These are the examples provided for [[/users/frank26080115/libraries/LPC1700CMSIS_Lib/]] Note, the entire "program" is not compilable!
Diff: UART/RS485_Slave/abstract.h
- Revision:
- 0:bf7b9fba3924
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/UART/RS485_Slave/abstract.h Sun Mar 20 05:38:56 2011 +0000 @@ -0,0 +1,94 @@ + ******************** (C) COPYRIGHT 2010 NXPSemiconductors ******************* + * @file UART\RS485_slave\abstract.txt + * @author NXP MCU SW Application Team + * @version 2.0 + * @date + * @brief Description of the RS485_Slave example. + ****************************************************************************** + * Software that is described herein is for illustrative purposes only + * which provides customers with programming information regarding the + * products. This software is supplied "AS IS" without any warranties. + * NXP Semiconductors assumes no responsibility or liability for the + * use of the software, conveys no license or title under any patent, + * copyright, or mask work right to the product. NXP Semiconductors + * reserves the right to make changes in the software without + * notification. NXP Semiconductors also make no representation or + * warranty that such application will be suitable for the specified + * use without further testing or modification. + ****************************************************************************** + +@Example description: + Purpose: + This example describes how to use RS485 functionality on UART1 of LPC1768 + in slave mode. + Process: + RS485 function on UART1 acts as slave mode on RS485 bus. + RS485 Slave device in this example can operate in separate mode + as following: + - Slave device always receives all frames on RS485 bus, regardless + data frame (9 bit mode with parity stick '0') or slave address + frame (9 bit mode with parity stick '1'). + - Slave device does not always receive all frames on RS485 bus. In this + case, only slave address frame can trigger an interrupt event, + then slave device can accept the following data frame by determine that + slave address frame is its own address or not(implemented by software). + - Slave device is in auto slave address detection mode. In this mode, + only slave address frame with slave address value that matched with + pre-configured slave address will be accepted automatically (by hardware) + and trigger an interrupt callback event to handle following data frames. + +@Directory contents: + \EWARM: includes EWARM (IAR) project and configuration files + \Keil: includes RVMDK (Keil)project and configuration files + + lpc17xx_libcfg.h: Library configuration file - include needed driver library for this example + makefile: Example's makefile (to build with GNU toolchain) + rs485_slave.c: Main program + +@How to run: + Hardware configuration: + This example was tested on: + Keil MCB1700 with LPC1768 vers.1 + These jumpers must be configured as following: + - VDDIO: ON + - VDDREGS: ON + - VBUS: ON + - Remain jumpers: OFF + IAR LPC1768 KickStart vers.A + These jumpers must be configured as following: + - PWR_SEL: depend on power source + - DBG_EN : ON + - Remain jumpers: OFF + + RS485 Connection: + Pls see the 'Transceiver_Master.png' in this directory for wiring information. + + Running mode: + This example can run on RAM/ROM mode. + + Note: If want to burn hex file to board by using Flash Magic, these jumpers need + to be connected: + - MCB1700 with LPC1768 ver.1: + + RST: ON + + ISP: ON + - IAR LPC1768 KickStart vers.A: + + RST_E: ON + + ISP_E: ON + + (Please reference "LPC1000 Software Development Toolchain" - chapter 4 "Creating and working with + LPC1000CMSIS project" for more information) + + Step to run: + - Step 1: Build example. + - Step 2: Burn hex file into board (if run on ROM mode) + - Step 3: Connect UART0 on this board to COM port on your computer + - Step 4: Connect RS485 between master board and slave board (using ADM485) + - Step 5: Run example and using Serial display to monitor the communication between master and slave. + Note: The RS485 slave device must initialize first. + + (Pls see "LPC17xx Example Description" document - chapter "Examples > UART > RS485_Slave" + for more details) + +@Tip: + - Open \EWARM\*.eww project file to run example on IAR + - Open \RVMDK\*.uvproj project file to run example on Keil