brian claus
Copied from STs implementation.
Diff: lis3mdl_platform.h
- Revision:
- 0:32f3441153b5
- Child:
- 1:898554a35638
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/lis3mdl_platform.h Thu Oct 06 16:45:48 2016 +0000
@@ -0,0 +1,364 @@
+/**
+ ******************************************************************************
+ * @file lis3mdl.h
+ * @author MEMS Application Team
+ * @version V1.0.0
+ * @date 30-July-2014
+ * @brief This file contains definitions for the lis3mdl.c
+ * firmware driver.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __LIS3MDL_PLATFORM_H
+#define __LIS3MDL_PLATFORM_H
+
+
+/** @addtogroup LIS3MDL
+ * @{
+ */
+
+/** @defgroup LIS3MDL_Exported_Constants
+ * @{
+ */
+
+
+
+/******************************************************************************/
+/***************** START MAGNETIC SENSOR REGISTER MAPPING ********************/
+/******************************************************************************/
+
+/**
+ * @brief Device identifier register.
+ * \code
+ * Read
+ * Default value:
+ * 7:0 This read-only register contains the device identifier
+ * \endcode
+*/
+#define LIS3MDL_M_WHO_AM_I_ADDR 0x0F
+
+
+/**
+ * @brief Magnetic sensor Control Register 1
+ * \code
+ * Read/write
+ * Default value: 0x10
+ * [7] TEMP_COMP: Temperature compensation enable
+ * [6:5] OM1-0: X and Y axes operative mode selection
+ * [4:2] DO2-0: Output data rate selection
+ * [1] This bit must be set to �0� for the correct operation of the device
+ * [0] ST: Self-test enable
+ * \endcode
+ */
+#define LIS3MDL_M_CTRL_REG1_M 0x20
+
+
+/**
+ * @brief Magnetic sensor Control Register 2
+ * \code
+ * Read/write
+ * Default value: 0x00
+ * [7] These bits must be set to �0� for the correct operation of the device
+ * [6:5] FS1-0: Full-scale configuration
+ * [4] These bits must be set to �0� for the correct operation of the device
+ * [3] REBOOT: Reboot memory content
+ * [2] SOFT_RST: Configuration registers and user register reset function
+ * [1:0] These bits must be set to �0� for the correct operation of the device
+ * \endcode
+ */
+#define LIS3MDL_M_CTRL_REG2_M 0x21
+
+
+/**
+ * @brief Magnetic sensor Control Register 3
+ * \code
+ * Read/write
+ * Default value: 0x03
+ * [7] I2C_DISABLE: Disable I2C interface
+ * [6] These bits must be set to �0� for the correct operation of the device
+ * [5] LP: Low-power mode configuration
+ * [4:3] These bits must be set to �0� for the correct operation of the device
+ * [2] SIM: SPI Serial Interface mode selection
+ * [1:0] MD1-0: Operating mode selection
+ * \endcode
+ */
+#define LIS3MDL_M_CTRL_REG3_M 0x22
+
+
+/**
+ * @brief Magnetic sensor data (LSB)
+ * \code
+ * Read
+ * \endcode
+ */
+#define LIS3MDL_M_OUT_X_L_M 0x28
+
+
+/**
+ * @brief Magnetic sensor data (MSB)
+ * \code
+ * Read
+ * \endcode
+ */
+#define LIS3MDL_M_OUT_X_H_M 0x29
+
+
+/**
+ * @brief Magnetic sensor data (LSB)
+ * \code
+ * Read
+ * \endcode
+ */
+#define LIS3MDL_M_OUT_Y_L_M 0x2A
+
+
+/**
