Driver for SX1272 connected to Pulga devices using only DIO0 pins and polling (error states and timeout).
Dependents: pulga-mbed-lorawan-gps mbed-lorawan-pulga mbed-lorawan-pulga-testing-channel mbed-lorawan-pulga-serial_rx ... more
SX126X/SX126X_LoRaRadio.cpp
- Committer:
- brunnobbco
- Date:
- 2021-03-30
- Revision:
- 5:3da1a3924c65
- Parent:
- 0:561d07a737bc
File content as of revision 5:3da1a3924c65:
/** / _____) _ | | ( (____ _____ ____ _| |_ _____ ____| |__ \____ \| ___ | (_ _) ___ |/ ___) _ \ _____) ) ____| | | || |_| ____( (___| | | | (______/|_____)_|_|_| \__)_____)\____)_| |_| (C)2015 Semtech ___ _____ _ ___ _ _____ ___ ___ ___ ___ / __|_ _/_\ / __| |/ / __/ _ \| _ \/ __| __| \__ \ | |/ _ \ (__| ' <| _| (_) | / (__| _| |___/ |_/_/ \_\___|_|\_\_| \___/|_|_\\___|___| embedded.connectivity.solutions=============== Description: LoRaWAN stack layer that controls both MAC and PHY underneath License: Revised BSD License, see LICENSE.TXT file include in the project Maintainer: Miguel Luis, Gregory Cristian & Gilbert Menth Copyright (c) 2019, Arm Limited and affiliates. SPDX-License-Identifier: BSD-3-Clause */ #include <math.h> #include "mbed_wait_api.h" #include "Timer.h" #include "SX126X_LoRaRadio.h" #ifdef MBED_CONF_SX126X_LORA_DRIVER_SPI_FREQUENCY #define SPI_FREQUENCY MBED_CONF_SX126X_LORA_DRIVER_SPI_FREQUENCY #else #define SPI_FREQUENCY 16000000 #endif using namespace mbed; #ifdef MBED_CONF_RTOS_PRESENT using namespace rtos; /** * Signals */ #define SIG_INTERRUPT 0x02 #endif /*! * FSK bandwidth definition */ typedef struct { uint32_t bandwidth; uint8_t register_value; } fsk_bw_t; static const fsk_bw_t fsk_bandwidths[] = { { 4800 , 0x1F }, { 5800 , 0x17 }, { 7300 , 0x0F }, { 9700 , 0x1E }, { 11700 , 0x16 }, { 14600 , 0x0E }, { 19500 , 0x1D }, { 23400 , 0x15 }, { 29300 , 0x0D }, { 39000 , 0x1C }, { 46900 , 0x14 }, { 58600 , 0x0C }, { 78200 , 0x1B }, { 93800 , 0x13 }, { 117300, 0x0B }, { 156200, 0x1A }, { 187200, 0x12 }, { 234300, 0x0A }, { 312000, 0x19 }, { 373600, 0x11 }, { 467000, 0x09 }, { 500000, 0x00 }, // Invalid Bandwidth }; const uint8_t sync_word[] = {0xC1, 0x94, 0xC1, 0x00, 0x00, 0x00, 0x00,0x00}; // in ms SF12 SF11 SF10 SF9 SF8 SF7 const float lora_symbol_time[3][6] = {{ 32.768, 16.384, 8.192, 4.096, 2.048, 1.024 }, // 125 KHz { 16.384, 8.192, 4.096, 2.048, 1.024, 0.512 }, // 250 KHz { 8.192, 4.096, 2.048, 1.024, 0.512, 0.256 }}; // 500 KHz SX126X_LoRaRadio::SX126X_LoRaRadio(PinName mosi, PinName miso, PinName sclk, PinName nss, PinName reset, PinName dio1, PinName busy, PinName freq_select, PinName device_select, PinName crystal_select, PinName ant_switch) : _spi(mosi, miso, sclk), _chip_select(nss, 1), _reset_ctl(reset), _dio1_ctl(dio1, PullNone), _busy(busy, PullNone), _freq_select(freq_select), _dev_select(device_select), _crystal_select(crystal_select, PullDown), _ant_switch(ant_switch, PIN_INPUT, PullUp, 0) #ifdef MBED_CONF_RTOS_PRESENT , irq_thread(osPriorityRealtime, 1024, NULL, "LR-SX126X") #endif { _radio_events = NULL; _reset_ctl = 1; _image_calibrated = false; _force_image_calibration = false; _active_modem = MODEM_LORA; #ifdef MBED_CONF_RTOS_PRESENT irq_thread.start(callback(this, &SX126X_LoRaRadio::rf_irq_task)); #endif } SX126X_LoRaRadio::~SX126X_LoRaRadio() { } /** * Acquire lock */ void SX126X_LoRaRadio::lock(void) { mutex.lock(); } /** * Release lock */ void SX126X_LoRaRadio::unlock(void) { mutex.unlock(); } #ifdef MBED_CONF_RTOS_PRESENT /** * Thread task handling IRQs */ void SX126X_LoRaRadio::rf_irq_task(void) { for (;;) { uint32_t flags = ThisThread::flags_wait_any(0x7FFFFFFF); lock(); if (flags & SIG_INTERRUPT) { handle_dio1_irq(); } unlock(); } } #endif void SX126X_LoRaRadio::dio1_irq_isr() { #ifdef MBED_CONF_RTOS_PRESENT irq_thread.flags_set(SIG_INTERRUPT); #else handle_dio1_irq(); #endif } uint16_t SX126X_LoRaRadio::get_irq_status(void) { uint8_t status[2]; read_opmode_command((uint8_t) RADIO_GET_IRQSTATUS, status, 2); return (status[0] << 8) | status[1]; } void SX126X_LoRaRadio::clear_irq_status(uint16_t irq) { uint8_t buf[2]; buf[0] = (uint8_t) (((uint16_t) irq >> 8) & 