Henrique Rosa
/
ILI9341_01_PAR8_Teste_V3
Testanto funções Display
MCUFRIEND_kbv/utility/mcufriend_shield.h
- Committer:
- henriquer
- Date:
- 2021-04-27
- Revision:
- 4:2d8f54d22dbd
- Parent:
- 1:a5ccd53612ea
File content as of revision 4:2d8f54d22dbd:
//#define USE_SPECIAL //check for custom drivers #define WR_ACTIVE2 {WR_ACTIVE; WR_ACTIVE;} #define WR_ACTIVE4 {WR_ACTIVE2; WR_ACTIVE2;} #define WR_ACTIVE8 {WR_ACTIVE4; WR_ACTIVE4;} #define RD_ACTIVE2 {RD_ACTIVE; RD_ACTIVE;} #define RD_ACTIVE4 {RD_ACTIVE2; RD_ACTIVE2;} #define RD_ACTIVE8 {RD_ACTIVE4; RD_ACTIVE4;} #define RD_ACTIVE16 {RD_ACTIVE8; RD_ACTIVE8;} #define WR_IDLE2 {WR_IDLE; WR_IDLE;} #define WR_IDLE4 {WR_IDLE2; WR_IDLE2;} #define RD_IDLE2 {RD_IDLE; RD_IDLE;} #define RD_IDLE4 {RD_IDLE2; RD_IDLE2;} #if defined(USE_SPECIAL) #include "mcufriend_special.h" #if !defined(USE_SPECIAL_FAIL) #warning WE ARE USING A SPECIAL CUSTOM DRIVER #endif #endif #if !defined(USE_SPECIAL) || defined (USE_SPECIAL_FAIL) #if 0 //################################### UNO ############################## #elif defined(__AVR_ATmega328P__) || defined(__AVR_ATmega328PB__) //regular UNO shield on UNO #define RD_PORT PORTC #define RD_PIN 0 #define WR_PORT PORTC #define WR_PIN 1 #define CD_PORT PORTC #define CD_PIN 2 #define CS_PORT PORTC #define CS_PIN 3 #define RESET_PORT PORTC #define RESET_PIN 4 #define BMASK 0x03 //more intuitive style for mixed Ports #define DMASK 0xFC //does exactly the same as previous #define write_8(x) { PORTB = (PORTB & ~BMASK) | ((x) & BMASK); PORTD = (PORTD & ~DMASK) | ((x) & DMASK); } #define read_8() ( (PINB & BMASK) | (PIND & DMASK) ) #define setWriteDir() { DDRB |= BMASK; DDRD |= DMASK; } #define setReadDir() { DDRB &= ~BMASK; DDRD &= ~DMASK; } #define write8(x) { write_8(x); WR_STROBE; } #define write16(x) { uint8_t h = (x)>>8, l = x; write8(h); write8(l); } #define READ_8(dst) { RD_STROBE; dst = read_8(); RD_IDLE; } #define READ_16(dst) { uint8_t hi; READ_8(hi); READ_8(dst); dst |= (hi << 8); } #define PIN_LOW(p, b) (p) &= ~(1<<(b)) #define PIN_HIGH(p, b) (p) |= (1<<(b)) #define PIN_OUTPUT(p, b) *(&p-1) |= (1<<(b)) //################################### MEGA2560 ############################## #elif defined(__AVR_ATmega2560__) || defined(__AVR_ATmega1280__) //regular UNO shield on MEGA2560 #define RD_PORT PORTF #define RD_PIN 0 #define WR_PORT PORTF #define WR_PIN 1 #define CD_PORT PORTF #define CD_PIN 2 #define CS_PORT PORTF #define CS_PIN 3 #define RESET_PORT PORTF #define RESET_PIN 4 #define EMASK 0x38 #define GMASK 0x20 #define HMASK 0x78 #define write_8(x) { PORTH &= ~HMASK; PORTG &= ~GMASK; PORTE &= ~EMASK; \ PORTH |= (((x) & (3<<0)) << 5); \ PORTE |= (((x) & (3<<2)) << 2); \ PORTG |= (((x) & (1<<4)) << 1); \ PORTE |= (((x) & (1<<5)) >> 2); \ PORTH |= (((x) & (3<<6)) >> 3); \ } #define read_8() ( ((PINH & (3<<5)) >> 5)\ | ((PINE & (3<<4)) >> 2)\ | ((PING & (1<<5)) >> 1)\ | ((PINE & (1<<3)) << 2)\ | ((PINH & (3<<3)) << 3)\ ) #define setWriteDir() { DDRH |= HMASK; DDRG |= GMASK; DDRE |= EMASK; } #define setReadDir() { DDRH &= ~HMASK; DDRG &= ~GMASK; DDRE &= ~EMASK; } #define write8(x) { write_8(x); WR_STROBE; } #define write16(x) { uint8_t h = (x)>>8, l = x; write8(h); write8(l); } #define READ_8(dst) { RD_STROBE; dst = read_8(); RD_IDLE; } #define READ_16(dst) { uint8_t hi; READ_8(hi); READ_8(dst); dst |= (hi << 8); } #define PIN_LOW(p, b) (p) &= ~(1<<(b)) #define PIN_HIGH(p, b) (p) |= (1<<(b)) #define PIN_OUTPUT(p, b) *(&p-1) |= (1<<(b)) //################################### MEGA4809 NANO_EVERY 4808 ############################## #elif defined(__AVR_ATmega4808__) // Thinary EVERY-4808 with Nano-Shield_Adapter #warning EVERY-4808 with Nano-Shield_Adapter #define RD_PORT VPORTD // #define RD_PIN 0 #define WR_PORT VPORTD #define WR_PIN 1 #define CD_PORT VPORTD #define CD_PIN 2 #define CS_PORT VPORTD #define CS_PIN 3 #define RESET_PORT VPORTF #define RESET_PIN 2 #define AMASK 0xFF #define write_8(x) { VPORTA.OUT = ((x) << 6) | ((x) >> 2); } #define read_8() ( (VPORTA.IN >> 6) | (VPORTA.IN << 2) ) #define setWriteDir() { VPORTA_DIR |= AMASK; } #define setReadDir() { VPORTA_DIR &= ~AMASK; } //#define WRITE_DELAY { WR_ACTIVE; WR_ACTIVE; } //6.47s no_inline #define WRITE_DELAY { WR_ACTIVE2; WR_ACTIVE; } //-Os=5.43s @20MHz always_inline. (-O1=5.41s, -O3=5.25s) #define READ_DELAY { RD_ACTIVE4; } //ID=0x7789 #define write8(x) { write_8(x); WRITE_DELAY; WR_STROBE; } #define write16(x) { uint8_t h = (x)>>8, l = x; write8(h); write8(l); } #define