ilkay KOZAK
V148
Fork of
RadioHead-148
by 
David Rimer
RH_RF95.h
- Committer:
- davidr99
- Date:
- 2015-10-15
- Revision:
- 0:ab4e012489ef
File content as of revision 0:ab4e012489ef:
// RH_RF95.h
//
// Definitions for HopeRF LoRa radios per:
// http://www.hoperf.com/upload/rf/RFM95_96_97_98W.pdf
// http://www.hoperf.cn/upload/rfchip/RF96_97_98.pdf
//
// Author: Mike McCauley (mikem@airspayce.com)
// Copyright (C) 2014 Mike McCauley
// $Id: RH_RF95.h,v 1.7 2015/05/17 00:11:26 mikem Exp $
//
#ifndef RH_RF95_h
#define RH_RF95_h
#include <RHSPIDriver.h>
// This is the maximum number of interrupts the driver can support
// Most Arduinos can handle 2, Megas can handle more
#define RH_RF95_NUM_INTERRUPTS 3
// Max number of octets the LORA Rx/Tx FIFO can hold
#define RH_RF95_FIFO_SIZE 255
// This is the maximum number of bytes that can be carried by the LORA.
// We use some for headers, keeping fewer for RadioHead messages
#define RH_RF95_MAX_PAYLOAD_LEN RH_RF95_FIFO_SIZE
// The length of the headers we add.
// The headers are inside the LORA's payload
#define RH_RF95_HEADER_LEN 4
// This is the maximum message length that can be supported by this driver.
// Can be pre-defined to a smaller size (to save SRAM) prior to including this header
// Here we allow for 1 byte message length, 4 bytes headers, user data and 2 bytes of FCS
#ifndef RH_RF95_MAX_MESSAGE_LEN
#define RH_RF95_MAX_MESSAGE_LEN (RH_RF95_MAX_PAYLOAD_LEN - RH_RF95_HEADER_LEN)
#endif
// The crystal oscillator frequency of the module
#define RH_RF95_FXOSC 32000000.0
// The Frequency Synthesizer step = RH_RF95_FXOSC / 2^^19
#define RH_RF95_FSTEP (RH_RF95_FXOSC / 524288)
// Register names (LoRa Mode, from table 85)
#define RH_RF95_REG_00_FIFO 0x00
#define RH_RF95_REG_01_OP_MODE 0x01
#define RH_RF95_REG_02_RESERVED 0x02
#define RH_RF95_REG_03_RESERVED 0x03
#define RH_RF95_REG_04_RESERVED 0x04
#define RH_RF95_REG_05_RESERVED 0x05
#define RH_RF95_REG_06_FRF_MSB 0x06
#define RH_RF95_REG_07_FRF_MID 0x07
#define RH_RF95_REG_08_FRF_LSB 0x08
#define RH_RF95_REG_09_PA_CONFIG 0x09
#define RH_RF95_REG_0A_PA_RAMP 0x0a
#define RH_RF95_REG_0B_OCP 0x0b
#define RH_RF95_REG_0C_LNA 0x0c
#define RH_RF95_REG_0D_FIFO_ADDR_PTR 0x0d
#define RH_RF95_REG_0E_FIFO_TX_BASE_ADDR 0x0e
#define RH_RF95_REG_0F_FIFO_RX_BASE_ADDR 0x0f
#define RH_RF95_REG_10_FIFO_RX_CURRENT_ADDR 0x10
#define RH_RF95_REG_11_IRQ_FLAGS_MASK 0x11
#define RH_RF95_REG_12_IRQ_FLAGS 0x12
#define RH_RF95_REG_13_RX_NB_BYTES 0x13
#define RH_RF95_REG_14_RX_HEADER_CNT_VALUE_MSB 0x14
#define RH_RF95_REG_15_RX_HEADER_CNT_VALUE_LSB 0x15
#define RH_RF95_REG_16_RX_PACKET_CNT_VALUE_MSB 0x16
