Diff: INA226.h

Revision:

0:3984961a3725

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/INA226.h	Wed Aug 07 22:51:12 2013 +0000
@@ -0,0 +1,133 @@
+/*
+ * Texas Instruments INA226 voltage/ current/ power monitor library
+ *
+ *
+ * Copyright (c) 2013 Davy Van Belle, MIT License
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of this software 
+ * and associated documentation files (the "Software"), to deal in the Software without restriction, 
+ * including without limitation the rights to use, copy, modify, merge, publish, distribute, 
+ * sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is 
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all copies or 
+ * substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING 
+ * BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND 
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, 
+ * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, 
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/** @file
+ * @brief INA226 I2C
+ */
+ 
+#ifndef INA226_H
+#define INA226_H
+
+#include "mbed.h"
+
+#define CONF 0x00
+
+#define VSHUNT 0x01
+#define VBUS 0x02
+#define POWER 0x03
+#define CURRENT 0x04
+#define CAL 0x05
+#define MASK 0x06
+#define ALERT 0x07
+
+#define DIE_ID 0xFF
+
+#define SHUNT_LSB 0.0000025
+#define BUS_LSB 0.00125
+
+
+
+/** INA226 class 
+ */
+class INA226 {
+public:
+    /** init INA226 class
+     * @param *i2c pointer to I2C serial interface
+     * @param addr sensor I2C address
+     */
+    INA226 (I2C* i2c, char addr); 
+
+    /** Set the configuration of the device
+     * @param reg desired Configure Register bits
+     */
+    void setConfig (unsigned short reg);
+    
+    /** Get device Configuration register
+     */  
+    unsigned short getConfig();
+    
+    /** Get the voltage over the shunt
+    */
+    float getShuntVolt();
+
+    /** Get the voltage of the bus rail
+     */
+    float getBusVolt();
+    
+    /** Get the current measured through the shunt.
+     * in order to get the current you need to set the shut resistor value first
+     */  
+    float getCurrent();
+    
+    float getPower();
+    
+    /** Set the Calibartion register 
+    */
+    void setCalibration(unsigned short reg);
+    
+    /** Get the Calibration register
+    */
+    unsigned short getCalibration();
+    
+    /** Set the mask/enable Register
+    */
+    void setMaskEnable(unsigned short reg);
+    
+    /** Get the mask/enable Register
+    */
+    unsigned short getMaskEnable();
+    
+    void setAlertLimit(unsigned short reg);
+    
+    unsigned short getAlertLimit();
+    
+    /** Get the unique ID of the device
+    */
+    unsigned short getID();
+    
+    /** Set the shunt resistor
+    *@param val value in ohm
+    */
+    void setShuntRValue(float val);
+    
+    float getShuntRValue(void);
+    
+    /** Set the current LSB for maximum current in decimal
+    */
+    void setCurrentLSB(float val);
+
+    float getCurrentLSB(float val);
+    
+protected:
+
+
+private:
+    char _addr;
+    I2C *_i2c;
+    float ShuntR;
+    float CURR_LSB;
+    
+    
+    
+};
+    
+#endif    
\ No newline at end of file