erez i
version_2.0
Dependents: cc3000_ping_demo_try_2
Fork of
mbed
by 
mbed official
Diff: TARGET_NUCLEO_L152RE/stm32l1xx_usart.h
- Revision:
- 77:869cf507173a
- Child:
- 81:7d30d6019079
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/TARGET_NUCLEO_L152RE/stm32l1xx_usart.h Fri Feb 14 14:36:43 2014 +0000
@@ -0,0 +1,427 @@
+/**
+ ******************************************************************************
+ * @file stm32l1xx_usart.h
+ * @author MCD Application Team
+ * @version V1.3.0
+ * @date 31-January-2014
+ * @brief This file contains all the functions prototypes for the USART
+ * firmware library.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT 2014 STMicroelectronics</center></h2>
+ *
+ * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
+ * You may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at:
+ *
+ * http://www.st.com/software_license_agreement_liberty_v2
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L1xx_USART_H
+#define __STM32L1xx_USART_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l1xx.h"
+
+/** @addtogroup STM32L1xx_StdPeriph_Driver
+ * @{
+ */
+
+/** @addtogroup USART
+ * @{
+ */
+
+/* Exported types ------------------------------------------------------------*/
+
+/**
+ * @brief USART Init Structure definition
+ */
+
+typedef struct
+{
+ uint32_t USART_BaudRate; /*!< This member configures the USART communication baud rate.
+ The baud rate is computed using the following formula:
+ - IntegerDivider = ((PCLKx) / (8 * (OVR8+1) * (USART_InitStruct->USART_BaudRate)))
+ - FractionalDivider = ((IntegerDivider - ((u32) IntegerDivider)) * 8 * (OVR8+1)) + 0.5
+ Where OVR8 is the "oversampling by 8 mode" configuration bit in the CR1 register. */
+
+ uint16_t USART_WordLength; /*!< Specifies the number of data bits transmitted or received in a frame.
+ This parameter can be a value of @ref USART_Word_Length */
+
+ uint16_t USART_StopBits; /*!< Specifies the number of stop bits transmitted.
+ This parameter can be a value of @ref USART_Stop_Bits */
+
+ uint16_t USART_Parity; /*!< Specifies the parity mode.
+ This parameter can be a value of @ref USART_Parity
+ @note When parity is enabled, the computed parity is inserted
+ at the MSB position of the transmitted data (9th bit when
+ the word length is set to 9 data bits; 8th bit when the
+ word length is set to 8 data bits). */
+
+ uint16_t USART_Mode; /*!< Specifies wether the Receive or Transmit mode is enabled or disabled.
+ This parameter can be a value of @ref USART_Mode */
+
+ uint16_t USART_HardwareFlowControl; /*!< Specifies wether the hardware flow control mode is enabled
+ or disabled.
+ This parameter can be a value of @ref USART_Hardware_Flow_Control */
+} USART_InitTypeDef;
+
+/**
+ * @brief USART Clock Init Structure definition
+ */
+
+typedef struct
+{
+
+ uint16_t USART_Clock; /*!< Specifies whether the USART clock is enabled or disabled.
+ This parameter can be a value of @ref USART_Clock */
+
+ uint16_t USART_CPOL; /*!< Specifies the steady state of the serial clock.
+ This parameter can be a value of @ref USART_Clock_Polarity */
+
+ uint16_t USART_CPHA; /*!< Specifies the clock transition on which the bit capture is made.
+ This parameter can be a value of @ref USART_Clock_Phase */
+
+ uint16_t USART_LastBit; /*!< Specifies whether the clock pulse corresponding to the last transmitted
+ data bit (MSB) has to be output on the SCLK pin in synchronous mode.
