frederic blanc
/TARGET_K64F/TARGET_Freescale/TARGET_KPSDK_MCUS/TARGET_KPSDK_CODE/hal/adc/fsl_adc_hal.h substitute line 894 extern } by }
Fork of
mbed
by 
mbed official
Diff: TARGET_MTS_MDOT_F405RG/stm32f4xx_hal_usart.h
- Revision:
- 92:4fc01daae5a5
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/TARGET_MTS_MDOT_F405RG/stm32f4xx_hal_usart.h Thu Nov 27 13:33:22 2014 +0000
@@ -0,0 +1,490 @@
+/**
+ ******************************************************************************
+ * @file stm32f4xx_hal_usart.h
+ * @author MCD Application Team
+ * @version V1.1.0
+ * @date 19-June-2014
+ * @brief Header file of USART HAL module.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F4xx_HAL_USART_H
+#define __STM32F4xx_HAL_USART_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f4xx_hal_def.h"
+
+/** @addtogroup STM32F4xx_HAL_Driver
+ * @{
+ */
+
+/** @addtogroup USART
+ * @{
+ */
+
+/* Exported types ------------------------------------------------------------*/
+/**
+ * @brief USART Init Structure definition
+ */
+typedef struct
+{
+ uint32_t BaudRate; /*!< This member configures the Usart communication baud rate.
+ The baud rate is computed using the following formula:
+ - IntegerDivider = ((PCLKx) / (8 * (husart->Init.BaudRate)))
+ - FractionalDivider = ((IntegerDivider - ((uint32_t) IntegerDivider)) * 8) + 0.5 */
+
+ uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame.
+ This parameter can be a value of @ref USART_Word_Length */
+
+ uint32_t StopBits; /*!< Specifies the number of stop bits transmitted.
+ This parameter can be a value of @ref USART_Stop_Bits */
+
+ uint32_t Parity; /*!< Specifies the parity mode.
+ This parameter can be a value of @ref USART_Parity
+ @note When parity is enabled, the computed parity is inserted
+ at the MSB position of the transmitted data (9th bit when
+ the word length is set to 9 data bits; 8th bit when the
+ word length is set to 8 data bits). */
+
+ uint32_t Mode; /*!< Specifies wether the Receive or Transmit mode is enabled or disabled.
+ This parameter can be a value of @ref USART_Mode */
+
+ uint32_t CLKPolarity; /*!< Specifies the steady state of the serial clock.
+ This parameter can be a value of @ref USART_Clock_Polarity */
+
+ uint32_t CLKPhase; /*!< Specifies the clock transition on which the bit capture is made.
+ This parameter can be a value of @ref USART_Clock_Phase */
+
+ uint32_t CLKLastBit; /*!< Specifies whether the clock pulse corresponding to the last transmitted
+ data bit (MSB) has to be output on the SCLK pin in synchronous mode.
