Diff: Encoder/EncoderMspInitL1.cpp

Revision:

0:95f924550159

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/Encoder/EncoderMspInitL1.cpp	Sat May 21 04:17:35 2016 +0000
@@ -0,0 +1,63 @@
+#include "mbed.h"
+/*
+ * HAL_TIM_Encoder_MspInit()
+ * Overrides the __weak function stub in stm32l4xx_hal_tim.h
+ *
+ * Edit the below for your preferred pin wiring & pullup/down
+ * I have encoder common at 3V3, using GPIO_PULLDOWN on inputs.
+ * Encoder A&B outputs connected directly to GPIOs.
+ *
+ * http://www.st.com/st-web-ui/static/active/en/resource/technical/document/datasheet/DM00098321.pdf
+ * Table 9 has GPIO alternate function pinout mappings.
+ *
+ * TIM2_CH1: AF1 @ PA_0, PA_5, PA_15, PE_9
+ * TIM2_CH2: AF1 @ PA_1, PB_3, PE_10
+ *
+ * TIM3_CH1: AF2 @ PA_6, PB_4, PC_6, PE_3
+ * TIM3_CH2: AF2 @ PA_7, PB_5, PC_7, PE_4
+ *
+ * TIM4_CH1: AF2 @ PB_6, PD_12
+ * TIM4_CH2: AF2 @ PB_7, PD_13
+ *
+ * TIM5_CH1: AF2 @ PA_0*    *TIM5 used by mbed system ticker so unavailable
+ * TIM5_CH2: AF2 @ PA_1*
+ *
+ */
+
+#ifdef TARGET_STM32L1
+void HAL_TIM_Encoder_MspInit(TIM_HandleTypeDef *htim)
+{
+    GPIO_InitTypeDef GPIO_InitStruct;
+
+    if (htim->Instance == TIM2) { //PA0 PA1 = Nucleo A0 A1
+        __TIM2_CLK_ENABLE();
+        __GPIOA_CLK_ENABLE();
+        GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1;
+        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+        GPIO_InitStruct.Pull = GPIO_PULLDOWN;
+        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+        GPIO_InitStruct.Alternate = GPIO_AF1_TIM2;
+        HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+    }
+    else if (htim->Instance == TIM3) { //PB4 PB5 = Nucleo D5 D4
+        __TIM3_CLK_ENABLE();
+        __GPIOB_CLK_ENABLE();
+        GPIO_InitStruct.Pin = GPIO_PIN_4 | GPIO_PIN_5;
+        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+        GPIO_InitStruct.Pull = GPIO_PULLDOWN;
+        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+        GPIO_InitStruct.Alternate = GPIO_AF2_TIM3;
+        HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+    }
+    else if (htim->Instance == TIM4) { // PB6 PB7 = Nucleo D10 MORPHO_PB7
+        __TIM4_CLK_ENABLE();
+        __GPIOB_CLK_ENABLE();
+        GPIO_InitStruct.Pin = GPIO_PIN_6 | GPIO_PIN_7;
+        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+        GPIO_InitStruct.Pull = GPIO_PULLDOWN;
+        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+        GPIO_InitStruct.Alternate = GPIO_AF2_TIM4;
+        HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+    }
+}
+#endif
\ No newline at end of file