/TARGET_K64F/TARGET_Freescale/TARGET_KPSDK_MCUS/TARGET_KPSDK_CODE/hal/adc/fsl_adc_hal.h substitute line 894 extern } by }
Fork of mbed by
TARGET_LPC11U35_501/power_api.h
- Committer:
- bogdanm
- Date:
- 2014-03-19
- Revision:
- 81:7d30d6019079
File content as of revision 81:7d30d6019079:
/**************************************************************************** * $Id:: power_api.h 6249 2011-01-25 19:23:47Z usb01267 $ * Project: NXP LPC11Uxx software example * * Description: * Power API Header File for NXP LPC11Uxx Device Series * **************************************************************************** * Software that is described herein is for illustrative purposes only * which provides customers with programming information regarding the * products. This software is supplied "AS IS" without any warranties. * NXP Semiconductors assumes no responsibility or liability for the * use of the software, conveys no license or title under any patent, * copyright, or mask work right to the product. NXP Semiconductors * reserves the right to make changes in the software without * notification. NXP Semiconductors also make no representation or * warranty that such application will be suitable for the specified * use without further testing or modification. ****************************************************************************/ #ifndef __LPC11UXX_POWER_API_H__ #define __LPC11UXX_POWER_API_H__ #ifdef __cplusplus extern "C" { #endif #define PWRROMD_PRESENT typedef struct _PWRD { void (*set_pll)(unsigned int cmd[], unsigned int resp[]); void (*set_power)(unsigned int cmd[], unsigned int resp[]); } PWRD; typedef struct _ROM { #ifdef USBROMD_PRESENT const USB * pUSBD; #else const unsigned p_usbd; #endif /* USBROMD_PRESENT */ const unsigned p_clib; const unsigned p_cand; #ifdef PWRROMD_PRESENT const PWRD * pPWRD; #else const unsigned p_pwrd; #endif /* PWRROMD_PRESENT */ const unsigned p_dev1; const unsigned p_dev2; const unsigned p_dev3; const unsigned p_dev4; } ROM; //PLL setup related definitions #define CPU_FREQ_EQU 0 //main PLL freq must be equal to the specified #define CPU_FREQ_LTE 1 //main PLL freq must be less than or equal the specified #define CPU_FREQ_GTE 2 //main PLL freq must be greater than or equal the specified #define CPU_FREQ_APPROX 3 //main PLL freq must be as close as possible the specified #define PLL_CMD_SUCCESS 0 //PLL setup successfully found #define PLL_INVALID_FREQ 1 //specified freq out of range (either input or output) #define PLL_INVALID_MODE 2 //invalid mode (see above for valid) specified #define PLL_FREQ_NOT_FOUND 3 //specified freq not found under specified conditions #define PLL_NOT_LOCKED 4 //PLL not locked => no changes to the PLL setup //power setup elated definitions #define PARAM_DEFAULT 0 //default power settings (voltage regulator, flash interface) #define PARAM_CPU_PERFORMANCE 1 //setup for maximum CPU performance (higher current, more computation) #define PARAM_EFFICIENCY 2 //balanced setting (power vs CPU performance) #define PARAM_LOW_CURRENT 3 //lowest active current, lowest CPU performance #define PARAM_CMD_SUCCESS 0 //power setting successfully found #define PARAM_INVALID_FREQ 1 //specified freq out of range (=0 or > 50 MHz) #define PARAM_INVALID_MODE 2 //specified mode not valid (see above for valid) #define MAX_CLOCK_KHZ_PARAM 50000 #ifdef __cplusplus } #endif #endif /* __LPC11UXX_POWER_API_H__ */