+ * @brief Magnetic sensor data (MSB)
+ * \code
+ * Read
+ * \endcode
+ */
+#define LIS3MDL_M_OUT_Y_H_M 0x2B
+
+
+/**
+ * @brief Magnetic sensor data (LSB)
+ * \code
+ * Read
+ * \endcode
+ */
+#define LIS3MDL_M_OUT_Z_L_M 0x2C
+
+
+/**
+ * @brief Magnetic sensor data (MSB)
+ * \code
+ * Read
+ * \endcode
+ */
+#define LIS3MDL_M_OUT_Z_H_M 0x2D
+
+
+/**
+ * @brief Magnetic sensor Interrupt config register
+ * \code
+ * Read/write
+ * Default value: 0x00
+ * [7] XIEN: Enable interrupt generation on X axis
+ * [6] YIEN: Enable interrupt generation on Y axis
+ * [5] ZIEN: Enable interrupt generation on Z axis
+ * [4:3] Must be 0
+ * [2] IEA: Interrupt active configuration on INT
+ * [1] LIR: Latch interrupt request
+ * [0] IEN: Interrupt enable on INT pin
+ * \endcode
+ */
+#define LIS3MDL_M_INT_CFG 0x30
+
+
+/**
+ * @brief Magnetic sensor Interrupt source register
+ * \code
+ * Read/write
+ * Default value: 0x00
+ * [7] PTH_X: Value on X-axis exceeds the threshold on the positive side
+ * [6] PTH_Y: Value on Y-axis exceeds the threshold on the positive side
+ * [5] PTH_Z: Value on Z-axis exceeds the threshold on the positive side
+ * [4] NTH_X: Value on X-axis exceeds the threshold on the negative side
+ * [3] NTH_Y: Value on Y-axis exceeds the threshold on the negative side
+ * [2] NTH_Z: Value on Z-axis exceeds the threshold on the negative side
+ * [1] MROI: Internal measurement range overflow on magnetic value
+ * [0] INT: This bit signals when interrupt event occours
+ * \endcode
+ */
+#define LIS3MDL_M_INT_SRC 0x31
+
+
+/**
+ * @brief Magnetic sensor Interrupt threshold register low
+ * \code
+ * Read/write
+ * Default value: 0x00
+ * [7:0] THS7-0: Least 8 significant bits of interrupt threshold
+ * \endcode
+ */
+#define LIS3MDL_M_INT_THS_L_M 0x32
+
+
+/**
+ * @brief Magnetic sensor Interrupt threshold register high
+ * \code
+ * Read/write
+ * Default value: 0x00
+ * [7] Must be 0
+ * [6:0] THS14-8: Most 7 significant bits of interrupt threshold
+ * \endcode
+ */
+#define LIS3MDL_M_INT_THS_H_M 0x33
+
+/******************************************************************************/
+/******************* END MAGNETIC SENSOR REGISTER MAPPING ********************/
+/******************************************************************************/
+
+
+
+/**
+ * @brief Device Address
+ */
+
+#define LIS3MDL_M_MEMS_ADDRESS 0x3C // SAD[1] = 1
+
+/**
+ * @brief Device Identifier. Default value of the WHO_AM_I register.
+ */
+#define I_AM_LIS3MDL_M ((uint8_t)0x3D)
+
+
+/*********************************** MAGNETIC SENSOR REGISTERS VALUE ****************************************/
+
+/** @defgroup LIS3MDL_M Temperature compensation enable selection CTRL_REG1_M
+ * @{
+ */
+#define LIS3MDL_M_TEMP_COMP_DISABLE ((uint8_t)0x00) /*!< Temperature compensation: disable */
+#define LIS3MDL_M_TEMP_COMP_ENABLE ((uint8_t)0x80) /*!< Temperature compensation: enable */
+
+#define LIS3MDL_M_TEMP_COMP_MASK ((uint8_t)0x80)
+
+
+/** @defgroup LIS3MDL_M X and Y axes operative mode selection CTRL_REG1_M
