File content as of revision 28:925794e4178b:

#include "mbed.h"
#include "rtos.h"
#include "EthernetInterface.h"
#include "ExperimentServer.h"
#include "QEI.h"
#include "BezierCurve.h"
#include "MotorShield.h" 
#include "HardwareSetup.h"
 
//#define BEZIER_ORDER_FOOT    7
#define NUM_INPUTS 12
#define NUM_OUTPUTS 6
 
#define PULSE_TO_RAD (2.0f*3.14159f / 1200.0f)
 
// Initializations
Serial pc(USBTX, USBRX);    // USB Serial Terminal
ExperimentServer server;    // Object that lets us communicate with MATLAB
Timer t;                    // Timer to measure elapsed time of experiment
Timer hold;                 // Timer to measure how long to hold clicked position

DigitalIn clicker(PB_8);
 
QEI encoderA(PE_9,PE_11, NC, 1200, QEI::X4_ENCODING);  // MOTOR A ENCODER (no index, 1200 counts/rev, Quadrature encoding)
QEI encoderB(PA_5, PB_3, NC, 1200, QEI::X4_ENCODING);  // MOTOR B ENCODER (no index, 1200 counts/rev, Quadrature encoding)
QEI encoderC(PC_6, PC_7, NC, 1200, QEI::X4_ENCODING);  // MOTOR C ENCODER (no index, 1200 counts/rev, Quadrature encoding)
QEI encoderD(PD_12, PD_13, NC, 1200, QEI::X4_ENCODING);// MOTOR D ENCODER (no index, 1200 counts/rev, Quadrature encoding)

MotorShield motorShield(24000); //initialize the motor shield with a period of 24000 ticks or ~10kHZ
Ticker currentLoop;

// Variables for q1
float current1;
float current_des1 = 0;
float prev_current_des1 = 0;
float current_int1 = 0;
float angle1;
float angle1_des;
float velocity1;
float duty_cycle1;
float angle1_init;
  
// Fixed kinematic parameters
const float l_1=.25; 
const float l_OB=.5; 

// Timing parameters
float current_control_period_us = 200.0f;     // 5kHz current control loop
float impedance_control_period_us = 1000.0f;  // 1kHz impedance control loop
float start_period, traj_period, end_period;
 
// Control parameters
float current_Kp = 4.0f;         
float current_Ki = 0.4f;           
float current_int_max = 3.0f;       
float duty_max;      
float K_xx;
float K_yy;
float K_xy;
float D_xx;
float D_xy;
float D_yy;
 
// Model parameters
float supply_voltage = 12;     // motor supply voltage
float R = 2.0f;                // motor resistance
float k_t = 0.18f;             // motor torque constant
float nu = 0.0005;             // motor viscous friction
 
// Current control interrupt function
void CurrentLoop()
{
  // This loop sets the motor voltage commands using PI current controllers with feedforward terms.
    
    //use the motor shield as follows:
    //motorShield.motorAWrite(DUTY CYCLE, DIRECTION), DIRECTION = 0 is forward, DIRECTION =1 is backwards.
        
    current1 = -(((float(motorShield.readCurrentA())/65536.0f)*30.0f)-15.0f);           // measure current
    velocity1 = encoderA.getVelocity() * PULSE_TO_RAD;                                  // measure velocity        
    float err_c1 = current_des1 - current1;                                             // current errror
    current_int1 += err_c1;                                                             // integrate error
    current_int1 = fmaxf( fminf(current_int1, current_int_max), -current_int_max);      // anti-windup
    float ff1 = R*current_des1 + k_t*velocity1;                                         // feedforward terms
    duty_cycle1 = (ff1 + current_Kp*err_c1 + current_Ki*current_int1)/supply_voltage;   // PI current controller
    
    float absDuty1 = abs(duty_cycle1);
    if (absDuty1 > duty_max) {
        duty_cycle1 *= duty_max / absDuty1;
        absDuty1 = duty_max;
    }    
    if (duty_cycle1 < 0) { // backwards
        motorShield.motorAWrite(absDuty1, 1);
    } else { // forwards
        motorShield.motorAWrite(absDuty1, 0);
    }             
    prev_current_des1 = current_des1; 
    
}
 
int main (void)
{
    
    // Object for 7th order Cartesian foo//t trajectory
//    BezierCurve rDesFoot_bez(2,BEZIER_ORDER_FOOT);
    
    // Link the terminal with our server and start it up
    server.attachTerminal(pc);
    server.init();
    
    // Continually get input from MATLAB and run experiments
    float input_params[NUM_INPUTS];
    pc.printf("%f",input_params[0]);
    
    while(1) {
        
        // If there are new inputs, this code will run
        if (server.getParams(input_params,NUM_INPUTS)) {
            
                        
            // Get inputs from MATLAB          
            start_period                = input_params[0];    // First buffer time, before trajectory
            traj_period                 = input_params[1];    // Trajectory time/length
            end_period                  = input_params[2];    // Second buffer time, after trajectory
    
            angle1_init                 = input_params[3];    // Initial angle for q1 (rad)
            angle1_des                  = input_params[4];
 
            K_xx                        = input_params[5];    // Foot stiffness N/m
            K_yy                        = input_params[6];    // Foot stiffness N/m
            K_xy                        = input_params[7];    // Foot stiffness N/m
            D_xx                        = input_params[8];    // Foot damping N/(m/s)
            D_yy                        = input_params[9];    // Foot damping N/(m/s)
            D_xy                        = input_params[10];   // Foot damping N/(m/s)
            duty_max                    = input_params[11];   // Maximum duty factor
            
            float th1_des = angle1_init;
          
            // Get foot trajectory points
//            float foot_pts[2*(BEZIER_ORDER_FOOT+1)];
//            for(int i = 0; i<2*(BEZIER_ORDER_FOOT+1);i++) {
//              foot_pts[i] = input_params[12+i];    
//            }
//            rDesFoot_bez.setPoints(foot_pts);
            
            // Attach current loop interrupt
            currentLoop.attach_us(CurrentLoop,current_control_period_us);
                        
            // Setup experiment
            t.reset();
            t.start();
            encoderA.reset();
            encoderB.reset();
            encoderC.reset();
            encoderD.reset();
 
            motorShield.motorAWrite(0, 0); //turn motor A off
                         
            // Run experiment
            while( t.read() < start_period + traj_period + end_period) { 
                 
                // Read encoders to get motor states
                angle1 = encoderA.getPulses() *PULSE_TO_RAD + angle1_init;       
                velocity1 = encoderA.getVelocity() * PULSE_TO_RAD;                     
                
                const float th1 = angle1;
                const float dth1= velocity1;

                // Calculate the Jacobian
//                float Jx_th1 = l_AC*cos(th1+th2)+l_DE*cos(th1)+l_OB*cos(th1);
//                float Jx_th2 = l_AC*cos(th1+th2);
//                float Jy_th1 = l_AC*sin(th1+th2)+l_DE*sin(th1)+l_OB*sin(th1);
//                float Jy_th2 = l_AC*sin(th1+th2);
                                
                // Calculate the forward kinematics (position and velocity)
               // float xFoot = l_AC*sin(th1+th2)+l_DE*sin(th1)+l_OB*sin(th1);
//                float yFoot = -l_AC*cos(th1+th2)-l_DE*cos(th1)-l_OB*cos(th1);
//                float dxFoot = velocity1*(l_AC*cos(th1+th2)+l_DE*cos(th1)+l_OB*cos(th1))+velocity2*l_AC*cos(th1+th2);
//                float dyFoot = velocity1*(l_AC*sin(th1+th2)+l_DE*sin(th1)+l_OB*sin(th1))+velocity2*l_AC*sin(th1+th2);

                // Set gains based on buffer and traj times, then calculate desired x,y from Bezier trajectory at current time if necessary
                float teff  = 0;
                float vMult = 0;
                if( t < start_period) {
                    if (K_xx > 0 || K_yy > 0) {
                        K_xx = 50; // for joint space control, set this to 1; for Cartesian space control, set this to 50
                        K_yy = 50; // for joint space control, set this to 1; for Cartesian space control, set this to 50
                        D_xx = 2;  // for joint space control, set this to 0.1; for Cartesian space control, set this to 2
                        D_yy = 2;  // for joint space control, set this to 0.1; for Cartesian space control, set this to 2
                        K_xy = 0;
                        D_xy = 0;
                    }
                    teff = 0;
                }
                else if (t < start_period + traj_period)
                {
                    K_xx = input_params[5];  // Foot stiffness N/m
                    K_yy = input_params[6];  // Foot stiffness N/m
                    K_xy = input_params[7];  // Foot stiffness N/m
                    D_xx = input_params[8];  // Foot damping N/(m/s)
                    D_yy = input_params[9];  // Foot damping N/(m/s)
                    D_xy = input_params[10]; // Foot damping N/(m/s)
                    teff = (t-start_period);
                    vMult = 1;
                }
                else
                {
                    teff = traj_period;
                    vMult = 0;
                }
                
