Filippo Casamassima
my fork
Fork of
mbed
by 
mbed official
TARGET_NUCLEO_F072RB/stm32f0xx_hal_usart.h
- Committer:
- Kojto
- Date:
- 2015-02-03
- Revision:
- 93:e188a91d3eaa
- Parent:
- 92:4fc01daae5a5
File content as of revision 93:e188a91d3eaa:
/**
******************************************************************************
* @file stm32f0xx_hal_usart.h
* @author MCD Application Team
* @version V1.2.0
* @date 11-December-2014
* @brief Header file of USART HAL module.
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32F0xx_HAL_USART_H
#define __STM32F0xx_HAL_USART_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32f0xx_hal_def.h"
/** @addtogroup STM32F0xx_HAL_Driver
* @{
*/
/** @addtogroup USART
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup USART_Exported_Types USART Exported Types
* @{
*/
/**
* @brief USART Init Structure definition
*/
typedef struct
{
uint32_t BaudRate; /*!< This member configures the Usart communication baud rate.
The baud rate is computed using the following formula:
Baud Rate Register = ((PCLKx) / ((huart->Init.BaudRate))) */
uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame.
This parameter can be a value of @ref USARTEx_Word_Length */
uint32_t StopBits; /*!< Specifies the number of stop bits transmitted.
This parameter can be a value of @ref USART_Stop_Bits */
uint32_t Parity; /*!< Specifies the parity mode.
This parameter can be a value of @ref USART_Parity
@note When parity is enabled, the computed parity is inserted
at the MSB position of the transmitted data (9th bit when
the word length is set to 9 data bits; 8th bit when the
word length is set to 8 data bits). */
uint32_t Mode; /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
This parameter can be a value of @ref USART_Mode */
uint32_t CLKPolarity; /*!< Specifies the steady state of the serial clock.
This parameter can be a value of @ref USART_Clock_Polarity */
uint32_t CLKPhase; /*!< Specifies the clock transition on which the bit capture is made.
This parameter can be a value of @ref USART_Clock_Phase */
uint32_t CLKLastBit; /*!< Specifies whether the clock pulse corresponding to the last transmitted
data bit (MSB) has to be output on the SCLK pin in synchronous mode.
This parameter can be a value of @ref USART_Last_Bit */
}USART_InitTypeDef;
/**
* @brief HAL State structures definition
*/
typedef enum
{
HAL_USART_STATE_RESET = 0x00, /*!< Peripheral is not initialized */
HAL_USART_STATE_READY = 0x01, /*!< Peripheral Initialized and ready for use */
HAL_USART_STATE_BUSY = 0x02, /*!< an internal process is ongoing */
HAL_USART_STATE_BUSY_TX = 0x12, /*!< Data Transmission process is ongoing */
HAL_USART_STATE_BUSY_RX = 0x22, /*!< Data Reception process is ongoing */
HAL_USART_STATE_BUSY_TX_RX = 0x32, /*!< Data Transmission Reception process is ongoing */
HAL_USART_STATE_TIMEOUT = 0x03, /*!< Timeout state */
HAL_USART_STATE_ERROR = 0x04 /*!< Error */
}HAL_USART_StateTypeDef;
/**
* @brief USART clock sources definitions
*/
typedef enum
{
USART_CLOCKSOURCE_PCLK1 = 0x00, /*!< PCLK1 clock source */
USART_CLOCKSOURCE_HSI = 0x02, /*!< HSI clock source */
USART_CLOCKSOURCE_SYSCLK = 0x04, /*!< SYSCLK clock source */
USART_CLOCKSOURCE_LSE = 0x08, /*!< LSE clock source */
USART_CLOCKSOURCE_UNDEFINED = 0x10 /*!< undefined clock source */