+ This parameter can be a value of @ref USART_Last_Bit */
+} USART_ClockInitTypeDef;
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup USART_Exported_Constants
+ * @{
+ */
+
+#define IS_USART_ALL_PERIPH(PERIPH) (((PERIPH) == USART1) || \
+ ((PERIPH) == USART2) || \
+ ((PERIPH) == USART3) || \
+ ((PERIPH) == UART4) || \
+ ((PERIPH) == UART5))
+
+#define IS_USART_123_PERIPH(PERIPH) (((PERIPH) == USART1) || \
+ ((PERIPH) == USART2) || \
+ ((PERIPH) == USART3))
+
+/** @defgroup USART_Word_Length
+ * @{
+ */
+
+#define USART_WordLength_8b ((uint16_t)0x0000)
+#define USART_WordLength_9b ((uint16_t)0x1000)
+
+#define IS_USART_WORD_LENGTH(LENGTH) (((LENGTH) == USART_WordLength_8b) || \
+ ((LENGTH) == USART_WordLength_9b))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Stop_Bits
+ * @{
+ */
+
+#define USART_StopBits_1 ((uint16_t)0x0000)
+#define USART_StopBits_0_5 ((uint16_t)0x1000)
+#define USART_StopBits_2 ((uint16_t)0x2000)
+#define USART_StopBits_1_5 ((uint16_t)0x3000)
+#define IS_USART_STOPBITS(STOPBITS) (((STOPBITS) == USART_StopBits_1) || \
+ ((STOPBITS) == USART_StopBits_0_5) || \
+ ((STOPBITS) == USART_StopBits_2) || \
+ ((STOPBITS) == USART_StopBits_1_5))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Parity
+ * @{
+ */
+
+#define USART_Parity_No ((uint16_t)0x0000)
+#define USART_Parity_Even ((uint16_t)0x0400)
+#define USART_Parity_Odd ((uint16_t)0x0600)
+#define IS_USART_PARITY(PARITY) (((PARITY) == USART_Parity_No) || \
+ ((PARITY) == USART_Parity_Even) || \
+ ((PARITY) == USART_Parity_Odd))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Mode
+ * @{
+ */
+
+#define USART_Mode_Rx ((uint16_t)0x0004)
+#define USART_Mode_Tx ((uint16_t)0x0008)
+#define IS_USART_MODE(MODE) ((((MODE) & (uint16_t)0xFFF3) == 0x00) && ((MODE) != (uint16_t)0x00))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Hardware_Flow_Control
+ * @{
+ */
+#define USART_HardwareFlowControl_None ((uint16_t)0x0000)
+#define USART_HardwareFlowControl_RTS ((uint16_t)0x0100)
+#define USART_HardwareFlowControl_CTS ((uint16_t)0x0200)
+#define USART_HardwareFlowControl_RTS_CTS ((uint16_t)0x0300)
+#define IS_USART_HARDWARE_FLOW_CONTROL(CONTROL)\
+ (((CONTROL) == USART_HardwareFlowControl_None) || \
+ ((CONTROL) == USART_HardwareFlowControl_RTS) || \
+ ((CONTROL) == USART_HardwareFlowControl_CTS) || \
+ ((CONTROL) == USART_HardwareFlowControl_RTS_CTS))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Clock
+ * @{
+ */
+#define USART_Clock_Disable ((uint16_t)0x0000)
+#define USART_Clock_Enable ((uint16_t)0x0800)
+#define IS_USART_CLOCK(CLOCK) (((CLOCK) == USART_Clock_Disable) || \
+ ((CLOCK) == USART_Clock_Enable))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Clock_Polarity
+ * @{
+ */
+
+#define USART_CPOL_Low ((uint16_t)0x0000)
+#define USART_CPOL_High ((uint16_t)0x0400)
+#define IS_USART_CPOL(CPOL) (((CPOL) == USART_CPOL_Low) || ((CPOL) == USART_CPOL_High))
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Clock_Phase
+ * @{
+ */
+
+#define USART_CPHA_1Edge ((uint16_t)0x0000)
+#define USART_CPHA_2Edge ((uint16_t)0x0200)
+#define IS_USART_CPHA(CPHA) (((CPHA) == USART_CPHA_1Edge) || ((CPHA) == USART_CPHA_2Edge))
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_Last_Bit
+ * @{
+ */
+
+#define USART_LastBit_Disable ((uint16_t)0x0000)
+#define USART_LastBit_Enable ((uint16_t)0x0100)
+#define IS_USART_LASTBIT(LASTBIT) (((LASTBIT) == USART_LastBit_Disable) || \
+ ((LASTBIT) == USART_LastBit_Enable))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Interrupt_definition