0x00FF); buf[1] = (uint8_t) ((uint16_t) irq & 0x00FF); write_opmode_command((uint8_t) RADIO_CLR_IRQSTATUS, buf, 2); } //TODO - Better do CAD here. CAD code is already part of the driver // It needs to be hooked up to the stack (this API will need change // and the stack will need changes too) bool SX126X_LoRaRadio::perform_carrier_sense(radio_modems_t modem, uint32_t freq, int16_t rssi_threshold, uint32_t max_carrier_sense_time) { bool status = true; int16_t rssi = 0; set_modem(modem); set_channel(freq); _reception_mode = RECEPTION_MODE_OTHER; _rx_timeout = 0x00000000; receive(); // hold on a bit, radio turn-around time wait_ms(1); Timer elapsed_time; elapsed_time.start(); // Perform carrier sense for maxCarrierSenseTime while (elapsed_time.read_ms() < (int) max_carrier_sense_time) { rssi = get_rssi(); if (rssi > rssi_threshold) { status = false; break; } } sleep(); return status; } void SX126X_LoRaRadio::start_cad(void) { // TODO: CAD is more advanced in SX126X. We will need API change in LoRaRadio // for this to act properly } /** * TODO: The purpose of this API is unclear. * Need to start an internal discussion. */ bool SX126X_LoRaRadio::check_rf_frequency(uint32_t frequency) { // Implement check. Currently all frequencies are supported ? What band ? return true; } void SX126X_LoRaRadio::set_tx_continuous_wave(uint32_t freq, int8_t power, uint16_t time) { // This is useless. We even removed the support from our MAC layer. } void SX126X_LoRaRadio::handle_dio1_irq() { uint16_t irq_status = get_irq_status(); clear_irq_status(IRQ_RADIO_ALL); if ((irq_status & IRQ_TX_DONE) == IRQ_TX_DONE) { if (_radio_events->tx_done) { _radio_events->tx_done(); } } if ((irq_status & IRQ_RX_DONE) == IRQ_RX_DONE) { if ((irq_status & IRQ_CRC_ERROR) == IRQ_CRC_ERROR) { if (_radio_events && _radio_events->rx_error) { _radio_events->rx_error(); } } else { if (_radio_events->rx_done) { uint8_t offset = 0; uint8_t payload_len = 0; int16_t rssi = 0; int8_t snr = 0; packet_status_t pkt_status; get_rx_buffer_status(&payload_len, &offset); read_fifo(_data_buffer, payload_len, offset); get_packet_status(&pkt_status); if (pkt_status.modem_type == MODEM_FSK) { rssi = pkt_status.params.gfsk.rssi_sync; } else { rssi = pkt_status.params.lora.rssi_pkt; snr = pkt_status.params.lora.snr_pkt; } _radio_events->rx_done(_data_buffer, payload_len, rssi, snr); } } } if ((irq_status & IRQ_CAD_DONE) == IRQ_CAD_DONE) { if (_radio_events->cad_done) { _radio_events->cad_done((irq_status & IRQ_CAD_ACTIVITY_DETECTED) == IRQ_CAD_ACTIVITY_DETECTED); } } if ((irq_status & IRQ_RX_TX_TIMEOUT) == IRQ_RX_TX_TIMEOUT) { if ((_radio_events->tx_timeout) && (_operation_mode == MODE_TX)) { _radio_events->tx_timeout(); } else if ((_radio_events && _radio_events->rx_timeout) && (_operation_mode == MODE_RX)) { _radio_events->rx_timeout(); } } } void SX126X_LoRaRadio::set_device_ready(void) { if (_operation_mode == MODE_SLEEP) { wakeup(); } } void SX126X_LoRaRadio::calibrate_image(uint32_t freq) { uint8_t cal_freq[2]; if (freq > 900000000) { cal_freq[0] = 0xE1; cal_freq[1] = 0xE9; } else if (freq > 850000000) { cal_freq[0] = 0xD7; cal_freq[1] = 0xD8; } else if (freq > 770000000) { cal_freq[0] = 0xC1; cal_freq[1] = 0xC5; } else if (freq > 460000000) { cal_freq[0] = 0x75; cal_freq[1] = 0x81; } else if (freq > 425000000) { cal_freq[0] = 0x6B; cal_freq[1] = 0x6F; } write_opmode_command((uint8_t) RADIO_CALIBRATEIMAGE, cal_freq, 2); _image_calibrated = true; } void SX126X_LoRaRadio::set_channel(uint32_t frequency) { #if MBED_CONF_SX126X_LORA_DRIVER_SLEEP_MODE == 1 // At this point, we are not sure what is the Modem type, set both _mod_params.params.lora.operational_frequency = frequency; _mod_params.params.gfsk.operational_frequency = frequency; #endif uint8_t buf[4]; uint32_t freq = 0; if ( _force_image_calibration || !_image_calibrated) { calibrate_image(frequency); _image_calibrated = true; } freq = (uint32_t) ceil(((float) frequency / (float) FREQ_STEP)); buf[0] = (uint8_t) ((freq >> 24) & 0xFF); buf[1] = (uint8_t) ((freq >> 16) & 0xFF); buf[2] = (uint8_t) ((freq >> 8) & 0xFF); buf[3] = (uint8_t) (freq & 0xFF); write_opmode_command((uint8_t) RADIO_SET_RFFREQUENCY, buf, 4); } /** * Put radio in Standby mode */ void SX126X_LoRaRadio::standby(void) { if (_operation_mode == MODE_STDBY_RC) { return; } set_device_ready(); uint8_t standby_mode = MBED_CONF_SX126X_LORA_DRIVER_STANDBY_MODE; write_opmode_command((uint8_t) RADIO_SET_STANDBY, &standby_mode, 1); if (standby_mode == STDBY_RC) { _operation_mode = MODE_STDBY_RC; } else { _operation_mode = MODE_STDBY_XOSC; } } void SX126X_LoRaRadio::set_dio2_as_rfswitch_ctrl(uint8_t enable) { write_opmode_command(RADIO_SET_RFSWITCHMODE, &enable, 1); } void SX126X_LoRaRadio::set_dio3_as_tcxo_ctrl(radio_TCXO_ctrl_voltage_t voltage, uint32_t timeout) { uint8_t buf[4]; buf[0] = voltage & 0x07; buf[1] = (uint8_t) ((timeout >> 16) & 0xFF); buf[2] = (uint8_t) ((timeout >> 8) & 0xFF); buf[3] = (uint8_t) (timeout & 0xFF); write_opmode_command(RADIO_SET_TCXOMODE, buf, 4); } void SX126X_LoRaRadio::init_radio(radio_events_t *events) { _radio_events = events; // attach DIO1 interrupt line to its respective ISR _dio1_ctl.rise(callback(this, &SX126X_LoRaRadio::dio1_irq_isr)); uint8_t freq_support = get_frequency_support(); // Hold chip-select high _chip_select = 1; _spi.format(8, 0); _spi.frequency(SPI_FREQUENCY); // 100 us wait to settle down wait_us(100); radio_reset(); #if MBED_CONF_LORA_PUBLIC_NETWORK _network_mode_public = true; #else _network_mode_public = false; #endif // this is a POR sequence cold_start_wakeup(); } void SX126X_LoRaRadio::cold_start_wakeup() { uint8_t regulator_mode = MBED_CONF_SX126X_LORA_DRIVER_REGULATOR_MODE; write_opmode_command(RADIO_SET_REGULATORMODE, ®ulator_mode, 1); set_buffer_base_addr(0x00, 0x00); if (_crystal_select.is_connected() && _crystal_select == 0) { caliberation_params_t calib_param; set_dio3_as_tcxo_ctrl(TCXO_CTRL_1_7V, 320); //5 ms calib_param.value = 0x7F; write_opmode_command(RADIO_CALIBRATE, &calib_param.value, 1); } set_dio2_as_rfswitch_ctrl(true); _operation_mode = MODE_STDBY_RC; set_modem(_active_modem); if (_active_modem == MODEM_LORA) { set_public_network(_network_mode_public); } } void SX126X_LoRaRadio::set_public_network(bool enable) { if (enable) { // Change LoRa modem SyncWord write_to_register(REG_LR_SYNCWORD, (LORA_MAC_PUBLIC_SYNCWORD >> 8) & 0xFF); write_to_register(REG_LR_SYNCWORD + 1, LORA_MAC_PUBLIC_SYNCWORD & 0xFF); } else { // Change LoRa modem SyncWord write_to_register(REG_LR_SYNCWORD, (LORA_MAC_PRIVATE_SYNCWORD >> 8) & 0xFF); write_to_register(REG_LR_SYNCWORD + 1, LORA_MAC_PRIVATE_SYNCWORD & 0xFF); } } uint32_t SX126X_LoRaRadio::time_on_air(radio_modems_t modem, uint8_t pkt_len) { uint32_t air_time = 0; switch (modem) { case MODEM_FSK: { air_time = rint((8 * (_packet_params.params.gfsk.preamble_length + (_packet_params.params.gfsk.syncword_length >> 3) + ((_packet_params.params.gfsk.header_type == RADIO_PACKET_FIXED_LENGTH) ? 0.0f : 1.0f) + pkt_len + ((_packet_params.params.gfsk.crc_length == RADIO_CRC_2_BYTES) ? 2.0f : 0.0f)) / _mod_params.params.gfsk.bit_rate) * 1000); } break; case MODEM_LORA: { float ts = lora_symbol_time[_mod_params.params.lora.bandwidth - 4][12 - _mod_params.params.lora.spreading_factor]; // time of preamble float t_preamble = (_packet_params.params.lora.preamble_length + 4.25f) * ts; // Symbol length of payload and time float tmp = ceil((8 * pkt_len - 4 * _mod_params.params.lora.spreading_factor + 28 + 16 * _packet_params.params.lora.crc_mode - ((_packet_params.params.lora.header_type == LORA_PACKET_FIXED_LENGTH) ? 20 : 0)) / (float) (4 * (_mod_params.params.lora.spreading_factor - ((_mod_params.params.lora.low_datarate_optimization > 0) ? 