}USART_ClockSourceTypeDef;
/**
* @brief USART handle Structure definition
*/
typedef struct
{
USART_TypeDef *Instance; /*!< USART registers base address */
USART_InitTypeDef Init; /*!< USART communication parameters */
uint8_t *pTxBuffPtr; /*!< Pointer to USART Tx transfer Buffer */
uint16_t TxXferSize; /*!< USART Tx Transfer size */
uint16_t TxXferCount; /*!< USART Tx Transfer Counter */
uint8_t *pRxBuffPtr; /*!< Pointer to USART Rx transfer Buffer */
uint16_t RxXferSize; /*!< USART Rx Transfer size */
uint16_t RxXferCount; /*!< USART Rx Transfer Counter */
uint16_t Mask; /*!< USART Rx RDR register mask */
DMA_HandleTypeDef *hdmatx; /*!< USART Tx DMA Handle parameters */
DMA_HandleTypeDef *hdmarx; /*!< USART Rx DMA Handle parameters */
HAL_LockTypeDef Lock; /*!< Locking object */
HAL_USART_StateTypeDef State; /*!< USART communication state */
__IO uint32_t ErrorCode; /*!< USART Error code
This parameter can be a value of @ref USART_Error */
}USART_HandleTypeDef;
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup USART_Exported_Constants USART Exported constants
* @{
*/
/** @defgroup USART_Error USART Error
* @{
*/
#define HAL_USART_ERROR_NONE ((uint32_t)0x00000000) /*!< No error */
#define HAL_USART_ERROR_PE ((uint32_t)0x00000001) /*!< Parity error */
#define HAL_USART_ERROR_NE ((uint32_t)0x00000002) /*!< Noise error */
#define HAL_USART_ERROR_FE ((uint32_t)0x00000004) /*!< frame error */
#define HAL_USART_ERROR_ORE ((uint32_t)0x00000008) /*!< Overrun error */
#define HAL_USART_ERROR_DMA ((uint32_t)0x00000010) /*!< DMA transfer error */
/**
* @}
*/
/** @defgroup USART_Stop_Bits USART Number of Stop Bits
* @{
*/
#define USART_STOPBITS_1 ((uint32_t)0x0000)
#define USART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1)
#define USART_STOPBITS_1_5 ((uint32_t)(USART_CR2_STOP_0 | USART_CR2_STOP_1))
#define IS_USART_STOPBITS(STOPBITS) (((STOPBITS) == USART_STOPBITS_1) || \
((STOPBITS) == USART_STOPBITS_1_5) || \
((STOPBITS) == USART_STOPBITS_2))
/**
* @}
*/
/** @defgroup USART_Parity USART Parity
* @{
*/
#define USART_PARITY_NONE ((uint32_t)0x0000)
#define USART_PARITY_EVEN ((uint32_t)USART_CR1_PCE)
#define USART_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS))
#define IS_USART_PARITY(PARITY) (((PARITY) == USART_PARITY_NONE) || \
((PARITY) == USART_PARITY_EVEN) || \
((PARITY) == USART_PARITY_ODD))
/**
* @}
*/
/** @defgroup USART_Mode USART Mode
* @{
*/
#define USART_MODE_RX ((uint32_t)USART_CR1_RE)
#define USART_MODE_TX ((uint32_t)USART_CR1_TE)
#define USART_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE))
#define IS_USART_MODE(MODE) ((((MODE) & (uint32_t)0xFFFFFFF3) == 0x00) && ((MODE) != (uint32_t)0x00))
/**
* @}
*/
/** @defgroup USART_Clock USART Clock
* @{
*/
#define USART_CLOCK_DISABLED ((uint32_t)0x0000)
#define USART_CLOCK_ENABLED ((uint32_t)USART_CR2_CLKEN)
#define IS_USART_CLOCK(CLOCK) (((CLOCK) == USART_CLOCK_DISABLED) || \
((CLOCK) == USART_CLOCK_ENABLED))
/**
* @}
*/
/** @defgroup USART_Clock_Polarity USART Clock Polarity
* @{
*/
#define USART_POLARITY_LOW ((uint32_t)0x0000)
#define USART_POLARITY_HIGH ((uint32_t)USART_CR2_CPOL)
#define IS_USART_POLARITY(CPOL) (((CPOL) == USART_POLARITY_LOW) || ((CPOL) == USART_POLARITY_HIGH))
/**
* @}
*/
/** @defgroup USART_Clock_Phase USART Clock Phase
* @{
*/