READ_8(dst) { RD_STROBE; READ_DELAY; dst = read_8(); RD_IDLE; } #define READ_16(dst) { uint8_t hi; READ_8(hi); READ_8(dst); dst |= (hi << 8); } #define PIN_LOW(p, b) (p).OUT &= ~(1<<(b)) #define PIN_HIGH(p, b) (p).OUT |= (1<<(b)) #define PIN_OUTPUT(p, b) (p).DIR |= (1<<(b)) //################################### MEGA4809 NANO_EVERY ############################## #elif defined(__AVR_ATmega4809__) && defined(ARDUINO_AVR_NANO_EVERY) // EVERY-4809 with Nano-Shield_Adapter #warning EVERY-4809 with Nano-Shield_Adapter using VPORT.OUT and BLD/BST #define RD_PORT VPORTD // #define RD_PIN 3 #define WR_PORT VPORTD #define WR_PIN 2 #define CD_PORT VPORTD #define CD_PIN 1 #define CS_PORT VPORTD #define CS_PIN 0 #define RESET_PORT VPORTF #define RESET_PIN 2 #define AMASK (3<<0) #define BMASK (5<<0) #define CMASK (1<<6) #define EMASK (1<<3) #define FMASK (3<<4) static __attribute((always_inline)) void write_8(uint8_t val) { asm volatile("in __tmp_reg__,0x01" "\n\t" //VPORTA.OUT "BST %0,2" "\n\t" "BLD __tmp_reg__,0" "\n\t" "BST %0,7" "\n\t" "BLD __tmp_reg__,1" "\n\t" "out 0x01,__tmp_reg__" : : "a" (val)); asm volatile("in __tmp_reg__,0x05" "\n\t" //VPORTB.OUT "BST %0,1" "\n\t" "BLD __tmp_reg__,0" "\n\t" "BST %0,5" "\n\t" "BLD __tmp_reg__,2" "\n\t" "out 0x05,__tmp_reg__" : : "a" (val)); asm volatile("in __tmp_reg__,0x09" "\n\t" //VPORTC.OUT "BST %0,4" "\n\t" "BLD __tmp_reg__,6" "\n\t" "out 0x09,__tmp_reg__" : : "a" (val)); asm volatile("in __tmp_reg__,0x11" "\n\t" //VPORTE.OUT "BST %0,0" "\n\t" "BLD __tmp_reg__,3" "\n\t" "out 0x11,__tmp_reg__" : : "a" (val)); asm volatile("in __tmp_reg__,0x15" "\n\t" //VPORTF.OUT "BST %0,3" "\n\t" "BLD __tmp_reg__,5" "\n\t" "BST %0,6" "\n\t" "BLD __tmp_reg__,4" "\n\t" "out 0x15,__tmp_reg__" : : "a" (val)); } #define read_8() ( 0 \ | ((VPORTA_IN & (1<<0)) << 2)\ | ((VPORTA_IN & (1<<1)) << 6)\ | ((VPORTB_IN & (1<<0)) << 1)\ | ((VPORTB_IN & (1<<2)) << 3)\ | ((VPORTC_IN & CMASK) >> 2)\ | ((VPORTE_IN & EMASK) >> 3)\ | ((VPORTF_IN & (1<<5)) >> 2)\ | ((VPORTF_IN & (1<<4)) << 2)\ ) #define setWriteDir() { VPORTA_DIR |= AMASK; VPORTB_DIR |= BMASK; VPORTC_DIR |= CMASK; VPORTE_DIR |= EMASK; VPORTF_DIR |= FMASK; } #define setReadDir() { VPORTA_DIR &= ~AMASK; VPORTB_DIR &= ~BMASK; VPORTC_DIR &= ~CMASK; VPORTE_DIR &= ~EMASK; VPORTF_DIR &= ~FMASK; } //#define WRITE_DELAY { WR_ACTIVE; WR_ACTIVE; } //6.47s no_inline #define WRITE_DELAY { WR_ACTIVE2; WR_ACTIVE; } //-Os=5.43s @20MHz always_inline. (-O1=5.41s, -O3=5.25s) #define READ_DELAY { RD_ACTIVE4; } //ID=0x7789 #define write8(x) { write_8(x); WRITE_DELAY; WR_STROBE; } #define write16(x) { uint8_t h = (x)>>8, l = x; write8(h); write8(l); } #define READ_8(dst) { RD_STROBE; READ_DELAY; dst = read_8(); RD_IDLE; } #define READ_16(dst) { uint8_t hi; READ_8(hi); READ_8(dst); dst |= (hi << 8); } #define PIN_LOW(p, b) (p).OUT &= ~(1<<(b)) #define PIN_HIGH(p, b) (p).OUT |= (1<<(b)) #define PIN_OUTPUT(p, b) (p).DIR |= (1<<(b)) //################################### TEENSY++2.0 ############################## #elif defined(__AVR_AT90USB1286__) //regular UNO shield on TEENSY++ 2.0 thanks tysonlt //LCD pins |D7 |D6 |D5 |D4 |D3 |D2 |D1 |D0 | |RD |WR |RS |CS |RST| //AVR pin |PD7|PD6|PD5|PD4|PD3|PD2|PE1|PE0| |PF0|PF1|PF2|PF3|PF4| #define RD_PORT PORTF #define RD_PIN 0 #define WR_PORT PORTF #define WR_PIN 1 #define CD_PORT PORTF #define CD_PIN 2 #define CS_PORT PORTF #define CS_PIN 3 #define RESET_PORT PORTF #define RESET_PIN 4 #define EMASK 0x03 //more intuitive style for mixed Ports #define DMASK 0xFC //does exactly the same as previous #define write_8(x) { PORTE = (PORTE & ~EMASK) | ((x) & EMASK); PORTD = (PORTD & ~DMASK) | ((x) & DMASK); } #define read_8() ( (PINE & EMASK) | (PIND & DMASK) ) #define setWriteDir() { DDRE |= EMASK; DDRD |= DMASK; } #define setReadDir() { DDRE &= ~EMASK; DDRD &= ~DMASK; } #define write8(x) { write_8(x); WR_STROBE; } #define write16(x) { uint8_t h = (x)>>8, l = x; write8(h); write8(l); } #define READ_8(dst) { RD_STROBE; dst = read_8(); RD_IDLE; } #define READ_16(dst) { uint8_t hi; READ_8(hi); READ_8(dst); dst |= (hi << 8); } #define PIN_LOW(p, b) (p) &= ~(1<<(b)) #define PIN_HIGH(p, b) (p) |= (1<<(b)) #define PIN_OUTPUT(p, b) *(&p-1) |= (1<<(b)) //################################# ZERO and M0_PRO ############################ #elif defined(__SAMD21G18A__) //regular UNO shield on ZERO or M0_PRO #include "sam.h" // configure macros for the control pins #define RD_PORT PORT->Group[0] #define RD_PIN 2 #define WR_PORT PORT->Group[1] #define WR_PIN 8 #define