#define RH_RF95_REG_17_RX_PACKET_CNT_VALUE_LSB 0x17
#define RH_RF95_REG_18_MODEM_STAT 0x18
#define RH_RF95_REG_19_PKT_SNR_VALUE 0x19
#define RH_RF95_REG_1A_PKT_RSSI_VALUE 0x1a
#define RH_RF95_REG_1B_RSSI_VALUE 0x1b
#define RH_RF95_REG_1C_HOP_CHANNEL 0x1c
#define RH_RF95_REG_1D_MODEM_CONFIG1 0x1d
#define RH_RF95_REG_1E_MODEM_CONFIG2 0x1e
#define RH_RF95_REG_1F_SYMB_TIMEOUT_LSB 0x1f
#define RH_RF95_REG_20_PREAMBLE_MSB 0x20
#define RH_RF95_REG_21_PREAMBLE_LSB 0x21
#define RH_RF95_REG_22_PAYLOAD_LENGTH 0x22
#define RH_RF95_REG_23_MAX_PAYLOAD_LENGTH 0x23
#define RH_RF95_REG_24_HOP_PERIOD 0x24
#define RH_RF95_REG_25_FIFO_RX_BYTE_ADDR 0x25
#define RH_RF95_REG_26_MODEM_CONFIG3 0x26
#define RH_RF95_REG_40_DIO_MAPPING1 0x40
#define RH_RF95_REG_41_DIO_MAPPING2 0x41
#define RH_RF95_REG_42_VERSION 0x42
#define RH_RF95_REG_4B_TCXO 0x4b
#define RH_RF95_REG_4D_PA_DAC 0x4d
#define RH_RF95_REG_5B_FORMER_TEMP 0x5b
#define RH_RF95_REG_61_AGC_REF 0x61
#define RH_RF95_REG_62_AGC_THRESH1 0x62
#define RH_RF95_REG_63_AGC_THRESH2 0x63
#define RH_RF95_REG_64_AGC_THRESH3 0x64
// RH_RF95_REG_01_OP_MODE 0x01
#define RH_RF95_LONG_RANGE_MODE 0x80
#define RH_RF95_ACCESS_SHARED_REG 0x40
#define RH_RF95_MODE 0x07
#define RH_RF95_MODE_SLEEP 0x00
#define RH_RF95_MODE_STDBY 0x01
#define RH_RF95_MODE_FSTX 0x02
#define RH_RF95_MODE_TX 0x03
#define RH_RF95_MODE_FSRX 0x04
#define RH_RF95_MODE_RXCONTINUOUS 0x05
#define RH_RF95_MODE_RXSINGLE 0x06
#define RH_RF95_MODE_CAD 0x07
// RH_RF95_REG_09_PA_CONFIG 0x09
#define RH_RF95_PA_SELECT 0x80
#define RH_RF95_OUTPUT_POWER 0x0f
// RH_RF95_REG_0A_PA_RAMP 0x0a
#define RH_RF95_LOW_PN_TX_PLL_OFF 0x10
#define RH_RF95_PA_RAMP 0x0f
#define RH_RF95_PA_RAMP_3_4MS 0x00
#define RH_RF95_PA_RAMP_2MS 0x01
#define RH_RF95_PA_RAMP_1MS 0x02
#define RH_RF95_PA_RAMP_500US 0x03
#define RH_RF95_PA_RAMP_250US 0x0
#define RH_RF95_PA_RAMP_125US 0x05
#define RH_RF95_PA_RAMP_100US 0x06
#define RH_RF95_PA_RAMP_62US 0x07
#define RH_RF95_PA_RAMP_50US 0x08
#define RH_RF95_PA_RAMP_40US 0x09
#define RH_RF95_PA_RAMP_31US 0x0a
#define RH_RF95_PA_RAMP_25US 0x0b
#define RH_RF95_PA_RAMP_20US 0x0c
#define RH_RF95_PA_RAMP_15US 0x0d
#define RH_RF95_PA_RAMP_12US 0x0e
#define RH_RF95_PA_RAMP_10US 0x0f
// RH_RF95_REG_0B_OCP 0x0b
#define RH_RF95_OCP_ON 0x20
#define RH_RF95_OCP_TRIM 0x1f
// RH_RF95_REG_0C_LNA 0x0c
#define RH_RF95_LNA_GAIN 0xe0
#define RH_RF95_LNA_BOOST 0x03
#define RH_RF95_LNA_BOOST_DEFAULT 0x00
#define RH_RF95_LNA_BOOST_150PC 0x11
// RH_RF95_REG_11_IRQ_FLAGS_MASK 0x11
#define RH_RF95_RX_TIMEOUT_MASK 0x80
#define RH_RF95_RX_DONE_MASK 0x40
#define RH_RF95_PAYLOAD_CRC_ERROR_MASK 0x20
#define RH_RF95_VALID_HEADER_MASK 0x10