#define USART_PHASE_1EDGE ((uint32_t)0x0000)
#define USART_PHASE_2EDGE ((uint32_t)USART_CR2_CPHA)
#define IS_USART_PHASE(CPHA) (((CPHA) == USART_PHASE_1EDGE) || ((CPHA) == USART_PHASE_2EDGE))
/**
* @}
*/
/** @defgroup USART_Last_Bit USART Last Bit
* @{
*/
#define USART_LASTBIT_DISABLE ((uint32_t)0x0000)
#define USART_LASTBIT_ENABLE ((uint32_t)USART_CR2_LBCL)
#define IS_USART_LASTBIT(LASTBIT) (((LASTBIT) == USART_LASTBIT_DISABLE) || \
((LASTBIT) == USART_LASTBIT_ENABLE))
/**
* @}
*/
/** @defgroup USART_Flags USART Flags
* Elements values convention: 0xXXXX
* - 0xXXXX : Flag mask in the ISR register
* @{
*/
#define USART_FLAG_REACK ((uint32_t)0x00400000)
#define USART_FLAG_TEACK ((uint32_t)0x00200000)
#define USART_FLAG_BUSY ((uint32_t)0x00010000)
#define USART_FLAG_CTS ((uint32_t)0x00000400)
#define USART_FLAG_CTSIF ((uint32_t)0x00000200)
#define USART_FLAG_LBDF ((uint32_t)0x00000100)
#define USART_FLAG_TXE ((uint32_t)0x00000080)
#define USART_FLAG_TC ((uint32_t)0x00000040)
#define USART_FLAG_RXNE ((uint32_t)0x00000020)
#define USART_FLAG_IDLE ((uint32_t)0x00000010)
#define USART_FLAG_ORE ((uint32_t)0x00000008)
#define USART_FLAG_NE ((uint32_t)0x00000004)
#define USART_FLAG_FE ((uint32_t)0x00000002)
#define USART_FLAG_PE ((uint32_t)0x00000001)
/**
* @}
*/
/** @defgroup USART_Interrupt_definition USART Interrupts Definition
* Elements values convention: 0000ZZZZ0XXYYYYYb
* - YYYYY : Interrupt source position in the XX register (5bits)
* - XX : Interrupt source register (2bits)
* - 01: CR1 register
* - 10: CR2 register
* - 11: CR3 register
* - ZZZZ : Flag position in the ISR register(4bits)
* @{
*/
#define USART_IT_PE ((uint16_t)0x0028)
#define USART_IT_TXE ((uint16_t)0x0727)
#define USART_IT_TC ((uint16_t)0x0626)
#define USART_IT_RXNE ((uint16_t)0x0525)
#define USART_IT_IDLE ((uint16_t)0x0424)
#define USART_IT_ERR ((uint16_t)0x0060)
#define USART_IT_ORE ((uint16_t)0x0300)
#define USART_IT_NE ((uint16_t)0x0200)
#define USART_IT_FE ((uint16_t)0x0100)
/**
* @}
*/
/** @defgroup USART_IT_CLEAR_Flags USART Interruption Clear Flags
* @{
*/
#define USART_CLEAR_PEF USART_ICR_PECF /*!< Parity Error Clear Flag */
#define USART_CLEAR_FEF USART_ICR_FECF /*!< Framing Error Clear Flag */
#define USART_CLEAR_NEF USART_ICR_NCF /*!< Noise detected Clear Flag */
#define USART_CLEAR_OREF USART_ICR_ORECF /*!< OverRun Error Clear Flag */
#define USART_CLEAR_IDLEF USART_ICR_IDLECF /*!< IDLE line detected Clear Flag */
#define USART_CLEAR_TCF USART_ICR_TCCF /*!< Transmission Complete Clear Flag */
#define USART_CLEAR_CTSF USART_ICR_CTSCF /*!< CTS Interrupt Clear Flag */
/**
* @}
*/
/** @defgroup USART_Request_Parameters USART Request Parameters
* @{
*/
#define USART_RXDATA_FLUSH_REQUEST ((uint32_t)USART_RQR_RXFRQ) /*!< Receive Data flush Request */
#define USART_TXDATA_FLUSH_REQUEST ((uint32_t)USART_RQR_TXFRQ) /*!< Transmit data flush Request */
#define IS_USART_REQUEST_PARAMETER(PARAM) (((PARAM) == USART_RXDATA_FLUSH_REQUEST) || \
((PARAM) == USART_TXDATA_FLUSH_REQUEST))
/**
* @}
*/
/** @defgroup USART_Interruption_Mask USART interruptions flag mask
* @{
*/
#define USART_IT_MASK ((uint16_t)0x001F)
/**
* @}
*/
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup USART_Exported_Macros USART Exported Macros
* @{
*/
/** @brief Reset USART handle state
* @param __HANDLE__: USART handle.
* @retval None
*/
#define __HAL_USART_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_USART_STATE_RESET)
/** @brief Checks whether the specified USART flag is set or not.
* @param __HANDLE__: specifies the USART Handle
* @param __FLAG__: specifies the flag to check.
* This parameter can be one of the following values:
* @arg USART_FLAG_REACK: Receive enable ackowledge flag
* @arg USART_FLAG_TEACK: Transmit enable ackowledge flag
* @arg USART_FLAG_BUSY: Busy flag
* @arg USART_FLAG_CTS: CTS Change flag
* @arg USART_FLAG_TXE: Transmit data register empty flag
* @arg USART_FLAG_TC: Transmission Complete flag
* @arg USART_FLAG_RXNE: Receive data register not empty flag
* @arg USART_FLAG_IDLE: Idle Line detection flag
* @arg USART_FLAG_ORE: OverRun Error flag
* @arg USART_FLAG_NE: Noise Error flag
* @arg USART_FLAG_FE: Framing Error flag
* @arg USART_FLAG_PE: Parity Error flag
* @retval The new state of __FLAG__ (TRUE or FALSE).
*/
#define __HAL_USART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->ISR & (__FLAG__)) == (__FLAG__))
/** @brief Enables the specified USART interrupt.
* @param __HANDLE__: specifies the USART Handle
* @param __INTERRUPT__: specifies the USART interrupt source to enable.
* This parameter can be one of the following values:
* @arg USART_IT_TXE: Transmit Data Register empty interrupt
* @arg USART_IT_TC: Transmission complete interrupt
* @arg USART_IT_RXNE: Receive Data register not empty interrupt
* @arg USART_IT_IDLE: Idle line detection interrupt
* @arg USART_IT_PE: Parity Error interrupt
* @arg USART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
* @retval None
*/
#define __HAL_USART_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((((uint8_t)(__INTERRUPT__)) >> 5U) == 1)? ((__HANDLE__)->Instance->CR1 |= (1U << ((__INTERRUPT__) & USART_IT_MASK))): \
((((uint8_t)(__INTERRUPT__)) >> 5U) == 2)? ((__HANDLE__)->Instance->CR2 |= (1U << ((__INTERRUPT__) & USART_IT_MASK))): \
((__HANDLE__)->Instance->CR3 |= (1U << ((__INTERRUPT__) & USART_IT_MASK))))
/** @brief Disables the specified USART interrupt.
* @param __HANDLE__: specifies the USART Handle.
* @param __INTERRUPT__: specifies the USART interrupt source to disable.
* This parameter can be one of the following values:
* @arg USART_IT_TXE: Transmit Data Register empty interrupt
* @arg USART_IT_TC: Transmission complete interrupt
* @arg USART_IT_RXNE: Receive Data register not empty interrupt
* @arg USART_IT_IDLE: Idle line detection interrupt
* @arg USART_IT_PE: Parity Error interrupt
* @arg USART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
* @retval None
*/
#define __HAL_USART_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((((uint8_t)(__INTERRUPT__)) >> 5U) == 1)? ((__HANDLE__)->Instance->CR1 &= ~ (1U << ((__INTERRUPT__) & USART_IT_MASK))): \
((((uint8_t)(__INTERRUPT__)) >> 5U) == 2)? ((__HANDLE__)->Instance->CR2 &= ~ (1U << ((__INTERRUPT__) & USART_IT_MASK))): \
((__HANDLE__)->Instance->CR3 &= ~ (1U << ((__INTERRUPT__) & USART_IT_MASK))))
/** @brief Checks whether the specified USART interrupt has occurred or not.
* @param __HANDLE__: specifies the USART Handle
* @param __IT__: specifies the USART interrupt source to check.
* This parameter can be one of the following values:
* @arg USART_IT_TXE: Transmit Data Register empty interrupt
* @arg USART_IT_TC: Transmission complete interrupt
* @arg USART_IT_RXNE: Receive Data register not empty interrupt
* @arg USART_IT_IDLE: Idle line detection interrupt
* @arg USART_IT_ORE: OverRun Error interrupt
* @arg USART_IT_NE: Noise Error interrupt
* @arg USART_IT_FE: Framing Error interrupt
* @arg USART_IT_PE: Parity Error interrupt
* @retval The new state of __IT__ (TRUE or FALSE).
*/
#define __HAL_USART_GET_IT(__HANDLE__, __IT__) ((__HANDLE__)->Instance->ISR & ((uint32_t)1 << ((__IT__)>> 0x08)))
/** @brief Checks whether the specified USART interrupt source is enabled.
* @param __HANDLE__: specifies the USART Handle.
* @param __IT__: specifies the USART interrupt source to check.
* This parameter can be one of the following values:
* @arg USART_IT_TXE: Transmit Data Register empty interrupt
* @arg USART_IT_TC: Transmission complete interrupt
* @arg USART_IT_RXNE: Receive Data register not empty interrupt
* @arg USART_IT_IDLE: Idle line detection interrupt
* @arg USART_IT_ORE: OverRun Error interrupt
* @arg USART_IT_NE: Noise Error interrupt
* @arg USART_IT_FE: Framing Error interrupt
* @arg USART_IT_PE: Parity Error interrupt
* @retval The new state of __IT__ (TRUE or FALSE).
*/
#define __HAL_USART_GET_IT_SOURCE(__HANDLE__, __IT__) ((((((uint8_t)(__IT__)) >> 5) == 1)? (__HANDLE__)->Instance->CR1:(((((uint8_t)(__IT__)) >> 5) == 2)? \
(__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & ((uint32_t)1 << \
(((uint16_t)(__IT__)) & USART_IT_MASK)))
/** @brief Clears the specified USART ISR flag, in setting the proper ICR register flag.
* @param __HANDLE__: specifies the USART Handle.
* @param __IT_CLEAR__: specifies the interrupt clear register flag that needs to be set
* to clear the corresponding interrupt
* This parameter can be one of the following values:
* @arg USART_CLEAR_PEF: Parity Error Clear Flag
* @arg USART_CLEAR_FEF: Framing Error Clear Flag
* @arg USART_CLEAR_NEF: Noise detected Clear Flag
* @arg USART_CLEAR_OREF: OverRun Error Clear Flag
* @arg USART_CLEAR_IDLEF: IDLE line detected Clear Flag
* @arg USART_CLEAR_TCF: Transmission Complete Clear Flag
* @arg USART_CLEAR_CTSF: CTS Interrupt Clear Flag
* @retval None
*/
#define __HAL_USART_CLEAR_IT(__HANDLE__, __IT_CLEAR__) ((__HANDLE__)->Instance->ICR = (uint32_t)(__IT_CLEAR__))
/** @brief Set a specific USART request flag.
* @param __HANDLE__: specifies the USART Handle.