2 : 0)))) * ((_mod_params.params.lora.coding_rate % 4) + 4); float n_payload = 8 + ((tmp > 0) ? tmp : 0); float t_payload = n_payload * ts; // Time on air float tOnAir = t_preamble + t_payload; // return milliseconds (as ts is in milliseconds) air_time = floor(tOnAir + 0.999); } break; } return air_time; } void SX126X_LoRaRadio::radio_reset() { _reset_ctl.output(); _reset_ctl = 0; // should be enough, required is 50-100 us wait_ms(2); _reset_ctl.input(); // give some time for automatic image calibration wait_ms(6); } void SX126X_LoRaRadio::wakeup() { // hold the NSS low, this should wakeup the chip. // now we should wait for the _busy line to go low if (_operation_mode == MODE_SLEEP) { _chip_select = 0; wait_us(100); _chip_select = 1; //wait_us(100); #if MBED_CONF_SX126X_LORA_DRIVER_SLEEP_MODE == 1 wait_us(3500); // whenever we wakeup from Cold sleep state, we need to perform // image calibration _force_image_calibration = true; cold_start_wakeup(); #endif } } void SX126X_LoRaRadio::sleep(void) { // warm start, power consumption 600 nA uint8_t sleep_state = 0x04; _operation_mode = MODE_SLEEP; #if MBED_CONF_SX126X_LORA_DRIVER_SLEEP_MODE == 1 // cold start, power consumption 160 nA sleep_state = 0x00; #endif write_opmode_command(RADIO_SET_SLEEP, &sleep_state, 1); wait_ms(2); } uint32_t SX126X_LoRaRadio::random(void) { set_modem(MODEM_LORA); uint8_t buf[] = {0, 0, 0, 0}; // Set radio in continuous reception _reception_mode = RECEPTION_MODE_OTHER; _rx_timeout = 0xFFFFFFFF; receive(); wait_ms(1); read_register(RANDOM_NUMBER_GENERATORBASEADDR, buf, 4); standby(); return (buf[0] << 24) | (buf[1] << 16) | (buf[2] << 8) | buf[3]; } void SX126X_LoRaRadio::write_opmode_command(uint8_t cmd, uint8_t *buffer, uint16_t size) { _chip_select = 0; while (_busy) { // do nothing } _spi.write(cmd); for (int i = 0; i < size; i++) { _spi.write(buffer[i]); } _chip_select = 1; } void SX126X_LoRaRadio::read_opmode_command(uint8_t cmd, uint8_t *buffer, uint16_t size) { _chip_select = 0; while (_busy) { // do nothing } _spi.write(cmd); _spi.write(0); for (int i = 0; i < size; i++) { buffer[i] = _spi.write(0); } _chip_select = 1; } void SX126X_LoRaRadio::write_to_register(uint16_t addr, uint8_t data) { write_to_register(addr, &data, 1); } void SX126X_LoRaRadio::write_to_register(uint16_t addr, uint8_t *data, uint8_t size) { _chip_select = 0; _spi.write(RADIO_WRITE_REGISTER); _spi.write((addr & 0xFF00) >> 8); _spi.write(addr & 0x00FF); for (int i = 0; i < size; i++) { _spi.write(data[i]); } _chip_select = 1; } uint8_t SX126X_LoRaRadio::read_register(uint16_t addr) { uint8_t data; read_register(addr, &data, 1); return data; } void SX126X_LoRaRadio::read_register(uint16_t addr, uint8_t *buffer, uint8_t size) { _chip_select = 0; _spi.write(RADIO_READ_REGISTER); _spi.write((addr & 0xFF00) >> 8); _spi.write(addr & 0x00FF); _spi.write(0); for (int i = 0; i < size; i++) { buffer[i] = _spi.write(0); } _chip_select = 1; } void SX126X_LoRaRadio::write_fifo(uint8_t *buffer, uint8_t size) { _chip_select = 0; _spi.write(RADIO_WRITE_BUFFER); _spi.write(0); for (int i = 0; i < size; i++) { _spi.write(buffer[i]); } _chip_select = 1; } void SX126X_LoRaRadio::set_modem(uint8_t modem) { _active_modem = modem; // setting modem type must happen in stnadby mode if (_operation_mode != MODE_STDBY_RC) { standby(); } write_opmode_command(RADIO_SET_PACKETTYPE, &_active_modem, 1); } uint8_t SX126X_LoRaRadio::get_modem() { return _active_modem; } void SX126X_LoRaRadio::read_fifo(uint8_t *buffer, uint8_t size, uint8_t offset) { _chip_select = 0; _spi.write(RADIO_READ_BUFFER); _spi.write(offset); _spi.write(0); for (int i = 0; i < size; i++) { buffer[i] = _spi.write(0); } _chip_select = 1; } uint8_t SX126X_LoRaRadio::get_device_variant(void) { uint16_t val = 0; val = _dev_select.read_u16(); if (val <= 0x2000) { return SX1262; } else if (val <= 0xA000) { return SX1268; } else { return SX1261; } } uint8_t SX126X_LoRaRadio::get_frequency_support(void) { uint16_t val = 0; val = _freq_select.read_u16(); if (val < 100) { return ( MATCHING_FREQ_915); } else if (val <= 0x3000) { return ( MATCHING_FREQ_780); } else if (val <= 0x4900) { // 0x4724 return ( MATCHING_FREQ_490); } else if (val <= 1) { return ( MATCHING_FREQ_434); } else if (val <= 1) { return ( MATCHING_FREQ_280); } else if (val <= 0xF000) { return ( MATCHING_FREQ_169); } else { return ( MATCHING_FREQ_868); } } uint8_t SX126X_LoRaRadio::get_fsk_bw_reg_val(uint32_t bandwidth) { uint8_t i; for (i = 0; i < (sizeof(fsk_bandwidths) / sizeof(fsk_bw_t)) - 1; i++) { if ((bandwidth >= fsk_bandwidths[i].bandwidth) && (bandwidth < fsk_bandwidths[i + 1].bandwidth)) { return fsk_bandwidths[i].register_value; } } // ERROR: Value not found // This should never happen while (1); } void SX126X_LoRaRadio::set_max_payload_length(radio_modems_t modem, uint8_t max) { if (modem == MODEM_LORA) { _packet_params.params.lora.payload_length = max; } else { _packet_params.params.gfsk.payload_length = max; } } void SX126X_LoRaRadio::set_tx_config(radio_modems_t modem, int8_t power, uint32_t fdev, uint32_t bandwidth, uint32_t datarate, uint8_t coderate, uint16_t preamble_len, bool fix_len, bool crc_on, bool freq_hop_on, uint8_t hop_period, bool iq_inverted, uint32_t timeout) { uint8_t modem_type = (uint8_t) modem; switch (modem_type) { case MODEM_FSK: _mod_params.modem_type = MODEM_FSK; _mod_params.params.gfsk.bit_rate = datarate; _mod_params.params.gfsk.modulation_shaping = MOD_SHAPING_G_BT_1; _mod_params.params.gfsk.bandwidth = get_fsk_bw_reg_val(bandwidth); _mod_params.params.gfsk.fdev = fdev; _packet_params.modem_type = MODEM_FSK; _packet_params.params.gfsk.preamble_length = (preamble_len << 3); // convert byte into bit _packet_params.params.gfsk.preamble_min_detect = RADIO_PREAMBLE_DETECTOR_08_BITS; _packet_params.params.gfsk.syncword_length = 3 << 3; // convert byte into bit _packet_params.params.gfsk.addr_comp = RADIO_ADDRESSCOMP_FILT_OFF; _packet_params.params.gfsk.header_type = (fix_len == true) ? RADIO_PACKET_FIXED_LENGTH : RADIO_PACKET_VARIABLE_LENGTH; if (crc_on) { _packet_params.params.gfsk.crc_length = RADIO_CRC_2_BYTES_CCIT; } else { _packet_params.params.gfsk.crc_length = RADIO_CRC_OFF; } _packet_params.params.gfsk.whitening_mode = RADIO_DC_FREEWHITENING; set_modem(MODEM_FSK); write_to_register(REG_LR_SYNCWORDBASEADDRESS, (uint8_t *) sync_word, 8); set_whitening_seed(0x01FF); break; case MODEM_LORA: _mod_params.modem_type = MODEM_LORA; _mod_params.params.lora.spreading_factor = (lora_spread_factors_t) datarate; _mod_params.params.lora.bandwidth = (lora_bandwidths_t) lora_bandwidhts[bandwidth]; _mod_params.params.lora.coding_rate = (lora_coding_tates_t) coderate; if (((bandwidth == 0) && ((datarate == 11) || (datarate == 12))) || ((bandwidth == 1) && (datarate == 12))) { _mod_params.params.lora.low_datarate_optimization = 0x01; } else { _mod_params.params.lora.low_datarate_optimization = 0x00; } _packet_params.modem_type = MODEM_LORA; if ((_mod_params.params.lora.spreading_factor == LORA_SF5) || (_mod_params.params.lora.spreading_factor == LORA_SF6)) { if (preamble_len < 12) { _packet_params.params.lora.preamble_length = 12; } else { _packet_params.params.lora.preamble_length = preamble_len; } } else { _packet_params.params.lora.preamble_length = preamble_len; } _packet_params.params.lora.header_type = (lora_pkt_length_t) fix_len; _packet_params.params.lora.crc_mode = (lora_crc_mode_t) crc_on; _packet_params.params.lora.invert_IQ = (lora_IQ_mode_t) iq_inverted; set_modem(MODEM_LORA); break; } _tx_power = power; _tx_timeout = timeout; } void SX126X_LoRaRadio::set_rx_config(radio_modems_t modem, uint32_t bandwidth, uint32_t datarate, uint8_t coderate, uint32_t bandwidthAfc, uint16_t preamble_len, uint16_t symb_timeout, bool fix_len, uint8_t payload_len, bool crc_on, bool freq_hop_on, uint8_t hop_period, bool iq_inverted, bool rx_continuous) { uint8_t max_payload_len; (void) freq_hop_on; (void) hop_period; if (rx_continuous) { _reception_mode = RECEPTION_MODE_CONTINUOUS; } else { _reception_mode = RECEPTION_MODE_SINGLE; } if (fix_len == true) { max_payload_len = payload_len; } else { max_payload_len = 0xFF; } uint8_t modem_type = (uint8_t) modem; switch (modem_type) { case MODEM_FSK: { _mod_params.modem_type = MODEM_FSK; _mod_params.params.gfsk.bit_rate = datarate; _mod_params.params.gfsk.modulation_shaping = MOD_SHAPING_G_BT_1; _mod_params.params.gfsk.bandwidth = get_fsk_bw_reg_val(bandwidth); _packet_params.modem_type = MODEM_FSK; _packet_params.params.gfsk.preamble_length = (preamble_len << 3); // convert byte into bit _packet_params.params.gfsk.preamble_min_detect = RADIO_PREAMBLE_DETECTOR_08_BITS; _packet_params.params.gfsk.syncword_length = 3 << 