Diff: LCD/NOKIA6610_LCD/abstract.h

Revision:

0:bf7b9fba3924

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/LCD/NOKIA6610_LCD/abstract.h	Sun Mar 20 05:38:56 2011 +0000
@@ -0,0 +1,86 @@
+ ******************** (C) COPYRIGHT 2010 NXPSemiconductors *******************
+ * @file    LCD\NOKIA6610_LCD\abstract.txt 
+ * @author  NXP MCU SW Application Team
+ * @version 2.0
+ * @date    
+ * @brief   Description of the LCD NOKIA6610 example.
+ ******************************************************************************
+ * Software that is described herein is for illustrative purposes only
+ * which provides customers with programming information regarding the
+ * products. This software is supplied "AS IS" without any warranties.
+ * NXP Semiconductors assumes no responsibility or liability for the
+ * use of the software, conveys no license or title under any patent,
+ * copyright, or mask work right to the product. NXP Semiconductors
+ * reserves the right to make changes in the software without
+ * notification. NXP Semiconductors also make no representation or
+ * warranty that such application will be suitable for the specified
+ * use without further testing or modification.
+ ******************************************************************************
+  
+@Example description:
+	Purpose:
+		This example describes how to use LCD NOKIA6610 on IAR-LPC1768-KS board
+	Process:
+		This example use LCD NOKIA6610 driver library that deriverd from IAR.
+		Using SPI protocol to communicate with LCD controller chip.
+		It starts by show NXP icon.
+		LCD operation can be controlled by using:
+			- AN_TRIM: ADC potentiometer - increase/decrease LCD backlight or contrast. 
+			- BUT1: used to adjust backlight.
+			- BUT2: used to adjust LCD contrast.		
+			
+@Directory contents:
+	\EWARM: includes EWARM (IAR) project and configuration files
+	\Keil:	includes RVMDK (Keil)project and configuration files 
+	
+	drv_glcd_cbcf.h: Graphic LCD configuration file
+	drv_glcd.h/.c: Graphic LCD driver
+	glcd_ll.h/.c: Graphic LCD low level functions
+	lcdtest.c: Main program
+	lpc17xx_libcfg.h: Library configuration file - include needed driver library for this example 
+	NXP_logo.h/.c: NXP icon data
+	Terminal_9_12x6: font (12x6) data
+	makefile: Example's makefile (to build with GNU toolchain)
+	
+
+@How to run:
+	Hardware configuration:		
+		This example was tested only on:
+			IAR LPC1768 KickStart vers.A
+				These jumpers must be configured as following:
+				- PWR_SEL: depend on power source
+				- DBG_EN : ON
+				- Remain jumpers: OFF
+
+	Running mode:
+		This example can run only on ROM mode.
+					
+		Note: If want to burn hex file to board by using Flash Magic, these jumpers need
+		to be connected:
+			- MCB1700 with LPC1768 ver.1:
+				+ RST: ON
+				+ ISP: ON
+			- IAR LPC1768 KickStart vers.A:
+				+ RST_E: ON
+				+ ISP_E: ON
+		
+		(Please reference "LPC1000 Software Development Toolchain" - chapter 4 "Creating and working with
+		LPC1000CMSIS project" for more information)
+	
+	Step to run:
+		- Step 1: Build example.
+		- Step 2: Burn hex file into board (if run on ROM mode)
+		- Step 3: Configure hardware as above instruction
+		- Step 4: Hit reset button to run example:
+					+ It shows NXP icon first.
+					+ Hit "BUT1" if want to adjust backlight, then turn ADC potentiometer AN_TRIM to 
+					  change LCD backlight.
+					+ Hit "BUT2" if want to adjust contrast, then turn ADC potentiometer AN_TRIM to 
+					  change LCD contrast.
+					  
+		(Pls see "LPC17xx Example Description" document - chapter "Examples > LCD > NOKIA6610_LCD"
+		for more details)
+		
+@Tip:
+	- Open \EWARM\*.eww project file to run example on IAR
+	- Open \RVMDK\*.uvproj project file to run example on Keil		
\ No newline at end of file