![](/media/cache/img/default_profile.jpg.50x50_q85.jpg)
Gyro_MPU3300
Dependencies: Gyro_MPU3300 mbed
Fork of MPU3300 by
main.cpp
- Committer:
- gkumar
- Date:
- 2015-02-13
- Revision:
- 0:7e0ed4a0d584
File content as of revision 0:7e0ed4a0d584:
#include<mbed.h> #include "MPU3300.h" //header file which includes all the register addresses and //Bit configuration of those registers SPI spi (PTD6,PTD7,PTD5) ; // MOSI,MISO, CLOCK pins being used on //microcontroller(in order) DigitalOut ssn (PTA13); //Slave Select pin Serial pc(USBTX,USBRX); InterruptIn dr(PTD2); //Interrupt pin Ticker tr; //Ticker function to give values for limited amount of time uint8_t trFlag; //ticker Flag uint8_t drFlag; //data-ready interrupt flag void trSub(); void drSub(); void init_gyro(); void execute_gyro(); int main(void) { init_gyro(); //Initializing Gyroscope registers and setting them to our required configuration execute_gyro(); //Executing gyroscope for measuring angular rates return 0; } void drSub() //In this function we setting data-ready flag to 1 { drFlag=1; } void trSub() //In this function we are setting ticker flag to 0 { trFlag=0; } void init_gyro() { uint8_t response; ssn=1; //Deselecting the chip spi.format(8,3); // Spi format is 8 bits, and clock mode 3 spi.frequency(1000000); //frequency to be set as 1MHz drFlag=0; //Intially defining data-ready flag to be 0 dr.mode(PullDown); dr.rise(&drSub); __disable_irq(); /*Following the above mentioned algorithm for initializing the register and changing its configuration*/ ssn=0; //Selecting chip(Mpu-3300) spi.write(USER_CTRL|READFLAG); //sending USER_CTRL address with read bit response=spi.write(DUMMYBIT); //sending dummy bit to get default values of the register ssn=1; //Deselecting the chip wait(0.1); //waiting according the product specifications ssn=0; //again selecting the chip spi.write(USER_CTRL); //sending USER_CTRL address without read bit spi.write(response|BIT_I2C_IF_DIS); //disabling the I2C mode in the register ssn=1; //deselecting the chip wait(0.1); // waiting for 100ms before going for another register ssn=0; spi.write(PWR_MGMT_1|READFLAG); //Power Management register-1 response=spi.write(DUMMYBIT); ssn=1; wait(0.1); ssn=0; spi.write(PWR_MGMT_1); response=spi.write(response|BIT_CLKSEL_X); //Selecting the X axis gyroscope as clock as mentioned above ssn=1; wait(0.1); ssn=0; spi.write(GYRO_CONFIG|READFLAG); //sending GYRO_CONFIG address with read bit response=spi.write(DUMMYBIT); ssn=1; wait(0.1); ssn=0; spi.write(GYRO_CONFIG); //sending GYRO_CONFIG address to write to register spi.write(response&(~(BITS_FS_SEL_3|BITS_FS_SEL_4))); //selecting a full scale mode of +/=225 deg/sec ssn=1; wait(0.1); ssn=0; spi.write(CONFIG|READFLAG); //sending CONFIG address with read bit response=spi.write(DUMMYBIT); ssn=1; wait(0.1); ssn=0; spi.write(CONFIG); //sending CONFIG address to write to register spi.write(response|BITS_DLPF_CFG); //selecting a bandwidth of 42 hz and delay of 4.8ms ssn=1; wait(0.1); ssn=0; spi.write(SMPLRT_DIV|READFLAG); //sending SMPLRT_DIV address with read bit response=spi.write(DUMMYBIT); ssn=1; wait(0.1); ssn=0; spi.write(SMPLRT_DIV); //sending SMPLRT_DIV address to write to register spi.write(response&BITS_SMPLRT_DIV); //setting the sampling rate division to be 0 to make sample rate = gyroscopic output rate ssn=1; wait(0.1); ssn=0; spi.write(INT_ENABLE|READFLAG); //sending address of INT_ENABLE with readflag response=spi.write(DUMMYBIT); //sending dummy byte to get the default values of the // regiser ssn=1; wait(0.1); ssn=0; spi.write(INT_ENABLE); //sending INT_ENABLE address to write to register spi.write(response|BIT_DATA_RDY_ENABLE); //Enbling data ready interrupt ssn=1; wait(0.1); __enable_irq(); } void execute_gyro() { uint8_t response; uint8_t MSB,LSB; int16_t bit_data; float data[3],error[3]={0,0,0}; //declaring error array to add to the values when required float senstivity = 145.6; //senstivity is 145.6 for full scale mode of +/-225 deg/sec ssn=0; spi.write(PWR_MGMT_1|READFLAG); //sending address of INT_ENABLE with readflag response=spi.write(DUMMYBIT); // ssn=1; wait(0.1); ssn=0; spi.write(PWR_MGMT_1); //sending PWR_MGMT_1 address to write to register response=spi.write(response&(~(BIT_SLEEP))); //waking up the gyroscope from sleep ssn=1; wait(0.1); trFlag=1; tr.attach(&trSub,1); //executes the function trSub afer 1sec while(trFlag) { if(drFlag==1) { ssn=0; spi.write(GYRO_XOUT_H|READFLAG); //sending address of PWR_MGMT_1 with readflag for(int i=0;i<3;i++) { MSB = spi.write(DUMMYBIT); //reading the MSB values of x,y and z respectively LSB = spi.write(DUMMYBIT); //reading the LSB values of x,y and z respectively bit_data= ((int16_t)MSB<<8)|LSB; //concatenating to get 16 bit 2's complement of the required gyroscope values data[i]=(float)bit_data; data[i]=data[i]/senstivity; //dividing with senstivity to get the readings in deg/sec data[i]+=error[i]; //adding with error to remove offset errors } ssn=1; for (int i=0;i<3;i++) { printf("%f\t",data[i]); //printing the angular velocity values } printf("\n"); break; } drFlag=0; } ssn=0; spi.write(PWR_MGMT_1|READFLAG); //sending address of PWR_MGMT_1 with readflag response=spi.write(DUMMYBIT); ssn=1; wait(0.1); ssn=0; spi.write(PWR_MGMT_1); //sending PWR_MGMT_1 address to write to register response=spi.write(response|BIT_SLEEP); //setting the gyroscope in sleep mode ssn=1; wait(0.1); }