#define RH_RF95_TX_DONE_MASK 0x08
#define RH_RF95_CAD_DONE_MASK 0x04
#define RH_RF95_FHSS_CHANGE_CHANNEL_MASK 0x02
#define RH_RF95_CAD_DETECTED_MASK 0x01
// RH_RF95_REG_12_IRQ_FLAGS 0x12
#define RH_RF95_RX_TIMEOUT 0x80
#define RH_RF95_RX_DONE 0x40
#define RH_RF95_PAYLOAD_CRC_ERROR 0x20
#define RH_RF95_VALID_HEADER 0x10
#define RH_RF95_TX_DONE 0x08
#define RH_RF95_CAD_DONE 0x04
#define RH_RF95_FHSS_CHANGE_CHANNEL 0x02
#define RH_RF95_CAD_DETECTED 0x01
// RH_RF95_REG_18_MODEM_STAT 0x18
#define RH_RF95_RX_CODING_RATE 0xe0
#define RH_RF95_MODEM_STATUS_CLEAR 0x10
#define RH_RF95_MODEM_STATUS_HEADER_INFO_VALID 0x08
#define RH_RF95_MODEM_STATUS_RX_ONGOING 0x04
#define RH_RF95_MODEM_STATUS_SIGNAL_SYNCHRONIZED 0x02
#define RH_RF95_MODEM_STATUS_SIGNAL_DETECTED 0x01
// RH_RF95_REG_1C_HOP_CHANNEL 0x1c
#define RH_RF95_PLL_TIMEOUT 0x80
#define RH_RF95_RX_PAYLOAD_CRC_IS_ON 0x40
#define RH_RF95_FHSS_PRESENT_CHANNEL 0x3f
// RH_RF95_REG_1D_MODEM_CONFIG1 0x1d
#define RH_RF95_BW 0xc0
#define RH_RF95_BW_125KHZ 0x00
#define RH_RF95_BW_250KHZ 0x40
#define RH_RF95_BW_500KHZ 0x80
#define RH_RF95_BW_RESERVED 0xc0
#define RH_RF95_CODING_RATE 0x38
#define RH_RF95_CODING_RATE_4_5 0x00
#define RH_RF95_CODING_RATE_4_6 0x08
#define RH_RF95_CODING_RATE_4_7 0x10
#define RH_RF95_CODING_RATE_4_8 0x18
#define RH_RF95_IMPLICIT_HEADER_MODE_ON 0x04
#define RH_RF95_RX_PAYLOAD_CRC_ON 0x02
#define RH_RF95_LOW_DATA_RATE_OPTIMIZE 0x01
// RH_RF95_REG_1E_MODEM_CONFIG2 0x1e
#define RH_RF95_SPREADING_FACTOR 0xf0
#define RH_RF95_SPREADING_FACTOR_64CPS 0x60
#define RH_RF95_SPREADING_FACTOR_128CPS 0x70
#define RH_RF95_SPREADING_FACTOR_256CPS 0x80
#define RH_RF95_SPREADING_FACTOR_512CPS 0x90
#define RH_RF95_SPREADING_FACTOR_1024CPS 0xa0
#define RH_RF95_SPREADING_FACTOR_2048CPS 0xb0
#define RH_RF95_SPREADING_FACTOR_4096CPS 0xc0
#define RH_RF95_TX_CONTINUOUS_MOE 0x08
#define RH_RF95_AGC_AUTO_ON 0x04
#define RH_RF95_SYM_TIMEOUT_MSB 0x03
// RH_RF95_REG_4D_PA_DAC 0x4d
#define RH_RF95_PA_DAC_DISABLE 0x04
#define RH_RF95_PA_DAC_ENABLE 0x07
/////////////////////////////////////////////////////////////////////
/// \class RH_RF95 RH_RF95.h <RH_RF95.h>
/// \brief Driver to send and receive unaddressed, unreliable datagrams via a LoRa
/// capable radio transceiver.
///
/// For Semtech SX1276/77/78 and HopeRF RFM95/96/97/98 and other similar LoRa capable radios.
/// Based on http://www.hoperf.com/upload/rf/RFM95_96_97_98W.pdf
/// and http://www.hoperf.cn/upload/rfchip/RF96_97_98.pdf
/// and http://www.semtech.com/images/datasheet/LoraDesignGuide_STD.pdf
/// and http://www.semtech.com/images/datasheet/sx1276.pdf
/// FSK/GFSK/OOK modes are not (yet) supported.
///
/// Works with
/// - the excellent MiniWirelessLoRa from Anarduino http://www.anarduino.com/miniwireless
///
/// \par Overview
///
/// This class provides basic functions for sending and receiving unaddressed,
/// unreliable datagrams of arbitrary length to 251 octets per packet.
///
/// Manager classes may use this class to implement reliable, addressed datagrams and streams,
/// mesh routers, repeaters, translators etc.
///
/// Naturally, for any 2 radios to communicate that must be configured to use the same frequency and
/// modulation scheme.
///
/// This Driver provides an object-oriented interface for sending and receiving data messages with Hope-RF
/// RFM95/96/97/98(W) and compatible radio modules in LoRa mode.
///
/// The Hope-RF (http://www.hoperf.com) RFM95/96/97/98(W) is a low-cost ISM transceiver
/// chip. It supports FSK, GFSK, OOK over a wide range of frequencies and
/// programmable data rates, and it also supports the proprietary LoRA (Long Range) mode, which
/// is the only mode supported in this RadioHead driver.
///
/// This Driver provides functions for sending and receiving messages of up
/// to 251 octets on any frequency supported by the radio, in a range of
/// predefined Bandwidths, Spreading Factors and Coding Rates. Frequency can be set with
/// 61Hz precision to any frequency from 240.0MHz to 960.0MHz. Caution: most modules only support a more limited
/// range of frequencies due to antenna tuning.
///
/// Up to 2 RFM95/96/97/98(W) modules can be connected to an Arduino (3 on a Mega),
/// permitting the construction of translators and frequency changers, etc.
///
/// Support for other features such as transmitter power control etc is
/// also provided.
///
/// Tested on MinWirelessLoRa with arduino-1.0.5
/// on OpenSuSE 13.1
///
/// \par Packet Format
///
/// All messages sent and received by this RH_RF95 Driver conform to this packet format:
///
/// - LoRa mode:
/// - 8 symbol PREAMBLE
/// - Explicit header with header CRC (handled internally by the radio)
/// - 4 octets HEADER: (TO, FROM, ID, FLAGS)
/// - 0 to 251 octets DATA
/// - CRC (handled internally by the radio)
///
/// \par Connecting RFM95/96/97/98 to Arduino
///
/// We tested with Anarduino MiniWirelessLoRA, which is an Arduino Duemilanove compatible with a RFM96W
/// module on-board. Therefore it needs no connections other than the USB
/// programming connection and an antenna to make it work.
///
/// If you have a bare RFM95/96/97/98 that you want to connect to an Arduino, you
/// might use these connections (untested): CAUTION: you must use a 3.3V type
/// Arduino, otherwise you will also need voltage level shifters between the
/// Arduino and the RFM95. CAUTION, you must also ensure you connect an
/// antenna.
///
/// \code
/// Arduino RFM95/96/97/98
/// GND----------GND (ground in)
/// 3V3----------3.3V (3.3V in)
/// interrupt 0 pin D2-----------DIO0 (interrupt request out)
/// SS pin D10----------NSS (chip select in)
/// SCK pin D13----------SCK (SPI clock in)
/// MOSI pin D11----------MOSI (SPI Data in)
/// MISO pin D12----------MISO (SPI Data out)
/// \endcode
///
/// With these connections, you can then use the default constructor RH_RF95().
/// You can override the default settings for the SS pin and the interrupt in
/// the RH_RF95 constructor if you wish to connect the slave select SS to other
/// than the normal one for your Arduino (D10 for Diecimila, Uno etc and D53
/// for Mega) or the interrupt request to other than pin D2 (Caution,
/// different processors have different constraints as to the pins available
/// for interrupts).
///
/// It is possible to have 2 or more radios connected to one Arduino, provided
/// each radio has its own SS and interrupt line (SCK, SDI and SDO are common
/// to all radios)
///
/// Caution: on some Arduinos such as the Mega 2560, if you set the slave
/// select pin to be other than the usual SS pin (D53 on Mega 2560), you may
/// need to set the usual SS pin to be an output to force the Arduino into SPI
/// master mode.
