File content as of revision 0:d9fd19c8ca39:

#include "mbed.h"
#include "mtsas.h"

int main(){
    //Modify to match your apn if you are using an HSPA radio with a SIM card
    const char APN[] = "";
    
    //Input the phone number below that you want to send the SMS messages to.
    //Send the AT command AT+CNUM to the radio to obtain the phone number of the radio.
    const char PHONE_NUMBER[] = "";
    
    /** STMicro Nucelo F401RE
    * The supported jumper configurations of the MTSAS do not line up with
    * the pin mapping of the Nucleo F401RE. Therefore, the MTSAS serial TX
    * pin (JP8 Pin 2) must be manually jumped to Serial1 RX (Shield pin D2)
    * and the MTSAS serial RX pin (JP9 Pin 2) pin must be manually jumped to
    * Serial1 TX (Shield pin D8).
    * Uncomment the following line to use the STMicro Nuceleo F401RE
    */
    MTSSerialFlowControl* io = new MTSSerialFlowControl(D8, D2, D3, D6);
    
    /** Freescale KL46Z
    * To configure the pins for the Freescale KL46Z board, use configuration B
    * for the SocketModem. The TX pin should be jumped to pin D2 (JP8), and the
    * RX pin should be jumped to pin D9 (JP9). 
    * Uncomment te following line to use the Freescale KL46Z board
    */
    //MTSSerialFlowControl* io = new MTSSerialFlowControl(D2, D9, D3, D6);
    
    /** Freescale KL64F
    * To configure the pins for the Freescale KL46Z board, use configuration A
    * for the SocketModem. The TX pin should be jumped to pin D1 (JP8), and the
    * RX pin should be jumped to pin D0 (JP9). 
    * Uncomment te following line to use the Freescale KL46F board
    */
    //MTSSerialFlowControl* io = new MTSSerialFlowControl(D1, D0, D3, D6);
    
    //Sets the baudrate for communicating with the radio
    io->baud(115200); 
    
    Cellular* radio = CellularFactory::create(io);
    radio->setApn(APN); 
    wait(15);
    
    //Delete all SMS messages
    radio->sendBasicCommand("AT+CMGD=1,4", 1000);
    
    //Setup commands and settings
    radio->sendBasicCommand("AT+CMGF=1", 1000);
    
    /** If the radio is and H5 type (MTSMC_H5, MTSMC_H5_IP) then
     * uncomment the first line. Otherwise, uncomment the second line.
     */
    radio->sendBasicCommand("AT+CSMP=17,167,0,0", 1000);
    //radio->sendBasicCommand("AT+CSMP=,4098,0,2", 1000);
    
    //Format message and send to radio
    char command[100] = {0};
    sprintf(command, "AT+CMGS=\"%s\"", PHONE_NUMBER);
    radio->sendCommand(command, 1000);
    radio->sendCommand("Hello from MultiTechSystems!", 5000, CTRL_Z);
    wait(5);
    
    //Read all messages received
    std::string received = radio->sendCommand("AT+CMGL=\"ALL\"", 2000);
    printf("Messages received:\n%s", received.c_str());
    
    //Delete all messages
    radio->sendBasicCommand("AT+CMGD=1,4", 1000);
    
    printf("End of example code\n");
    return 0;
}