* @param __REQ__: specifies the request flag to set
* This parameter can be one of the following values:
* @arg USART_RXDATA_FLUSH_REQUEST: Receive Data flush Request
* @arg USART_TXDATA_FLUSH_REQUEST: Transmit data flush Request
*
* @retval None
*/
#define __HAL_USART_SEND_REQ(__HANDLE__, __REQ__) ((__HANDLE__)->Instance->RQR |= (uint16_t)(__REQ__))
/** @brief Enable USART
* @param __HANDLE__: specifies the USART Handle.
* @retval None
*/
#define __HAL_USART_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE)
/** @brief Disable USART
* @param __HANDLE__: specifies the USART Handle.
* @retval None
*/
#define __HAL_USART_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)
/**
* @}
*/
/* Private macros --------------------------------------------------------*/
/** @defgroup USART_Private_Macros USART Private Macros
* @{
*/
/** @brief Check USART Baud rate
* @param BAUDRATE: Baudrate specified by the user
* The maximum Baud Rate is derived from the maximum clock on F0 (i.e. 48 MHz)
* divided by the smallest oversampling used on the USART (i.e. 8)
* @retval Test result (TRUE or FALSE)
*/
#define IS_USART_BAUDRATE(BAUDRATE) ((BAUDRATE) < 9000001)
/**
* @}
*/
/* Include USART HAL Extension module */
#include "stm32f0xx_hal_usart_ex.h"
/* Exported functions --------------------------------------------------------*/
/** @addtogroup USART_Exported_Functions USART Exported Functions
* @{
*/
/** @addtogroup USART_Exported_Functions_Group1 Initialization and de-initialization functions
* @{
*/
/* Initialization and de-initialization functions ******************************/
HAL_StatusTypeDef HAL_USART_Init(USART_HandleTypeDef *husart);
HAL_StatusTypeDef HAL_USART_DeInit(USART_HandleTypeDef *husart);
void HAL_USART_MspInit(USART_HandleTypeDef *husart);
void HAL_USART_MspDeInit(USART_HandleTypeDef *husart);
HAL_StatusTypeDef HAL_USART_CheckIdleState(USART_HandleTypeDef *husart);
/**
* @}
*/
/** @addtogroup USART_Exported_Functions_Group2 IO operation functions
* @{
*/
/* IO operation functions *******************************************************/
HAL_StatusTypeDef HAL_USART_Transmit(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_USART_Receive(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_USART_TransmitReceive(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_USART_Transmit_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size);
HAL_StatusTypeDef HAL_USART_Receive_IT(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size);
HAL_StatusTypeDef HAL_USART_TransmitReceive_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size);
HAL_StatusTypeDef HAL_USART_Transmit_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size);
HAL_StatusTypeDef HAL_USART_Receive_DMA(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size);
HAL_StatusTypeDef HAL_USART_TransmitReceive_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size);
HAL_StatusTypeDef HAL_USART_DMAPause(USART_HandleTypeDef *husart);
HAL_StatusTypeDef HAL_USART_DMAResume(USART_HandleTypeDef *husart);
HAL_StatusTypeDef HAL_USART_DMAStop(USART_HandleTypeDef *husart);
void HAL_USART_IRQHandler(USART_HandleTypeDef *husart);
void HAL_USART_TxCpltCallback(USART_HandleTypeDef *husart);
void HAL_USART_RxCpltCallback(USART_HandleTypeDef *husart);
void HAL_USART_TxHalfCpltCallback(USART_HandleTypeDef *husart);
void HAL_USART_RxHalfCpltCallback(USART_HandleTypeDef *husart);
void HAL_USART_TxRxCpltCallback(USART_HandleTypeDef *husart);
void HAL_USART_ErrorCallback(USART_HandleTypeDef *husart);
/**
* @}
*/
/* Peripheral Control functions ***********************************************/
/** @addtogroup USART_Exported_Functions_Group3 Peripheral State and Errors functions
* @{
*/
/* Peripheral State and Error functions ***************************************/
HAL_USART_StateTypeDef HAL_USART_GetState(USART_HandleTypeDef *husart);
uint32_t HAL_USART_GetError(USART_HandleTypeDef *husart);
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* __STM32F0xx_HAL_USART_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/