mbed API for Raspberry Pi boards.
mbedPi
This is an attempt to implement a limited number of mbed APIs for Raspberry Pi single-board computers. The project was inspired by and based on the arduPi library developed for the Arduino by Cooking Hacks .
Specifications
- Chip: Broadcom BCM2836 SoC
- Core architecture: Quad-core ARM Cortex-A7
- CPU frequency: 900 MHz
- GPU: Dual Core VideoCore IV® Multimedia Co-Processor
- Memory: 1GB LPDDR2
- Operating System: Boots from Micro SD card, running a version of the Linux operating system
- Power: Micro USB socket 5V, 2A
Connectors
- Ethernet: 10/100 BaseT Ethernet socket
- Video Output: HDMI (rev 1.3 & 1.4)
- Audio Output: 3.5mm jack, HDMI
- USB: 4 x USB 2.0 Connector
- GPIO Connector: 40-pin 2.54 mm (100 mil) expansion header: 2x20 strip providing 27 GPIO pins as well as +3.3 V, +5 V and GND supply lines
- Camera Connector: 15-pin MIPI Camera Serial Interface (CSI-2)
- JTAG: Not populated
- Display Connector: Display Serial Interface (DSI) 15 way flat flex cable connector with two data lanes and a clock lane
- Memory Card Slot: Micro SDIO
GPIO connector pinout
Information
Only the labels printed in blue/white or green/white (i.e. p3, gpio2 ...) must be used in your code. The other labels are given as information (alternate-functions, power pins, ...).
Building programs for the Raspberry Pi with mbedPi
I use Qt Creator for development, however you can use any other IDE available on the Raspberry Pi (e.g. Geany) if you like. For a quick try:
- Install Qt and the Qt Creator onto your Raspberry Pi. Then create a new "Blinky" Plain non-Qt C++ Project as follows:
- Change the main code as below:
main.cpp
#include "mbedPi.h" int main() { DigitalOut myled(p7); while(1) { myled = 1; // LED is ON wait(0.2); // 200 ms myled = 0; // LED is OFF wait(1.0); // 1 sec printf("Blink\r\n"); } }
- Copy the mbedPi.zip file into your project's folder and unzip.
- Add the mbedPi.h and mbedPi.cpp files to your project by right clicking on the "Blinky" project and then clicking on the "Add Existing Files..." option in the local menu:
- Double click on Blinky.pro to open it for editing and add new libraries by inserting a new line as follows:
- Compile the project.
- Connect an LED through a 1k resistor to pin 7 and the ground on the Raspberry Pi GPIO connector.
- Run the binary as sudo (sudo ./Blinky) and you should see the LED blinking.
- Press Ctrl+c to stop running the application.
source/wait.cpp@2:131555dc6fb7, 21 months ago (annotated)
- Committer:
- hudakz
- Date:
- Tue Dec 20 12:16:18 2022 +0000
- Revision:
- 2:131555dc6fb7
- Parent:
- 1:1f2d9982fa8c
Mbed API for Raspberry Pi boards equipped with BCM2836 SoC.
Who changed what in which revision?
User | Revision | Line number | New contents of line |
---|---|---|---|
hudakz | 1:1f2d9982fa8c | 1 | #include "wait.h" |
hudakz | 1:1f2d9982fa8c | 2 | |
hudakz | 1:1f2d9982fa8c | 3 | /** |
hudakz | 1:1f2d9982fa8c | 4 | * @brief |
hudakz | 1:1f2d9982fa8c | 5 | * @note |
hudakz | 1:1f2d9982fa8c | 6 | * @param |
hudakz | 1:1f2d9982fa8c | 7 | * @retval |
hudakz | 1:1f2d9982fa8c | 8 | */ |
hudakz | 1:1f2d9982fa8c | 9 | void wait(float s) |
hudakz | 1:1f2d9982fa8c | 10 | { |
