/TARGET_K64F/TARGET_Freescale/TARGET_KPSDK_MCUS/TARGET_KPSDK_CODE/hal/adc/fsl_adc_hal.h substitute line 894 extern } by }
Fork of mbed by
Diff: TARGET_NUCLEO_L152RE/stm32l1xx_hal_opamp.h
- Revision:
- 90:cb3d968589d8
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/TARGET_NUCLEO_L152RE/stm32l1xx_hal_opamp.h Tue Oct 28 16:40:41 2014 +0000 @@ -0,0 +1,533 @@ +/** + ****************************************************************************** + * @file stm32l1xx_hal_opamp.h + * @author MCD Application Team + * @version V1.0.0 + * @date 5-September-2014 + * @brief Header file of OPAMP HAL module. + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32L1xx_HAL_OPAMP_H +#define __STM32L1xx_HAL_OPAMP_H + +#ifdef __cplusplus + extern "C" { +#endif + +#if defined (STM32L151xCA) || defined (STM32L151xD) || defined (STM32L152xCA) || defined (STM32L152xD) || defined (STM32L162xCA) || defined (STM32L162xD) || defined (STM32L151xE) || defined (STM32L152xE) || defined (STM32L162xE) || defined (STM32L162xC) || defined (STM32L152xC) || defined (STM32L151xC) + +/* Includes ------------------------------------------------------------------*/ +#include "stm32l1xx_hal_def.h" + +/** @addtogroup STM32L1xx_HAL_Driver + * @{ + */ + +/** @addtogroup OPAMP + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ + +/** @defgroup OPAMP_Exported_Types OPAMP Exported Types + * @{ + */ +/** + * @brief OPAMP Init structure definition + */ + +typedef struct +{ + uint32_t PowerSupplyRange; /*!< Specifies the power supply range: above or under 2.4V. + This parameter must be a value of @ref OPAMP_PowerSupplyRange + Caution: This parameter is common to all OPAMP instances: a modification of this parameter for the selected OPAMP impacts the other OPAMP instances. */ + + uint32_t UserTrimming; /*!< Specifies the trimming mode + This parameter must be a value of @ref OPAMP_UserTrimming + UserTrimming is either factory or user trimming. + Caution: This parameter is common to all OPAMP instances: a modification of this parameter for the selected OPAMP impacts the other OPAMP instances. */ + + uint32_t Mode; /*!< Specifies the OPAMP mode + This parameter must be a value of @ref OPAMP_Mode + mode is either Standalone or Follower */ + + uint32_t InvertingInput; /*!< Specifies the inverting input in Standalone mode + - In Standalone mode: i.e when mode is OPAMP_STANDALONE_MODE + This parameter must be a value of @ref OPAMP_InvertingInput + InvertingInput is either VM0 or VM1 + - In Follower mode: i.e when mode is OPAMP_FOLLOWER_MODE + This parameter is Not Applicable */ + + uint32_t NonInvertingInput; /*!< Specifies the non inverting input of the opamp: + This parameter must be a value of @ref OPAMP_NonInvertingInput + NonInvertingInput is either VP0, VP1 or VP2 */ + + uint32_t PowerMode; /*!< Specifies the power mode Normal or Low-Power. + This parameter must be a value of @ref OPAMP_PowerMode */ + + uint32_t TrimmingValueP; /*!< Specifies the offset trimming value (PMOS) + i.e. when UserTrimming is OPAMP_TRIMMING_USER. + This parameter must be a number between Min_Data = 0 and Max_Data = 30 (Trimming value 31 is forbidden) */ + + uint32_t TrimmingValueN; /*!< Specifies the offset trimming value (NMOS) + i.e. when UserTrimming is OPAMP_TRIMMING_USER. + This parameter must be a number between Min_Data = 0 and Max_Data = 30 (Trimming value 31 is forbidden) */ + + uint32_t TrimmingValuePLowPower; /*!