///
/// Caution: Power supply requirements of the RFM module may be relevant in some circumstances:
/// RFM95/96/97/98 modules are capable of pulling 120mA+ at full power, where Arduino's 3.3V line can
/// give 50mA. You may need to make provision for alternate power supply for
/// the RFM module, especially if you wish to use full transmit power, and/or you have
/// other shields demanding power. Inadequate power for the RFM is likely to cause symptoms such as:
/// - reset's/bootups terminate with "init failed" messages
/// - random termination of communication after 5-30 packets sent/received
/// - "fake ok" state, where initialization passes fluently, but communication doesn't happen
/// - shields hang Arduino boards, especially during the flashing
///
/// \par Interrupts
///
/// The RH_RF95 driver uses interrupts to react to events in the RFM module,
/// such as the reception of a new packet, or the completion of transmission
/// of a packet. The RH_RF95 driver interrupt service routine reads status from
/// and writes data to the the RFM module via the SPI interface. It is very
/// important therefore, that if you are using the RH_RF95 driver with another
/// SPI based deviced, that you disable interrupts while you transfer data to
/// and from that other device. Use cli() to disable interrupts and sei() to
/// reenable them.
///
/// \par Memory
///
/// The RH_RF95 driver requires non-trivial amounts of memory. The sample
/// programs all compile to about 8kbytes each, which will fit in the
/// flash proram memory of most Arduinos. However, the RAM requirements are
/// more critical. Therefore, you should be vary sparing with RAM use in
/// programs that use the RH_RF95 driver.
///
/// It is often hard to accurately identify when you are hitting RAM limits on Arduino.
/// The symptoms can include:
/// - Mysterious crashes and restarts
/// - Changes in behaviour when seemingly unrelated changes are made (such as adding print() statements)
/// - Hanging
/// - Output from Serial.print() not appearing
///
/// \par Range
///
/// We have made some simple range tests under the following conditions:
/// - rf95_client base station connected to a VHF discone antenna at 8m height above ground
/// - rf95_server mobile connected to 17.3cm 1/4 wavelength antenna at 1m height, no ground plane.
/// - Both configured for 13dBm, 434MHz, Bw = 125 kHz, Cr = 4/8, Sf = 4096chips/symbol, CRC on. Slow+long range
/// - Minimum reported RSSI seen for successful comms was about -91
/// - Range over flat ground through heavy trees and vegetation approx 2km.
/// - At 20dBm (100mW) otherwise identical conditions approx 3km.
/// - At 20dBm, along salt water flat sandy beach, 3.2km.
///
/// It should be noted that at this data rate, a 12 octet message takes 2 seconds to transmit.
///
/// At 20dBm (100mW) with Bw = 125 kHz, Cr = 4/5, Sf = 128chips/symbol, CRC on.
/// (Default medium range) in the conditions described above.
/// - Range over flat ground through heavy trees and vegetation approx 2km.
///
/// \par Transmitter Power
///
/// You can control the transmitter power on the RF transceiver
/// with the RH_RF95::setTxPower() function. The argument can be any of
/// +5 to +23
/// The default is 13. Eg:
/// \code
/// driver.setTxPower(10);
/// \endcode
///
/// We have made some actual power measurements against
/// programmed power for Anarduino MiniWirelessLoRa (which has RFM96W-433Mhz installed)
/// - MiniWirelessLoRa RFM96W-433Mhz, USB power
/// - 30cm RG316 soldered direct to RFM96W module ANT and GND
/// - SMA connector
/// - 12db attenuator
/// - SMA connector
/// - MiniKits AD8307 HF/VHF Power Head (calibrated against Rohde&Schwartz 806.2020 test set)
/// - Tektronix TDS220 scope to measure the Vout from power head
/// \code
/// Program power Measured Power
/// dBm dBm
/// 5 5
/// 7 7
/// 9 8
/// 11 11
/// 13 13
/// 15 15
/// 17 16
/// 19 18
/// 20 20
/// 21 21
/// 22 22
/// 23 23
/// \endcode
/// (Caution: we dont claim laboratory accuracy for these measurements)
/// You would not expect to get anywhere near these powers to air with a simple 1/4 wavelength wire antenna.