+ This parameter can be a value of @ref USART_Last_Bit */
+}USART_InitTypeDef;
+
+/**
+ * @brief HAL State structures definition
+ */
+typedef enum
+{
+ HAL_USART_STATE_RESET = 0x00, /*!< Peripheral is not yet Initialized */
+ HAL_USART_STATE_READY = 0x01, /*!< Peripheral Initialized and ready for use */
+ HAL_USART_STATE_BUSY = 0x02, /*!< an internal process is ongoing */
+ HAL_USART_STATE_BUSY_TX = 0x12, /*!< Data Transmission process is ongoing */
+ HAL_USART_STATE_BUSY_RX = 0x22, /*!< Data Reception process is ongoing */
+ HAL_USART_STATE_BUSY_TX_RX = 0x32, /*!< Data Transmission Reception process is ongoing */
+ HAL_USART_STATE_TIMEOUT = 0x03, /*!< Timeout state */
+ HAL_USART_STATE_ERROR = 0x04 /*!< Error */
+}HAL_USART_StateTypeDef;
+
+/**
+ * @brief HAL USART Error Code structure definition
+ */
+typedef enum
+{
+ HAL_USART_ERROR_NONE = 0x00, /*!< No error */
+ HAL_USART_ERROR_PE = 0x01, /*!< Parity error */
+ HAL_USART_ERROR_NE = 0x02, /*!< Noise error */
+ HAL_USART_ERROR_FE = 0x04, /*!< frame error */
+ HAL_USART_ERROR_ORE = 0x08, /*!< Overrun error */
+ HAL_USART_ERROR_DMA = 0x10 /*!< DMA transfer error */
+}HAL_USART_ErrorTypeDef;
+
+/**
+ * @brief USART handle Structure definition
+ */
+typedef struct
+{
+ USART_TypeDef *Instance; /* USART registers base address */
+
+ USART_InitTypeDef Init; /* Usart communication parameters */
+
+ uint8_t *pTxBuffPtr; /* Pointer to Usart Tx transfer Buffer */
+
+ uint16_t TxXferSize; /* Usart Tx Transfer size */
+
+ __IO uint16_t TxXferCount; /* Usart Tx Transfer Counter */
+
+ uint8_t *pRxBuffPtr; /* Pointer to Usart Rx transfer Buffer */
+
+ uint16_t RxXferSize; /* Usart Rx Transfer size */
+
+ __IO uint16_t RxXferCount; /* Usart Rx Transfer Counter */
+
+ DMA_HandleTypeDef *hdmatx; /* Usart Tx DMA Handle parameters */
+
+ DMA_HandleTypeDef *hdmarx; /* Usart Rx DMA Handle parameters */
+
+ HAL_LockTypeDef Lock; /* Locking object */
+
+ __IO HAL_USART_StateTypeDef State; /* Usart communication state */
+
+ __IO HAL_USART_ErrorTypeDef ErrorCode; /* USART Error code */
+
+}USART_HandleTypeDef;
+
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup USART_Exported_Constants
+ * @{
+ */
+
+/** @defgroup USART_Word_Length
+ * @{
+ */
+#define USART_WORDLENGTH_8B ((uint32_t)0x00000000)
+#define USART_WORDLENGTH_9B ((uint32_t)USART_CR1_M)
+#define IS_USART_WORD_LENGTH(LENGTH) (((LENGTH) == USART_WORDLENGTH_8B) || \
+ ((LENGTH) == USART_WORDLENGTH_9B))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Stop_Bits
+ * @{
+ */
+#define USART_STOPBITS_1 ((uint32_t)0x00000000)
+#define USART_STOPBITS_0_5 ((uint32_t)USART_CR2_STOP_0)
+#define USART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1)
+#define USART_STOPBITS_1_5 ((uint32_t)(USART_CR2_STOP_0 | USART_CR2_STOP_1))
+#define IS_USART_STOPBITS(STOPBITS) (((STOPBITS) == USART_STOPBITS_1) || \
+ ((STOPBITS) == USART_STOPBITS_0_5) || \
+ ((STOPBITS) == USART_STOPBITS_1_5) || \
+ ((STOPBITS) == USART_STOPBITS_2))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Parity
+ * @{
+ */
+#define USART_PARITY_NONE ((uint32_t)0x00000000)
+#define USART_PARITY_EVEN ((uint32_t)USART_CR1_PCE)
+#define USART_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS))
+#define IS_USART_PARITY(PARITY) (((PARITY) == USART_PARITY_NONE) || \
+ ((PARITY) == USART_PARITY_EVEN) || \
+ ((PARITY) == USART_PARITY_ODD))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Mode
+ * @{
+ */
+#define USART_MODE_RX ((uint32_t)USART_CR1_RE)
+#define USART_MODE_TX ((uint32_t)USART_CR1_TE)
+#define USART_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE))
