tarou yamada / nucleo_rotary_encoder

Dependents:   serial_connected_mcu_nucleo rotary_encoder_mbed serial_connected_mcu_nucleo omuni_speed_pid ... more

Fork of rotary_encoder by tarou yamada

このライブラリは以下のプログラムに基いています https://developer.mbed.org/users/gregeric/code/Nucleo_Hello_Encoder/

HAL_TIM_Encoder_MspInit/EncoderMspInitL1.cpp

Committer:
inst
Date:
2016-06-25
Revision:
10:684e1604e5ea
Parent:
9:d1e6284a13ab

File content as of revision 10:684e1604e5ea:

#include "mbed.h"
/*
 * HAL_TIM_Encoder_MspInit()
 * Overrides the __weak function stub in stm32l4xx_hal_tim.h
 *
 * Edit the below for your preferred pin wiring & pullup/down
 * I have encoder common at 3V3, using GPIO_PULLDOWN on inputs.
 * Encoder A&B outputs connected directly to GPIOs.
 *
 * http://www.st.com/st-web-ui/static/active/en/resource/technical/document/datasheet/DM00098321.pdf
 * Table 9 has GPIO alternate function pinout mappings.
 *
 * TIM2_CH1: AF1 @ PA_0, PA_5, PA_15, PE_9
 * TIM2_CH2: AF1 @ PA_1, PB_3, PE_10
 *
 * TIM3_CH1: AF2 @ PA_6, PB_4, PC_6, PE_3
 * TIM3_CH2: AF2 @ PA_7, PB_5, PC_7, PE_4
 *
 * TIM4_CH1: AF2 @ PB_6, PD_12
 * TIM4_CH2: AF2 @ PB_7, PD_13
 *
 * TIM5_CH1: AF2 @ PA_0*    *TIM5 used by mbed system ticker so unavailable
 * TIM5_CH2: AF2 @ PA_1*
 *
 */

#ifdef TARGET_STM32L1
void HAL_TIM_Encoder_MspInit(TIM_HandleTypeDef *htim)
{
    GPIO_InitTypeDef GPIO_InitStruct;

    if (htim->Instance == TIM2) { //PA0 PA1 = Nucleo A0 A1
        __TIM2_CLK_ENABLE();
        __GPIOA_CLK_ENABLE();
        GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1;
        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
        GPIO_InitStruct.Pull = GPIO_PULLDOWN;
        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
        GPIO_InitStruct.Alternate = GPIO_AF1_TIM2;
        HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
    }
    else if (htim->Instance == TIM3) { //PB4 PB5 = Nucleo D5 D4
        __TIM3_CLK_ENABLE();
        __GPIOB_CLK_ENABLE();
        GPIO_InitStruct.Pin = GPIO_PIN_4 | GPIO_PIN_5;
        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
        GPIO_InitStruct.Pull = GPIO_PULLDOWN;
        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
        GPIO_InitStruct.Alternate = GPIO_AF2_TIM3;
        HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
    }
    else if (htim->Instance == TIM4) { // PB6 PB7 = Nucleo D10 MORPHO_PB7
        __TIM4_CLK_ENABLE();
        __GPIOB_CLK_ENABLE();
        GPIO_InitStruct.Pin = GPIO_PIN_6 | GPIO_PIN_7;
        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
        GPIO_InitStruct.Pull = GPIO_PULLDOWN;
        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
        GPIO_InitStruct.Alternate = GPIO_AF2_TIM4;
        HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
    }
}
#endif