CD_PORT PORT->Group[1] #define CD_PIN 9 #define CS_PORT PORT->Group[0] #define CS_PIN 4 #define RESET_PORT PORT->Group[0] #define RESET_PIN 5 // configure macros for data bus #define DMASK 0x0030C3C0 // #define write_8(x) PORT->Group[0].OUT.reg = (PORT->Group[0].OUT.reg & ~DMASK)|(((x) & 0x0F) << 6)|(((x) & 0x30) << 10)|(((x) & 0xC0)<<14) #if defined(ARDUINO_SAMD_ZERO) || defined(ARDUINO_SAMD_ZERO) // American ZERO #define write_8(x) {\ PORT->Group[0].OUTCLR.reg = DMASK;\ PORT->Group[0].OUTSET.reg = (((x) & 0x0B) << 6)\ |(((x) & (1<<2)) << 12)\ |(((x) & (1<<4)) << 4)\ |(((x) & (1<<5)) << 10)\ |(((x) & 0xC0) << 14);\ } #define read_8() (((PORT->Group[0].IN.reg >> 6) & 0x0B)\ |((PORT->Group[0].IN.reg >> 12) & (1<<2))\ |((PORT->Group[0].IN.reg >> 4) & (1<<4))\ |((PORT->Group[0].IN.reg >> 10) & (1<<5))\ |((PORT->Group[0].IN.reg >> 14) & 0xC0)) #else //default to an M0_PRO on v1.6.5 or 1.7.6 #define write_8(x) {\ PORT->Group[0].OUTCLR.reg = DMASK;\ PORT->Group[0].OUTSET.reg = (((x) & 0x0F) << 6)\ |(((x) & 0x30) << 10)\ |(((x) & 0xC0) << 14);\ } #define read_8() (((PORT->Group[0].IN.reg >> 6) & 0x0F)|((PORT->Group[0].IN.reg >> 10) & 0x30)|((PORT->Group[0].IN.reg >> 14) & 0xC0)) #endif #define setWriteDir() { PORT->Group[0].DIRSET.reg = DMASK; \ PORT->Group[0].WRCONFIG.reg = (DMASK & 0xFFFF) | (0<<22) | (1<<28) | (1<<30); \ PORT->Group[0].WRCONFIG.reg = (DMASK>>16) | (0<<22) | (1<<28) | (1<<30) | (1<<31); \ } #define setReadDir() { PORT->Group[0].DIRCLR.reg = DMASK; \ PORT->Group[0].WRCONFIG.reg = (DMASK & 0xFFFF) | (1<<17) | (1<<28) | (1<<30); \ PORT->Group[0].WRCONFIG.reg = (DMASK>>16) | (1<<17) | (1<<28) | (1<<30) | (1<<31); \ } #define write8(x) { write_8(x); WR_ACTIVE; WR_STROBE; } #define write16(x) { uint8_t h = (x)>>8, l = x; write8(h); write8(l); } #define READ_8(dst) { RD_STROBE; dst = read_8(); RD_IDLE; } #define READ_16(dst) { uint8_t hi; READ_8(hi); READ_8(dst); dst |= (hi << 8); } // Shield Control macros. #define PIN_LOW(port, pin) (port).OUTCLR.reg = (1<<(pin)) #define PIN_HIGH(port, pin) (port).OUTSET.reg = (1<<(pin)) #define PIN_OUTPUT(port, pin) (port).DIR.reg |= (1<<(pin)) //####################################### DUE ############################ #elif defined(__SAM3X8E__) //regular UNO shield on DUE #define WRITE_DELAY { WR_ACTIVE; } #define IDLE_DELAY { WR_IDLE; } #define READ_DELAY { RD_ACTIVE;} // configure macros for the control pins #define RD_PORT PIOA #define RD_PIN 16 #define WR_PORT PIOA #define WR_PIN 24 #define CD_PORT PIOA #define CD_PIN 23 #define CS_PORT PIOA #define CS_PIN 22 #define RESET_PORT PIOA #define RESET_PIN 6 // configure macros for data bus #define BMASK (1<<25) #define CMASK (0xBF << 21) #define write_8(x) { PIOB->PIO_CODR = BMASK; PIOC->PIO_CODR = CMASK; \ PIOB->PIO_SODR = (((x) & (1<<2)) << 23); \ PIOC->PIO_SODR = (((x) & (1<<0)) << 22) \ | (((x) & (1<<1)) << 20) \ | (((x) & (1<<3)) << 25) \ | (((x) & (1<<4)) << 22) \ | (((x) & (1<<5)) << 20) \ | (((x) & (1<<6)) << 18) \ | (((x) & (1<<7)) << 16); \ } #define read_8() ( ((PIOC->PIO_PDSR & (1<<22)) >> 22)\ | ((PIOC->PIO_PDSR & (1<<21)) >> 20)\ | ((PIOB->PIO_PDSR & (1<<25)) >> 23)\ | ((PIOC->PIO_PDSR & (1<<28)) >> 25)\ | ((PIOC->PIO_PDSR & (1<<26)) >> 22)\ | ((PIOC->PIO_PDSR & (1<<25)) >> 20)\ | ((PIOC->PIO_PDSR & (1<<24)) >> 18)\ | ((PIOC->PIO_PDSR & (1<<23)) >> 16)\ ) #define setWriteDir() { PIOB->PIO_OER = BMASK; PIOC->PIO_OER = CMASK; } #define setReadDir() { \ PMC->PMC_PCER0 = (1 << ID_PIOB)|(1 << ID_PIOC);\ PIOB->PIO_ODR = BMASK; PIOC->PIO_ODR = CMASK;\ } #define write8(x) { write_8(x); WRITE_DELAY; WR_STROBE; IDLE_DELAY; } #define write16(x) { uint8_t h = (x)>>8, l = x; write8(h); write8(l); } #define READ_8(dst) { RD_STROBE; READ_DELAY; dst = read_8(); RD_IDLE; RD_IDLE; } #define READ_16(dst) { uint8_t hi; READ_8(hi); READ_8(dst); dst |= (hi << 8); } // Shield Control macros. #define PIN_LOW(port, pin) (port)->PIO_CODR = (1<<(pin)) #define PIN_HIGH(port, pin) (port)->PIO_SODR = (1<<(pin)) #define PIN_OUTPUT(port, pin) (port)->PIO_OER = (1<<(pin)) //################################### LEONARDO ############################## #elif defined(__AVR_ATmega32U4__) //regular UNO shield on Leonardo #define RD_PORT PORTF #define RD_PIN 7 #define WR_PORT PORTF #define WR_PIN 6 #define CD_PORT PORTF #define CD_PIN 5 #define CS_PORT PORTF #define CS_PIN 4 #define RESET_PORT PORTF #define RESET_PIN 1 #define BMASK (3<<4) #define CMASK (1<<6) #define DMASK ((1<<7)|(1<<4)|(3<<0)) #define EMASK (1<<6) static inline //hope we