hudakz | 1:1f2d9982fa8c | 11 | unistd::usleep(s * 1000 * 1000); |
hudakz | 1:1f2d9982fa8c | 12 | } |
hudakz | 1:1f2d9982fa8c | 13 | |
hudakz | 1:1f2d9982fa8c | 14 | /** |
hudakz | 1:1f2d9982fa8c | 15 | * @brief |
hudakz | 1:1f2d9982fa8c | 16 | * @note |
hudakz | 1:1f2d9982fa8c | 17 | * @param |
hudakz | 1:1f2d9982fa8c | 18 | * @retval |
hudakz | 1:1f2d9982fa8c | 19 | */ |
hudakz | 1:1f2d9982fa8c | 20 | void wait_ms(int ms) |
hudakz | 1:1f2d9982fa8c | 21 | { |
hudakz | 1:1f2d9982fa8c | 22 | unistd::usleep(ms * 1000); |
hudakz | 1:1f2d9982fa8c | 23 | } |
hudakz | 1:1f2d9982fa8c | 24 | |
hudakz | 1:1f2d9982fa8c | 25 | /** |
hudakz | 1:1f2d9982fa8c | 26 | * @brief |
hudakz | 1:1f2d9982fa8c | 27 | * @note |
hudakz | 1:1f2d9982fa8c | 28 | * @param |
hudakz | 1:1f2d9982fa8c | 29 | * @retval |
hudakz | 1:1f2d9982fa8c | 30 | */ |
hudakz | 1:1f2d9982fa8c | 31 | void wait_us(int us) |
hudakz | 1:1f2d9982fa8c | 32 | { |
hudakz | 1:1f2d9982fa8c | 33 | if (us > 100) { |
hudakz | 1:1f2d9982fa8c | 34 | struct timespec tim, tim2; |
hudakz | 1:1f2d9982fa8c | 35 | tim.tv_sec = 0; |
hudakz | 1:1f2d9982fa8c | 36 | tim.tv_nsec = us * 1000; |
hudakz | 1:1f2d9982fa8c | 37 | |
hudakz | 1:1f2d9982fa8c | 38 | if (nanosleep(&tim, &tim2) < 0) { |
hudakz | 1:1f2d9982fa8c | 39 | fprintf(stderr, "Nano sleep system call failed \n"); |
hudakz | 1:1f2d9982fa8c | 40 | exit(1); |
hudakz | 1:1f2d9982fa8c | 41 | } |
hudakz | 1:1f2d9982fa8c | 42 | } |
hudakz | 1:1f2d9982fa8c | 43 | else { |
hudakz | 1:1f2d9982fa8c | 44 | struct timeval tNow, tLong, tEnd; |
hudakz | 1:1f2d9982fa8c | 45 | |
hudakz | 1:1f2d9982fa8c | 46 | gettimeofday(&tNow, NULL); |
hudakz | 1:1f2d9982fa8c | 47 | tLong.tv_sec = us / 1000000; |
hudakz | 1:1f2d9982fa8c | 48 | tLong.tv_usec = us % 1000000; |
hudakz | 1:1f2d9982fa8c | 49 | timeradd(&tNow, &tLong, &tEnd); |
hudakz | 1:1f2d9982fa8c | 50 | |
hudakz | 1:1f2d9982fa8c | 51 | while (timercmp(&tNow, &tEnd, < )) |
hudakz | 1:1f2d9982fa8c | 52 | gettimeofday(&tNow, NULL); |
hudakz | 1:1f2d9982fa8c | 53 | } |
hudakz | 1:1f2d9982fa8c | 54 | } |
hudakz | 1:1f2d9982fa8c | 55 | |
hudakz | 1:1f2d9982fa8c | 56 | /** |
hudakz | 1:1f2d9982fa8c | 57 | * @brief |
hudakz | 1:1f2d9982fa8c | 58 | * @note |
hudakz | 1:1f2d9982fa8c | 59 | * @param |
hudakz | 1:1f2d9982fa8c | 60 | * @retval |
hudakz | 1:1f2d9982fa8c | 61 | */ |
hudakz | 1:1f2d9982fa8c | 62 | uint64_t millis() |
hudakz | 1:1f2d9982fa8c | 63 | { |
hudakz | 1:1f2d9982fa8c | 64 | return bcm2835_systimer_read() / 1000; |
hudakz | 1:1f2d9982fa8c | 65 | } |
hudakz | 1:1f2d9982fa8c | 66 | |
hudakz | 1:1f2d9982fa8c | 67 | /** |
hudakz | 1:1f2d9982fa8c | 68 | * @brief |
hudakz | 1:1f2d9982fa8c | 69 | * @note |
hudakz | 1:1f2d9982fa8c | 70 | * @param |
hudakz | 1:1f2d9982fa8c | 71 | * @retval |
hudakz | 1:1f2d9982fa8c | 72 | */ |
hudakz | 1:1f2d9982fa8c | 73 | void bcm2835_delay(unsigned int millis) |
hudakz | 1:1f2d9982fa8c | 74 | { |
hudakz | 1:1f2d9982fa8c | 75 | struct timespec sleeper; |
hudakz | 1:1f2d9982fa8c | 76 | |
hudakz | 1:1f2d9982fa8c | 77 | sleeper.tv_sec = (time_t) (millis / 1000); |
hudakz | 1:1f2d9982fa8c | 78 | sleeper.tv_nsec = (long)(millis % 1000) * 1000000; |
hudakz | 1:1f2d9982fa8c | 79 | nanosleep(&sleeper, NULL); |
hudakz | 1:1f2d9982fa8c | 80 | } |