keniti akiba
/
f303_h_p1
f303_h_p1 1
Diff: LCD_HELLO_010_1/main.c
- Revision:
- 8:1099c3102bf7
diff -r 02fa6ef78ec9 -r 1099c3102bf7 LCD_HELLO_010_1/main.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/LCD_HELLO_010_1/main.c Sun Nov 21 21:53:56 2021 +0000 @@ -0,0 +1,351 @@ +/* USER CODE BEGIN Header */ +/** + ****************************************************************************** + * @file : main.c + * @brief : Main program body + ****************************************************************************** + * @attention + * + * <h2><center>© Copyright (c) 2021 STMicroelectronics. + * All rights reserved.</center></h2> + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ +/* USER CODE END Header */ +/* Includes ------------------------------------------------------------------*/ +#include "main.h" + +/* Private includes ----------------------------------------------------------*/ +/* USER CODE BEGIN Includes */ + +/* USER CODE END Includes */ + +/* Private typedef -----------------------------------------------------------*/ +/* USER CODE BEGIN PTD */ + +/* USER CODE END PTD */ + +/* Private define ------------------------------------------------------------*/ +/* USER CODE BEGIN PD */ +/* USER CODE END PD */ + +/* Private macro -------------------------------------------------------------*/ +/* USER CODE BEGIN PM */ + +/* USER CODE END PM */ + +/* Private variables ---------------------------------------------------------*/ +I2C_HandleTypeDef hi2c1; + +UART_HandleTypeDef huart2; + +/* USER CODE BEGIN PV */ + +/* USER CODE END PV */ + +/* Private function prototypes -----------------------------------------------*/ +void SystemClock_Config(void); +static void MX_GPIO_Init(void); +static void MX_I2C1_Init(void); +static void MX_USART2_UART_Init(void); +/* USER CODE BEGIN PFP */ + +/* USER CODE END PFP */ + +/* Private user code ---------------------------------------------------------*/ +/* USER CODE BEGIN 0 */ + +/* USER CODE END 0 */ + +/** + * @brief The application entry point. + * @retval int + */ +int main(void) +{ + /* USER CODE BEGIN 1 */ + + /* USER CODE END 1 */ + + /* MCU Configuration--------------------------------------------------------*/ + + /* Reset of all peripherals, Initializes the Flash interface and the Systick. */ + HAL_Init(); + + /* USER CODE BEGIN Init */ + + /* USER CODE END Init */ + + /* Configure the system clock */ + SystemClock_Config(); + + /* USER CODE BEGIN SysInit */ + + /* USER CODE END SysInit */ + + /* Initialize all configured peripherals */ + MX_GPIO_Init(); + MX_I2C1_Init(); + MX_USART2_UART_Init(); + /* USER CODE BEGIN 2 */ + +#define ADDR_LCD (0x7C) // address + +uint8_t INIT_com[]={ +0x0,0x38, +0x0,0x39, +0x0,0x4, +0x0,0x14, +0x0,0x70, +0x0,0x56, +0x0,0x6C, +0x0,0x38, +0x0,0xC, +0x0,0x1, +0x40,0x41}; + +uint8_t INIT_cls[]={0x0,0x1}; + + + + //液晶の初期化 + HAL_Delay(200); + for(int ii=0;ii<11;ii++){ + HAL_I2C_Master_Transmit(&hi2c1, ADDR_LCD, &INIT_com[ii*2], 2, 3000); + HAL_Delay(3); + } //for + + + + + /* USER CODE END 2 */ + + /* Infinite loop */ + /* USER CODE BEGIN WHILE */ + while (1) + { + /* USER CODE END WHILE */ + + + + //液晶のクリア + HAL_I2C_Master_Transmit(&hi2c1, ADDR_LCD, INIT_cls, 2, 3000); + HAL_Delay(3); + + //液晶に出力 xなぜか連続送信するとバグる為に個別送信 + uint8_t a[]="HELLO",b[]="@A"; + for(int ii=0;ii< sizeof(a) ;ii++){ + b[1]=a[ii]; + HAL_I2C_Master_Transmit(&hi2c1, ADDR_LCD, b , 2 , 3000); + HAL_Delay(1); + }//for + + //1秒待つ + HAL_Delay(1000); + + + + /* USER CODE BEGIN 3 */ + } + /* USER CODE END 3 */ +} + +/** + * @brief System Clock Configuration + * @retval None + */ +void SystemClock_Config(void) +{ + RCC_OscInitTypeDef RCC_OscInitStruct = {0}; + RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; + RCC_PeriphCLKInitTypeDef PeriphClkInit = {0}; + + /** Configure the main internal regulator output voltage + */ + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + /** Initializes the RCC Oscillators according to the specified parameters + * in the RCC_OscInitTypeDef structure. + */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI; + RCC_OscInitStruct.HSIState = RCC_HSI_ON; + RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI; + RCC_OscInitStruct.PLL.PLLMUL = RCC_PLLMUL_4; + RCC_OscInitStruct.PLL.PLLDIV = RCC_PLLDIV_2; + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) + { + Error_Handler(); + } + /** Initializes the CPU, AHB and APB buses clocks + */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK + |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; + + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK) + { + Error_Handler(); + } + PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART2|RCC_PERIPHCLK_I2C1; + PeriphClkInit.Usart2ClockSelection = RCC_USART2CLKSOURCE_PCLK1; + PeriphClkInit.I2c1ClockSelection = RCC_I2C1CLKSOURCE_PCLK1; + if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK) + { + Error_Handler(); + } +} + +/** + * @brief I2C1 Initialization Function + * @param None + * @retval None + */ +static void MX_I2C1_Init(void) +{ + + /* USER CODE BEGIN I2C1_Init 0 */ + + /* USER CODE END I2C1_Init 0 */ + + /* USER CODE BEGIN I2C1_Init 1 */ + + /* USER CODE END I2C1_Init 1 */ + hi2c1.Instance = I2C1; + hi2c1.Init.Timing = 0x00707CBB; + hi2c1.Init.OwnAddress1 = 0; + hi2c1.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT; + hi2c1.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE; + hi2c1.Init.OwnAddress2 = 0; + hi2c1.Init.OwnAddress2Masks = I2C_OA2_NOMASK; + hi2c1.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE; + hi2c1.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE; + if (HAL_I2C_Init(&hi2c1) != HAL_OK) + { + Error_Handler(); + } + /** Configure Analogue filter + */ + if (HAL_I2CEx_ConfigAnalogFilter(&hi2c1, I2C_ANALOGFILTER_ENABLE) != HAL_OK) + { + Error_Handler(); + } + /** Configure Digital filter + */ + if (HAL_I2CEx_ConfigDigitalFilter(&hi2c1, 0) != HAL_OK) + { + Error_Handler(); + } + /* USER CODE BEGIN I2C1_Init 2 */ + + /* USER CODE END I2C1_Init 2 */ + +} + +/** + * @brief USART2 Initialization Function + * @param None + * @retval None + */ +static void MX_USART2_UART_Init(void) +{ + + /* USER CODE BEGIN USART2_Init 0 */ + + /* USER CODE END USART2_Init 0 */ + + /* USER CODE BEGIN USART2_Init 1 */ + + /* USER CODE END USART2_Init 1 */ + huart2.Instance = USART2; + huart2.Init.BaudRate = 115200; + huart2.Init.WordLength = UART_WORDLENGTH_8B; + huart2.Init.StopBits = UART_STOPBITS_1; + huart2.Init.Parity = UART_PARITY_NONE; + huart2.Init.Mode = UART_MODE_TX_RX; + huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE; + huart2.Init.OverSampling = UART_OVERSAMPLING_16; + huart2.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE; + huart2.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT; + if (HAL_UART_Init(&huart2) != HAL_OK) + { + Error_Handler(); + } + /* USER CODE BEGIN USART2_Init 2 */ + + /* USER CODE END USART2_Init 2 */ + +} + +/** + * @brief GPIO Initialization Function + * @param None + * @retval None + */ +static void MX_GPIO_Init(void) +{ + GPIO_InitTypeDef GPIO_InitStruct = {0}; + + /* GPIO Ports Clock Enable */ + __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOA_CLK_ENABLE(); + __HAL_RCC_GPIOB_CLK_ENABLE(); + + /*Configure GPIO pin Output Level */ + HAL_GPIO_WritePin(LD3_GPIO_Port, LD3_Pin, GPIO_PIN_RESET); + + /*Configure GPIO pin : LD3_Pin */ + GPIO_InitStruct.Pin = LD3_Pin; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; + HAL_GPIO_Init(LD3_GPIO_Port, &GPIO_InitStruct); + +} + +/* USER CODE BEGIN 4 */ + +/* USER CODE END 4 */ + +/** + * @brief This function is executed in case of error occurrence. + * @retval None + */ +void Error_Handler(void) +{ + /* USER CODE BEGIN Error_Handler_Debug */ + /* User can add his own implementation to report the HAL error return state */ + __disable_irq(); + while (1) + { + } + /* USER CODE END Error_Handler_Debug */ +} + +#ifdef USE_FULL_ASSERT +/** + * @brief Reports the name of the source file and the source line number + * where the assert_param error has occurred. + * @param file: pointer to the source file name + * @param line: assert_param error line source number + * @retval None + */ +void assert_failed(uint8_t *file, uint32_t line) +{ + /* USER CODE BEGIN 6 */ + /* User can add his own implementation to report the file name and line number, + ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ + /* USER CODE END 6 */ +} +#endif /* USE_FULL_ASSERT */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ +