hlptim->Init.OutputPolarity)); + assert_param(IS_LPTIM_UPDATE_MODE(hlptim->Init.UpdateMode)); + assert_param(IS_LPTIM_COUNTER_SOURCE(hlptim->Init.CounterSource)); + + /* Check the LPTIM handle allocation */ + if(hlptim == NULL) + { + return HAL_ERROR; + } + + if(hlptim->State == HAL_LPTIM_STATE_RESET) + { + /* Init the low level hardware */ + HAL_LPTIM_MspInit(hlptim); + } + + /* Change the LPTIM state */ + hlptim->State = HAL_LPTIM_STATE_BUSY; + + /* Get the LPTIMx CFGR value */ + tmpcfgr = hlptim->Instance->CFGR; + + if ((hlptim->Init.Clock.Source) == LPTIM_CLOCKSOURCE_ULPTIM) + { + tmpcfgr &= (uint32_t)(~(LPTIM_CFGR_CKPOL | LPTIM_CFGR_CKFLT)); + } + if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) + { + tmpcfgr &= (uint32_t)(~ (LPTIM_CFGR_TRGFLT | LPTIM_CFGR_TRIGSEL)); + } + + /* Clear CKSEL, PRESC, TRIGEN, TRGFLT, WAVPOL, PRELOAD & COUNTMODE bits */ + tmpcfgr &= (uint32_t)(~(LPTIM_CFGR_CKSEL | LPTIM_CFGR_TRIGEN | LPTIM_CFGR_PRELOAD | + LPTIM_CFGR_WAVPOL | LPTIM_CFGR_PRESC | LPTIM_CFGR_COUNTMODE )); + + /* Set initialization parameters */ + tmpcfgr |= (hlptim->Init.Clock.Source | + hlptim->Init.Clock.Prescaler | + hlptim->Init.OutputPolarity | + hlptim->Init.UpdateMode | + hlptim->Init.CounterSource); + + if ((hlptim->Init.Clock.Source) == LPTIM_CLOCKSOURCE_ULPTIM) + { + tmpcfgr |= (hlptim->Init.UltraLowPowerClock.Polarity | + hlptim->Init.UltraLowPowerClock.SampleTime); + } + + if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) + { + /* Enable External trigger and set the trigger source */ + tmpcfgr |= (hlptim->Init.Trigger.Source | + hlptim->Init.Trigger.ActiveEdge | + hlptim->Init.Trigger.SampleTime); + } + + /* Write to LPTIMx CFGR */ + hlptim->Instance->CFGR = tmpcfgr; + + /* Change the LPTIM state */ + hlptim->State = HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief DeInitializes the LPTIM peripheral. + * @param hlptim: LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_DeInit(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the LPTIM handle allocation */ + if(hlptim == NULL) + { + return HAL_ERROR; + } + + /* Change the LPTIM state */ + hlptim->State = HAL_LPTIM_STATE_BUSY; + + /* Disable the LPTIM Peripheral Clock */ + __HAL_LPTIM_DISABLE(hlptim); + + /* DeInit the low level hardware: CLOCK, NVIC.*/ + HAL_LPTIM_MspDeInit(hlptim); + + /* Change the LPTIM state */ + hlptim->State = HAL_LPTIM_STATE_RESET; + + /* Release Lock */ + __HAL_UNLOCK(hlptim); + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Initializes the LPTIM MSP. + * @param hlptim: LPTIM handle + * @retval None + */ +__weak void HAL_LPTIM_MspInit(LPTIM_HandleTypeDef *hlptim) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_LPTIM_MspInit could be implemented in the user file + */ +} + +/** + * @brief DeInitializes LPTIM MSP. + * @param hlptim: LPTIM handle + * @retval None + */ +__weak void HAL_LPTIM_MspDeInit(LPTIM_HandleTypeDef *hlptim) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_LPTIM_MspDeInit could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup HAL_LPTIM_Group2 LPTIM Start/Stop operation functions + * @brief I/O operation functions. + * +@verbatim + ============================================================================== + ##### LPTIM Start/Stop operation functions ##### + ============================================================================== + [..] This section provides functions allowing to: + (+) Start the PWM mode. + (+) Stop the PWM mode. + (+) Start the One pulse mode. + (+) Stop the One pulse mode. + (+) Start the Set once mode. + (+) Stop the Set once mode. + (+) Start the Encoder mode. + (+) Stop the Encoder mode. + (+) Start the Timeout mode. + (+) Stop the Timeout mode. + (+) Start the Counter mode. + (+) Stop the Counter mode. + + +@endverbatim + * @{ + */ + +/** + * @brief Starts the LPTIM PWM generation. + * @param hlptim : LPTIM handle + * @param Period : Specifies the Autoreload value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @param Pulse : Specifies the compare value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_PWM_Start(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Pulse) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + assert_param(IS_LPTIM_PERIOD(Period)); + assert_param(IS_LPTIM_PULSE(Pulse)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Reset WAVE bit to set PWM mode */ + hlptim->Instance->CFGR &= ~LPTIM_CFGR_WAVE; + + /* Enable the Peripheral */ + __HAL_LPTIM_ENABLE(hlptim); + + /* Load the period value in the autoreload register */ + __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); + + /* Load the pulse value in the compare register */ + __HAL_LPTIM_COMPARE_SET(hlptim, Pulse); + + /* Start timer in continuous