Filippo Casamassima
my fork
Fork of
mbed
by 
mbed official
Diff: TARGET_NUCLEO_F401RE/stm32f4xx_ll_fsmc.h
- Revision:
- 85:024bf7f99721
- Parent:
- 81:7d30d6019079
- Child:
- 90:cb3d968589d8
--- a/TARGET_NUCLEO_F401RE/stm32f4xx_ll_fsmc.h Mon May 19 18:14:09 2014 +0100
+++ b/TARGET_NUCLEO_F401RE/stm32f4xx_ll_fsmc.h Wed Jun 11 15:14:05 2014 +0100
@@ -2,8 +2,8 @@
******************************************************************************
* @file stm32f4xx_ll_fsmc.h
* @author MCD Application Team
- * @version V1.0.0
- * @date 18-February-2014
+ * @version V1.1.0RC2
+ * @date 14-May-2014
* @brief Header file of FSMC HAL module.
******************************************************************************
* @attention
@@ -62,69 +62,68 @@
#define FSMC_NAND_TypeDef FSMC_Bank2_3_TypeDef
#define FSMC_PCCARD_TypeDef FSMC_Bank4_TypeDef
-#define FSMC_NORSRAM_DEVICE FSMC_Bank1
-#define FSMC_NORSRAM_EXTENDED_DEVICE FSMC_Bank1E
-#define FSMC_NAND_DEVICE FSMC_Bank2_3
-#define FSMC_PCCARD_DEVICE FSMC_Bank4
+#define FSMC_NORSRAM_DEVICE FSMC_Bank1
+#define FSMC_NORSRAM_EXTENDED_DEVICE FSMC_Bank1E
+#define FSMC_NAND_DEVICE FSMC_Bank2_3
+#define FSMC_PCCARD_DEVICE FSMC_Bank4
/**
- * @brief FSMC_NORSRAM Configuration Structure definition
+ * @brief FSMC_NORSRAM Configuration Structure definition
*/
typedef struct
{
uint32_t NSBank; /*!< Specifies the NORSRAM memory device that will be used.
- This parameter can be a value of @ref FSMC_NORSRAM_Bank */
-
+ This parameter can be a value of @ref FSMC_NORSRAM_Bank */
+
uint32_t DataAddressMux; /*!< Specifies whether the address and data values are
multiplexed on the data bus or not.
This parameter can be a value of @ref FSMC_Data_Address_Bus_Multiplexing */
-
+
uint32_t MemoryType; /*!< Specifies the type of external memory attached to
the corresponding memory device.
This parameter can be a value of @ref FSMC_Memory_Type */
-
+
uint32_t MemoryDataWidth; /*!< Specifies the external memory device width.
This parameter can be a value of @ref FSMC_NORSRAM_Data_Width */
-
+
uint32_t BurstAccessMode; /*!< Enables or disables the burst access mode for Flash memory,
valid only with synchronous burst Flash memories.
This parameter can be a value of @ref FSMC_Burst_Access_Mode */
-
+
uint32_t WaitSignalPolarity; /*!< Specifies the wait signal polarity, valid only when accessing
the Flash memory in burst mode.
This parameter can be a value of @ref FSMC_Wait_Signal_Polarity */
-
+
uint32_t WrapMode; /*!< Enables or disables the Wrapped burst access mode for Flash
memory, valid only when accessing Flash memories in burst mode.
This parameter can be a value of @ref FSMC_Wrap_Mode */
-
+
uint32_t WaitSignalActive; /*!< Specifies if the wait signal is asserted by the memory one
clock cycle before the wait state or during the wait state,
valid only when accessing memories in burst mode.
This parameter can be a value of @ref FSMC_Wait_Timing */
-
+
uint32_t WriteOperation; /*!< Enables or disables the write operation in the selected device by the FSMC.
This parameter can be a value of @ref FSMC_Write_Operation */
-
+
uint32_t WaitSignal; /*!< Enables or disables the wait state insertion via wait
signal, valid for Flash memory access in burst mode.
This parameter can be a value of @ref FSMC_Wait_Signal */
-
+
uint32_t ExtendedMode; /*!< Enables or disables the extended mode.
This parameter can be a value of @ref FSMC_Extended_Mode */
-
+
uint32_t AsynchronousWait; /*!< Enables or disables wait signal during asynchronous transfers,
valid only with asynchronous Flash memories.
This parameter can be a value of @ref FSMC_AsynchronousWait */
-
+
uint32_t WriteBurst; /*!< Enables or disables the write burst operation.
- This parameter can be a value of @ref FSMC_Write_Burst */
+ This parameter can be a value of @ref FSMC_Write_Burst */
}FSMC_NORSRAM_InitTypeDef;
-
/**
- * @brief FSMC_NORSRAM Timing parameters structure definition
+ * @brief FSMC_NORSRAM Timing parameters structure definition
*/
typedef struct
{
@@ -132,28 +131,28 @@
the duration of the address setup time.
This parameter can be a value between Min_Data = 0 and Max_Data = 15.
@note This parameter is not used with synchronous NOR Flash memories. */
-
+
uint32_t AddressHoldTime; /*!< Defines the number of HCLK cycles to configure
the duration of the address hold time.
This parameter can be a value between Min_Data = 1 and Max_Data = 15.
@note This parameter is not used with synchronous NOR Flash memories. */
-
+
uint32_t DataSetupTime; /*!< Defines the number of HCLK cycles to configure
the duration of the data setup time.
This parameter can be a value between Min_Data = 1 and Max_Data = 255.
@note This parameter is used for SRAMs, ROMs and asynchronous multiplexed
NOR Flash memories. */
-
+
uint32_t BusTurnAroundDuration; /*!< Defines the number of HCLK cycles to configure
the duration of the bus turnaround.