+ * @{
+ */
+
+#define USART_IT_PE ((uint16_t)0x0028)
+#define USART_IT_TXE ((uint16_t)0x0727)
+#define USART_IT_TC ((uint16_t)0x0626)
+#define USART_IT_RXNE ((uint16_t)0x0525)
+#define USART_IT_IDLE ((uint16_t)0x0424)
+#define USART_IT_LBD ((uint16_t)0x0846)
+#define USART_IT_ORE_RX ((uint16_t)0x0325) /* In case interrupt is generated if the RXNEIE bit is set */
+#define USART_IT_CTS ((uint16_t)0x096A)
+#define USART_IT_ERR ((uint16_t)0x0060)
+#define USART_IT_ORE_ER ((uint16_t)0x0360) /* In case interrupt is generated if the EIE bit is set */
+#define USART_IT_NE ((uint16_t)0x0260)
+#define USART_IT_FE ((uint16_t)0x0160)
+
+/** @defgroup USART_Legacy
+ * @{
+ */
+#define USART_IT_ORE USART_IT_ORE_ER
+/**
+ * @}
+ */
+
+#define IS_USART_CONFIG_IT(IT) (((IT) == USART_IT_PE) || ((IT) == USART_IT_TXE) || \
+ ((IT) == USART_IT_TC) || ((IT) == USART_IT_RXNE) || \
+ ((IT) == USART_IT_IDLE) || ((IT) == USART_IT_LBD) || \
+ ((IT) == USART_IT_CTS) || ((IT) == USART_IT_ERR))
+#define IS_USART_GET_IT(IT) (((IT) == USART_IT_PE) || ((IT) == USART_IT_TXE) || \
+ ((IT) == USART_IT_TC) || ((IT) == USART_IT_RXNE) || \
+ ((IT) == USART_IT_IDLE) || ((IT) == USART_IT_LBD) || \
+ ((IT) == USART_IT_CTS) || ((IT) == USART_IT_ORE_RX) || \
+ ((IT) == USART_IT_ORE_ER) || ((IT) == USART_IT_NE) || \
+ ((IT) == USART_IT_FE))
+#define IS_USART_CLEAR_IT(IT) (((IT) == USART_IT_TC) || ((IT) == USART_IT_RXNE) || \
+ ((IT) == USART_IT_LBD) || ((IT) == USART_IT_CTS))
+/**
+ * @}
+ */
+
+/** @defgroup USART_DMA_Requests
+ * @{
+ */
+
+#define USART_DMAReq_Tx ((uint16_t)0x0080)
+#define USART_DMAReq_Rx ((uint16_t)0x0040)
+#define IS_USART_DMAREQ(DMAREQ) ((((DMAREQ) & (uint16_t)0xFF3F) == 0x00) && ((DMAREQ) != (uint16_t)0x00))
+
+/**
+ * @}
+ */
+
+/** @defgroup USART_WakeUp_methods
+ * @{
+ */
+
+#define USART_WakeUp_IdleLine ((uint16_t)0x0000)
+#define USART_WakeUp_AddressMark ((uint16_t)0x0800)
+#define IS_USART_WAKEUP(WAKEUP) (((WAKEUP) == USART_WakeUp_IdleLine) || \
+ ((WAKEUP) == USART_WakeUp_AddressMark))
+/**
+ * @}
+ */
+
+/** @defgroup USART_LIN_Break_Detection_Length
+ * @{
+ */
+
+#define USART_LINBreakDetectLength_10b ((uint16_t)0x0000)
+#define USART_LINBreakDetectLength_11b ((uint16_t)0x0020)
+#define IS_USART_LIN_BREAK_DETECT_LENGTH(LENGTH) \
+ (((LENGTH) == USART_LINBreakDetectLength_10b) || \
+ ((LENGTH) == USART_LINBreakDetectLength_11b))
+/**
+ * @}
+ */
+
+/** @defgroup USART_IrDA_Low_Power
+ * @{
+ */
+
+#define USART_IrDAMode_LowPower ((uint16_t)0x0004)
+#define USART_IrDAMode_Normal ((uint16_t)0x0000)
+#define IS_USART_IRDA_MODE(MODE) (((MODE) == USART_IrDAMode_LowPower) || \
+ ((MODE) == USART_IrDAMode_Normal))
+/**
+ * @}
+ */
+
+/** @defgroup USART_Flags
+ * @{
+ */
+
+#define USART_FLAG_CTS ((uint16_t)0x0200)
+#define USART_FLAG_LBD ((uint16_t)0x0100)
+#define USART_FLAG_TXE ((uint16_t)0x0080)
+#define USART_FLAG_TC ((uint16_t)0x0040)
+#define USART_FLAG_RXNE ((uint16_t)0x0020)
+#define USART_FLAG_IDLE ((uint16_t)0x0010)
+#define USART_FLAG_ORE ((uint16_t)0x0008)
+#define USART_FLAG_NE ((uint16_t)0x0004)
+#define USART_FLAG_FE ((uint16_t)0x0002)
+#define USART_FLAG_PE ((uint16_t)0x0001)
+#define IS_USART_FLAG(FLAG) (((FLAG) == USART_FLAG_PE) || ((FLAG) == USART_FLAG_TXE) || \
+ ((FLAG) == USART_FLAG_TC) || ((FLAG) == USART_FLAG_RXNE) || \
+ ((FLAG) == USART_FLAG_IDLE) || ((FLAG) == USART_FLAG_LBD) || \
+ ((FLAG) == USART_FLAG_CTS) || ((FLAG) == USART_FLAG_ORE) || \
+ ((FLAG) == USART_FLAG_NE) || ((FLAG) == USART_FLAG_FE))
+
