Diff: stm32l010_lpuart1_1/main.c

Revision:

14:4b2aa14add81

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/stm32l010_lpuart1_1/main.c	Tue Nov 30 19:38:14 2021 +0000
@@ -0,0 +1,309 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file           : main.c
+  * @brief          : Main program body
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2021 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+
+/* Private includes ----------------------------------------------------------*/
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+/* Private typedef -----------------------------------------------------------*/
+/* USER CODE BEGIN PTD */
+
+/* USER CODE END PTD */
+
+/* Private define ------------------------------------------------------------*/
+/* USER CODE BEGIN PD */
+/* USER CODE END PD */
+
+/* Private macro -------------------------------------------------------------*/
+/* USER CODE BEGIN PM */
+
+/* USER CODE END PM */
+
+/* Private variables ---------------------------------------------------------*/
+UART_HandleTypeDef hlpuart1;
+UART_HandleTypeDef huart2;
+
+/* USER CODE BEGIN PV */
+
+/* USER CODE END PV */
+
+/* Private function prototypes -----------------------------------------------*/
+void SystemClock_Config(void);
+static void MX_GPIO_Init(void);
+static void MX_LPUART1_UART_Init(void);
+static void MX_USART2_UART_Init(void);
+/* USER CODE BEGIN PFP */
+
+/* USER CODE END PFP */
+
+/* Private user code ---------------------------------------------------------*/
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+
+/**
+  * @brief  The application entry point.
+  * @retval int
+  */
+int main(void)
+{
+  /* USER CODE BEGIN 1 */
+
+  /* USER CODE END 1 */
+
+  /* MCU Configuration--------------------------------------------------------*/
+
+  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
+  HAL_Init();
+
+  /* USER CODE BEGIN Init */
+
+  /* USER CODE END Init */
+
+  /* Configure the system clock */
+  SystemClock_Config();
+
+  /* USER CODE BEGIN SysInit */
+
+  /* USER CODE END SysInit */
+
+  /* Initialize all configured peripherals */
+  MX_GPIO_Init();
+  MX_LPUART1_UART_Init();
+  MX_USART2_UART_Init();
+  /* USER CODE BEGIN 2 */
+
+  /* USER CODE END 2 */
+
+  /* Infinite loop */
+  /* USER CODE BEGIN WHILE */
+  while (1)
+  {
+    /* USER CODE END WHILE */
+
+
+    HAL_UART_Transmit(&hlpuart1, (uint8_t *)"hello world\r\n", 13, 10);
+
+    //HAL_Delay(500);
+
+
+
+  
+    
+    
+    HAL_GPIO_WritePin(LD3_GPIO_Port, LD3_Pin, GPIO_PIN_SET);
+    HAL_Delay(500);
+    
+    HAL_GPIO_WritePin(LD3_GPIO_Port, LD3_Pin, GPIO_PIN_RESET);
+    HAL_Delay(500);
+    
+ 
+
+
+    /* USER CODE BEGIN 3 */
+  }
+  /* USER CODE END 3 */
+}
+
+/**
+  * @brief System Clock Configuration
+  * @retval None
+  */
+void SystemClock_Config(void)
+{
+  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+  RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};
+
+  /** Configure the main internal regulator output voltage
+  */
+  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+  /** Initializes the RCC Oscillators according to the specified parameters
+  * in the RCC_OscInitTypeDef structure.
+  */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
+  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLLMUL_4;
+  RCC_OscInitStruct.PLL.PLLDIV = RCC_PLLDIV_2;
+  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /** Initializes the CPU, AHB and APB buses clocks
+  */
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
+                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+