+#define IS_USART_MODE(MODE) ((((MODE) & (uint32_t)0xFFF3) == 0x00) && ((MODE) != (uint32_t)0x00))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Clock
+ * @{
+ */
+#define USART_CLOCK_DISABLED ((uint32_t)0x00000000)
+#define USART_CLOCK_ENABLED ((uint32_t)USART_CR2_CLKEN)
+#define IS_USART_CLOCK(CLOCK) (((CLOCK) == USART_CLOCK_DISABLED) || \
+ ((CLOCK) == USART_CLOCK_ENABLED))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Clock_Polarity
+ * @{
+ */
+#define USART_POLARITY_LOW ((uint32_t)0x00000000)
+#define USART_POLARITY_HIGH ((uint32_t)USART_CR2_CPOL)
+#define IS_USART_POLARITY(CPOL) (((CPOL) == USART_POLARITY_LOW) || ((CPOL) == USART_POLARITY_HIGH))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Clock_Phase
+ * @{
+ */
+#define USART_PHASE_1EDGE ((uint32_t)0x00000000)
+#define USART_PHASE_2EDGE ((uint32_t)USART_CR2_CPHA)
+#define IS_USART_PHASE(CPHA) (((CPHA) == USART_PHASE_1EDGE) || ((CPHA) == USART_PHASE_2EDGE))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Last_Bit
+ * @{
+ */
+#define USART_LASTBIT_DISABLE ((uint32_t)0x00000000)
+#define USART_LASTBIT_ENABLE ((uint32_t)USART_CR2_LBCL)
+#define IS_USART_LASTBIT(LASTBIT) (((LASTBIT) == USART_LASTBIT_DISABLE) || \
+ ((LASTBIT) == USART_LASTBIT_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup USART_NACK_State
+ * @{
+ */
+#define USARTNACK_ENABLED ((uint32_t)USART_CR3_NACK)
+#define USARTNACK_DISABLED ((uint32_t)0x00000000)
+#define IS_USART_NACK_STATE(NACK) (((NACK) == USARTNACK_ENABLED) || \
+ ((NACK) == USARTNACK_DISABLED))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Flags
+ * Elements values convention: 0xXXXX
+ * - 0xXXXX : Flag mask in the SR register
+ * @{
+ */
+
+#define USART_FLAG_TXE ((uint32_t)0x00000080)
+#define USART_FLAG_TC ((uint32_t)0x00000040)
+#define USART_FLAG_RXNE ((uint32_t)0x00000020)
+#define USART_FLAG_IDLE ((uint32_t)0x00000010)
+#define USART_FLAG_ORE ((uint32_t)0x00000008)
+#define USART_FLAG_NE ((uint32_t)0x00000004)
+#define USART_FLAG_FE ((uint32_t)0x00000002)
+#define USART_FLAG_PE ((uint32_t)0x00000001)
+/**
+ * @}
+ */
+
+/** @defgroup USART_Interrupt_definition
+ * Elements values convention: 0xY000XXXX
+ * - XXXX : Interrupt mask in the XX register
+ * - Y : Interrupt source register (2bits)
+ * - 01: CR1 register
+ * - 10: CR2 register
+ * - 11: CR3 register
+ *
+ * @{
+ */
+#define USART_IT_PE ((uint32_t)0x10000100)
+#define USART_IT_TXE ((uint32_t)0x10000080)
+#define USART_IT_TC ((uint32_t)0x10000040)
+#define USART_IT_RXNE ((uint32_t)0x10000020)
+#define USART_IT_IDLE ((uint32_t)0x10000010)
+
+#define USART_IT_LBD ((uint32_t)0x20000040)
+#define USART_IT_CTS ((uint32_t)0x30000400)
+
+#define USART_IT_ERR ((uint32_t)0x30000001)
+
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @brief Reset USART handle state
+ * @param __HANDLE__: specifies the USART Handle.
+ * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral.
+ * @retval None
+ */
+#define __HAL_USART_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_USART_STATE_RESET)
+
+/** @brief Checks whether the specified Smartcard flag is set or not.
+ * @param __HANDLE__: specifies the USART Handle.
+ * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral.
+ * @param __FLAG__: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg USART_FLAG_TXE: Transmit data register empty flag
+ * @arg USART_FLAG_TC: Transmission Complete flag
+ * @arg USART_FLAG_RXNE: Receive data register not empty flag
+ * @arg USART_FLAG_IDLE: Idle Line detection flag
+ * @arg USART_FLAG_ORE: OverRun Error flag
+ * @arg USART_FLAG_NE: Noise Error flag
+ * @arg USART_FLAG_FE: Framing Error flag
+ * @arg USART_FLAG_PE: Parity Error flag
+ * @retval The new state of __FLAG__ (TRUE or FALSE).
