These are the examples provided for [[/users/frank26080115/libraries/LPC1700CMSIS_Lib/]] Note, the entire "program" is not compilable!
Diff: SSP/TI/abstract.h
- Revision:
- 0:bf7b9fba3924
diff -r 000000000000 -r bf7b9fba3924 SSP/TI/abstract.h --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/SSP/TI/abstract.h Sun Mar 20 05:38:56 2011 +0000 @@ -0,0 +1,102 @@ + ******************** (C) COPYRIGHT 2010 NXPSemiconductors ******************* + * @file SSP\TI\abstract.txt + * @author NXP MCU SW Application Team + * @version 2.0 + * @date + * @brief Description of the SSP TI example. + ****************************************************************************** + * Software that is described herein is for illustrative purposes only + * which provides customers with programming information regarding the + * products. This software is supplied "AS IS" without any warranties. + * NXP Semiconductors assumes no responsibility or liability for the + * use of the software, conveys no license or title under any patent, + * copyright, or mask work right to the product. NXP Semiconductors + * reserves the right to make changes in the software without + * notification. NXP Semiconductors also make no representation or + * warranty that such application will be suitable for the specified + * use without further testing or modification. + ****************************************************************************** + +@Example description: + Purpose: + This example describes how to use SSP peripheral with TI frame format. + Process: + This example uses two SSP peripherals in TI frame format, one is set + as master mode and the other is set as slave mode. + SSP master/slave configuration: + - CPHA = 0: data is sampled on the first clock edge of SCK. + - CPOL = 0: SCK is active high + - Clock rate = 1MHz + - DSS = 8: 8 bits per transfer + - MSTR = 0/1: SSP operates in Slave/Master mode + - FRF= 1: MicroWire Frame format + After initialize buffer, SPI master will transfer/receive data to/from SSP slave + in INTERRUPT mode. + After transmittion completed, receive and transmit buffer will be compared, if they + are not similar, the program will enter infinite loop and a error notice will + be displayed. + +@Directory contents: + \EWARM: includes EWARM (IAR) project and configuration files + \Keil: includes RVMDK (Keil)project and configuration files + + lpc17xx_libcfg.h: Library configuration file - include needed driver library for this example + makefile: Example's makefile (to build with GNU toolchain) + ti_test.c: Main program + +@How to run: + Hardware configuration: + This example was tested on: + Keil MCB1700 with LPC1768 vers.1 + These jumpers must be configured as following: + - VDDIO: ON + - VDDREGS: ON + - VBUS: ON + - Remain jumpers: OFF + IAR LPC1768 KickStart vers.A + These jumpers must be configured as following: + - PWR_SEL: depend on power source + - DBG_EN : ON + - Remain jumpers: OFF + + SSP Connection: + - P0.15 <-> P0.7 : SCK + - P0.16 <-> P0.6 : SSEL + - P0.17 <-> P0.8 : MISO + - P0.18 <-> P0.9 : MOSI + + Serial display configuration: (e.g: TeraTerm, Hyperterminal, Flash Magic...) + 115200bps + 8 data bit + No parity + 1 stop bit + No flow control + + Running mode: + This example can run on RAM/ROM mode. + + Note: If want to burn hex file to board by using Flash Magic, these jumpers need + to be connected: + - MCB1700 with LPC1768 ver.1: + + RST: ON + + ISP: ON + - IAR LPC1768 KickStart vers.A: + + RST_E: ON + + ISP_E: ON + + (Please reference "LPC1000 Software Development Toolchain" - chapter 4 "Creating and working with + LPC1000CMSIS project" for more information) + + Step to run: + - Step 1: Build example. + - Step 2: Burn hex file into board (if run on ROM mode) + - Step 3: Connect UART0 on this board to COM port on your computer + - Step 4: Configure hardware and serial display as above instruction + - Step 5: Run example, observe SSP transfer result on serial display + + (Pls see "LPC17xx Example Description" document - chapter "Examples > SSP > TI" + for more details) + +@Tip: + - Open \EWARM\*.eww project file to run example on IAR + - Open \RVMDK\*.uvproj project file to run example on Keil \ No newline at end of file