This parameter can be a value between Min_Data = 0 and Max_Data = 15.
@note This parameter is only used for multiplexed NOR Flash memories. */
-
+
uint32_t CLKDivision; /*!< Defines the period of CLK clock output signal, expressed in number of
HCLK cycles. This parameter can be a value between Min_Data = 2 and Max_Data = 16.
@note This parameter is not used for asynchronous NOR Flash, SRAM or ROM
accesses. */
-
+
uint32_t DataLatency; /*!< Defines the number of memory clock cycles to issue
to the memory before getting the first data.
The parameter value depends on the memory type as shown below:
@@ -161,40 +160,40 @@
- It is don't care in asynchronous NOR, SRAM or ROM accesses
- It may assume a value between Min_Data = 2 and Max_Data = 17 in NOR Flash memories
with synchronous burst mode enable */
-
+
uint32_t AccessMode; /*!< Specifies the asynchronous access mode.
This parameter can be a value of @ref FSMC_Access_Mode */
-
+
}FSMC_NORSRAM_TimingTypeDef;
/**
- * @brief FSMC_NAND Configuration Structure definition
+ * @brief FSMC_NAND Configuration Structure definition
*/
typedef struct
{
uint32_t NandBank; /*!< Specifies the NAND memory device that will be used.
- This parameter can be a value of @ref FSMC_NAND_Bank */
-
+ This parameter can be a value of @ref FSMC_NAND_Bank */
+
uint32_t Waitfeature; /*!< Enables or disables the Wait feature for the NAND Memory device.
This parameter can be any value of @ref FSMC_Wait_feature */
-
+
uint32_t MemoryDataWidth; /*!< Specifies the external memory device width.
This parameter can be any value of @ref FSMC_NAND_Data_Width */
-
+
uint32_t EccComputation; /*!< Enables or disables the ECC computation.
This parameter can be any value of @ref FSMC_ECC */
-
+
uint32_t ECCPageSize; /*!< Defines the page size for the extended ECC.
This parameter can be any value of @ref FSMC_ECC_Page_Size */
-
+
uint32_t TCLRSetupTime; /*!< Defines the number of HCLK cycles to configure the
delay between CLE low and RE low.
This parameter can be a value between Min_Data = 0 and Max_Data = 255 */
-
+
uint32_t TARSetupTime; /*!< Defines the number of HCLK cycles to configure the
delay between ALE low and RE low.
This parameter can be a number between Min_Data = 0 and Max_Data = 255 */
-
+
}FSMC_NAND_InitTypeDef;
/**
@@ -207,45 +206,45 @@
to common/Attribute or I/O memory space (depending on
the memory space timing to be configured).
This parameter can be a value between Min_Data = 0 and Max_Data = 255 */
-
+
uint32_t WaitSetupTime; /*!< Defines the minimum number of HCLK cycles to assert the
command for NAND-Flash read or write access to
common/Attribute or I/O memory space (depending on the
memory space timing to be configured).
This parameter can be a number between Min_Data = 0 and Max_Data = 255 */
-
+
uint32_t HoldSetupTime; /*!< Defines the number of HCLK clock cycles to hold address
(and data for write access) after the command de-assertion
for NAND-Flash read or write access to common/Attribute
or I/O memory space (depending on the memory space timing
to be configured).
This parameter can be a number between Min_Data = 0 and Max_Data = 255 */
-
+
uint32_t HiZSetupTime; /*!< Defines the number of HCLK clock cycles during which the
data bus is kept in HiZ after the start of a NAND-Flash
write access to common/Attribute or I/O memory space (depending
on the memory space timing to be configured).
This parameter can be a number between Min_Data = 0 and Max_Data = 255 */
-
+
}FSMC_NAND_PCC_TimingTypeDef;
/**
- * @brief FSMC_NAND Configuration Structure definition
- */
+ * @brief FSMC_NAND Configuration Structure definition
+ */
typedef struct
{
uint32_t Waitfeature; /*!< Enables or disables the Wait feature for the PCCARD Memory device.
This parameter can be any value of @ref FSMC_Wait_feature */
-
+
uint32_t TCLRSetupTime; /*!< Defines the number of HCLK cycles to configure the
delay between CLE low and RE low.
This parameter can be a value between Min_Data = 0 and Max_Data = 255 */
-
+
uint32_t TARSetupTime; /*!< Defines the number of HCLK cycles to configure the
delay between ALE low and RE low.
This parameter can be a number between Min_Data = 0 and Max_Data = 255 */
-
-}FSMC_PCCARD_InitTypeDef;
+
+}FSMC_PCCARD_InitTypeDef;
/* Exported constants --------------------------------------------------------*/
@@ -379,7 +378,7 @@
#define FSMC_WRITE_OPERATION_ENABLE ((uint32_t)0x00001000)
#define IS_FSMC_WRITE_OPERATION(OPERATION) (((OPERATION) == FSMC_WRITE_OPERATION_DISABLE) || \
- ((OPERATION) == FSMC_WRITE_OPERATION_ENABLE))
+ ((OPERATION) == FSMC_WRITE_OPERATION_ENABLE))
/**
* @}
*/
@@ -542,7 +541,7 @@
#define FSMC_NAND_PCC_WAIT_FEATURE_ENABLE ((uint32_t)0x00000002)
#define IS_FSMC_WAIT_FEATURE(FEATURE) (((FEATURE) == FSMC_NAND_PCC_WAIT_FEATURE_DISABLE) || \
- ((FEATURE) == FSMC_NAND_PCC_WAIT_FEATURE_ENABLE))
+ ((FEATURE) == FSMC_NAND_PCC_WAIT_FEATURE_ENABLE))
/**
* @}
*/