Elijah Orr
/
mbed-renbed
Important changes to repositories hosted on mbed.com
Mbed hosted mercurial repositories are deprecated and are due to be permanently deleted in July 2026.
To keep a copy of this software download the repository Zip archive or clone locally using Mercurial.
It is also possible to export all your personal repositories from the account settings page.
Dependents: 1-RenBuggyTimed RenBED_RGB RenBED_RGB_PWM RenBED_RGB
Fork of
mbed
by 
mbed official
Diff: TARGET_DISCO_F746NG/stm32f7xx_hal_rcc.h
- Revision:
- 116:c0f6e94411f5
- Parent:
- 107:4f6c30876dfa
diff -r 87f2f5183dfb -r c0f6e94411f5 TARGET_DISCO_F746NG/stm32f7xx_hal_rcc.h
--- a/TARGET_DISCO_F746NG/stm32f7xx_hal_rcc.h Wed Mar 02 09:58:28 2016 +0100
+++ b/TARGET_DISCO_F746NG/stm32f7xx_hal_rcc.h Tue Mar 15 14:34:00 2016 +0000
@@ -2,8 +2,8 @@
******************************************************************************
* @file stm32f7xx_hal_rcc.h
* @author MCD Application Team
- * @version V1.0.1
- * @date 25-June-2015
+ * @version V1.0.4
+ * @date 09-December-2015
* @brief Header file of RCC HAL module.
******************************************************************************
* @attention
@@ -75,7 +75,7 @@
This parameter must be a number between Min_Data = 2 and Max_Data = 63 */
uint32_t PLLN; /*!< PLLN: Multiplication factor for PLL VCO output clock.
- This parameter must be a number between Min_Data = 192 and Max_Data = 432 */
+ This parameter must be a number between Min_Data = 100 and Max_Data = 432 */
uint32_t PLLP; /*!< PLLP: Division factor for main system clock (SYSCLK).
This parameter must be a value of @ref RCC_PLLP_Clock_Divider */
@@ -442,7 +442,7 @@
* @{
*/
#define __HAL_RCC_CRC_CLK_ENABLE() do { \
- __IO uint32_t tmpreg; \
+ __IO uint32_t tmpreg = 0x00; \
SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
@@ -450,7 +450,7 @@
} while(0)
#define __HAL_RCC_DMA1_CLK_ENABLE() do { \
- __IO uint32_t tmpreg; \
+ __IO uint32_t tmpreg = 0x00; \
SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN);\
@@ -472,7 +472,7 @@
* @{
*/
#define __HAL_RCC_WWDG_CLK_ENABLE() do { \
- __IO uint32_t tmpreg; \
+ __IO uint32_t tmpreg = 0x00; \
SET_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\
@@ -480,7 +480,7 @@
} while(0)
#define __HAL_RCC_PWR_CLK_ENABLE() do { \
- __IO uint32_t tmpreg; \
+ __IO uint32_t tmpreg = 0x00; \
SET_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\
@@ -501,7 +501,7 @@
* @{
*/
#define __HAL_RCC_SYSCFG_CLK_ENABLE() do { \
- __IO uint32_t tmpreg; \
+ __IO uint32_t tmpreg = 0x00; \
SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN);\
/* Delay after an RCC peripheral clock enabling */ \
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN);\
@@ -907,9 +907,9 @@
* frequency ranges from 1 to 2 MHz. It is recommended to select a frequency
* of 2 MHz to limit PLL jitter.
* @param __PLLN__: specifies the multiplication factor for PLL VCO output clock
- * This parameter must be a number between Min_Data = 192 and Max_Data = 432.
+ * This parameter must be a number between Min_Data = 100 and Max_Data = 432.
* @note You have to set the PLLN parameter correctly to ensure that the VCO
- * output frequency is between 192 and 432 MHz.
+ * output frequency is between 100 and 432 MHz.
* @param __PLLP__: specifies the division factor for main system clock (SYSCLK)
* This parameter must be a number in the range {2, 4, 6, or 8}.
* @note You have to set the PLLP parameter correctly to not exceed 216 MHz on
@@ -963,8 +963,8 @@
* used as I2S clock source.
*/
#define __HAL_RCC_I2S_CONFIG(__SOURCE__) do {RCC->CFGR &= ~(RCC_CFGR_I2SSRC); \
- RCC->CFGR |= (__SOURCE__); \
- }while(0)
+ RCC->CFGR |= (__SOURCE__); \
+ }while(0)
/** @brief Macros to enable or disable the PLLI2S.