mode */ + __HAL_LPTIM_START_CONTINUOUS(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Stops the LPTIM PWM generation. + * @param hlptim : LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_PWM_Stop(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_LPTIM_DISABLE(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Starts the LPTIM PWM generation in interrupt mode. + * @param hlptim : LPTIM handle + * @param Period : Specifies the Autoreload value. + * This parameter must be a value between 0x0000 and 0xFFFF + * @param Pulse : Specifies the compare value. + * This parameter must be a value between 0x0000 and 0xFFFF + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_PWM_Start_IT(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Pulse) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + assert_param(IS_LPTIM_PERIOD(Period)); + assert_param(IS_LPTIM_PULSE(Pulse)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Reset WAVE bit to set PWM mode */ + hlptim->Instance->CFGR &= ~LPTIM_CFGR_WAVE; + + /* Enable Autoreload write complete interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_ARROK); + + /* Enable Compare write complete interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_CMPOK); + + /* Enable Autoreload match interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_ARRM); + + /* Enable Compare match interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_CMPM); + + /* If external trigger source is used, then enable external trigger interrupt */ + if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) + { + /* Enable external trigger interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_EXTTRIG); + } + + /* Enable the Peripheral */ + __HAL_LPTIM_ENABLE(hlptim); + + /* Load the period value in the autoreload register */ + __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); + + /* Load the pulse value in the compare register */ + __HAL_LPTIM_COMPARE_SET(hlptim, Pulse); + + /* Start timer in continuous mode */ + __HAL_LPTIM_START_CONTINUOUS(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Stops the LPTIM PWM generation in interrupt mode. + * @param hlptim : LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_PWM_Stop_IT(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_LPTIM_DISABLE(hlptim); + + /* Disable Autoreload write complete interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_ARROK); + + /* Disable Compare write complete interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_CMPOK); + + /* Disable Autoreload match interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_ARRM); + + /* Disable Compare match interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_CMPM); + + /* If external trigger source is used, then disable external trigger interrupt */ + if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) + { + /* Disable external trigger interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_EXTTRIG); + } + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Starts the LPTIM One pulse generation. + * @param hlptim : LPTIM handle + * @param Period : Specifies the Autoreload value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @param Pulse : Specifies the compare value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_OnePulse_Start(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Pulse) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + assert_param(IS_LPTIM_PERIOD(Period)); + assert_param(IS_LPTIM_PULSE(Pulse)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Reset WAVE bit to set one pulse mode */ + hlptim->Instance->CFGR &= ~LPTIM_CFGR_WAVE; + + /* Enable the Peripheral */ + __HAL_LPTIM_ENABLE(hlptim); + + /* Load the period value in the autoreload register */ + __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); + + /* Load the pulse value in the compare register */ + __HAL_LPTIM_COMPARE_SET(hlptim, Pulse); + + /* Start timer in continuous mode */ + __HAL_LPTIM_START_SINGLE(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Stops the LPTIM One pulse generation. + * @param hlptim : LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_OnePulse_Stop(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_LPTIM_DISABLE(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Starts the LPTIM One pulse generation in interrupt mode. + * @param hlptim : LPTIM handle + * @param Period : Specifies the Autoreload value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @param Pulse : Specifies the compare value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_OnePulse_Start_IT(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Pulse) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + assert_param(IS_LPTIM_PERIOD(Period)); + assert_param(IS_LPTIM_PULSE(Pulse)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Reset WAVE bit to set one pulse mode */ + hlptim->Instance->CFGR &= ~LPTIM_CFGR_WAVE; + + /* Enable Autoreload write complete interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_ARROK); + + /* Enable Compare write complete interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_CMPOK); + + /* Enable Autoreload match interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_ARRM); + + /* Enable Compare match interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_CMPM); + + /* If external trigger source is used, then enable external trigger interrupt */ + if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) + { + /* Enable external trigger interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_EXTTRIG); + } + + /* Enable the Peripheral */ + __HAL_LPTIM_ENABLE(hlptim); + + /* Load the period value in the autoreload register */ + __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); + + /* Load the pulse value in the compare register */ + __HAL_LPTIM_COMPARE_SET(hlptim, Pulse); + + /* Start timer in continuous mode */ + __HAL_LPTIM_START_SINGLE(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Stops the LPTIM One pulse generation in interrupt mode. + * @param hlptim : LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_OnePulse_Stop_IT(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_LPTIM_DISABLE(hlptim); + + /* Disable Autoreload write complete interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_ARROK); + + /* Disable Compare write complete interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_CMPOK); + + /* Disable Autoreload match interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_ARRM); + + /* Disable Compare match interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_CMPM); + + /* If external trigger source is used, then disable external trigger interrupt */ + if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) + { + /* Disable external trigger interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_EXTTRIG); + } + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Starts the LPTIM in Set once mode. + * @param hlptim : LPTIM handle + * @param Period : Specifies the Autoreload value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @param Pulse : Specifies the compare value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_SetOnce_Start(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Pulse) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + assert_param(IS_LPTIM_PERIOD(Period)); + assert_param(IS_LPTIM_PULSE(Pulse)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Set WAVE bit to enable the set once mode */ + hlptim->Instance->CFGR |= LPTIM_CFGR_WAVE; + + /* Enable the Peripheral */ + __HAL_LPTIM_ENABLE(hlptim); + + /* Load the period value in the autoreload register */ + __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); + + /* Load the pulse value in the compare register */ + __HAL_LPTIM_COMPARE_SET(hlptim, Pulse); + + /* Start timer in continuous mode */ + __HAL_LPTIM_START_SINGLE(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Stops the LPTIM Set once mode. + * @param hlptim : LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_SetOnce_Stop(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_LPTIM_DISABLE(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Starts the LPTIM Set once mode in interrupt mode. + * @param hlptim : LPTIM handle + * @param Period : Specifies the Autoreload value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @param Pulse : Specifies the compare value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_SetOnce_Start_IT(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Pulse) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + assert_param(IS_LPTIM_PERIOD(Period)); + assert_param(IS_LPTIM_PULSE(Pulse)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Set WAVE bit to enable the set once mode */ + hlptim->Instance->CFGR |= LPTIM_CFGR_WAVE; + + /* Enable Autoreload write complete interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_ARROK); + + /* Enable Compare write complete interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_CMPOK); + + /* Enable Autoreload match interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_ARRM); + + /* Enable Compare match interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_CMPM); + + /* If external trigger source is used, then enable external trigger interrupt */ + if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) + { + /* Enable external trigger interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_EXTTRIG); + } + + /* Enable the Peripheral */ + __HAL_LPTIM_ENABLE(hlptim); + + /* Load the period value in the autoreload register */ + __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); + + /* Load the pulse value in the compare register */ + __HAL_LPTIM_COMPARE_SET(hlptim, Pulse); + + /* Start timer in continuous mode */ + __HAL_LPTIM_START_SINGLE(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Stops the LPTIM Set once mode in interrupt mode. + * @param hlptim : LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_SetOnce_Stop_IT(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_LPTIM_DISABLE(hlptim); + + /* Disable Autoreload write complete interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_ARROK); + + /* Disable Compare write complete interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_CMPOK); + + /* Disable Autoreload match interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_ARRM); + + /* Disable Compare match interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_CMPM); + + /* If external trigger source is used, then disable external trigger interrupt */ + if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) + { + /* Disable external trigger interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_EXTTRIG); + } + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Starts the Encoder interface. + * @param hlptim : LPTIM handle + * @param Period : Specifies the Autoreload value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_Encoder_Start(LPTIM_HandleTypeDef *hlptim, uint32_t Period) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + assert_param(IS_LPTIM_PERIOD(Period)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Set ENC bit to enable the encoder interface */ + hlptim->Instance->CFGR |= LPTIM_CFGR_ENC; + + /* Enable the Peripheral */ + __HAL_LPTIM_ENABLE(hlptim); + + /* Load the period value in the autoreload register */ + __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); + + /* Start timer in continuous mode */ + __HAL_LPTIM_START_CONTINUOUS(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Stops the Encoder interface. + * @param hlptim : LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_Encoder_Stop(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_LPTIM_DISABLE(hlptim); + + /* Reset ENC bit to disable the encoder interface */ + hlptim->Instance->CFGR &= ~LPTIM_CFGR_ENC; + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Starts the Encoder interface in interrupt mode. + * @param hlptim : LPTIM handle + * @param Period : Specifies the Autoreload value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_Encoder_Start_IT(LPTIM_HandleTypeDef *hlptim, uint32_t Period) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + assert_param(IS_LPTIM_PERIOD(Period)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Set ENC bit to enable the encoder interface */ + hlptim->Instance->CFGR |= LPTIM_CFGR_ENC; + + /* Enable "switch to down direction" interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_DOWN); + + /* Enable "switch to up direction" interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_UP); + + /* Enable the Peripheral */ + __HAL_LPTIM_ENABLE(hlptim); + + /* Load the period value in the autoreload register */ + __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); + + /* Start timer in continuous mode */ + __HAL_LPTIM_START_CONTINUOUS(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Stops the Encoder interface in nterrupt mode. + * @param hlptim : LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_Encoder_Stop_IT(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_LPTIM_DISABLE(hlptim); + + /* Reset ENC bit to disable the encoder interface */ + hlptim->Instance->CFGR &= ~LPTIM_CFGR_ENC; + + /* Disable "switch to down direction" interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_DOWN); + + /* Disable "switch to up direction" interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_UP); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Starts the Timeout function. The first trigger event will start the + * timer, any successive trigger event will reset the counter and + * the timer restarts. + * @param hlptim : LPTIM handle + * @param Period : Specifies the Autoreload value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @param Timeout : Specifies the TimeOut value to rest the counter. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_TimeOut_Start(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Timeout) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + assert_param(IS_LPTIM_PERIOD(Period)); + assert_param(IS_LPTIM_PULSE(Timeout)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Reset WAVE bit to set PWM mode */ + hlptim->Instance->CFGR &= ~LPTIM_CFGR_WAVE; + + /* Set TIMOUT bit to enable the timeout function */ + hlptim->Instance->CFGR |= LPTIM_CFGR_TIMOUT; + + /* Enable the Peripheral */ + __HAL_LPTIM_ENABLE(hlptim); + + /* Load the period value in the autoreload register */ + __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); + + /* Load the Timeout value in the compare register */ + __HAL_LPTIM_COMPARE_SET(hlptim, Timeout); + + /* Start timer in continuous mode */ + __HAL_LPTIM_START_CONTINUOUS(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Stops the Timeout function. + * @param hlptim : LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_TimeOut_Stop(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_LPTIM_DISABLE(hlptim); + + /* Reset TIMOUT bit to enable the timeout function */ + hlptim->Instance->CFGR &= ~LPTIM_CFGR_TIMOUT; + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Starts the Timeout function in interrupt mode. The first trigger + * event will start the timer, any successive trigger event will reset + * the counter and the timer restarts. + * @param hlptim : LPTIM handle + * @param Period : Specifies the Autoreload value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @param Timeout : Specifies the TimeOut value to rest the counter. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_TimeOut_Start_IT(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Timeout) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + assert_param(IS_LPTIM_PERIOD(Period)); + assert_param(IS_LPTIM_PULSE(Timeout)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Reset WAVE bit to set PWM mode */ + hlptim->Instance->CFGR &= ~LPTIM_CFGR_WAVE; + + /* Set TIMOUT bit to enable the timeout function */ + hlptim->Instance->CFGR |= LPTIM_CFGR_TIMOUT; + + + /* Enable Compare match interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_CMPM); + + /* Enable the Peripheral */ + __HAL_LPTIM_ENABLE(hlptim); + + /* Load the period value in the autoreload register */ + __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); + + /* Load the Timeout value in the compare register */ + __HAL_LPTIM_COMPARE_SET(hlptim, Timeout); + + /* Start timer in continuous mode */ + __HAL_LPTIM_START_CONTINUOUS(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Stops the Timeout function in interrupt mode. + * @param hlptim : LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_TimeOut_Stop_IT(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_LPTIM_DISABLE(hlptim); + + /* Reset TIMOUT bit to enable the timeout function */ + hlptim->Instance->CFGR &= ~LPTIM_CFGR_TIMOUT; + + /* Disable Autoreload write complete interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_ARROK); + + /* Disable Compare write complete interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_CMPOK); + + /* Disable Autoreload match interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_ARRM); + + /* Disable Compare match interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_CMPM); + + /* Disable external trigger interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_EXTTRIG); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Starts the Counter mode. + * @param hlptim : LPTIM handle + * @param Period : Specifies the Autoreload value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_Counter_Start(LPTIM_HandleTypeDef *hlptim, uint32_t Period) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + assert_param(IS_LPTIM_PERIOD(Period)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* If clock source is not ULPTIM clock, then it must not be prescaled */ + if (hlptim->Init.Clock.Source != LPTIM_CLOCKSOURCE_ULPTIM) + { + /* Check if clock is prescaled */ + assert_param(IS_LPTIM_CLOCK_PRESCALERDIV1(hlptim->Init.Clock.Prescaler)); + /* Set clock prescaler to 0 */ + hlptim->Instance->CFGR &= ~LPTIM_CFGR_PRESC; + } + + /* Enable the Peripheral */ + __HAL_LPTIM_ENABLE(hlptim); + + /* Load the period value in the autoreload register */ + __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); + + /* Start timer in continuous mode */ + __HAL_LPTIM_START_CONTINUOUS(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Stops the Counter mode. + * @param hlptim : LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_Counter_Stop(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_LPTIM_DISABLE(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Starts the Counter mode in interrupt mode. + * @param hlptim : LPTIM handle + * @param Period : Specifies the Autoreload value. + * This parameter must be a value between 0x0000 and 0xFFFF. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_Counter_Start_IT(LPTIM_HandleTypeDef *hlptim, uint32_t Period) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + assert_param(IS_LPTIM_PERIOD(Period)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* If clock source is not ULPTIM clock, then it must not be prescaled */ + if (hlptim->Init.Clock.Source != LPTIM_CLOCKSOURCE_ULPTIM) + { + /* Check if clock is prescaled */ + assert_param(IS_LPTIM_CLOCK_PRESCALERDIV1(hlptim->Init.Clock.Prescaler)); + /* Set clock prescaler to 0 */ + hlptim->Instance->CFGR &= ~LPTIM_CFGR_PRESC; + } + + /* Enable Autoreload write complete interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_ARROK); + + /* Enable Autoreload match interrupt */ + __HAL_LPTIM_ENABLE_INTERRUPT(hlptim, LPTIM_IT_ARRM); + + /* Enable the Peripheral */ + __HAL_LPTIM_ENABLE(hlptim); + + /* Load the period value in the autoreload register */ + __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); + + /* Start timer in continuous mode */ + __HAL_LPTIM_START_CONTINUOUS(hlptim); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @brief Stops the Counter mode in interrupt mode. + * @param hlptim : LPTIM handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LPTIM_Counter_Stop_IT(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + /* Set the LPTIM state */ + hlptim->State= HAL_LPTIM_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_LPTIM_DISABLE(hlptim); + + /* Disable Autoreload write complete interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_ARROK); + + /* Disable Autoreload match interrupt */ + __HAL_LPTIM_DISABLE_INTERRUPT(hlptim, LPTIM_IT_ARRM); + + /* Change the TIM state*/ + hlptim->State= HAL_LPTIM_STATE_READY; + + /* Return function status */ + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup HAL_LPTIM_Group3 LPTIM Read operation functions + * @brief Read operation functions. + * +@verbatim + ============================================================================== + ##### LPTIM Reading operation functions ##### + ============================================================================== +[..] This section provides LPTIM Reading functions. + (+) Read the counter value. + (+) Read the period (Auto-reload) value. + (+) Read the pulse (Compare)value. +@endverbatim + * @{ + */ + +/** + * @brief This function returns the current counter value. + * @param hlptim: LPTIM handle + * @retval Counter value. + */ +uint32_t HAL_LPTIM_ReadCounter(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + return (hlptim->Instance->CNT); +} + +/** + * @brief This function return the current Autoreload (Period) value. + * @param hlptim: LPTIM handle + * @retval Autoreload value. + */ +uint32_t HAL_LPTIM_ReadAutoReload(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + return (hlptim->Instance->ARR); +} + +/** + * @brief This function return the current Compare (Pulse) value. + * @param hlptim: LPTIM handle + * @retval Compare value. + */ +uint32_t HAL_LPTIM_ReadCompare(LPTIM_HandleTypeDef *hlptim) +{ + /* Check the parameters */ + assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); + + return (hlptim->Instance->CMP); +} + +/** + * @} + */ + + + +/** @defgroup HAL_LPTIM_Group4 LPTIM IRQ handler + * @brief LPTIM IRQ handler. + * +@verbatim + ============================================================================== + ##### LPTIM IRQ handler ##### + ============================================================================== +[..] This section provides LPTIM IRQ handler function. + +@endverbatim + * @{ + */ + +/** + * @brief This function handles LPTIM interrupt request. + * @param hlptim: LPTIM handle + * @retval None + */ +void HAL_LPTIM_IRQHandler(LPTIM_HandleTypeDef *hlptim) +{ + /* Compare match interrupt */ + if(__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_CMPM) != RESET) + { + if(__HAL_LPTIM_GET_ITSTATUS(hlptim, LPTIM_IT_CMPM) !=RESET) + { + /* Clear Compare match flag */ + __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPM); + + /* Compare match Callback */ + HAL_LPTIM_CompareMatchCallback(hlptim); + } + } + + /* Autoreload match interrupt */ + if(__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_ARRM) != RESET) + { + if(__HAL_LPTIM_GET_ITSTATUS(hlptim, LPTIM_IT_ARRM) !=RESET) + { + /* Clear Autoreload match flag */ + __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARRM); + + /* Autoreload match Callback */ + HAL_LPTIM_AutoReloadMatchCallback(hlptim); + } + } + + /* Trigger detected interrupt */ + if(__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_EXTTRIG) != RESET) + { + if(__HAL_LPTIM_GET_ITSTATUS(hlptim, LPTIM_IT_EXTTRIG) !=RESET) + { + /* Clear Trigger detected flag */ + __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_EXTTRIG); + + /* Trigger detected callback */ + HAL_LPTIM_TriggerCallback(hlptim); + } + } + + /* Compare write interrupt */ + if(__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_CMPOK) != RESET) + { + if(__HAL_LPTIM_GET_ITSTATUS(hlptim, LPTIM_IT_CMPOK) !=RESET) + { + /* Clear Compare write flag */ + __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPOK); + + /* Compare write Callback */ + HAL_LPTIM_CompareWriteCallback(hlptim); + } + } + + /* Autoreload write interrupt */ + if(__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_ARROK) != RESET) + { + if(__HAL_LPTIM_GET_ITSTATUS(hlptim, LPTIM_IT_ARROK) !=RESET) + { + /* Clear Autoreload write flag */ + __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); + + /* Autoreload write Callback */ + HAL_LPTIM_AutoReloadWriteCallback(hlptim); + } + } + + /* Direction counter changed from Down to Up interrupt */ + if(__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_UP) != RESET) + { + if(__HAL_LPTIM_GET_ITSTATUS(hlptim, LPTIM_IT_UP) !=RESET) + { + /* Clear Direction counter changed from Down to Up flag */ + __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_UP); + + /* Direction counter changed from Down to Up Callback */ + HAL_LPTIM_DirectionUpCallback(hlptim); + } + } + + /* Direction counter changed from Up to Down interrupt */ + if(__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_DOWN) != RESET) + { + if(__HAL_LPTIM_GET_ITSTATUS(hlptim, LPTIM_IT_DOWN) !=RESET) + { + /* Clear Direction counter changed from Up to Down flag */ + __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_DOWN); + + /* Direction counter changed from Up to Down Callback */ + HAL_LPTIM_DirectionDownCallback(hlptim); + } + } +} + +/** + * @brief Compare match callback in non blocking mode + * @param hlptim : LPTIM handle + * @retval None + */ +__weak void HAL_LPTIM_CompareMatchCallback(LPTIM_HandleTypeDef *hlptim) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_LPTIM_CompareMatchCallback could be implemented in the user file + */ +} + +/** + * @brief Autoreload match callback in non blocking mode + * @param hlptim : LPTIM handle + * @retval None + */ +__weak void HAL_LPTIM_AutoReloadMatchCallback(LPTIM_HandleTypeDef *hlptim) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_LPTIM_AutoReloadMatchCallback could be implemented in the user file + */ +} + +/** + * @brief Trigger detected callback in non blocking mode + * @param hlptim : LPTIM handle + * @retval None + */ +__weak void HAL_LPTIM_TriggerCallback(LPTIM_HandleTypeDef *hlptim) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_LPTIM_TriggerCallback could be implemented in the user file + */ +} + +/** + * @brief Compare write callback in non blocking mode + * @param hlptim : LPTIM handle + * @retval None + */ +__weak void HAL_LPTIM_CompareWriteCallback(LPTIM_HandleTypeDef *hlptim) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_LPTIM_CompareWriteCallback could be implemented in the user file + */ +} + +/** + * @brief Autoreload write callback in non blocking mode + * @param hlptim : LPTIM handle + * @retval None + */ +__weak void HAL_LPTIM_AutoReloadWriteCallback(LPTIM_HandleTypeDef *hlptim) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_LPTIM_AutoReloadWriteCallback could be implemented in the user file + */ +} + +/** + * @brief Direction counter changed from Down to Up callback in non blocking mode + * @param hlptim : LPTIM handle + * @retval None + */ +__weak void HAL_LPTIM_DirectionUpCallback(LPTIM_HandleTypeDef *hlptim) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_LPTIM_DirectionUpCallback could be implemented in the user file + */ +} + +/** + * @brief Direction counter changed from Up to Down callback in non blocking mode + * @param hlptim : LPTIM handle + * @retval None + */ +__weak void HAL_LPTIM_DirectionDownCallback(LPTIM_HandleTypeDef *hlptim) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_LPTIM_DirectionDownCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup HAL_LPTIM_Group5 Peripheral State functions + * @brief Peripheral State functions. + * +@verbatim + ============================================================================== + ##### Peripheral State functions ##### + ============================================================================== + [..] + This subsection permits to get in run-time the status of the peripheral. + +@endverbatim + * @{ + */ + +/** + * @brief Returns the LPTIM state. + * @param hlptim: LPTIM handle + * @retval HAL state + */ +HAL_LPTIM_StateTypeDef HAL_LPTIM_GetState(LPTIM_HandleTypeDef *hlptim) +{ + return hlptim->State; +} + +/** + * @} + */ + + +/** + * @} + */ + +#endif /* HAL_LPTIM_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/