use r24 void write_8(uint8_t x) { PORTB &= ~BMASK; PORTC &= ~CMASK; PORTD &= ~DMASK; PORTE &= ~EMASK; PORTB |= (((x) & (3 << 0)) << 4); PORTD |= (((x) & (1 << 2)) >> 1); PORTD |= (((x) & (1 << 3)) >> 3); PORTD |= (((x) & (1 << 4)) << 0); PORTC |= (((x) & (1 << 5)) << 1); PORTD |= (((x) & (1 << 6)) << 1); PORTE |= (((x) & (1 << 7)) >> 1); } #define read_8() ( ((PINB & (3<<4)) >> 4)\ | ((PIND & (1<<1)) << 1)\ | ((PIND & (1<<0)) << 3)\ | ((PIND & (1<<4)) >> 0)\ | ((PINC & (1<<6)) >> 1)\ | ((PIND & (1<<7)) >> 1)\ | ((PINE & (1<<6)) << 1)\ ) #define setWriteDir() { DDRB |= BMASK; DDRC |= CMASK; DDRD |= DMASK; DDRE |= EMASK; } #define setReadDir() { DDRB &= ~BMASK; DDRC &= ~CMASK; DDRD &= ~DMASK; DDRE &= ~EMASK; } #define write8(x) { write_8(x); WR_STROBE; } #define write16(x) { uint8_t h = (x)>>8, l = x; write8(h); write8(l); } #define READ_8(dst) { RD_STROBE; dst = read_8(); RD_IDLE; } #define READ_16(dst) { uint8_t hi; READ_8(hi); READ_8(dst); dst |= (hi << 8); } #define PIN_LOW(p, b) (p) &= ~(1<<(b)) #define PIN_HIGH(p, b) (p) |= (1<<(b)) #define PIN_OUTPUT(p, b) *(&p-1) |= (1<<(b)) //################################### UNO SHIELD on BOBUINO ############################## #elif defined(__AVR_ATmega1284P__) || defined(__AVR_ATmega644P__) //UNO shield on BOBUINO #warning regular UNO shield on BOBUINO //LCD pins |D7 |D6 |D5 |D4 |D3 |D2 |D1 |D0 | |RD |WR |RS |CS |RST| //AVR pin |PB3|PB2|PB1|PB0|PD3|PD2|PD6|PD5| |PA7|PA6|PA5|PA4|PA3| #define RD_PORT PORTA #define RD_PIN 7 #define WR_PORT PORTA #define WR_PIN 6 #define CD_PORT PORTA #define CD_PIN 5 #define CS_PORT PORTA #define CS_PIN 4 #define RESET_PORT PORTA #define RESET_PIN 3 #define BMASK 0x0F // #define DMASK 0x6C // #define write_8(x) { PORTB = (PORTB & ~BMASK) | ((x) >> 4); \ PORTD = (PORTD & ~DMASK) | ((x) & 0x0C) | (((x) & 0x03) << 5); } #define read_8() ( (PINB << 4) | (PIND & 0x0C) | ((PIND & 0x60) >> 5) ) #define setWriteDir() { DDRB |= BMASK; DDRD |= DMASK; } #define setReadDir() { DDRB &= ~BMASK; DDRD &= ~DMASK; } #define write8(x) { write_8(x); WR_STROBE; } #define write16(x) { uint8_t h = (x)>>8, l = x; write8(h); write8(l); } #define READ_8(dst) { RD_STROBE; dst = read_8(); RD_IDLE; } #define READ_16(dst) { uint8_t hi; READ_8(hi); READ_8(dst); dst |= (hi << 8); } #define PIN_LOW(p, b) (p) &= ~(1<<(b)) #define PIN_HIGH(p, b) (p) |= (1<<(b)) #define PIN_OUTPUT(p, b) *(&p-1) |= (1<<(b)) //####################################### TEENSY ############################ #elif defined(__MK20DX128__) || defined(__MK20DX256__) || defined(__MK64FX512__) || defined(__MK66FX1M0__) // regular UNO shield on a Teensy 3.x #warning regular UNO shield on a Teensy 3.x //LCD pins |D7 |D6 |D5 |D4 |D3 |D2 |D1 |D0 | |RD |WR |RS |CS |RST| //MK20 pin |PD2|PD4|PD7|PA13|PA12|PD2|PC3|PD3| |PD1|PC0|PB0|PB1|PB3| #if defined(__MK20DX128__) || defined(__MK20DX256__) // Teensy3.0 || 3.2 96MHz #define WRITE_DELAY { WR_ACTIVE2; } #define READ_DELAY { RD_ACTIVE8; RD_ACTIVE; } #elif defined(__MK64FX512__) // Teensy3.5 120MHz thanks to PeteJohno #define WRITE_DELAY { WR_ACTIVE4; } #define READ_DELAY { RD_ACTIVE8; } #elif defined(__MK66FX1M0__) // Teensy3.6 180MHz untested. delays can possibly be reduced. #define WRITE_DELAY { WR_ACTIVE8; } #define READ_DELAY { RD_ACTIVE16; } #else #error unspecified delays #endif #define RD_PORT GPIOD #define RD_PIN 1 #define WR_PORT GPIOC #define WR_PIN 0 #define CD_PORT GPIOB #define CD_PIN 0 #define CS_PORT GPIOB #define CS_PIN 1 #define RESET_PORT GPIOB #define RESET_PIN 3 // configure macros for the data pins #define AMASK ((1<<12)|(1<<13)) #define CMASK ((1<<3)) #define DMASK ((1<<0)|(1<<2)|(1<<3)|(1<<4)|(1<<7)) #define write_8(d) { \ GPIOA_PCOR = AMASK; GPIOC_PCOR = CMASK; GPIOD_PCOR = DMASK; \ GPIOA_PSOR = (((d) & (1 << 3)) << 9) \ | (((d) & (1 << 4)) << 9); \ GPIOC_PSOR = (((d) & (1 << 1)) << 2); \ GPIOD_PSOR = (((d) & (1 << 0)) << 3) \ | (((d) & (1 << 2)) >> 2) \ | (((d) & (1 << 5)) << 2) \ | (((d) & (1 << 6)) >> 2) \ | (((d) & (1 << 7)) >> 5); \ } #define read_8() ((((GPIOD_PDIR & (1<<3)) >> 3) \ | ((GPIOC_PDIR & (1 << 3)) >> 2) \ | ((GPIOD_PDIR & (1 << 0)) << 2) \ | ((GPIOA_PDIR & (1 << 12)) >> 9) \ | ((GPIOA_PDIR & (1 << 13)) >> 9) \ | ((GPIOD_PDIR & (1 << 7)) >> 2) \ | ((GPIOD_PDIR & (1 << 4)) << 2) \ | ((GPIOD_PDIR & (1 << 2)) << 5))) #define setWriteDir() {GPIOA_PDDR |= AMASK;GPIOC_PDDR |= CMASK;GPIOD_PDDR |= DMASK; } #define setReadDir() {GPIOA_PDDR &= ~AMASK;GPIOC_PDDR &= ~CMASK;GPIOD_PDDR &= ~DMASK; } #define