mbed library sources modified for open wear
Dependents: openwear-lifelogger-example
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_DISCO_F051R8/stm32f0xx_gpio.c
- Revision:
- 130:1dec54e4aec3
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_DISCO_F051R8/stm32f0xx_gpio.c Fri Mar 21 11:45:09 2014 +0000 @@ -0,0 +1,550 @@ +/** + ****************************************************************************** + * @file stm32f0xx_gpio.c + * @author MCD Application Team + * @version V1.3.0 + * @date 16-January-2014 + * @brief This file provides firmware functions to manage the following + * functionalities of the GPIO peripheral: + * + Initialization and Configuration functions + * + GPIO Read and Write functions + * + GPIO Alternate functions configuration functions + * + * @verbatim + * + * + =========================================================================== + ##### How to use this driver ##### + =========================================================================== + [..] + (#) Enable the GPIO AHB clock using RCC_AHBPeriphClockCmd() + (#) Configure the GPIO pin(s) using GPIO_Init() + Four possible configuration are available for each pin: + (++) Input: Floating, Pull-up, Pull-down. + (++) Output: Push-Pull (Pull-up, Pull-down or no Pull) + Open Drain (Pull-up, Pull-down or no Pull). + In output mode, the speed is configurable: Low, Medium, Fast or High. + (++) Alternate Function: Push-Pull (Pull-up, Pull-down or no Pull) + Open Drain (Pull-up, Pull-down or no Pull). + (++) Analog: required mode when a pin is to be used as ADC channel, + DAC output or comparator input. + (#) Peripherals alternate function: + (++) For ADC, DAC and comparators, configure the desired pin in analog + mode using GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AN + (++) For other peripherals (TIM, USART...): + (+++) Connect the pin to the desired peripherals' Alternate + Function (AF) using GPIO_PinAFConfig() function. For PortC, + PortD and PortF, no configuration is needed. + (+++) Configure the desired pin in alternate function mode using + GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AF + (+++) Select the type, pull-up/pull-down and output speed via + GPIO_PuPd, GPIO_OType and GPIO_Speed members + (+++) Call GPIO_Init() function + (#) To get the level of a pin configured in input mode use GPIO_ReadInputDataBit() + (#) To set/reset the level of a pin configured in output mode use + GPIO_SetBits()/GPIO_ResetBits() + (#) During and just after reset, the alternate functions are not active and + the GPIO pins are configured in input floating mode (except JTAG pins). + (#) The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as + general-purpose (PC14 and PC15, respectively) when the LSE oscillator + is off. The LSE has priority over the GPIO function. + (#) The HSE oscillator pins OSC_IN/OSC_OUT can be used as general-purpose + PD0 and PD1, respectively, when the HSE oscillator is off. The HSE has + priority over the GPIO function. + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f0xx_gpio.h" +#include "stm32f0xx_rcc.h" + +/** @addtogroup STM32F0xx_StdPeriph_Driver + * @{ + */ + +/** @defgroup GPIO + * @brief GPIO driver modules + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup GPIO_Private_Functions + * @{ + */ + +/** @defgroup GPIO_Group1 Initialization and Configuration + * @brief Initialization and Configuration + * +@verbatim + =============================================================================== + ##### Initialization and Configuration ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Deinitializes the GPIOx peripheral registers to their default reset + * values. + * @param GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral. + * @note GPIOE is available only for STM32F072. + * @note GPIOD is not available for STM32F031. + * @retval None + */ +void GPIO_DeInit(GPIO_TypeDef* GPIOx) +{ + /* Check the parameters */ + assert_param(IS_GPIO_ALL_PERIPH(GPIOx)); + + if(GPIOx == GPIOA) + { + RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOA, ENABLE); + RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOA, DISABLE); + } + else if(GPIOx == GPIOB) + { + RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOB, ENABLE); + RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOB, DISABLE); + } + else if(GPIOx == GPIOC) + { + RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOC, ENABLE); + RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOC, DISABLE); + } + else if(GPIOx == GPIOD) + { + RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOD, ENABLE); + RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOD, DISABLE); + } + else if(GPIOx == GPIOE) + { + RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOE, ENABLE); + RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOE, DISABLE); + } + else + { + if(GPIOx == GPIOF) + { + RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOF, ENABLE); + RCC_AHBPeriphResetCmd(RCC_AHBPeriph_GPIOF, DISABLE); + } + } +} + +/** + * @brief Initializes the GPIOx peripheral according to the specified + * parameters in the GPIO_InitStruct. + * @param GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral. + * @note GPIOE is available only for STM32F072. + * @note GPIOD is not available for STM32F031. + * @param GPIO_InitStruct: pointer to a GPIO_InitTypeDef structure that contains + * the configuration information for the specified GPIO peripheral. + * @retval None + */ +void GPIO_Init(GPIO_TypeDef* GPIOx, GPIO_InitTypeDef* GPIO_InitStruct) +{ + uint32_t pinpos = 0x00, pos = 0x00 , currentpin = 0x00; + + /* Check the parameters */ + assert_param(IS_GPIO_ALL_PERIPH(GPIOx)); + assert_param(IS_GPIO_PIN(GPIO_InitStruct->GPIO_Pin)); + assert_param(IS_GPIO_MODE(GPIO_InitStruct->GPIO_Mode)); + assert_param(IS_GPIO_PUPD(GPIO_InitStruct->GPIO_PuPd)); + + /*-------------------------- Configure the port pins -----------------------*/ + /*-- GPIO Mode Configuration --*/ + for (pinpos = 0x00; pinpos < 0x10; pinpos++) + { + pos = ((uint32_t)0x01) << pinpos; + + /* Get the port pins position */ + currentpin = (GPIO_InitStruct->GPIO_Pin) & pos; + + if (currentpin == pos) + { + if ((GPIO_InitStruct->GPIO_Mode == GPIO_Mode_OUT) || (GPIO_InitStruct->GPIO_Mode == GPIO_Mode_AF)) + { + /* Check Speed mode parameters */ + assert_param(IS_GPIO_SPEED(GPIO_InitStruct->GPIO_Speed)); + + /* Speed mode configuration */ + GPIOx->OSPEEDR &= ~(GPIO_OSPEEDER_OSPEEDR0 << (pinpos * 2)); + GPIOx->OSPEEDR |= ((uint32_t)(GPIO_InitStruct->GPIO_Speed) << (pinpos * 2)); + + /* Check Output mode parameters */ + assert_param(IS_GPIO_OTYPE(GPIO_InitStruct->GPIO_OType)); + + /* Output mode configuration */ + GPIOx->OTYPER &= ~((GPIO_OTYPER_OT_0) << ((uint16_t)pinpos)); + GPIOx->OTYPER |= (uint16_t)(((uint16_t)GPIO_InitStruct->GPIO_OType) << ((uint16_t)pinpos)); + } + + GPIOx->MODER &= ~(GPIO_MODER_MODER0 << (pinpos * 2)); + + GPIOx->MODER |= (((uint32_t)GPIO_InitStruct->GPIO_Mode) << (pinpos * 2)); + + /* Pull-up Pull down resistor configuration */ + GPIOx->PUPDR &= ~(GPIO_PUPDR_PUPDR0 << ((uint16_t)pinpos * 2)); + GPIOx->PUPDR |= (((uint32_t)GPIO_InitStruct->GPIO_PuPd) << (pinpos * 2)); + } + } +} + +/** + * @brief Fills each