Diff: RF22Datagram.h

Revision:

0:79c6d0071c4c

Child:

5:0386600f3408

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/RF22Datagram.h	Tue Feb 14 19:39:36 2012 +0000
@@ -0,0 +1,77 @@
+// RF22Datagram.h
+// Author: Mike McCauley (mikem@open.com.au)
+// Copyright (C) 2011 Mike McCauley
+// $Id: RF22Datagram.h,v 1.3 2011/02/15 01:18:03 mikem Exp $
+// ported to mbed by Karl Zweimueller
+
+#ifndef RF22Datagram_h
+#define RF22Datagram_h
+
+#include <RF22.h>
+
+/////////////////////////////////////////////////////////////////////
+/// \class RF22Datagram RF22Datagram.h <RF22Datagram.h>
+/// \brief RF22 subclass for addressed, unreliable messages
+///
+/// Extends RF22 to define addressed, unreliable datagrams.
+/// Every node has an 8 bit address (defaults to 0).
+/// Addresses (DEST and SRC) are 8 bit integers with an address of RF22_BROADCAST_ADDRESS (0xff) 
+/// reserved for broadcast.
+///
+/// Part of the Arduino RF22 library for operating with HopeRF RF22 compatible transceivers 
+/// (see http://www.hoperf.com).
+class RF22Datagram : public RF22
+{
+public:
+    /// Constructor. 
+    /// \param[in] thisAddress The address to assign to this node. Defaults to 0
+    /// \param[in] slaveSelectPin the Arduino pin number of the output to use to select the RF22 before
+    /// accessing it
+    /// \param[in] interrupt The interrupt number to use. Default is interrupt 0 (Arduino input pin 2)
+    RF22Datagram(uint8_t thisAddress ,PinName slaveSelectPin , PinName mosi, PinName miso, PinName sclk, PinName interrupt );
+    
+    /// Initialises this instance and the radio module connected to it.
+    /// Overrides the init() function in RF22
+    boolean init();
+
+    /// Sets the address of this node. Defaults to 0. 
+    /// This will be used to set the FROM address of all messages sent by this node.
+    /// If all the nodes leave the address unset (ie 0),
+    /// In a conventional multinode system, all nodes will have a unique address 
+    /// (which you could store in EEPROM).
+    /// \param[in] thisAddress The address of this node
+    void setThisAddress(uint8_t thisAddress);
+
+    /// Sends a message to the node(s) with the given address
+    /// RF22_BROADCAST_ADDRESS is a valid address which will cause the message
+    /// to be accepted by all RF22Datagram nodes within range.
+    /// \param[in] buf Pointer to the binary message to send
+    /// \param[in] len Number of octets to send
+    /// \param[in] address The address to send the message to.
+    /// \return true if the message was transmitted.
+    boolean sendto(uint8_t* buf, uint8_t len, uint8_t address);
+
+    /// Turns the receiver on if it not already on.
+    /// If there is a valid message available for this node, copy it to buf and return true
+    /// The SRC address is placed in *from if present and not NULL.
+    /// The DEST address is placed in *to if present and not NULL.
+    /// If a message is copied, *len is set to the length.
+    /// You should be sure to call this function frequently enough to not miss any messages
+    /// It is recommended that you call it in your main loop.
+    /// \param[in] buf Location to copy the received message
+    /// \param[in,out] len Pointer to available space in buf. Set to the actual number of octets copied.
+    /// \param[in] from If present and not NULL, the referenced uint8_t will be set to the FROM address
+    /// \param[in] to If present and not NULL, the referenced uint8_t will be set to the TO address
+    /// \param[in] id If present and not NULL, the referenced uint8_t will be set to the ID
+    /// \param[in] flags If present and not NULL, the referenced uint8_t will be set to the FLAGS
+    /// (not just those addressed to this node).
+    /// \return true if a valid message was copied to buf
+    boolean recvfrom(uint8_t* buf, uint8_t* len, uint8_t* from = NULL, uint8_t* to = NULL, uint8_t* id = NULL, uint8_t* flags = NULL);
+
+protected:
+    /// The address of this node. Defaults to 0.
+    uint8_t _thisAddress;
+
+};
+
+#endif