write8(x) { write_8(x); WRITE_DELAY; WR_STROBE; } //PJ adjusted #define write16(x) { uint8_t h = (x)>>8, l = x; write8(h); write8(l); } #define READ_8(dst) { RD_STROBE; READ_DELAY; dst = read_8(); RD_IDLE; } //PJ adjusted #define READ_16(dst) { uint8_t hi; READ_8(hi); READ_8(dst); dst |= (hi << 8); } //#define GPIO_INIT() {SIM_SCGC5 |= 0x3E00;} //PORTA-PORTE #define GPIO_INIT() {for (int i = 2; i <= 9; i++) pinMode(i, OUTPUT); for (int i = A0; i <= A4; i++) pinMode(i, OUTPUT);} #define PASTE(x, y) x ## y #define PIN_LOW(port, pin) PASTE(port, _PCOR) = (1<<(pin)) #define PIN_HIGH(port, pin) PASTE(port, _PSOR) = (1<<(pin)) #define PIN_OUTPUT(port, pin) PASTE(port, _PDDR) |= (1<<(pin)) //####################################### STM32 ############################ // NUCLEO: ARDUINO_NUCLEO_xxxx from ST Core or ARDUINO_STM_NUCLEO_F103RB from MapleCore // BLUEPILL: ARDUINO_NUCLEO_F103C8 / ARDUINO_BLUEPILL_F103C8 from ST Core or ARDUINO_GENERIC_STM32F103C from MapleCore // MAPLE_REV3: n/a from ST Core or ARDUINO_MAPLE_REV3 from MapleCore // ST Core: ARDUINO_ARCH_STM32 // MapleCore: __STM32F1__ #elif defined(__STM32F1__) || defined(ARDUINO_ARCH_STM32) //MapleCore or ST Core #define IS_NUCLEO64 ( defined(ARDUINO_STM_NUCLEO_F103RB) \ || defined(ARDUINO_NUCLEO_F030R8) || defined(ARDUINO_NUCLEO_F091RC) \ || defined(ARDUINO_NUCLEO_F103RB) || defined(ARDUINO_NUCLEO_F303RE) \ || defined(ARDUINO_NUCLEO_F401RE) || defined(ARDUINO_NUCLEO_F411RE) \ || defined(ARDUINO_NUCLEO_F446RE) || defined(ARDUINO_NUCLEO_L053R8) \ || defined(ARDUINO_NUCLEO_L152RE) || defined(ARDUINO_NUCLEO_L476RG) \ || defined(ARDUINO_NUCLEO_F072RB) \ ) #define IS_NUCLEO144 ( defined(ARDUINO_NUCLEO_F207ZG) \ || defined(ARDUINO_NUCLEO_F429ZI) || defined(ARDUINO_NUCLEO_F767ZI) \ || defined(ARDUINO_NUCLEO_L496ZG) || defined(ARDUINO_NUCLEO_L496ZG_P) \ || defined(ARDUINO_NUCLEO_H743ZI) \ ) // F1xx, F4xx, L4xx have different registers and styles. General Macros #if defined(__STM32F1__) //weird Maple Core #define REGS(x) regs->x #else //regular ST Core #define REGS(x) x #endif #define PIN_HIGH(port, pin) (port)-> REGS(BSRR) = (1<<(pin)) #define PIN_LOW(port, pin) (port)-> REGS(BSRR) = (1<<((pin)+16)) #define PIN_MODE2(reg, pin, mode) reg=(reg&~(0x3<<((pin)<<1)))|(mode<<((pin)<<1)) #define GROUP_MODE(port, reg, mask, val) {port->REGS(reg) = (port->REGS(reg) & ~(mask)) | ((mask)&(val)); } // Family specific Macros. F103 needs ST and Maple compatibility // note that ILI9320 class of controller has much slower Read cycles #if 0 #elif defined(__STM32F1__) || defined(ARDUINO_NUCLEO_F103C8) || defined(ARDUINO_BLUEPILL_F103C8) || defined(ARDUINO_NUCLEO_F103RB) #define WRITE_DELAY { } #define READ_DELAY { RD_ACTIVE; } #if defined(__STM32F1__) //MapleCore crts.o does RCC. not understand regular syntax anyway #define GPIO_INIT() #else #define GPIO_INIT() { RCC->APB2ENR |= RCC_APB2ENR_IOPAEN | RCC_APB2ENR_IOPBEN | RCC_APB2ENR_IOPCEN | RCC_APB2ENR_IOPDEN | RCC_APB2ENR_AFIOEN; \ AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_1;} #endif #define GP_OUT(port, reg, mask) GROUP_MODE(port, reg, mask, 0x33333333) #define GP_INP(port, reg, mask) GROUP_MODE(port, reg, mask, 0x44444444) #define PIN_OUTPUT(port, pin) {\ if (pin < 8) {GP_OUT(port, CRL, 0xF<<((pin)<<2));} \ else {GP_OUT(port, CRH, 0xF<<((pin&7)<<2));} \ } #define PIN_INPUT(port, pin) { \ if (pin < 8) { GP_INP(port, CRL, 0xF<<((pin)<<2)); } \ else { GP_INP(port, CRH, 0xF<<((pin&7)<<2)); } \ } // should be easy to add F030, F091, F303, L053, ... #elif defined(STM32F030x8) #define WRITE_DELAY { } #define READ_DELAY { RD_ACTIVE; } #define GPIO_INIT() { RCC->AHBENR |= RCC_AHBENR_GPIOAEN | RCC_AHBENR_GPIOBEN | RCC_AHBENR_GPIOCEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32F072xB) #define WRITE_DELAY { } #define READ_DELAY { RD_ACTIVE; } #define GPIO_INIT() { RCC->AHBENR |= RCC_AHBENR_GPIOAEN | RCC_AHBENR_GPIOBEN | RCC_AHBENR_GPIOCEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32F091xC) #define WRITE_DELAY { } #define READ_DELAY { RD_ACTIVE; } #define GPIO_INIT() { RCC->AHBENR |= RCC_AHBENR_GPIOAEN | RCC_AHBENR_GPIOBEN | RCC_AHBENR_GPIOCEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32F207xx) #warning DELAY macros untested yet #define WRITE_DELAY { WR_ACTIVE8; } //120MHz #define IDLE_DELAY { WR_IDLE2;WR_IDLE; } #define READ_DELAY { RD_ACTIVE16;} #define GPIO_INIT() { RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN | RCC_AHB1ENR_GPIOCEN | RCC_AHB1ENR_GPIODEN | RCC_AHB1ENR_GPIOEEN | RCC_AHB1ENR_GPIOFEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32F303xE) #define WRITE_DELAY { } #define READ_DELAY { RD_ACTIVE8; } //thanks MasterT #define GPIO_INIT() { RCC->AHBENR |= RCC_AHBENR_GPIOAEN | RCC_AHBENR_GPIOBEN | RCC_AHBENR_GPIOCEN; \ /* AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_1; */ } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) //thanks fpiSTM #elif defined(STM32F401xE) #define WRITE_DELAY { WR_ACTIVE2; } //84MHz #define READ_DELAY { RD_ACTIVE4; } #define GPIO_INIT() { RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN | RCC_AHB1ENR_GPIOBEN | RCC_AHB1ENR_GPIOCEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32F411xE) #define WRITE_DELAY { WR_ACTIVE2; WR_ACTIVE; } //100MHz #define READ_DELAY { RD_ACTIVE4; RD_ACTIVE2; } #define GPIO_INIT() { RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN | RCC_AHB1ENR_GPIOBEN | RCC_AHB1ENR_GPIOCEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32F429xx) #warning DELAY macros untested yet #define WRITE_DELAY { WR_ACTIVE8; } //180MHz #define IDLE_DELAY { WR_IDLE2;WR_IDLE; } #define READ_DELAY { RD_ACTIVE16;} #define GPIO_INIT() { RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN | RCC_AHB1ENR_GPIOCEN | RCC_AHB1ENR_GPIODEN | RCC_AHB1ENR_GPIOEEN | RCC_AHB1ENR_GPIOFEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32F446xx) #define WRITE_DELAY { WR_ACTIVE8; } //180MHz #define IDLE_DELAY { WR_IDLE2;WR_IDLE; } #define READ_DELAY { RD_ACTIVE16;} #define GPIO_INIT() { RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN | RCC_AHB1ENR_GPIOBEN | RCC_AHB1ENR_GPIOCEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32F767xx) #warning DELAY macros untested yet #define WRITE_DELAY { WR_ACTIVE8;WR_ACTIVE2; } //216MHz #define IDLE_DELAY { WR_IDLE2;WR_IDLE; } #define READ_DELAY { RD_ACTIVE16;RD_ACTIVE16;RD_ACTIVE4;} #define GPIO_INIT() { RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN | RCC_AHB1ENR_GPIOCEN | RCC_AHB1ENR_GPIODEN | RCC_AHB1ENR_GPIOEEN | RCC_AHB1ENR_GPIOFEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32H743xx) // thanks MagicianT #warning STM32H743xx< DELAY macros untested yet #define WRITE_DELAY { WR_ACTIVE8;WR_ACTIVE2; } //F_CPU=400MHz #define IDLE_DELAY { WR_IDLE2;WR_IDLE; } #define READ_DELAY { RD_ACTIVE16;RD_ACTIVE16;RD_ACTIVE4;} #define GPIO_INIT() { RCC->AHB4ENR |= RCC_AHB4ENR_GPIOAEN | RCC_AHB4ENR_GPIOCEN | RCC_AHB4ENR_GPIODEN | RCC_AHB4ENR_GPIOEEN | RCC_AHB4ENR_GPIOFEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32L053xx) #define WRITE_DELAY { } //32MHz M0+ #define READ_DELAY { RD_ACTIVE; } #define GPIO_INIT() { RCC->IOPENR |= RCC_IOPENR_GPIOAEN | RCC_IOPENR_GPIOBEN | RCC_IOPENR_GPIOCEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32L152xE) #define WRITE_DELAY { } //32MHz M3 #define READ_DELAY { RD_ACTIVE; } #define GPIO_INIT() { RCC->AHBENR |= RCC_AHBENR_GPIOAEN | RCC_AHBENR_GPIOBEN | RCC_AHBENR_GPIOCEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32L476xx) #define WRITE_DELAY { WR_ACTIVE2; } //80MHz #define READ_DELAY { RD_ACTIVE4; RD_ACTIVE; } #define GPIO_INIT() { RCC->AHB2ENR |= RCC_AHB2ENR_GPIOAEN | RCC_AHB2ENR_GPIOBEN | RCC_AHB2ENR_GPIOCEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #elif defined(STM32L496xx) #warning DELAY macros untested yet #define WRITE_DELAY { WR_ACTIVE2; } //80MHz #define READ_DELAY { RD_ACTIVE4; RD_ACTIVE; } #define GPIO_INIT() { RCC->AHB2ENR |= RCC_AHB2ENR_GPIOAEN | RCC_AHB2ENR_GPIOCEN | RCC_AHB2ENR_GPIODEN | RCC_AHB2ENR_GPIOEEN | RCC_AHB2ENR_GPIOFEN; } #define PIN_OUTPUT(port, pin) PIN_MODE2((port)->MODER, pin, 0x1) #else #error unsupported STM32 #endif #if 0 #elif defined(ARDUINO_GENERIC_STM32F103C) || defined(ARDUINO_NUCLEO_F103C8) || defined(ARDUINO_BLUEPILL_F103C8) #warning Uno Shield on BLUEPILL //LCD pins |D7 |D6 |D5 |D4 |D3 |D2 |D1 |D0 | |RD |WR |RS |CS |RST| |SD_SS|SD_DI|SD_DO|SD_SCK| //STM32 pin |PA7|PA6|PA5|PA4|PA3|PA2|PA1|PA0| |PB0|PB6|PB7|PB8|PB9| |PA15 |PB5 |PB4 |PB3 | **ALT-SPI1** #define RD_PORT GPIOB //#define RD_PIN 5 #define RD_PIN 0 //hardware mod to Adapter. Allows use of PB5 for SD Card #define WR_PORT GPIOB #define WR_PIN 6 #define CD_PORT GPIOB #define CD_PIN 7 #define CS_PORT GPIOB #define CS_PIN 8 #define RESET_PORT GPIOB #define RESET_PIN 9 // configure macros for the data pins #define write_8(d) { GPIOA->REGS(BSRR) = 0x00FF << 16; GPIOA->REGS(BSRR) = (d) & 0xFF; } #define read_8() (GPIOA->REGS(IDR) & 0xFF) // PA7 ..PA0 #define setWriteDir() {GP_OUT(GPIOA, CRL, 0xFFFFFFFF); } #define setReadDir() {GP_INP(GPIOA, CRL, 0xFFFFFFFF); } #elif IS_NUCLEO64 // Uno Shield on NUCLEO-64 #warning Uno Shield on NUCLEO-64 #define RD_PORT GPIOA //PA0 #define RD_PIN 0 #define WR_PORT GPIOA //PA1 #define WR_PIN 1 #define CD_PORT GPIOA //PA4 #define CD_PIN 4 #define CS_PORT GPIOB //PB0 #define CS_PIN 0 #define RESET_PORT GPIOC //PC1 #define RESET_PIN 1 // configure macros for the data pins #define AMASK ((1<<9)|(1<<10)|(1<<8)) //#0, #2, #7 #define BMASK ((1<<3)|(1<<5)|(1<<4)|(1<<10)) //#3, #4, #5, #6 #define CMASK ((1<<7)) //#1 #define write_8(d) { \ GPIOA->REGS(BSRR) = AMASK << 16; \ GPIOB->REGS(BSRR) = BMASK << 16; \ GPIOC->REGS(BSRR) = CMASK << 16; \ GPIOA->REGS(BSRR) = ( ((d) & (1<<0)) << 9) \ | (((d) & (1<<2)) << 8) \ | (((d) & (1<<7)) << 1); \ GPIOB->REGS(BSRR) = ( ((d) & (1<<3)) << 0) \ | (((d) & (1<<4)) << 1) \ | (((d) & (1<<5)) >> 1) \ | (((d) & (1<<6)) << 4); \ GPIOC->REGS(BSRR) = ( ((d) & (1<<1)) << 6); \ } #define read_8() ( ( ( (GPIOA->REGS(IDR) & (1<<9)) >> 9) \ | ((GPIOC->REGS(IDR) & (1<<7)) >> 6) \ | ((GPIOA->REGS(IDR) & (1<<10)) >> 8) \ | ((GPIOB->REGS(IDR) & (1<<3)) >> 0) \ | ((GPIOB->REGS(IDR) & (1<<5)) >> 1) \ | ((GPIOB->REGS(IDR) & (1<<4)) << 1) \ | ((GPIOB->REGS(IDR) & (1<<10)) >> 4) \ | ((GPIOA->REGS(IDR) & (1<<8)) >> 1))) #if defined(ARDUINO_NUCLEO_F103RB) || defined(ARDUINO_STM_NUCLEO_F103RB) //F103 has unusual GPIO modes // PA10,PA9,PA8 PB10 PB5,PB4,PB3 PC7 #define setWriteDir() {GP_OUT(GPIOA, CRH, 0xFFF); GP_OUT(GPIOB, CRH, 0xF00); GP_OUT(GPIOB, CRL, 0xFFF000); GP_OUT(GPIOC, CRL, 0xF0000000); } #define setReadDir() {GP_INP(GPIOA, CRH, 0xFFF); GP_INP(GPIOB, CRH, 0xF00); GP_INP(GPIOB, CRL, 0xFFF000); GP_INP(GPIOC, CRL, 0xF0000000); } #else //F0xx, F3xx, F4xx, L0xx, L1xx, L4xx use MODER // PA10,PA9,PA8 PB10,PB5,PB4,PB3 PC7 #define setWriteDir() { setReadDir(); \ GPIOA->MODER |= 0x150000; GPIOB->MODER |= 0x100540; GPIOC->MODER |= 0x4000; } #define setReadDir() { GPIOA->MODER &= ~0x3F0000; GPIOB->MODER &= ~0x300FC0; GPIOC->MODER &= ~0xC000; } #endif #elif IS_NUCLEO144 // Uno Shield on NUCLEO-144 #warning Uno Shield on NUCLEO-144 #define RD_PORT GPIOA //PA3 #define RD_PIN 3 #define WR_PORT GPIOC //PC0 #define WR_PIN 0 #define CD_PORT GPIOC //PC3 #define CD_PIN 3 #define CS_PORT GPIOF //PF3 #define CS_PIN 3 #define RESET_PORT GPIOF //PF5 #define RESET_PIN 5 // configure macros for the data pins #define DMASK ((1<<15)) //#1 #define EMASK ((1<<13)|(1<<11)|(1<<9)) //#3, #5, #6 #define FMASK ((1<<12)|(1<<15)|(1<<14)|(1<<13)) //#0, #2, #4, #7 #define write_8(d) { \ GPIOD->REGS(BSRR) = DMASK << 16; \ GPIOE->REGS(BSRR) = EMASK << 16; \ GPIOF->REGS(BSRR) = FMASK << 16; \ GPIOD->REGS(BSRR) = ( ((d) & (1<<1)) << 14); \ GPIOE->REGS(BSRR) = ( ((d) & (1<<3)) << 10) \ | (((d) & (1<<5)) << 6) \ | (((d) & (1<<6)) << 3); \ GPIOF->REGS(BSRR) = ( ((d) & (1<<0)) << 12) \ | (((d) & (1<<2)) << 13) \ | (((d) & (1<<4)) << 10) \ | (((d) & (1<<7)) << 6); \ } #define read_8() ( ( ( (GPIOF->REGS(IDR) & (1<<12)) >> 12) \ | ((GPIOD->REGS(IDR) & (1<<15)) >> 14) \ | ((GPIOF->REGS(IDR) & (1<<15)) >> 13) \ | ((GPIOE->REGS(IDR) & (1<<13)) >> 10) \ | ((GPIOF->REGS(IDR) & (1<<14)) >> 10) \ | ((GPIOE->REGS(IDR) & (1<<11)) >> 6) \ | ((GPIOE->REGS(IDR) & (1<<9)) >> 3) \ | ((GPIOF->REGS(IDR) & (1<<13)) >> 6))) // PD15 PE13,PE11,PE9 PF15,PF14,PF13,PF12 #define setWriteDir() { setReadDir(); \ GPIOD->MODER |= 0x40000000; GPIOE->MODER |= 0x04440000; GPIOF->MODER |= 0x55000000; } #define setReadDir() { GPIOD->MODER &= ~0xC0000000; GPIOE->MODER &= ~0x0CCC0000; GPIOF->MODER &= ~0xFF000000; } #elif defined(ARDUINO_MAPLE_REV3) // Uno Shield on MAPLE_REV3 board #warning Uno Shield on MAPLE_REV3 board #define RD_PORT GPIOC #define RD_PIN 0 #define WR_PORT GPIOC #define WR_PIN 1 #define CD_PORT GPIOC #define CD_PIN 2 #define CS_PORT GPIOC #define CS_PIN 3 #define RESET_PORT GPIOC #define RESET_PIN 4 // configure macros for the data pins #define write_8(d) { \ GPIOA->REGS(BSRR) = 0x0703 << 16; \ GPIOB->REGS(BSRR) = 0x00E0 << 16; \ GPIOA->REGS(BSRR) = ( ((d) & (1<<0)) << 10) \ | (((d) & (1<<2)) >> 2) \ | (((d) & (1<<3)) >> 2) \ | (((d) & (1<<6)) << 2) \ | (((d) & (1<<7)) << 2); \ GPIOB->REGS(BSRR) = ( ((d) & (1<<1)) << 6) \ | (((d) & (1<<4)) << 1) \ | (((d) & (1<<5)) << 1); \ } #define read_8() ( ( ( (GPIOA->REGS(IDR) & (1<<10)) >> 10) \ | ((GPIOB->REGS(IDR) & (1<<7)) >> 6) \ | ((GPIOA->REGS(IDR) & (1<<0)) << 2) \ | ((GPIOA->REGS(IDR) & (1<<1)) << 2) \ | ((GPIOB->REGS(IDR) & (1<<5)) >> 1) \ | ((GPIOB->REGS(IDR) & (1<<6)) >> 1) \ | ((GPIOA->REGS(IDR) & (1<<8)) >> 2) \ | ((GPIOA->REGS(IDR) & (1<<9)) >> 2))) // PA10,PA9,PA8 PA1,PA0 PB7,PB6,PB5 #define setWriteDir() {GP_OUT(GPIOA, CRH, 0xFFF); GP_OUT(GPIOA, CRL, 0xFF); GP_OUT(GPIOB, CRL, 0xFFF00000); } #define setReadDir() {GP_INP(GPIOA, CRH, 0xFFF); GP_INP(GPIOA, CRL, 0xFF); GP_INP(GPIOB, CRL, 0xFFF00000); } #else #error REGS group #endif #ifndef IDLE_DELAY #define IDLE_DELAY { WR_IDLE; } #endif #define write8(x) { write_8(x); WRITE_DELAY; WR_STROBE; IDLE_DELAY; } #define write16(x) { uint8_t h = (x)>>8, l = x; write8(h); write8(l); } #define READ_8(dst) { RD_STROBE; READ_DELAY; dst = read_8(); RD_IDLE2; RD_IDLE; } #define READ_16(dst) { uint8_t hi; READ_8(hi); READ_8(dst); dst |= (hi << 8); } //################################### ESP32 ############################## #elif defined(ESP32) //regular UNO shield on TTGO D1 R32 (ESP32) #define LCD_RD 2 //LED #define LCD_WR 4 #define LCD_RS 15 //hard-wired to A2 (GPIO35) #define LCD_CS 33 //hard-wired to A3 (GPIO34) #define LCD_RST 32 //hard-wired to A4 (GPIO36) #define LCD_D0 12 #define LCD_D1 13 #define LCD_D2 26 #define LCD_D3 25 #define LCD_D4 17 #define LCD_D5 16 #define LCD_D6 27 #define LCD_D7 14 #define RD_PORT GPIO.out #define RD_PIN LCD_RD #define WR_PORT GPIO.out #define WR_PIN LCD_WR #define CD_PORT GPIO.out #define CD_PIN LCD_RS #define CS_PORT GPIO.out1.val #define CS_PIN LCD_CS #define RESET_PORT GPIO.out1.val #define RESET_PIN LCD_RST static inline uint32_t map_8(uint32_t d) { return ( 0 | ((d & (1 << 0)) << (LCD_D0 - 0)) | ((d & (1 << 1)) << (LCD_D1 - 1)) | ((d & (1 << 2)) << (LCD_D2 - 2)) | ((d & (1 << 3)) << (LCD_D3 - 3)) | ((d & (1 << 4)) << (LCD_D4 - 4)) | ((d & (1 << 5)) << (LCD_D5 - 5)) | ((d & (1 << 6)) << (LCD_D6 - 6)) | ((d & (1 << 7)) << (LCD_D7 - 7)) ); } static inline uint8_t map_32(uint32_t d) { return ( 0 | ((d & (1 << LCD_D0)) >> (LCD_D0 - 0)) | ((d & (1 << LCD_D1)) >> (LCD_D1 - 1)) | ((d & (1 << LCD_D2)) >> (LCD_D2 - 2)) | ((d & (1 << LCD_D3)) >> (LCD_D3 - 3)) | ((d & (1 << LCD_D4)) >> (LCD_D4 - 4)) | ((d & (1 << LCD_D5)) >> (LCD_D5 - 5)) | ((d & (1 << LCD_D6)) >> (LCD_D6 - 6)) | ((d & (1 << LCD_D7)) >> (LCD_D7 - 7)) ); } static inline void write_8(uint16_t data) { GPIO.out_w1tc = map_8(0xFF); //could define once as DMASK GPIO.out_w1ts = map_8(data); } static inline uint8_t read_8() { return map_32(GPIO.in); } static void setWriteDir() { pinMode(LCD_D0, OUTPUT); pinMode(LCD_D1, OUTPUT); pinMode(LCD_D2, OUTPUT); pinMode(LCD_D3, OUTPUT); pinMode(LCD_D4, OUTPUT); pinMode(LCD_D5, OUTPUT); pinMode(LCD_D6, OUTPUT); pinMode(LCD_D7, OUTPUT); } static void setReadDir() { pinMode(LCD_D0, INPUT); pinMode(LCD_D1, INPUT); pinMode(LCD_D2, INPUT); pinMode(LCD_D3, INPUT); pinMode(LCD_D4, INPUT); pinMode(LCD_D5, INPUT); pinMode(LCD_D6, INPUT); pinMode(LCD_D7, INPUT); } #define WRITE_DELAY { } #define READ_DELAY { } #define write8(x) { write_8(x); WRITE_DELAY; WR_STROBE; } #define write16(x) { uint8_t h = (x)>>8, l = x; write8(h); write8(l); } #define READ_8(dst) { RD_STROBE; READ_DELAY; dst = read_8(); RD_IDLE; } #define READ_16(dst) { uint8_t hi; READ_8(hi); READ_8(dst); dst |= (hi << 8); } #define PIN_LOW(p, b) (digitalWrite(b, LOW)) #define PIN_HIGH(p, b) (digitalWrite(b, HIGH)) #define PIN_OUTPUT(p, b) (pinMode(b, OUTPUT)) #else #error MCU unsupported #endif // regular UNO shields on Arduino boards #endif //!defined(USE_SPECIAL) || defined (USE_SPECIAL_FAIL) #define RD_ACTIVE PIN_LOW(RD_PORT, RD_PIN) #define RD_IDLE PIN_HIGH(RD_PORT, RD_PIN) #define RD_OUTPUT PIN_OUTPUT(RD_PORT, RD_PIN) #define WR_ACTIVE PIN_LOW(WR_PORT, WR_PIN) #define WR_IDLE PIN_HIGH(WR_PORT, WR_PIN) #define WR_OUTPUT PIN_OUTPUT(WR_PORT, WR_PIN) #define CD_COMMAND PIN_LOW(CD_PORT, CD_PIN) #define CD_DATA PIN_HIGH(CD_PORT, CD_PIN) #define CD_OUTPUT PIN_OUTPUT(CD_PORT, CD_PIN) #define CS_ACTIVE PIN_LOW(CS_PORT, CS_PIN) #define CS_IDLE PIN_HIGH(CS_PORT, CS_PIN) #define CS_OUTPUT PIN_OUTPUT(CS_PORT, CS_PIN) #define RESET_ACTIVE PIN_LOW(RESET_PORT, RESET_PIN) #define RESET_IDLE PIN_HIGH(RESET_PORT, RESET_PIN) #define RESET_OUTPUT PIN_OUTPUT(RESET_PORT, RESET_PIN) // General macros. IOCLR registers are 1 cycle when optimised. #define WR_STROBE { WR_ACTIVE; WR_IDLE; } //PWLW=TWRL=50ns #define RD_STROBE RD_IDLE, RD_ACTIVE, RD_ACTIVE, RD_ACTIVE //PWLR=TRDL=150ns, tDDR=100ns #if !defined(GPIO_INIT) #define GPIO_INIT() #endif #define CTL_INIT() { GPIO_INIT(); RD_OUTPUT; WR_OUTPUT; CD_OUTPUT; CS_OUTPUT; RESET_OUTPUT; } #define WriteCmd(x) { CD_COMMAND; write16(x); CD_DATA; } #define WriteData(x) { write16(x); }