GPIO_InitStruct member with its default value. + * @param GPIO_InitStruct: pointer to a GPIO_InitTypeDef structure which will + * be initialized. + * @retval None + */ +void GPIO_StructInit(GPIO_InitTypeDef* GPIO_InitStruct) +{ + /* Reset GPIO init structure parameters values */ + GPIO_InitStruct->GPIO_Pin = GPIO_Pin_All; + GPIO_InitStruct->GPIO_Mode = GPIO_Mode_IN; + GPIO_InitStruct->GPIO_Speed = GPIO_Speed_Level_2; + GPIO_InitStruct->GPIO_OType = GPIO_OType_PP; + GPIO_InitStruct->GPIO_PuPd = GPIO_PuPd_NOPULL; +} + +/** + * @brief Locks GPIO Pins configuration registers. + * @note The locked registers are GPIOx_MODER, GPIOx_OTYPER, GPIOx_OSPEEDR, + * GPIOx_PUPDR, GPIOx_AFRL and GPIOx_AFRH. + * @note The configuration of the locked GPIO pins can no longer be modified + * until the next device reset. + * @param GPIOx: where x can be (A or B) to select the GPIO peripheral. + * @param GPIO_Pin: specifies the port bit to be written. + * This parameter can be any combination of GPIO_Pin_x where x can be (0..15). + * @retval None + */ +void GPIO_PinLockConfig(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) +{ + __IO uint32_t tmp = 0x00010000; + + /* Check the parameters */ + assert_param(IS_GPIO_LIST_PERIPH(GPIOx)); + assert_param(IS_GPIO_PIN(GPIO_Pin)); + + tmp |= GPIO_Pin; + /* Set LCKK bit */ + GPIOx->LCKR = tmp; + /* Reset LCKK bit */ + GPIOx->LCKR = GPIO_Pin; + /* Set LCKK bit */ + GPIOx->LCKR = tmp; + /* Read LCKK bit */ + tmp = GPIOx->LCKR; + /* Read LCKK bit */ + tmp = GPIOx->LCKR; +} + +/** + * @} + */ + +/** @defgroup GPIO_Group2 GPIO Read and Write + * @brief GPIO Read and Write + * +@verbatim + =============================================================================== + ##### GPIO Read and Write ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Reads the specified input port pin. + * @param GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral. + * @note GPIOE is available only for STM32F072. + * @note GPIOD is not available for STM32F031. + * @param GPIO_Pin: specifies the port bit to read. + * @note This parameter can be GPIO_Pin_x where x can be: + * For STM32F051 and STM32F030: (0..15) for GPIOA, GPIOB, GPIOC, (2) for GPIOD and (0..1, 4..7) for GIIOF. + * For STM32F072: (0..15) for GPIOA, GPIOB, GPIOC, GPIOD, GPIOE, (0..10) for GPIOF. + * For STM32F031: (0..15) for GPIOA, GPIOB, (13..15) for GPIOC and (0..1, 6..7) for GPIOF. + * @retval The input port pin value. + */ +uint8_t GPIO_ReadInputDataBit(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) +{ + uint8_t bitstatus = 0x00; + + /* Check the parameters */ + assert_param(IS_GPIO_ALL_PERIPH(GPIOx)); + assert_param(IS_GET_GPIO_PIN(GPIO_Pin)); + + if ((GPIOx->IDR & GPIO_Pin) != (uint32_t)Bit_RESET) + { + bitstatus = (uint8_t)Bit_SET; + } + else + { + bitstatus = (uint8_t)Bit_RESET; + } + return bitstatus; +} + +/** + * @brief Reads the specified input port pin. + * @param GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral. + * @note GPIOE is available only for STM32F072. + * @note GPIOD is not available for STM32F031. + * @retval The input port pin value. + */ +uint16_t GPIO_ReadInputData(GPIO_TypeDef* GPIOx) +{ + /* Check the parameters */ + assert_param(IS_GPIO_ALL_PERIPH(GPIOx)); + + return ((uint16_t)GPIOx->IDR); +} + +/** + * @brief Reads the specified output data port bit. + * @param GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral. + * @note GPIOE is available only for STM32F072. + * @note GPIOD is not available for STM32F031. + * @param GPIO_Pin: Specifies the port bit to read. + * @note This parameter can be GPIO_Pin_x where x can be: + * For STM32F051 and STM32F030: (0..15) for GPIOA, GPIOB, GPIOC, (2) for GPIOD and (0..1, 4..7) for GIIOF. + * For STM32F072: (0..15) for GPIOA, GPIOB, GPIOC, GPIOD, GPIOE, (0..10) for GPIOF. + * For STM32F031: (0..15) for GPIOA, GPIOB, (13..15) for GPIOC and (0..1, 6..7) for GPIOF. + * @retval The output port pin value. + */ +uint8_t GPIO_ReadOutputDataBit(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) +{ + uint8_t bitstatus = 0x00; + + /* Check the parameters */ + assert_param(IS_GPIO_ALL_PERIPH(GPIOx)); + assert_param(IS_GET_GPIO_PIN(GPIO_Pin)); + + if ((GPIOx->ODR & GPIO_Pin) != (uint32_t)Bit_RESET) + { + bitstatus = (uint8_t)Bit_SET; + } + else + { + bitstatus = (uint8_t)Bit_RESET; + } + return bitstatus; +} + +/** + * @brief Reads the specified GPIO output data port. + * @param GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral. + * @note GPIOE is available only for STM32F072. + * @note GPIOD is not available for STM32F031. + * @retval GPIO output data port value. + */ +uint16_t GPIO_ReadOutputData(GPIO_TypeDef* GPIOx) +{ + /* Check the parameters */ + assert_param(IS_GPIO_ALL_PERIPH(GPIOx)); + + return ((uint16_t)GPIOx->ODR); +} + +/** + * @brief Sets the selected data port bits. + * @param GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral. + * @note GPIOE is available only for STM32F072. + * @note GPIOD is not available for STM32F031. + * @param GPIO_Pin: specifies the port bits to be written. + * @note This parameter can be GPIO_Pin_x where x can be: + * For STM32F051 and STM32F030: (0..15) for GPIOA, GPIOB, GPIOC, (2) for GPIOD and (0..1, 4..7) for GIIOF. + * For STM32F072: (0..15) for GPIOA, GPIOB, GPIOC, GPIOD, GPIOE, (0..10) for GPIOF. + * For STM32F031: (0..15) for GPIOA, GPIOB, (13..15) for GPIOC and (0..1, 6..7) for GPIOF. + * @retval None + */ +void GPIO_SetBits(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) +{ + /* Check the parameters */ + assert_param(IS_GPIO_ALL_PERIPH(GPIOx)); + assert_param(IS_GPIO_PIN(GPIO_Pin)); + + GPIOx->BSRR = GPIO_Pin; +} + +/** + * @brief Clears the selected data port bits. + * @param GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral. + * @note GPIOE is available only for STM32F072. + * @note GPIOD is not available for STM32F031. + * @param GPIO_Pin: specifies the port bits to be written. + * @note This parameter can be GPIO_Pin_x where x can be: + * For STM32F051 and STM32F030: (0..15) for GPIOA, GPIOB, GPIOC, (2) for GPIOD and (0..1, 4..7) for GIIOF. + * For STM32F072: (0..15) for GPIOA, GPIOB, GPIOC, GPIOD, GPIOE, (0..10) for GPIOF. + * For STM32F031: (0..15) for GPIOA, GPIOB, (13..15) for GPIOC and (0..1, 6..7) for GPIOF. + * @retval None + */ +void GPIO_ResetBits(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) +{ + /* Check the parameters */ + assert_param(IS_GPIO_ALL_PERIPH(GPIOx)); + assert_param(IS_GPIO_PIN(GPIO_Pin)); + + GPIOx->BRR = GPIO_Pin; +} + +/** + * @brief Sets or clears the selected data port bit. + * @param GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral. + * @note GPIOE is available only for STM32F072. + * @note GPIOD is not available for STM32F031. + * @param GPIO_Pin: specifies the port bit to be written. + * @param BitVal: specifies the value to be written to the selected bit. + * This parameter can be one of the BitAction enumeration values: + * @arg Bit_RESET: to clear the port pin + * @arg Bit_SET: to set the port pin + * @note This parameter can be GPIO_Pin_x where x can be: + * For STM32F051 and STM32F030: (0..15) for GPIOA, GPIOB, GPIOC, (2) for GPIOD and (0..1, 4..7) for GIIOF. + * For STM32F072: (0..15) for