3; // convert byte into bit _packet_params.params.gfsk.addr_comp = RADIO_ADDRESSCOMP_FILT_OFF; _packet_params.params.gfsk.header_type = (fix_len == true) ? RADIO_PACKET_FIXED_LENGTH : RADIO_PACKET_VARIABLE_LENGTH; _packet_params.params.gfsk.payload_length = max_payload_len; if (crc_on) { _packet_params.params.gfsk.crc_length = RADIO_CRC_2_BYTES_CCIT; } else { _packet_params.params.gfsk.crc_length = RADIO_CRC_OFF; } _packet_params.params.gfsk.whitening_mode = RADIO_DC_FREEWHITENING; set_modem(MODEM_FSK); write_to_register(REG_LR_SYNCWORDBASEADDRESS, (uint8_t *) sync_word, 8); set_whitening_seed(0x01FF); _rx_timeout = (uint32_t) (symb_timeout * ((1.0 / (float) datarate) * 8.0) * 1000); break; } case MODEM_LORA: { _rx_timeout_in_symbols = symb_timeout; _mod_params.modem_type = MODEM_LORA; _mod_params.params.lora.spreading_factor = (lora_spread_factors_t) datarate; _mod_params.params.lora.bandwidth = (lora_bandwidths_t) lora_bandwidhts[bandwidth]; _mod_params.params.lora.coding_rate = (lora_coding_tates_t) coderate; if (((bandwidth == 0) && ((datarate == 11) || (datarate == 12))) || ((bandwidth == 1) && (datarate == 12))) { _mod_params.params.lora.low_datarate_optimization = 0x01; } else { _mod_params.params.lora.low_datarate_optimization = 0x00; } _packet_params.modem_type = MODEM_LORA; if ((_mod_params.params.lora.spreading_factor == LORA_SF5) || (_mod_params.params.lora.spreading_factor == LORA_SF6)) { if (preamble_len < 12) { _packet_params.params.lora.preamble_length = 12; } else { _packet_params.params.lora.preamble_length = preamble_len; } } else { _packet_params.params.lora.preamble_length = preamble_len; } _packet_params.params.lora.header_type = (lora_pkt_length_t) fix_len; _packet_params.params.lora.payload_length = max_payload_len; _packet_params.params.lora.crc_mode = (lora_crc_mode_t) crc_on; _packet_params.params.lora.invert_IQ = (lora_IQ_mode_t) iq_inverted; set_modem(MODEM_LORA); if (_reception_mode == RECEPTION_MODE_CONTINUOUS) { _rx_timeout = 0xFFFFFFFF; } else { _rx_timeout = 0x00000000; } break; } default: break; } } void SX126X_LoRaRadio::configure_dio_irq(uint16_t irq_mask, uint16_t dio1_mask, uint16_t dio2_mask, uint16_t dio3_mask) { uint8_t buf[8]; buf[0] = (uint8_t) ((irq_mask >> 8) & 0x00FF); buf[1] = (uint8_t) (irq_mask & 0x00FF); buf[2] = (uint8_t) ((dio1_mask >> 8) & 0x00FF); buf[3] = (uint8_t) (dio1_mask & 0x00FF); buf[4] = (uint8_t) ((dio2_mask >> 8) & 0x00FF); buf[5] = (uint8_t) (dio2_mask & 0x00FF); buf[6] = (uint8_t) ((dio3_mask >> 8) & 0x00FF); buf[7] = (uint8_t) (dio3_mask & 0x00FF); write_opmode_command((uint8_t) RADIO_CFG_DIOIRQ, buf, 8); } void SX126X_LoRaRadio::send(uint8_t *buffer, uint8_t size) { set_tx_power(_tx_power); configure_dio_irq(IRQ_TX_DONE | IRQ_RX_TX_TIMEOUT, IRQ_TX_DONE | IRQ_RX_TX_TIMEOUT, IRQ_RADIO_NONE, IRQ_RADIO_NONE ); set_modulation_params(&_mod_params); set_packet_params(&_packet_params); write_fifo(buffer, size); uint8_t buf[3]; // _tx_timeout in ms should be converted to us and then divided by // 15.625 us. Check data-sheet 13.1.4 SetTX() section. uint32_t timeout_scalled = ceil((_tx_timeout * 1000) / 15.625); buf[0] = (uint8_t) ((timeout_scalled >> 16) & 0xFF); buf[1] = (uint8_t) ((timeout_scalled >> 8) & 0xFF); buf[2] = (uint8_t) (timeout_scalled & 0xFF); write_opmode_command(RADIO_SET_TX, buf, 3); _operation_mode = MODE_TX; } void SX126X_LoRaRadio::receive(void) { if (get_modem() == MODEM_LORA && _reception_mode != RECEPTION_MODE_CONTINUOUS) { // Data-sheet Table 13-11: StopOnPreambParam // We will use radio's internal timer to mark no reception. This behaviour // is different from SX1272/SX1276 where we are relying on radio to stop // at preamble detection. // 0x00 means Timer will be stopped on SyncWord(FSK) or Header (LoRa) detection // 0x01 means Timer is stopped on preamble detection uint8_t stop_at_preamble = 0x01; write_opmode_command(RADIO_SET_STOPRXTIMERONPREAMBLE, &stop_at_preamble, 1); // Data-sheet 13.4.9 SetLoRaSymbNumTimeout write_opmode_command(RADIO_SET_LORASYMBTIMEOUT, &_rx_timeout_in_symbols, 1); } if (_reception_mode != RECEPTION_MODE_OTHER) { configure_dio_irq(IRQ_RX_DONE | IRQ_RX_TX_TIMEOUT | IRQ_CRC_ERROR , IRQ_RX_DONE | IRQ_RX_TX_TIMEOUT | IRQ_CRC_ERROR , IRQ_RADIO_NONE, IRQ_RADIO_NONE); set_modulation_params(&_mod_params); set_packet_params(&_packet_params); } uint8_t buf[3]; #if MBED_CONF_SX126X_LORA_DRIVER_BOOST_RX write_to_register(REG_RX_GAIN, 0x96); #endif buf[0] = (uint8_t) ((_rx_timeout >> 16) & 0xFF); buf[1] = (uint8_t) ((_rx_timeout >> 8) & 0xFF); buf[2] = (uint8_t) (_rx_timeout & 0xFF); write_opmode_command(RADIO_SET_RX, buf, 3); _operation_mode = MODE_RX; } // check data-sheet 13.1.14.1 PA optimal settings void SX126X_LoRaRadio::set_tx_power(int8_t power) { uint8_t buf[2]; if (get_device_variant() == SX1261) { if (power >= 14) { set_pa_config(0x04, 0x00, 0x01, 0x01); power = 14; } else if (power < 14){ set_pa_config(0x01, 0x00, 0x01, 0x01); } if (power < -3) { power = -3; } write_to_register(REG_OCP, 0x18); // current max is 80 mA for the whole device } else { // sx1262 or sx1268 if (power > 22) { power = 22; } else if (power < -3) { power = -3; } if (power <= 14) { set_pa_config(0x02, 0x02, 0x00, 0x01); } else { set_pa_config(0x04, 0x07, 0x00, 0x01); } write_to_register(REG_OCP, 0x38); // current max 160mA for the whole device } buf[0] = power; if (_crystal_select.is_connected() && _crystal_select == 0) { // TCXO buf[1] = RADIO_RAMP_200_US; } else { // XTAL buf[1] = RADIO_RAMP_20_US; } write_opmode_command(RADIO_SET_TXPARAMS, buf, 2); } void SX126X_LoRaRadio::set_modulation_params(modulation_params_t *params) { uint8_t n; uint32_t temp = 0; uint8_t buf[8] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00}; // Check if required configuration corresponds to the stored packet type // If not, silently update radio packet type if (_active_modem != params->modem_type) { set_modem(params->modem_type); } switch (params->modem_type) { case MODEM_FSK: n = 8; temp = (uint32_t) (32 * ((float) XTAL_FREQ / (float) params->params.gfsk.bit_rate)); buf[0] = (temp >> 16) & 0xFF; buf[1] = (temp >> 8) & 0xFF; buf[2] = temp & 0xFF; buf[3] = params->params.gfsk.modulation_shaping; buf[4] = params->params.gfsk.bandwidth; temp = (uint32_t) ((float) params->params.gfsk.fdev / (float) FREQ_STEP); buf[5] = (temp >> 16) & 0xFF; buf[6] = (temp >> 8) & 0xFF; buf[7] = (temp & 0xFF); write_opmode_command(RADIO_SET_MODULATIONPARAMS, buf, n); break; case MODEM_LORA: n = 4; buf[0] = params->params.lora.spreading_factor; buf[1] = params->params.lora.bandwidth; buf[2] = params->params.lora.coding_rate; buf[3] = params->params.lora.low_datarate_optimization; write_opmode_command(RADIO_SET_MODULATIONPARAMS, buf, n); break; default: return; } } void SX126X_LoRaRadio::set_pa_config(uint8_t pa_DC, uint8_t hp_max, uint8_t device_type, uint8_t pa_LUT ) { uint8_t buf[4]; buf[0] = pa_DC; buf[1] = hp_max; buf[2] = device_type; buf[3] = pa_LUT; write_opmode_command(RADIO_SET_PACONFIG, buf, 4); } void SX126X_LoRaRadio::set_crc_seed(uint16_t seed) { if (_active_modem == MODEM_FSK) { uint8_t buf[2]; buf[0] = (uint8_t) ((seed >> 8) & 0xFF); buf[1] = (uint8_t) (seed & 0xFF); write_to_register(REG_LR_CRCSEEDBASEADDR, buf, 2); } } void SX126X_LoRaRadio::set_crc_polynomial(uint16_t polynomial) { if (_active_modem == MODEM_FSK) { uint8_t buf[2]; buf[0] = (uint8_t) ((polynomial >> 8) & 0xFF); buf[1] = (uint8_t) (polynomial & 0xFF); write_to_register(REG_LR_CRCPOLYBASEADDR, buf, 2); } } void SX126X_LoRaRadio::set_whitening_seed(uint16_t seed) { if (_active_modem == MODEM_FSK) { uint8_t reg_value = read_register(REG_LR_WHITSEEDBASEADDR_MSB) & 0xFE; reg_value = ((seed >> 8) & 0x01) | reg_value; write_to_register(REG_LR_WHITSEEDBASEADDR_MSB, reg_value); // only 1 bit. write_to_register(REG_LR_WHITSEEDBASEADDR_LSB, (uint8_t) seed); } } void SX126X_LoRaRadio::set_packet_params(packet_params_t *packet_params) { uint8_t n; uint8_t crc_val = 0; uint8_t buf[9] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00}; // Check if required configuration corresponds to the stored packet type // If not, silently update radio packet type if (_active_modem != packet_params->modem_type) { set_modem(packet_params->modem_type); } switch (packet_params->modem_type) { case MODEM_FSK: if (packet_params->params.gfsk.crc_length == RADIO_CRC_2_BYTES_IBM) { set_crc_seed(CRC_IBM_SEED); set_crc_polynomial(CRC_POLYNOMIAL_IBM); crc_val = RADIO_CRC_2_BYTES; } else if (packet_params->params.gfsk.crc_length == RADIO_CRC_2_BYTES_CCIT) { set_crc_seed(CRC_CCITT_SEED); set_crc_polynomial(CRC_POLYNOMIAL_CCITT); crc_val = RADIO_CRC_2_BYTES_INV; } else { crc_val = packet_params->params.gfsk.crc_length; } n = 9; buf[0] = (packet_params->params.gfsk.preamble_length >> 8) & 0xFF; buf[1] = packet_params->params.gfsk.preamble_length; buf[2] = packet_params->params.gfsk.preamble_min_detect; buf[3] = (packet_params->params.gfsk.syncword_length /*<< 3*/); // convert from byte to bit buf[4] = packet_params->params.gfsk.addr_comp; buf[5] = packet_params->params.gfsk.header_type; buf[6] = packet_params->params.gfsk.payload_length; buf[7] = crc_val; buf[8] = packet_params->params.gfsk.whitening_mode; break; case MODEM_LORA: n = 6; buf[0] = (packet_params->params.lora.preamble_length >> 8) & 0xFF; buf[1] = packet_params->params.lora.preamble_length; buf[2] = packet_params->params.lora.header_type; buf[3] = packet_params->params.lora.payload_length; buf[4] = packet_params->params.lora.crc_mode; buf[5] = packet_params->params.lora.invert_IQ; break; default: return; } write_opmode_command(RADIO_SET_PACKETPARAMS, buf, n); } void SX126X_LoRaRadio::set_cad_params(lora_cad_symbols_t nb_symbols, uint8_t det_peak, uint8_t det_min, cad_exit_modes_t exit_mode, uint32_t timeout) { uint8_t buf[7]; buf[0] = (uint8_t) nb_symbols; buf[1] = det_peak; buf[2] = det_min; buf[3] = (uint8_t) exit_mode; buf[4] = (uint8_t) ((timeout >> 16) & 0xFF); buf[5] = (uint8_t) ((timeout >> 8) & 0xFF); buf[6] = (uint8_t) (timeout & 0xFF); write_opmode_command((uint8_t) RADIO_SET_CADPARAMS, buf, 7); _operation_mode = MODE_CAD; } void SX126X_LoRaRadio::set_buffer_base_addr(uint8_t tx_base_addr, uint8_t rx_base_addr) { uint8_t buf[2]; buf[0] = tx_base_addr; buf[1] = rx_base_addr; write_opmode_command((uint8_t) RADIO_SET_BUFFERBASEADDRESS, buf, 2); } uint8_t SX126X_LoRaRadio::get_status(void) { if (_operation_mode != MODE_STDBY_RC || _operation_mode != MODE_SLEEP) { return 0; } return 0xFF; } int8_t SX126X_LoRaRadio::get_rssi() { uint8_t buf[1]; int8_t rssi = 0; read_opmode_command((uint8_t) RADIO_GET_RSSIINST, buf, 1); rssi = -buf[0] >> 1; return rssi; } void SX126X_LoRaRadio::get_rx_buffer_status(uint8_t *payload_len, uint8_t *start_ptr) { uint8_t status[2]; read_opmode_command((uint8_t) RADIO_GET_RXBUFFERSTATUS, status, 2); // In case of LORA fixed header, the payloadLength is obtained by reading // the register REG_LR_PAYLOADLENGTH if ((get_modem() == MODEM_LORA) && (read_register(REG_LR_PACKETPARAMS) >> 7 == 1)) { *payload_len = read_register(REG_LR_PAYLOADLENGTH); } else { *payload_len = status[0]; } *start_ptr = status[1]; } void SX126X_LoRaRadio::get_packet_status(packet_status_t *pkt_status) { uint8_t status[3]; read_opmode_command((uint8_t) RADIO_GET_PACKETSTATUS, status, 3); pkt_status->modem_type = (radio_modems_t) get_modem(); switch (pkt_status->modem_type) { case MODEM_FSK: pkt_status->params.gfsk.rx_status = status[0]; pkt_status->params.gfsk.rssi_sync = -status[1] >> 1; pkt_status->params.gfsk.rssi_avg = -status[2] >> 1; pkt_status->params.gfsk.freq_error = 0; break; case MODEM_LORA: pkt_status->params.lora.rssi_pkt = -status[0] >> 1; // Returns SNR value [dB] rounded to the nearest integer value pkt_status->params.lora.snr_pkt = (((int8_t) status[1]) + 2) >> 2; pkt_status->params.lora.signal_rssi_pkt = -status[2] >> 1; break; default: // In that specific case, we set everything in the pkt_status to zeros // and reset the packet type accordingly memset(pkt_status, 0, sizeof(packet_status_t)); break; } } radio_error_t SX126X_LoRaRadio::get_device_errors(void) { radio_error_t error; read_opmode_command((uint8_t) RADIO_GET_ERROR, (uint8_t *)&error, 2); return error; } void SX126X_LoRaRadio::clear_device_errors(void) { uint8_t buf[2] = {0x00, 0x00}; write_opmode_command((uint8_t) RADIO_CLR_ERROR, buf, 2); }