+ */
+
+#define __HAL_USART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__))
+
+/** @brief Clears the specified Smartcard pending flags.
+ * @param __HANDLE__: specifies the USART Handle.
+ * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral.
+ * @param __FLAG__: specifies the flag to check.
+ * This parameter can be any combination of the following values:
+ * @arg USART_FLAG_TC: Transmission Complete flag.
+ * @arg USART_FLAG_RXNE: Receive data register not empty flag.
+ *
+ * @note PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun
+ * error) and IDLE (Idle line detected) flags are cleared by software
+ * sequence: a read operation to USART_SR register followed by a read
+ * operation to USART_DR register.
+ * @note RXNE flag can be also cleared by a read to the USART_DR register.
+ * @note TC flag can be also cleared by software sequence: a read operation to
+ * USART_SR register followed by a write operation to USART_DR register.
+ * @note TXE flag is cleared only by a write to the USART_DR register.
+ *
+ * @retval None
+ */
+#define __HAL_USART_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR = ~(__FLAG__))
+
+/** @brief Clear the USART PE pending flag.
+ * @param __HANDLE__: specifies the USART Handle.
+ * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral.
+ * @retval None
+ */
+#define __HAL_USART_CLEAR_PEFLAG(__HANDLE__) do{(__HANDLE__)->Instance->SR;\
+ (__HANDLE__)->Instance->DR;}while(0)
+/** @brief Clear the USART FE pending flag.
+ * @param __HANDLE__: specifies the USART Handle.
+ * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral.
+ * @retval None
+ */
+#define __HAL_USART_CLEAR_FEFLAG(__HANDLE__) __HAL_USART_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief Clear the USART NE pending flag.
+ * @param __HANDLE__: specifies the USART Handle.
+ * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral.
+ * @retval None
+ */
+#define __HAL_USART_CLEAR_NEFLAG(__HANDLE__) __HAL_USART_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief Clear the UART ORE pending flag.
+ * @param __HANDLE__: specifies the USART Handle.
+ * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral.
+ * @retval None
+ */
+#define __HAL_USART_CLEAR_OREFLAG(__HANDLE__) __HAL_USART_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief Clear the USART IDLE pending flag.
+ * @param __HANDLE__: specifies the USART Handle.
+ * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral.
+ * @retval None
+ */
+#define __HAL_USART_CLEAR_IDLEFLAG(__HANDLE__) __HAL_USART_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief Enables or disables the specified Usart interrupts.
+ * @param __HANDLE__: specifies the USART Handle.
+ * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral.
+ * @param __INTERRUPT__: specifies the USART interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg USART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg USART_IT_TC: Transmission complete interrupt
+ * @arg USART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg USART_IT_IDLE: Idle line detection interrupt
+ * @arg USART_IT_PE: Parity Error interrupt
+ * @arg USART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
+ * @param NewState: new state of the specified Usart interrupt.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+#define USART_IT_MASK ((uint32_t)0x0000FFFF)
+#define __USART_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28) == 1)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & USART_IT_MASK)): \
+ (((__INTERRUPT__) >> 28) == 2)? ((__HANDLE__)->Instance->CR2 |= ((__INTERRUPT__) & USART_IT_MASK)): \
+ ((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & USART_IT_MASK)))
+#define __USART_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28) == 1)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & USART_IT_MASK)): \
+ (((__INTERRUPT__) >> 28) == 2)? ((__HANDLE__)->Instance->CR2 &= ~((__INTERRUPT__) & USART_IT_MASK)): \
+ ((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & USART_IT_MASK)))
+
+
+/** @brief Checks whether the specified Usart interrupt has occurred or not.
+ * @param __HANDLE__: specifies the USART Handle.
+ * This parameter can be USARTx where x: 1, 2, 3 or 6 to select the USART peripheral.
