File content as of revision 0:a669868d99dd:

#ifndef REGSSRF04_H
#define REGSSRF04_H

//-------------------------------------------------------------------------------------------------------
// RF_SETTINGS is a data structure which contains all relevant CCxxx0 registers
typedef struct S_RF_SETTINGS{
    char FSCTRL1;   // Frequency synthesizer control.
    char FSCTRL0;   // Frequency synthesizer control.
    char FREQ2;     // Frequency control word, high char.
    char FREQ1;     // Frequency control word, middle char.
    char FREQ0;     // Frequency control word, low char.
    char MDMCFG4;   // Modem configuration.
    char MDMCFG3;   // Modem configuration.
    char MDMCFG2;   // Modem configuration.
    char MDMCFG1;   // Modem configuration.
    char MDMCFG0;   // Modem configuration.
    char CHANNR;    // Channel number.
    char DEVIATN;   // Modem deviation setting (when FSK modulation is enabled).
    char FREND1;    // Front end RX configuration.
    char FREND0;    // Front end RX configuration.
    char MCSM0;     // Main Radio Control State Machine configuration.
    char FOCCFG;    // Frequency Offset Compensation Configuration.
    char BSCFG;     // Bit synchronization Configuration.
    char AGCCTRL2;  // AGC control.
    char AGCCTRL1;  // AGC control.
    char AGCCTRL0;  // AGC control.
    char FSCAL3;    // Frequency synthesizer calibration.
    char FSCAL2;    // Frequency synthesizer calibration.
    char FSCAL1;    // Frequency synthesizer calibration.
    char FSCAL0;    // Frequency synthesizer calibration.
    char FSTEST;    // Frequency synthesizer calibration control
    char TEST2;     // Various test settings.
    char TEST1;     // Various test settings.
    char TEST0;     // Various test settings.
    char FIFOTHR;   // RXFIFO and TXFIFO thresholds.
    char IOCFG2;    // GDO2 output pin configuration
    char IOCFG0;    // GDO0 output pin configuration
    char PKTCTRL1;  // Packet automation control.
    char PKTCTRL0;  // Packet automation control.
    char ADDR;      // Device address.
    char PKTLEN;    // Packet length.
} RF_SETTINGS;



//------------------------------------------------------------------------------------------------------
// CC2500/CC1100 STROBE, CONTROL AND STATUS REGSITER
#define CCxxx0_IOCFG2       0x00        // GDO2 output pin configuration
#define CCxxx0_IOCFG1       0x01        // GDO1 output pin configuration
#define CCxxx0_IOCFG0       0x02        // GDO0 output pin configuration
#define CCxxx0_FIFOTHR      0x03        // RX FIFO and TX FIFO thresholds
#define CCxxx0_SYNC1        0x04        // Sync word, high byte
#define CCxxx0_SYNC0        0x05        // Sync word, low byte
#define CCxxx0_PKTLEN       0x06        // Packet length
#define CCxxx0_PKTCTRL1     0x07        // Packet automation control
#define CCxxx0_PKTCTRL0     0x08        // Packet automation control
#define CCxxx0_ADDR         0x09        // Device address
#define CCxxx0_CHANNR       0x0A        // Channel number
#define CCxxx0_FSCTRL1      0x0B        // Frequency synthesizer control
#define CCxxx0_FSCTRL0      0x0C        // Frequency synthesizer control
#define CCxxx0_FREQ2        0x0D        // Frequency control word, high byte
#define CCxxx0_FREQ1        0x0E        // Frequency control word, middle byte
#define CCxxx0_FREQ0        0x0F        // Frequency control word, low byte
#define CCxxx0_MDMCFG4      0x10        // Modem configuration
#define CCxxx0_MDMCFG3      0x11        // Modem configuration
#define CCxxx0_MDMCFG2      0x12        // Modem configuration
#define CCxxx0_MDMCFG1      0x13        // Modem configuration
#define CCxxx0_MDMCFG0      0x14        // Modem configuration
#define CCxxx0_DEVIATN      0x15        // Modem deviation setting
#define CCxxx0_MCSM2        0x16        // Main Radio Control State Machine configuration
#define CCxxx0_MCSM1        0x17        // Main Radio Control State Machine configuration
#define CCxxx0_MCSM0        0x18        // Main Radio Control State Machine configuration
#define CCxxx0_FOCCFG       0x19        // Frequency Offset Compensation configuration
#define CCxxx0_BSCFG        0x1A        // Bit Synchronization configuration
#define CCxxx0_AGCCTRL2     0x1B        // AGC control
#define CCxxx0_AGCCTRL1     0x1C        // AGC control
#define CCxxx0_AGCCTRL0     0x1D        // AGC control
#define CCxxx0_WOREVT1      0x1E        // High byte Event 0 timeout
#define CCxxx0_WOREVT0      0x1F        // Low byte Event 0 timeout
#define CCxxx0_WORCTRL      0x20        // Wake On Radio control
#define CCxxx0_FREND1       0x21        // Front end RX configuration
#define CCxxx0_FREND0       0x22        // Front end TX configuration
#define CCxxx0_FSCAL3       0x23        // Frequency synthesizer calibration
#define CCxxx0_FSCAL2       0x24        // Frequency synthesizer calibration
#define CCxxx0_FSCAL1       0x25        // Frequency synthesizer calibration
#define CCxxx0_FSCAL0       0x26        // Frequency synthesizer calibration
#define CCxxx0_RCCTRL1      0x27        // RC oscillator configuration
#define CCxxx0_RCCTRL0      0x28        // RC oscillator configuration
#define CCxxx0_FSTEST       0x29        // Frequency synthesizer calibration control
#define CCxxx0_PTEST        0x2A        // Production test
#define CCxxx0_AGCTEST      0x2B        // AGC test
#define CCxxx0_TEST2        0x2C        // Various test settings
#define CCxxx0_TEST1        0x2D        // Various test settings
#define CCxxx0_TEST0        0x2E        // Various test settings