+  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART2|RCC_PERIPHCLK_LPUART1;
+  PeriphClkInit.Usart2ClockSelection = RCC_USART2CLKSOURCE_PCLK1;
+  PeriphClkInit.Lpuart1ClockSelection = RCC_LPUART1CLKSOURCE_PCLK1;
+  if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
+  {
+    Error_Handler();
+  }
+}
+
+/**
+  * @brief LPUART1 Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_LPUART1_UART_Init(void)
+{
+
+  /* USER CODE BEGIN LPUART1_Init 0 */
+
+  /* USER CODE END LPUART1_Init 0 */
+
+  /* USER CODE BEGIN LPUART1_Init 1 */
+
+  /* USER CODE END LPUART1_Init 1 */
+  hlpuart1.Instance = LPUART1;
+  hlpuart1.Init.BaudRate = 209700;
+  hlpuart1.Init.WordLength = UART_WORDLENGTH_7B;
+  hlpuart1.Init.StopBits = UART_STOPBITS_1;
+  hlpuart1.Init.Parity = UART_PARITY_NONE;
+  hlpuart1.Init.Mode = UART_MODE_TX_RX;
+  hlpuart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;
+  hlpuart1.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
+  hlpuart1.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
+  if (HAL_HalfDuplex_Init(&hlpuart1) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN LPUART1_Init 2 */
+
+  /* USER CODE END LPUART1_Init 2 */
+
+}
+
+/**
+  * @brief USART2 Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_USART2_UART_Init(void)
+{
+
+  /* USER CODE BEGIN USART2_Init 0 */
+
+  /* USER CODE END USART2_Init 0 */
+
+  /* USER CODE BEGIN USART2_Init 1 */
+
+  /* USER CODE END USART2_Init 1 */
+  huart2.Instance = USART2;
+  huart2.Init.BaudRate = 115200;
+  huart2.Init.WordLength = UART_WORDLENGTH_8B;
+  huart2.Init.StopBits = UART_STOPBITS_1;
+  huart2.Init.Parity = UART_PARITY_NONE;
+  huart2.Init.Mode = UART_MODE_TX_RX;
+  huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE;
+  huart2.Init.OverSampling = UART_OVERSAMPLING_16;
+  huart2.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
+  huart2.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
+  if (HAL_UART_Init(&huart2) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN USART2_Init 2 */
+
+  /* USER CODE END USART2_Init 2 */
+
+}
+
+/**
+  * @brief GPIO Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_GPIO_Init(void)
+{
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+
+  /* GPIO Ports Clock Enable */
+  __HAL_RCC_GPIOC_CLK_ENABLE();
+  __HAL_RCC_GPIOA_CLK_ENABLE();
+  __HAL_RCC_GPIOB_CLK_ENABLE();
+
+  /*Configure GPIO pin Output Level */
+  HAL_GPIO_WritePin(LD3_GPIO_Port, LD3_Pin, GPIO_PIN_RESET);
+
+  /*Configure GPIO pin : LD3_Pin */
+  GPIO_InitStruct.Pin = LD3_Pin;
+  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+  HAL_GPIO_Init(LD3_GPIO_Port, &GPIO_InitStruct);
+
+}
+
+/* USER CODE BEGIN 4 */
+
+/* USER CODE END 4 */
+
+/**
+  * @brief  This function is executed in case of error occurrence.
+  * @retval None
+  */
+void Error_Handler(void)
+{
+  /* USER CODE BEGIN Error_Handler_Debug */
+  /* User can add his own implementation to report the HAL error return state */
+  __disable_irq();
+  while (1)
+  {
+  }
+  /* USER CODE END Error_Handler_Debug */
+}
+
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  Reports the name of the source file and the source line number
+  *         where the assert_param error has occurred.
+  * @param  file: pointer to the source file name
+  * @param  line: assert_param error line source number
+  * @retval None
+  */
+void assert_failed(uint8_t *file, uint32_t line)
+{
+  /* USER CODE BEGIN 6 */
+  /* User can add his own implementation to report the file name and line number,
+     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
+  /* USER CODE END 6 */
+}
+#endif /* USE_FULL_ASSERT */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+