+ * @param __IT__: specifies the USART interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg USART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg USART_IT_TC: Transmission complete interrupt
+ * @arg USART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg USART_IT_IDLE: Idle line detection interrupt
+ * @arg USART_IT_ERR: Error interrupt
+ * @arg USART_IT_PE: Parity Error interrupt
+ * @retval The new state of __IT__ (TRUE or FALSE).
+ */
+#define __HAL_USART_GET_IT_SOURCE(__HANDLE__, __IT__) (((((__IT__) >> 28) == 1)? (__HANDLE__)->Instance->CR1:(((((uint32_t)(__IT__)) >> 28) == 2)? \
+ (__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & (((uint32_t)(__IT__)) & USART_IT_MASK))
+
+#define __USART_ENABLE(__HANDLE__) ( (__HANDLE__)->Instance->CR1 |= USART_CR1_UE)
+#define __USART_DISABLE(__HANDLE__) ( (__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)
+
+#define __DIV(_PCLK_, _BAUD_) (((_PCLK_)*25)/(4*(_BAUD_)))
+#define __DIVMANT(_PCLK_, _BAUD_) (__DIV((_PCLK_), (_BAUD_))/100)
+#define __DIVFRAQ(_PCLK_, _BAUD_) (((__DIV((_PCLK_), (_BAUD_)) - (__DIVMANT((_PCLK_), (_BAUD_)) * 100)) * 16 + 50) / 100)
+#define __USART_BRR(_PCLK_, _BAUD_) ((__DIVMANT((_PCLK_), (_BAUD_)) << 4)|(__DIVFRAQ((_PCLK_), (_BAUD_)) & 0x0F))
+
+#define IS_USART_BAUDRATE(BAUDRATE) ((BAUDRATE) < 10500001)
+
+/* Exported functions --------------------------------------------------------*/
+/* Initialization/de-initialization functions **********************************/
+HAL_StatusTypeDef HAL_USART_Init(USART_HandleTypeDef *husart);
+HAL_StatusTypeDef HAL_USART_DeInit(USART_HandleTypeDef *husart);
+void HAL_USART_MspInit(USART_HandleTypeDef *husart);
+void HAL_USART_MspDeInit(USART_HandleTypeDef *husart);
+/* IO operation functions *******************************************************/
+HAL_StatusTypeDef HAL_USART_Transmit(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_USART_Receive(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_USART_TransmitReceive(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_USART_Transmit_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size);
+HAL_StatusTypeDef HAL_USART_Receive_IT(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size);
+HAL_StatusTypeDef HAL_USART_TransmitReceive_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size);
+HAL_StatusTypeDef HAL_USART_Transmit_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size);
+HAL_StatusTypeDef HAL_USART_Receive_DMA(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size);
+HAL_StatusTypeDef HAL_USART_TransmitReceive_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size);
+HAL_StatusTypeDef HAL_USART_DMAPause(USART_HandleTypeDef *husart);
+HAL_StatusTypeDef HAL_USART_DMAResume(USART_HandleTypeDef *husart);
+HAL_StatusTypeDef HAL_USART_DMAStop(USART_HandleTypeDef *husart);
+void HAL_USART_IRQHandler(USART_HandleTypeDef *husart);
+void HAL_USART_TxCpltCallback(USART_HandleTypeDef *husart);
+void HAL_USART_TxHalfCpltCallback(USART_HandleTypeDef *husart);
+void HAL_USART_RxCpltCallback(USART_HandleTypeDef *husart);
+void HAL_USART_RxHalfCpltCallback(USART_HandleTypeDef *husart);
+void HAL_USART_TxRxCpltCallback(USART_HandleTypeDef *husart);
+void HAL_USART_ErrorCallback(USART_HandleTypeDef *husart);
+
+/* Peripheral State functions **************************************************/
+HAL_USART_StateTypeDef HAL_USART_GetState(USART_HandleTypeDef *husart);
+uint32_t HAL_USART_GetError(USART_HandleTypeDef *husart);
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F4xx_HAL_USART_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/