+#define IS_USART_CLEAR_FLAG(FLAG) ((((FLAG) & (uint16_t)0xFC9F) == 0x00) && ((FLAG) != (uint16_t)0x00))
+
+#define IS_USART_BAUDRATE(BAUDRATE) (((BAUDRATE) > 0) && ((BAUDRATE) < 0x003D0901))
+#define IS_USART_ADDRESS(ADDRESS) ((ADDRESS) <= 0xF)
+#define IS_USART_DATA(DATA) ((DATA) <= 0x1FF)
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Exported macro ------------------------------------------------------------*/
+/* Exported functions ------------------------------------------------------- */
+
+/* Function used to set the USART configuration to the default reset state ***/
+void USART_DeInit(USART_TypeDef* USARTx);
+
+/* Initialization and Configuration functions *********************************/
+void USART_Init(USART_TypeDef* USARTx, USART_InitTypeDef* USART_InitStruct);
+void USART_StructInit(USART_InitTypeDef* USART_InitStruct);
+void USART_ClockInit(USART_TypeDef* USARTx, USART_ClockInitTypeDef* USART_ClockInitStruct);
+void USART_ClockStructInit(USART_ClockInitTypeDef* USART_ClockInitStruct);
+void USART_Cmd(USART_TypeDef* USARTx, FunctionalState NewState);
+void USART_SetPrescaler(USART_TypeDef* USARTx, uint8_t USART_Prescaler);
+void USART_OverSampling8Cmd(USART_TypeDef* USARTx, FunctionalState NewState);
+void USART_OneBitMethodCmd(USART_TypeDef* USARTx, FunctionalState NewState);
+
+/* Data transfers functions ***************************************************/
+void USART_SendData(USART_TypeDef* USARTx, uint16_t Data);
+uint16_t USART_ReceiveData(USART_TypeDef* USARTx);
+
+/* Multi-Processor Communication functions ************************************/
+void USART_SetAddress(USART_TypeDef* USARTx, uint8_t USART_Address);
+void USART_WakeUpConfig(USART_TypeDef* USARTx, uint16_t USART_WakeUp);
+void USART_ReceiverWakeUpCmd(USART_TypeDef* USARTx, FunctionalState NewState);
+
+/* LIN mode functions *********************************************************/
+void USART_LINBreakDetectLengthConfig(USART_TypeDef* USARTx, uint16_t USART_LINBreakDetectLength);
+void USART_LINCmd(USART_TypeDef* USARTx, FunctionalState NewState);
+void USART_SendBreak(USART_TypeDef* USARTx);
+
+/* Half-duplex mode function **************************************************/
+void USART_HalfDuplexCmd(USART_TypeDef* USARTx, FunctionalState NewState);
+
+/* Smartcard mode functions ***************************************************/
+void USART_SmartCardCmd(USART_TypeDef* USARTx, FunctionalState NewState);
+void USART_SmartCardNACKCmd(USART_TypeDef* USARTx, FunctionalState NewState);
+void USART_SetGuardTime(USART_TypeDef* USARTx, uint8_t USART_GuardTime);
+
+/* IrDA mode functions ********************************************************/
+void USART_IrDAConfig(USART_TypeDef* USARTx, uint16_t USART_IrDAMode);
+void USART_IrDACmd(USART_TypeDef* USARTx, FunctionalState NewState);
+
+/* DMA transfers management functions *****************************************/
+void USART_DMACmd(USART_TypeDef* USARTx, uint16_t USART_DMAReq, FunctionalState NewState);
+
+/* Interrupts and flags management functions **********************************/
+void USART_ITConfig(USART_TypeDef* USARTx, uint16_t USART_IT, FunctionalState NewState);
+FlagStatus USART_GetFlagStatus(USART_TypeDef* USARTx, uint16_t USART_FLAG);
+void USART_ClearFlag(USART_TypeDef* USARTx, uint16_t USART_FLAG);
+ITStatus USART_GetITStatus(USART_TypeDef* USARTx, uint16_t USART_IT);
+void USART_ClearITPendingBit(USART_TypeDef* USARTx, uint16_t USART_IT);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32L1xx_USART_H */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/