                // Get desired foot positions and velocities
//                float rDesFoot[2] , vDesFoot[2];
//                rDesFoot_bez.evaluate(teff/traj_period,rDesFoot);
//                rDesFoot_bez.evaluateDerivative(teff/traj_period,vDesFoot);
//                vDesFoot[0]/=traj_period;
//                vDesFoot[1]/=traj_period;
//                vDesFoot[0]*=vMult;
//                vDesFoot[1]*=vMult;
//                
          //      // Calculate the inverse kinematics (joint positions and velocities) for desired joint angles              
//                float xFoot_inv = -rDesFoot[0];
//                float yFoot_inv = rDesFoot[1];                
//                float l_OE = sqrt( (pow(xFoot_inv,2) + pow(yFoot_inv,2)) );
//                float alpha = abs(acos( (pow(l_OE,2) - pow(l_AC,2) - pow((l_OB+l_DE),2))/(-2.0f*l_AC*(l_OB+l_DE)) ));
//                float th2_des = -(3.14159f - alpha); 
//                float th1_des = -((3.14159f/2.0f) + atan2(yFoot_inv,xFoot_inv) - abs(asin( (l_AC/l_OE)*sin(alpha) )));
                
//                float dd = (Jx_th1*Jy_th2 - Jx_th2*Jy_th1);
//                float dth1_des = (1.0f/dd) * (  Jy_th2*vDesFoot[0] - Jx_th2*vDesFoot[1] );
//                float dth2_des = (1.0f/dd) * ( -Jy_th1*vDesFoot[0] + Jx_th1*vDesFoot[1] );
        

//                 Set desired currents             
//                current_des1 =  (-K_xx*(angle1)-D_xx*(velocity1))/k_t;    
//                while (hold.read() == 0 | hold.read() > 2){
//                    if(clicker.read() == 0) {
//                            th1_des = angle1_init;
//                        }
//                    else {
//                            th1_des = angle1_des;
//                            hold.start();
//                        }     
//                }
                th1_des = angle1_des;
                        
                // Joint impedance
                // sub Kxx for K1, Dxx for D1, Kyy for K2, Dyy for D2
                // Note: Be careful with signs now that you have non-zero desired angles!
                // Your equations should be of the form i_d = K1*(q1_d - q1) + D1*(dq1_d - dq1)
                current_des1 = (K_xx*(th1_des-angle1))/k_t;     
//                current_des1 = (K_xx*(th1_des-angle1)+D_xx*(dth1_des-velocity1))/k_t;                                                         
                           
                // Cartesian impedance  
                // Note: As with the joint space laws, be careful with signs!             
//                current_des1 = t1/k_t;          
                
                
                // Form output to send to MATLAB     
                float output_data[NUM_OUTPUTS];
                // current time
                output_data[0] = t.read();
                // motor 1 state
                output_data[1] = angle1;
                output_data[2] = velocity1;  
                output_data[3] = current1;
                output_data[4] = current_des1;
                output_data[5] = duty_cycle1;

                // foot state
//                output_data[11] = xFoot;
//                output_data[12] = yFoot;
//                output_data[13] = dxFoot;
//                output_data[14] = dyFoot;
//                output_data[15] = rDesFoot[0];
//                output_data[16] = rDesFoot[1];
//                output_data[17] = vDesFoot[0];
//                output_data[18] = vDesFoot[1];
                
                // Send data to MATLAB
                server.sendData(output_data,NUM_OUTPUTS);

                wait_us(impedance_control_period_us);   
            }
            
            // Cleanup after experiment
            server.setExperimentComplete();
            currentLoop.detach();
            motorShield.motorAWrite(0, 0); //turn motor A off
        
        } // end if
        
    } // end while
    
} // end main