< Specifies the offset trimming value (PMOS) + i.e. when UserTrimming is OPAMP_TRIMMING_USER. + This parameter must be a number between Min_Data = 0 and Max_Data = 30 (Trimming value 31 is forbidden) */ + + uint32_t TrimmingValueNLowPower; /*!< Specifies the offset trimming value (NMOS) + i.e. when UserTrimming is OPAMP_TRIMMING_USER. + This parameter must be a number between Min_Data = 0 and Max_Data = 30 (Trimming value 31 is forbidden) */ + +}OPAMP_InitTypeDef; + +/** + * @brief HAL State structures definition + */ + +typedef enum +{ + HAL_OPAMP_STATE_RESET = 0x00000000, /*!< OPMAP is not yet Initialized */ + + HAL_OPAMP_STATE_READY = 0x00000001, /*!< OPAMP is initialized and ready for use */ + HAL_OPAMP_STATE_CALIBBUSY = 0x00000002, /*!< OPAMP is enabled in auto calibration mode */ + + HAL_OPAMP_STATE_BUSY = 0x00000004, /*!< OPAMP is enabled and running in normal mode */ + HAL_OPAMP_STATE_BUSYLOCKED = 0x00000005, /*!< OPAMP is locked + only system reset allows reconfiguring the opamp. */ + +}HAL_OPAMP_StateTypeDef; + +/** + * @brief OPAMP Handle Structure definition + */ +typedef struct +{ + OPAMP_TypeDef *Instance; /*!< OPAMP instance's registers base address */ + OPAMP_InitTypeDef Init; /*!< OPAMP required parameters */ + HAL_StatusTypeDef Status; /*!< OPAMP peripheral status */ + HAL_LockTypeDef Lock; /*!< Locking object */ + __IO HAL_OPAMP_StateTypeDef State; /*!< OPAMP communication state */ + +} OPAMP_HandleTypeDef; + +/** + * @brief OPAMP_TrimmingValueTypeDef @brief definition + */ + +typedef uint32_t OPAMP_TrimmingValueTypeDef; + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup OPAMP_Exported_Constants OPAMP Exported Constants + * @{ + */ + +/** + * OTR register Mask + */ +#define OPAMP_TRIM_VALUE_MASK OPAMP_OTR_AO1_OPT_OFFSET_TRIM_LOW + +/** + * CSR register Mask + */ +#define OPAMP_CSR_INSTANCE_OFFSET ((uint32_t) 8) /* Offset of each OPAMP instance into register CSR */ +#define OPAMP_OTR_INSTANCE_OFFSET ((uint32_t) 10) /* Offset of each OPAMP instance into register OTR */ + + +/** @defgroup OPAMP_Mode OPAMP Mode + * @{ + */ +#define OPAMP_STANDALONE_MODE ((uint32_t)0x00000000) /*!< OPAMP standalone mode */ +#define OPAMP_FOLLOWER_MODE ((uint32_t)0x00000001) /*!< OPAMP follower mode */ + +#define IS_OPAMP_FUNCTIONAL_NORMALMODE(INPUT) (((INPUT) == OPAMP_STANDALONE_MODE) || \ + ((INPUT) == OPAMP_FOLLOWER_MODE)) +/** + * @} + */ + +/** @defgroup OPAMP_NonInvertingInput OPAMP NonInvertingInput + * @{ + */ +#define OPAMP_NONINVERTINGINPUT_VP0 ((uint32_t)0x00000000) /*!< Comparator non-inverting input connected to dedicated IO pin low-leakage */ +#define OPAMP_NONINVERTINGINPUT_DAC_CH1 ((uint32_t)0x00000001) /*!< Comparator non-inverting input connected internally to DAC channel 1 */ +#define OPAMP_NONINVERTINGINPUT_DAC_CH2 ((uint32_t)0x00000002) /*!< Comparator non-inverting input connected internally to DAC channel 2. Available on OPAMP2 only. */ + +#define IS_OPAMP_NONINVERTING_INPUT(INPUT) (((INPUT) == OPAMP_NONINVERTINGINPUT_VP0) || \ + ((INPUT) == OPAMP_NONINVERTINGINPUT_DAC_CH1) || \ + ((INPUT) == OPAMP_NONINVERTINGINPUT_DAC_CH2) ) +/** + * @} + */ + +/** @defgroup OPAMP_InvertingInput OPAMP InvertingInput + * @{ + */ +#define OPAMP_INVERTINGINPUT_VM0 ((uint32_t)0x00000000) /*!< Comparator inverting input connected to dedicated IO pin low-leakage */ +#define OPAMP_INVERTINGINPUT_VM1 ((uint32_t)0x00000001) /*!< Comparator inverting input connected to alternative IO pin available on some device packages */ + +#define OPAMP_INVERTINGINPUT_VINM OPAMP_INVERTINGINPUT_VM1 /*!< Alternate name for comparator inverting input connected to alternative IO pin available on some device packages */ + +#define IOPAMP_INVERTINGINPUT_VM0 OPAMP_INVERTINGINPUT_VM0 /* For compatibility with other STM32 devices */ +#define IOPAMP_INVERTINGINPUT_VM1 OPAMP_INVERTINGINPUT_VM1 /* For compatibility with other STM32 devices */ + +#define IS_OPAMP_INVERTING_INPUT(INPUT) (((INPUT) == OPAMP_INVERTINGINPUT_VM0) || \ + ((INPUT) == OPAMP_INVERTINGINPUT_VM1) ) +/** + * @} + */ + +/** @defgroup OPAMP_PowerMode OPAMP PowerMode + * @{ + */ +#define OPAMP_POWERMODE_NORMAL ((uint32_t)0x00000000) +#define OPAMP_POWERMODE_LOWPOWER ((uint32_t)0x00000001) + +#define IS_OPAMP_POWERMODE(TRIMMING) (((TRIMMING) == OPAMP_POWERMODE_NORMAL) || \ + ((TRIMMING) == OPAMP_POWERMODE_LOWPOWER) ) +/** + * @} + */ + +/** @defgroup OPAMP_PowerSupplyRange OPAMP PowerSupplyRange + * @{ + */ +#define OPAMP_POWERSUPPLY_LOW ((uint32_t)0x00000000) /*!< Power supply range low (VDDA lower than 2.4V) */ +#define OPAMP_POWERSUPPLY_HIGH OPAMP_CSR_AOP_RANGE /*!< Power supply range high (VDDA higher than 2.4V) */ + +#define IS_OPAMP_POWER_SUPPLY_RANGE(RANGE) (((RANGE) == OPAMP_POWERSUPPLY_LOW) || \ + ((RANGE) == OPAMP_POWERSUPPLY_HIGH) ) +/** + * @} + */ + +/** @defgroup OPAMP_UserTrimming OPAMP UserTrimming + * @{ + */ +#define OPAMP_TRIMMING_FACTORY ((uint32_t)0x00000000) /*!< Factory trimming */ +#define OPAMP_TRIMMING_USER OPAMP_OTR_OT_USER /*!< User trimming */ + +#define IS_OPAMP_TRIMMING(TRIMMING) (((TRIMMING) == OPAMP_TRIMMING_FACTORY) || \ + ((TRIMMING) == OPAMP_TRIMMING_USER)) +/** + * @} + */ + +/** @defgroup OPAMP_FactoryTrimming OPAMP FactoryTrimming + * @{ + */ +#define OPAMP_FACTORYTRIMMING_DUMMY ((uint32_t)0xFFFFFFFF) /*!< Dummy value if trimming value could not be retrieved */ + +#define OPAMP_FACTORYTRIMMING_P ((uint32_t)0x00000000) /*!< Offset trimming P */ +#define OPAMP_FACTORYTRIMMING_N POSITION_VAL(OPAMP_OTR_AO1_OPT_OFFSET_TRIM_HIGH) /*!< Offset trimming N */ + +#define IS_OPAMP_FACTORYTRIMMING(TRIMMING) (((TRIMMING) == OPAMP_FACTORYTRIMMING_N) || \ + ((TRIMMING) == OPAMP_FACTORYTRIMMING_P) ) +/** + * @} + */ + +/** + * @} + */ + +/* Private constants ---------------------------------------------------------*/ +/** @defgroup OPAMP_Private_Constants OPAMP Private Constants + * @{ + */ + +/* Offset trimming time: during calibration, minimum time needed between two */ +/* steps to have 1 mV accuracy. */ +/* Refer to datasheet, electrical characteristics: parameter tOFFTRIM Typ=1ms.*/ +/* Unit: ms. */ +#define OPAMP_TRIMMING_DELAY ((uint32_t) 1) + +/** + * @} + */ + + +/* Exported macros -----------------------------------------------------------*/ + +/** @defgroup OPAMP_Private_Macro OPAMP Private Macro + * @{ + */ + +/** @brief Reset OPAMP handle state + * @param __HANDLE__: OPAMP handle. + * @retval None + */ +#define __HAL_OPAMP_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_OPAMP_STATE_RESET) + +/** + * @} + */ + + +/* Private macro -------------------------------------------------------------*/ + +/** @defgroup OPAMP_Private_Macro OPAMP Private Macro + * @{ + */ + +/** + * @brief Select the OPAMP bit OPAxPD (power-down) corresponding to the + * selected OPAMP instance. + * @param __HANDLE__: OPAMP handle + * @retval None + */ +#define __OPAMP_CSR_OPAXPD(__HANDLE__) \ + (OPAMP_CSR_OPA1PD << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) + +/** + * @brief Select the OPAMP bit S3SELx (switch 3) corresponding to the + * selected OPAMP instance. + * @param __HANDLE__: OPAMP handle + * @retval None + */ +#define __OPAMP_CSR_S3SELX(__HANDLE__) \ + (OPAMP_CSR_S3SEL1 << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) + +/** + * @brief Select the OPAMP bit S4SELx (switch 4) corresponding to the + * selected OPAMP instance. + * @param __HANDLE__: OPAMP handle + * @retval None + */ +#define __OPAMP_CSR_S4SELX(__HANDLE__) \ + (OPAMP_CSR_S4SEL1 << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) + +/** + * @brief Select the OPAMP bit S5SELx (switch 5) corresponding to the + * selected OPAMP instance. + * @param __HANDLE__: OPAMP handle + * @retval None + */ +#define __OPAMP_CSR_S5SELX(__HANDLE__) \ + (OPAMP_CSR_S5SEL1 << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) + +/** + * @brief Select the OPAMP bit S3SELx (switch 6) corresponding to the + * selected OPAMP instance. + * @param __HANDLE__: OPAMP handle + * @retval None + */ +#define __OPAMP_CSR_S6SELX(__HANDLE__) \ + (OPAMP_CSR_S6SEL1 << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) + +/** + * @brief Select the OPAMP bit OPAxCAL_L (offset calibration for differential + * pair P) corresponding to the selected OPAMP instance. + * @param __HANDLE__: OPAMP handle + * @retval None + */ +#define __OPAMP_CSR_OPAXCAL_L(__HANDLE__) \ + (OPAMP_CSR_OPA1CAL_L << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) + +/** + * @brief Select the OPAMP bit OPAxCAL_H (offset calibration for differential + * pair N) corresponding to the selected OPAMP instance. + * @param __HANDLE__: OPAMP handle + * @retval None + */ +#define __OPAMP_CSR_OPAXCAL_H(__HANDLE__) \ + (OPAMP_CSR_OPA1CAL_H << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) + +/** + * @brief Select the OPAMP bit OPAxLPM (low power mode) corresponding to the + * selected OPAMP instance. + * @param __HANDLE__: OPAMP handle + * @retval None + */ +#define __OPAMP_CSR_OPAXLPM(__HANDLE__) \ + (OPAMP_CSR_OPA1LPM << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) + +/** + * @brief Select the OPAMP bits of all switches corresponding to the + * selected OPAMP instance. + * @param __HANDLE__: OPAMP handle + * @retval None + */ +#define __OPAMP_CSR_ALL_SWITCHES(__HANDLE__) \ + ( ( ((__HANDLE__)->Instance != OPAMP2) \ + )? \ + ( \ + ((OPAMP_CSR_S3SEL1 | OPAMP_CSR_S4SEL1 | OPAMP_CSR_S5SEL1 | OPAMP_CSR_S6SEL1) << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) \ + | \ + (OPAMP_CSR_ANAWSEL1 << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__))) \ + ) \ + : \ + ( \ + ((OPAMP_CSR_S3SEL1 | OPAMP_CSR_S4SEL1 | OPAMP_CSR_S5SEL1 | OPAMP_CSR_S6SEL1) << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) \ + | \ + (OPAMP_CSR_ANAWSEL1 << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__))) \ + | \ + (OPAMP_CSR_S7SEL2) \ + ) \ + ) + +/** + * @brief Select the OPAMP bit ANAWSELx (switch SanA) corresponding to the + * selected OPAMP instance. + * @param __HANDLE__: OPAMP handle + * @retval None + */ +#define __OPAMP_CSR_ANAWSELX(__HANDLE__) \ + (OPAMP_CSR_ANAWSEL1 << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__))) + +/** + * @brief Select the OPAMP bit OPAxCALOUT in function of the selected + * OPAMP instance. + * @param __HANDLE__: OPAMP handle + * @retval None + */ +#define __OPAMP_CSR_OPAXCALOUT(__HANDLE__) \ + (OPAMP_CSR_OPA1CALOUT << (__OPAMP_INSTANCE_DECIMAL__(__HANDLE__))) + +/** + * @brief Select the OPAMP trimming bits position value (position of LSB) + * in register OPAMP_OTR or register OPAMP_LPOTR in function of the selected + * OPAMP instance and the transistors differential pair high (PMOS) or + * low (NMOS). + * @param __HANDLE__: OPAMP handle + * @param __TRIM_HIGH_LOW__: transistors differential pair high or low. + * Must be a value of @ref OPAMP_FactoryTrimming. + * @retval None + */ +#define __OPAMP_OFFSET_TRIM_BITSPOSITION(__HANDLE__, __TRIM_HIGH_LOW__) \ + ((__OPAMP_INSTANCE_DECIMAL__((__HANDLE__)) * OPAMP_OTR_INSTANCE_OFFSET) + (__TRIM_HIGH_LOW__)) + +/** + * @brief Shift the OPAMP trimming bits to register OPAMP_OTR or register + * OPAMP_LPOTR in function of the selected OPAMP instance and the transistors + * differential pair high (PMOS) or low (NMOS). + * @param __HANDLE__: OPAMP handle + * @param __TRIM_HIGH_LOW__: transistors differential pair high or low. + * Must be a value of @ref OPAMP_FactoryTrimming. + * @param __TRIMMING_VALUE__: Trimming value + * @retval None + */ +#define __OPAMP_OFFSET_TRIM_SET(__HANDLE__, __TRIM_HIGH_LOW__, __TRIMMING_VALUE__) \ + ((__TRIMMING_VALUE__) << (__OPAMP_OFFSET_TRIM_BITSPOSITION((__HANDLE__), (__TRIM_HIGH_LOW__)))) + +/** + * @brief Check that trimming value is within correct range + * @param TRIMMINGVALUE: OPAMP trimming value + * @retval None + */ +#define IS_OPAMP_TRIMMINGVALUE(TRIMMINGVALUE) ((TRIMMINGVALUE) <= 0x1E) + +/** + * @} + */ + + +/* Include OPAMP HAL Extension module */ +#include "stm32l1xx_hal_opamp_ex.h" + +/* Exported functions --------------------------------------------------------*/ + +/** @addtogroup OPAMP_Exported_Functions + * @{ + */ + +/** @addtogroup OPAMP_Exported_Functions_Group1 + * @{ + */ +/* Initialization/de-initialization functions **********************************/ +HAL_StatusTypeDef HAL_OPAMP_Init(OPAMP_HandleTypeDef *hopamp); +HAL_StatusTypeDef HAL_OPAMP_DeInit (OPAMP_HandleTypeDef *hopamp); +void HAL_OPAMP_MspInit(OPAMP_HandleTypeDef *hopamp); +void HAL_OPAMP_MspDeInit(OPAMP_HandleTypeDef *hopamp); +/** + * @} + */ + +/** @addtogroup OPAMP_Exported_Functions_Group2 + * @{ + */ +/* I/O operation functions *****************************************************/ +HAL_StatusTypeDef HAL_OPAMP_Start(OPAMP_HandleTypeDef *hopamp); +HAL_StatusTypeDef HAL_OPAMP_Stop(OPAMP_HandleTypeDef *hopamp); +HAL_StatusTypeDef HAL_OPAMP_SelfCalibrate(OPAMP_HandleTypeDef *hopamp); +OPAMP_TrimmingValueTypeDef HAL_OPAMP_GetTrimOffset (OPAMP_HandleTypeDef *hopamp, uint32_t trimmingoffset); +/** + * @} + */ + +/** @addtogroup OPAMP_Exported_Functions_Group3 + * @{ + */ +/* Peripheral Control functions ************************************************/ +HAL_StatusTypeDef HAL_OPAMP_Lock(OPAMP_HandleTypeDef *hopamp); +/** + * @} + */ + +/** @addtogroup OPAMP_Exported_Functions_Group4 + * @{ + */ +/* Peripheral State functions **************************************************/ +HAL_OPAMP_StateTypeDef HAL_OPAMP_GetState(OPAMP_HandleTypeDef *hopamp); +/** + * @} + */ + +/** + * @} + */ + + + + +/** + * @} + */ + +/** + * @} + */ + +#endif /* STM32L151xCA || STM32L151xD || STM32L152xCA || STM32L152xD || STM32L162xCA || STM32L162xD || STM32L151xE || STM32L152xE || STM32L162xE || STM32L162xC || STM32L152xC || STM32L151xC */ +#ifdef __cplusplus +} +#endif + +#endif /* __STM32L1xx_HAL_OPAMP_H */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/