class RH_RF95 : public RHSPIDriver
{
public:
/// \brief Defines register values for a set of modem configuration registers
///
/// Defines register values for a set of modem configuration registers
/// that can be passed to setModemRegisters() if none of the choices in
/// ModemConfigChoice suit your need setModemRegisters() writes the
/// register values from this structure to the appropriate registers
/// to set the desired spreading factor, coding rate and bandwidth
typedef struct {
uint8_t reg_1d; ///< Value for register RH_RF95_REG_1D_MODEM_CONFIG1
uint8_t reg_1e; ///< Value for register RH_RF95_REG_1E_MODEM_CONFIG2
uint8_t reg_26; ///< Value for register RH_RF95_REG_26_MODEM_CONFIG3
} ModemConfig;
/// Choices for setModemConfig() for a selected subset of common
/// data rates. If you need another configuration,
/// determine the necessary settings and call setModemRegisters() with your
/// desired settings. It might be helpful to use the LoRa calculator mentioned in
/// http://www.semtech.com/images/datasheet/LoraDesignGuide_STD.pdf
/// These are indexes into MODEM_CONFIG_TABLE. We strongly recommend you use these symbolic
/// definitions and not their integer equivalents: its possible that new values will be
/// introduced in later versions (though we will try to avoid it).
typedef enum {
Bw125Cr45Sf128 = 0, ///< Bw = 125 kHz, Cr = 4/5, Sf = 128chips/symbol, CRC on. Default medium range
Bw500Cr45Sf128, ///< Bw = 500 kHz, Cr = 4/5, Sf = 128chips/symbol, CRC on. Fast+short range
Bw31_25Cr48Sf512, ///< Bw = 31.25 kHz, Cr = 4/8, Sf = 512chips/symbol, CRC on. Slow+long range
Bw125Cr48Sf4096, ///< Bw = 125 kHz, Cr = 4/8, Sf = 4096chips/symbol, CRC on. Slow+long range
} ModemConfigChoice;
/// Constructor. You can have multiple instances, but each instance must have its own
/// interrupt and slave select pin. After constructing, you must call init() to initialise the interface
/// and the radio module. A maximum of 3 instances can co-exist on one processor, provided there are sufficient
/// distinct interrupt lines, one for each instance.
/// \param[in] slaveSelectPin the Arduino pin number of the output to use to select the RH_RF22 before
/// accessing it. Defaults to the normal SS pin for your Arduino (D10 for Diecimila, Uno etc, D53 for Mega, D10 for Maple)
/// \param[in] interruptPin The interrupt Pin number that is connected to the RFM DIO0 interrupt line.
/// Defaults to pin 2, as required by Anarduino MinWirelessLoRa module.
/// Caution: You must specify an interrupt capable pin.
/// On many Arduino boards, there are limitations as to which pins may be used as interrupts.
/// On Leonardo pins 0, 1, 2 or 3. On Mega2560 pins 2, 3, 18, 19, 20, 21. On Due and Teensy, any digital pin.
/// On other Arduinos pins 2 or 3.
/// See http://arduino.cc/en/Reference/attachInterrupt for more details.
/// On Chipkit Uno32, pins 38, 2, 7, 8, 35.
/// On other boards, any digital pin may be used.
/// \param[in] spi Pointer to the SPI interface object to use.
/// Defaults to the standard Arduino hardware SPI interface
RH_RF95(PINS slaveSelectPin, PINS interruptPin, RHGenericSPI& spi = hardware_spi);
/// Initialise the Driver transport hardware and software.
/// Make sure the Driver is properly configured before calling init().
/// \return true if initialisation succeeded.
virtual bool init();
/// Prints the value of all chip registers
/// to the Serial device if RH_HAVE_SERIAL is defined for the current platform
/// For debugging purposes only.
/// \return true on success
bool printRegisters();
/// Sets all the registered required to configure the data modem in the RF95/96/97/98, including the bandwidth,
/// spreading factor etc. You can use this to configure the modem with custom configurations if none of the
/// canned configurations in ModemConfigChoice suit you.
/// \param[in] config A ModemConfig structure containing values for the modem configuration registers.
void setModemRegisters(const ModemConfig* config);
/// Select one of the predefined modem configurations. If you need a modem configuration not provided
/// here, use setModemRegisters() with your own ModemConfig.
/// \param[in] index The configuration choice.
/// \return true if index is a valid choice.
bool setModemConfig(ModemConfigChoice index);
/// Tests whether a new message is available
/// from the Driver.
/// On most drivers, this will also put the Driver into RHModeRx mode until
/// a message is actually received by the transport, when it wil be returned to RHModeIdle.
/// This can be called multiple times in a timeout loop
/// \return true if a new, complete, error-free uncollected message is available to be retreived by recv()
virtual bool available();
/// Turns the receiver on if it not already on.
/// If there is a valid message available, copy it to buf and return true
/// else return false.
