Diff: targets/hal/TARGET_STM/TARGET_NZ32ST1L/PinNames.h

Revision:

545:5112d5ae6723

diff -r 1af5f1c39e80 -r 5112d5ae6723 targets/hal/TARGET_STM/TARGET_NZ32ST1L/PinNames.h
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/hal/TARGET_STM/TARGET_NZ32ST1L/PinNames.h	Thu May 21 10:00:09 2015 +0100
@@ -0,0 +1,171 @@
+/* mbed Microcontroller Library
+ *******************************************************************************
+ * Copyright (c) 2015, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ *    this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ *    this list of conditions and the following disclaimer in the documentation
+ *    and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ *    may be used to endorse or promote products derived from this software
+ *    without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ */
+#ifndef MBED_PINNAMES_H
+#define MBED_PINNAMES_H
+
+#include "cmsis.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+// See stm32l0xx_hal_gpio.h and stm32l0xx_hal_gpio_ex.h for values of MODE, PUPD and AFNUM
+#define STM_PIN_DATA(MODE, PUPD, AFNUM)  ((int)(((AFNUM) << 7) | ((PUPD) << 4) | ((MODE) << 0)))
+#define STM_PIN_MODE(X)   (((X) >> 0) & 0x0F)
+#define STM_PIN_PUPD(X)   (((X) >> 4) & 0x07)
+#define STM_PIN_AFNUM(X)  (((X) >> 7) & 0x0F)
+#define STM_MODE_INPUT              (0)
+#define STM_MODE_OUTPUT_PP          (1)
+#define STM_MODE_OUTPUT_OD          (2)
+#define STM_MODE_AF_PP              (3)
+#define STM_MODE_AF_OD              (4)
+#define STM_MODE_ANALOG             (5)
+#define STM_MODE_IT_RISING          (6)
+#define STM_MODE_IT_FALLING         (7)
+#define STM_MODE_IT_RISING_FALLING  (8)
+#define STM_MODE_EVT_RISING         (9)
+#define STM_MODE_EVT_FALLING        (10)
+#define STM_MODE_EVT_RISING_FALLING (11)
+#define STM_MODE_IT_EVT_RESET       (12)
+
+// High nibble = port number (0=A, 1=B, 2=C, 3=D, 4=E, 5=F, 6=G, 7=H)
+// Low nibble  = pin number
+#define STM_PORT(X) (((uint32_t)(X) >> 4) & 0xF)
+#define STM_PIN(X)  ((uint32_t)(X) & 0xF)
+
+typedef enum {
+    PIN_INPUT,
+    PIN_OUTPUT
+} PinDirection;
+
+typedef enum {
+    PA_0  = 0x00,
+    PA_1  = 0x01,
+    PA_2  = 0x02,
+    PA_3  = 0x03,
+    PA_4  = 0x04,
+    PA_5  = 0x05,
+    PA_6  = 0x06,
+    PA_7  = 0x07,
+    PA_8  = 0x08,
+    PA_9  = 0x09,
+    PA_10 = 0x0A,
+    PA_11 = 0x0B,
+    PA_12 = 0x0C,
+    PA_13 = 0x0D,
+    PA_14 = 0x0E,
+    PA_15 = 0x0F,
+
+    PB_0  = 0x10,
+    PB_1  = 0x11,
+    PB_2  = 0x12,
+    PB_3  = 0x13,
+    PB_4  = 0x14,
+    PB_5  = 0x15,
+    PB_6  = 0x16,
+    PB_7  = 0x17,
+    PB_8  = 0x18,
+    PB_9  = 0x19,
+    PB_10 = 0x1A,
+    PB_11 = 0x1B,
+    PB_12 = 0x1C,
+    PB_13 = 0x1D,
+    PB_14 = 0x1E,
+    PB_15 = 0x1F,
+
+    PC_0  = 0x20,
+    PC_1  = 0x21,
+    PC_2  = 0x22,
+    PC_3  = 0x23,
+    PC_4  = 0x24,
+    PC_5  = 0x25,
+    PC_6  = 0x26,
+    PC_7  = 0x27,
+    PC_8  = 0x28,
+    PC_9  = 0x29,
+    PC_10 = 0x2A,
+    PC_11 = 0x2B,
+    PC_12 = 0x2C,
+    PC_13 = 0x2D,
+    PC_14 = 0x2E,
+    PC_15 = 0x2F,
+
+    PD_2  = 0x32,
+
+    PH_0  = 0x70,
+    PH_1  = 0x71,
+
+    // Generic signals namings
+    LED1        = PB_2,
+    LED2        = PB_2,
+    LED3        = PB_2,
+    LED4        = PB_2,
+    USER_BUTTON = PC_13,
+
+#if (MX_DEFAULT_SERIAL_B10_B11 == B10_B11)
+    //Use B10/B11 as default serial port
+    SERIAL_TX   = PB_10,
+    SERIAL_RX   = PB_11,
+    USBTX       = PB_10,
+    USBRX       = PB_11,
+#else
+    //Use A2/A3 as default serial port
+    SERIAL_TX   = PA_2,
+    SERIAL_RX   = PA_3,
+    USBTX       = PA_2,
+    USBRX       = PA_3,
+#endif
+
+    I2C_SCL     = PB_8,
+    I2C_SDA     = PB_9,
+    SPI_MOSI    = PA_7,
+    SPI_MISO    = PA_6,
+    SPI_SCK     = PA_5,
+    SPI_CS      = PB_6,
+    PWM_OUT     = PB_3,
+
+    // Not connected
+    NC = (int)0xFFFFFFFF,
+
+} PinName;
+
+typedef enum {
+    PullNone  = 0,
+    PullUp    = 1,
+    PullDown  = 2,
+    OpenDrain = 3,
+    PullDefault = PullNone
+} PinMode;
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif