Diff: LIS3DH.h

Revision:

5:725df775f168

Parent:

4:64dac49da306

Child:

6:e269772dad35

diff -r 64dac49da306 -r 725df775f168 LIS3DH.h
--- a/LIS3DH.h	Sat Dec 27 07:43:57 2014 +0000
+++ b/LIS3DH.h	Tue Feb 24 12:21:54 2015 +0000
@@ -3,11 +3,11 @@
  *  LIS3DH MEMS motion sensor: 3-axis "nano" accelerometer, made by STMicroelectronics
  *      http://www.st-japan.co.jp/web/jp/catalog/sense_power/FM89/SC444/PF250725
  *
- * Copyright (c) 2014 Kenji Arai / JH1PJL
+ * Copyright (c) 2014,'15 Kenji Arai / JH1PJL
  *  http://www.page.sannet.ne.jp/kenjia/index.html
  *  http://mbed.org/users/kenjiArai/
  *      Created: July      14th, 2014 
- *      Revised: December  27th, 2014
+ *      Revised: Feburary  24th, 2015
  *
  * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
  * INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
@@ -23,13 +23,12 @@
 
 //  LIS3DH Address
 //  7bit address = 0b001100x(0x18 or 0x19 depends on SA0/SDO)
-//      -> 8bit = 0b001100x0(0x30,0x32) -> 0x31,0x33(Read) or 0x30,0x32(Write)
-#define LIS3DH_G_CHIP_ADDR  0x30    // SA0(=SDO pin) = Ground
-#define LIS3DH_V_CHIP_ADDR  0x32    // SA0(=SDO pin) = Vdd
+#define LIS3DH_G_CHIP_ADDR  (0x18 << 1)    // SA0(=SDO pin) = Ground
+#define LIS3DH_V_CHIP_ADDR  (0x19 << 1)    // SA0(=SDO pin) = Vdd
 
 
 //   LIS3DH ID
-#define I_AM_LIS3DH         0x33
+#define I_AM_LIS3DH            0x33
 
 //  Register's definition
 #define LIS3DH_STATUS_REG_AUX  0x07
@@ -147,27 +146,43 @@
       */
     LIS3DH(PinName p_sda, PinName p_scl,
         uint8_t addr, uint8_t data_rate, uint8_t fullscale);
-    
+
+    /** Configure data pin
+      * @param data SDA and SCL pins
+      * @param device address LIS3DH(SA0=0 or 1), LIS3DH_G_CHIP_ADDR or LIS3DH_V_CHIP_ADDR
+      * @default output data rate selection = 50Hz
+      * @default full scale selection = +/-8g
+      */
+    LIS3DH(PinName p_sda, PinName p_scl, uint8_t addr);
+   
     /** Configure data pin (with other devices on I2C line)
       * @param I2C previous definition
       * @param other parameters -> please see LIS3DH(PinName p_sda, PinName p_scl,...)
       */
     LIS3DH(I2C& p_i2c,
         uint8_t addr, uint8_t data_rate, uint8_t fullscale);
+
+    /** Configure data pin (with other devices on I2C line)
+      * @param I2C previous definition
+      * @param other parameters -> please see LIS3DH(PinName p_sda, PinName p_scl,...)
+      * @default output data rate selection = 50Hz
+      * @default full scale selection = +/-8g
+      */
+    LIS3DH(I2C& p_i2c, uint8_t addr);
    
     /** Read a float type data from acc
-      * @param float type of three arry's address, e.g. float dt[3];
+      * @param float type of three arry's address, e.g. float dt_usr[3];
       * @return acc motion data unit: m/s/s(m/s2)
-      * @return dt[0]->x, dt[1]->y, dt[2]->z 
+      * @return dt_usr[0]->x, dt_usr[1]->y, dt_usr[2]->z 
       */
-    void read_data(float *dt);
+    void read_data(float *dt_usr);
 
     /** Read a float type data from acc
-      * @param float type of three arry's address, e.g. float dt[3];
+      * @param float type of three arry's address, e.g. float dt_usr[3];
       * @return acc motion data unit: mg
-      * @return dt[0]->x, dt[1]->y, dt[2]->z 
+      * @return dt_usr[0]->x, dt_usr[1]->y, dt_usr[2]->z 
       */
-    void read_mg_data(float *dt);
+    void read_mg_data(float *dt_usr);
    
     /** Read a acc ID number
       * @param none
@@ -204,11 +219,11 @@
     void initialize(uint8_t, uint8_t, uint8_t);
     void read_reg_data(char *data);
 
-    I2C i2c;
+    I2C _i2c;
   
 private:
-    float fs_factor;    // full scale factor
-    char dbf[2];        // working buffer
+    float   fs_factor;  // full scale factor
+    char    dt[2];      // working buffer
     uint8_t acc_addr;   // acc sensor address
     uint8_t acc_id;     // acc ID
     uint8_t acc_ready;  // acc is on I2C line = 1, not = 0