* @note The PLLI2S is disabled by hardware when entering STOP and STANDBY modes.
@@ -1024,7 +1024,52 @@
/**
* @}
*/
+
+/** @defgroup RCCEx_MCOx_Clock_Config RCC Extended MCOx Clock Config
+ * @{
+ */
+
+/** @brief Macro to configure the MCO1 clock.
+ * @param __MCOCLKSOURCE__ specifies the MCO clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCO1SOURCE_HSI: HSI clock selected as MCO1 source
+ * @arg RCC_MCO1SOURCE_LSE: LSE clock selected as MCO1 source
+ * @arg RCC_MCO1SOURCE_HSE: HSE clock selected as MCO1 source
+ * @arg RCC_MCO1SOURCE_PLLCLK: main PLL clock selected as MCO1 source
+ * @param __MCODIV__ specifies the MCO clock prescaler.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCODIV_1: no division applied to MCOx clock
+ * @arg RCC_MCODIV_2: division by 2 applied to MCOx clock
+ * @arg RCC_MCODIV_3: division by 3 applied to MCOx clock
+ * @arg RCC_MCODIV_4: division by 4 applied to MCOx clock
+ * @arg RCC_MCODIV_5: division by 5 applied to MCOx clock
+ */
+#define __HAL_RCC_MCO1_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \
+ MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO1 | RCC_CFGR_MCO1PRE), ((__MCOCLKSOURCE__) | (__MCODIV__)))
+
+/** @brief Macro to configure the MCO2 clock.
+ * @param __MCOCLKSOURCE__ specifies the MCO clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCO2SOURCE_SYSCLK: System clock (SYSCLK) selected as MCO2 source
+ * @arg RCC_MCO2SOURCE_PLLI2SCLK: PLLI2S clock selected as MCO2 source
+ * @arg RCC_MCO2SOURCE_HSE: HSE clock selected as MCO2 source
+ * @arg RCC_MCO2SOURCE_PLLCLK: main PLL clock selected as MCO2 source
+ * @param __MCODIV__ specifies the MCO clock prescaler.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCODIV_1: no division applied to MCOx clock
+ * @arg RCC_MCODIV_2: division by 2 applied to MCOx clock
+ * @arg RCC_MCODIV_3: division by 3 applied to MCOx clock
+ * @arg RCC_MCODIV_4: division by 4 applied to MCOx clock
+ * @arg RCC_MCODIV_5: division by 5 applied to MCOx clock
+ */
+
+#define __HAL_RCC_MCO2_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \
+ MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO2 | RCC_CFGR_MCO2PRE), ((__MCOCLKSOURCE__) | ((__MCODIV__) << 3)));
+/**
+ * @}
+ */
+
/** @defgroup RCC_Flags_Interrupts_Management Flags Interrupts Management
* @brief macros to manage the specified RCC Flags and interrupts.
* @{
@@ -1225,7 +1270,7 @@
((SOURCE) == RCC_SYSCLKSOURCE_PLLCLK))
#define IS_RCC_PLLM_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 63))
-#define IS_RCC_PLLN_VALUE(VALUE) ((192 <= (VALUE)) && ((VALUE) <= 432))
+#define IS_RCC_PLLN_VALUE(VALUE) ((50 <= (VALUE)) && ((VALUE) <= 432))
#define IS_RCC_PLLP_VALUE(VALUE) (((VALUE) == RCC_PLLP_DIV2) || ((VALUE) == RCC_PLLP_DIV4) || \
((VALUE) == RCC_PLLP_DIV6) || ((VALUE) == RCC_PLLP_DIV8))
@@ -1276,9 +1321,9 @@
#define IS_RCC_LSE_DRIVE(DRIVE) (((DRIVE) == RCC_LSEDRIVE_LOW) || \
- ((DRIVE) == RCC_LSEDRIVE_MEDIUMLOW) || \
- ((DRIVE) == RCC_LSEDRIVE_MEDIUMHIGH) || \
- ((DRIVE) == RCC_LSEDRIVE_HIGH))
+ ((DRIVE) == RCC_LSEDRIVE_MEDIUMLOW) || \
+ ((DRIVE) == RCC_LSEDRIVE_MEDIUMHIGH) || \
+ ((DRIVE) == RCC_LSEDRIVE_HIGH))
/**
* @}
*/