/// If a message is copied, *len is set to the length (Caution, 0 length messages are permitted).
/// You should be sure to call this function frequently enough to not miss any messages
/// It is recommended that you call it in your main loop.
/// \param[in] buf Location to copy the received message
/// \param[in,out] len Pointer to available space in buf. Set to the actual number of octets copied.
/// \return true if a valid message was copied to buf
virtual bool recv(uint8_t* buf, uint8_t* len);
/// Waits until any previous transmit packet is finished being transmitted with waitPacketSent().
/// Then loads a message into the transmitter and starts the transmitter. Note that a message length
/// of 0 is permitted.
/// \param[in] data Array of data to be sent
/// \param[in] len Number of bytes of data to send
/// \return true if the message length was valid and it was correctly queued for transmit
virtual bool send(const uint8_t* data, uint8_t len);
/// Sets the length of the preamble
/// in bytes.
/// Caution: this should be set to the same
/// value on all nodes in your network. Default is 8.
/// Sets the message preamble length in RH_RF95_REG_??_PREAMBLE_?SB
/// \param[in] bytes Preamble length in bytes.
void setPreambleLength(uint16_t bytes);
/// Returns the maximum message length
/// available in this Driver.
/// \return The maximum legal message length
virtual uint8_t maxMessageLength();
/// Sets the transmitter and receiver
/// centre frequency
/// \param[in] centre Frequency in MHz. 137.0 to 1020.0. Caution: RFM95/96/97/98 comes in several
/// different frequency ranges, and setting a frequency outside that range of your radio will probably not work
/// \return true if the selected frquency centre is within range
bool setFrequency(float centre);
/// If current mode is Rx or Tx changes it to Idle. If the transmitter or receiver is running,
/// disables them.
void setModeIdle();
/// If current mode is Tx or Idle, changes it to Rx.
/// Starts the receiver in the RF95/96/97/98.
void setModeRx();
/// If current mode is Rx or Idle, changes it to Rx. F
/// Starts the transmitter in the RF95/96/97/98.
void setModeTx();
/// Sets the transmitter power output level.
/// Be a good neighbour and set the lowest power level you need.
/// Caution: legal power limits may apply in certain countries. At powers above 20dBm, PA_DAC is enabled.
/// After init(), the power will be set to 13dBm.
/// \param[in] power Transmitter power level in dBm. For RFM95/96/97/98 LORA, valid values are from +5 to +23
void setTxPower(int8_t power);
/// Sets the radio into low-power sleep mode.
/// If successful, the transport will stay in sleep mode until woken by
/// changing mode it idle, transmit or receive (eg by calling send(), recv(), available() etc)
/// Caution: there is a time penalty as the radio takes a finite time to wake from sleep mode.
/// \return true if sleep mode was successfully entered.
virtual bool sleep();
protected:
/// This is a low level function to handle the interrupts for one instance of RH_RF95.
/// Called automatically by isr*()
/// Should not need to be called by user code.
void handleInterrupt();
/// Examine the revceive buffer to determine whether the message is for this node
void validateRxBuf();
/// Clear our local receive buffer
void clearRxBuf();
private:
/// Low level interrupt service routine for device connected to interrupt 0
static void isr0();
/// Low level interrupt service routine for device connected to interrupt 1
static void isr1();
/// Low level interrupt service routine for device connected to interrupt 1
static void isr2();
/// Array of instances connected to interrupts 0 and 1
static RH_RF95* _deviceForInterrupt[];
/// Index of next interrupt number to use in _deviceForInterrupt
static uint8_t _interruptCount;
#if (RH_PLATFORM == RH_PLATFORM_MBED)
/// The configured interrupt pin connected to this instance
InterruptIn _interruptPin;
#else
/// The configured interrupt pin connected to this instance
uint8_t _interruptPin;
#endif
/// The index into _deviceForInterrupt[] for this device (if an interrupt is already allocated)
/// else 0xff
uint8_t _myInterruptIndex;
/// Number of octets in the buffer
volatile uint8_t _bufLen;
/// The receiver/transmitter buffer
uint8_t _buf[RH_RF95_MAX_PAYLOAD_LEN];
/// True when there is a valid message in the buffer
volatile bool _rxBufValid;
};
/// @example rf95_client.pde
/// @example rf95_server.pde
/// @example rf95_reliable_datagram_client.pde
/// @example rf95_reliable_datagram_server.pde
#endif