// Strobe commands
#define CCxxx0_SRES         0x30        // Reset chip.
#define CCxxx0_SFSTXON      0x31        // Enable and calibrate frequency synthesizer (if MCSM0.FS_AUTOCAL=1).
                                        // If in RX/TX: Go to a wait state where only the synthesizer is
                                        // running (for quick RX / TX turnaround).
#define CCxxx0_SXOFF        0x32        // Turn off crystal oscillator.
#define CCxxx0_SCAL         0x33        // Calibrate frequency synthesizer and turn it off
                                        // (enables quick start).
#define CCxxx0_SRX          0x34        // Enable RX. Perform calibration first if coming from IDLE and
                                        // MCSM0.FS_AUTOCAL=1.
#define CCxxx0_STX          0x35        // In IDLE state: Enable TX. Perform calibration first if
                                        // MCSM0.FS_AUTOCAL=1. If in RX state and CCA is enabled:
                                        // Only go to TX if channel is clear.
#define CCxxx0_SIDLE        0x36        // Exit RX / TX, turn off frequency synthesizer and exit
                                        // Wake-On-Radio mode if applicable.
#define CCxxx0_SAFC         0x37        // Perform AFC adjustment of the frequency synthesizer
#define CCxxx0_SWOR         0x38        // Start automatic RX polling sequence (Wake-on-Radio)
#define CCxxx0_SPWD         0x39        // Enter power down mode when CSn goes high.
#define CCxxx0_SFRX         0x3A        // Flush the RX FIFO buffer.
#define CCxxx0_SFTX         0x3B        // Flush the TX FIFO buffer.
#define CCxxx0_SWORRST      0x3C        // Reset real time clock.
#define CCxxx0_SNOP         0x3D        // No operation. May be used to pad strobe commands to two
                                        // bytes for simpler software.

#define CCxxx0_PARTNUM          0x30
#define CCxxx0_VERSION          0x31
#define CCxxx0_FREQEST          0x32
#define CCxxx0_LQI              0x33
#define CCxxx0_RSSI             0x34
#define CCxxx0_MARCSTATE        0x35
#define CCxxx0_WORTIME1         0x36
#define CCxxx0_WORTIME0         0x37
#define CCxxx0_PKTSTATUS        0x38
#define CCxxx0_VCO_VC_DAC       0x39
#define CCxxx0_TXBYTES          0x3A
#define CCxxx0_RXBYTES          0x3B
#define CCxxx0_RCCTRL1_STATUS   0x3C
#define CCxxx0_RCCTRL0_STATUS   0x3D

#define CCxxx0_PATABLE          0x3E
#define CCxxx0_TXFIFO           0x3F
#define CCxxx0_RXFIFO           0x3F


#define CCxxx0_RECEIVE_CRC_ERROR    0x00
#define CCxxx0_RECEIVE_CRC_OK       0x80

#endif//REGSSRF04_H