GPIOA, GPIOB, GPIOC, GPIOD, GPIOE, (0..10) for GPIOF. + * For STM32F031: (0..15) for GPIOA, GPIOB, (13..15) for GPIOC and (0..1, 6..7) for GPIOF. + * @retval None + */ +void GPIO_WriteBit(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, BitAction BitVal) +{ + /* Check the parameters */ + assert_param(IS_GPIO_ALL_PERIPH(GPIOx)); + assert_param(IS_GET_GPIO_PIN(GPIO_Pin)); + assert_param(IS_GPIO_BIT_ACTION(BitVal)); + + if (BitVal != Bit_RESET) + { + GPIOx->BSRR = GPIO_Pin; + } + else + { + GPIOx->BRR = GPIO_Pin ; + } +} + +/** + * @brief Writes data to the specified GPIO data port. + * @param GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral. + * @note GPIOE is available only for STM32F072. + * @note GPIOD is not available for STM32F031. + * @param PortVal: specifies the value to be written to the port output data register. + * @retval None + */ +void GPIO_Write(GPIO_TypeDef* GPIOx, uint16_t PortVal) +{ + /* Check the parameters */ + assert_param(IS_GPIO_ALL_PERIPH(GPIOx)); + + GPIOx->ODR = PortVal; +} + +/** + * @} + */ + +/** @defgroup GPIO_Group3 GPIO Alternate functions configuration functions + * @brief GPIO Alternate functions configuration functions + * +@verbatim + =============================================================================== + ##### GPIO Alternate functions configuration functions ##### + =============================================================================== + +@endverbatim + * @{ + */ + +/** + * @brief Writes data to the specified GPIO data port. + * @param GPIOx: where x can be (A, B, C, D, E or F) to select the GPIO peripheral. + * @note GPIOC, GPIOD, GPIOE and GPIOF are available only for STM32F072. + * @param GPIO_PinSource: specifies the pin for the Alternate function. + * This parameter can be GPIO_PinSourcex where x can be (0..15) for GPIOA, GPIOB, GPIOD, GPIOE + * and (0..12) for GPIOC and (0, 2..5, 9..10) for GPIOF. + * @param GPIO_AF: selects the pin to used as Alternate function. + * This parameter can be one of the following value: + * @arg GPIO_AF_0: WKUP, EVENTOUT, TIM15, SPI1, TIM17, MCO, SWDAT, SWCLK, + * TIM14, BOOT, USART1, CEC, IR_OUT, SPI2, TIM3, USART4, + * CAN, USART2, CRS, TIM16, TIM1, TS + * @arg GPIO_AF_1: USART2, CEC, TIM3, USART1, USART2, EVENTOUT, I2C1, + * I2C2, TIM15, SPI2, USART3, TS, SPI1 + * @arg GPIO_AF_2: TIM2, TIM1, EVENTOUT, TIM16, TIM17, USB + * @arg GPIO_AF_3: TS, I2C1, TIM15, EVENTOUT + * @arg GPIO_AF_4: TIM14, USART4, USART3, CRS, CAN + * @arg GPIO_AF_5: TIM16, TIM17, TIM15, SPI2, I2C2 + * @arg GPIO_AF_6: EVENTOUT + * @arg GPIO_AF_7: COMP1 OUT, COMP2 OUT + * @note The pin should already been configured in Alternate Function mode(AF) + * using GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AF + * @note Refer to the Alternate function mapping table in the device datasheet + * for the detailed mapping of the system and peripherals'alternate + * function I/O pins. + * @retval None + */ +void GPIO_PinAFConfig(GPIO_TypeDef* GPIOx, uint16_t GPIO_PinSource, uint8_t GPIO_AF) +{ + uint32_t temp = 0x00; + uint32_t temp_2 = 0x00; + + /* Check the parameters */ + assert_param(IS_GPIO_ALL_PERIPH(GPIOx)); + assert_param(IS_GPIO_PIN_SOURCE(GPIO_PinSource)); + assert_param(IS_GPIO_AF(GPIO_AF)); + + temp = ((uint32_t)(GPIO_AF) << ((uint32_t)((uint32_t)GPIO_PinSource & (uint32_t)0x07) * 4)); + GPIOx->AFR[GPIO_PinSource >> 0x03] &= ~((uint32_t)0xF << ((uint32_t)((uint32_t)GPIO_PinSource & (uint32_t)0x07) * 4)); + temp_2 = GPIOx->AFR[GPIO_PinSource >> 0x03] | temp; + GPIOx->AFR[GPIO_PinSource >> 0x03] = temp_2; +} + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/