+ * @{
+ */
+#define LIS3MDL_M_OM_LP ((uint8_t)0x00) /*!< X and Y axes operative mode: Low-power mode */
+#define LIS3MDL_M_OM_MP ((uint8_t)0x20) /*!< X and Y axes operative mode: Medium-performance mode */
+#define LIS3MDL_M_OM_HP ((uint8_t)0x40) /*!< X and Y axes operative mode: High-performance mode */
+#define LIS3MDL_M_OM_UHP ((uint8_t)0x60) /*!< X and Y axes operative mode: Ultra-high performance mode */
+
+#define LIS3MDL_M_OM_MASK ((uint8_t)0x60)
+
+
+/** @defgroup LIS3MDL_M Output data rate selection CTRL_REG1_M
+ * @{
+ */
+#define LIS3MDL_M_DO_0_625 ((uint8_t)0x00) /*!< Output data rate selection: 0.625 */
+#define LIS3MDL_M_DO_1_25 ((uint8_t)0x04) /*!< Output data rate selection: 1.25 */
+#define LIS3MDL_M_DO_2_5 ((uint8_t)0x08) /*!< Output data rate selection: 2.5 */
+#define LIS3MDL_M_DO_5 ((uint8_t)0x0C) /*!< Output data rate selection: 5 */
+#define LIS3MDL_M_DO_10 ((uint8_t)0x10) /*!< Output data rate selection: 10 */
+#define LIS3MDL_M_DO_20 ((uint8_t)0x14) /*!< Output data rate selection: 20 */
+#define LIS3MDL_M_DO_40 ((uint8_t)0x18) /*!< Output data rate selection: 40 */
+#define LIS3MDL_M_DO_80 ((uint8_t)0x1C) /*!< Output data rate selection: 80 */
+
+#define LIS3MDL_M_DO_MASK ((uint8_t)0x1C)
+
+
+/** @defgroup LIS3MDL_M Self-test enable selection CTRL_REG1_M
+ * @{
+ */
+#define LIS3MDL_M_ST_DISABLE ((uint8_t)0x00) /*!< Self-test: disable */
+#define LIS3MDL_M_ST_ENABLE ((uint8_t)0x01) /*!< Self-test: enable */
+
+#define LIS3MDL_M_ST_MASK ((uint8_t)0x01)
+
+
+/** @defgroup LIS3MDL_M Full scale selection CTRL_REG2_M
+ * @{
+ */
+#define LIS3MDL_M_FS_4 ((uint8_t)0x00) /*!< Full scale: +-4 guass */
+#define LIS3MDL_M_FS_8 ((uint8_t)0x20) /*!< Full scale: +-8 gauss */
+#define LIS3MDL_M_FS_12 ((uint8_t)0x40) /*!< Full scale: +-12 gauss */
+#define LIS3MDL_M_FS_16 ((uint8_t)0x60) /*!< Full scale: +-16 gauss */
+
+#define LIS3MDL_M_FS_MASK ((uint8_t)0x60)
+
+
+/** @defgroup LIS3MDL_M Reboot memory selection CTRL_REG2_M
+ * @{
+ */
+#define LIS3MDL_M_REBOOT_NORMAL ((uint8_t)0x00) /*!< Reboot mode: normal mode */
+#define LIS3MDL_M_REBOOT_MEM_CONTENT ((uint8_t)0x08) /*!< Reboot mode: reboot memory content */
+
+#define LIS3MDL_M_REBOOT_MASK ((uint8_t)0x08)
+
+
+/** @defgroup LIS3MDL_M Configuration registers and user register reset CTRL_REG2_M
+ * @{
+ */
+#define LIS3MDL_M_SOFT_RST_DEFAULT ((uint8_t)0x00) /*!< Reset function: default value */
+#define LIS3MDL_M_SOFT_RST_RESET ((uint8_t)0x04) /*!< Reset function: reset operation */
+
+#define LIS3MDL_M_SOFT_RST_MASK ((uint8_t)0x04)
+
+
+/** @defgroup LIS3MDL_M Disable I2C interface selection CTRL_REG3_M
+ * @{
+ */
+#define LIS3MDL_M_I2C_ENABLE ((uint8_t)0x00) /*!< I2C interface: enable */
+#define LIS3MDL_M_I2C_DISABLE ((uint8_t)0x80) /*!< I2C interface: disable */
+
+#define LIS3MDL_M_I2C_MASK ((uint8_t)0x80)
+
+
+/** @defgroup LIS3MDL_M Low-power mode selection CTRL_REG3_M
+ * @{
+ */
+#define LIS3MDL_M_LP_ENABLE ((uint8_t)0x00) /*!< Low-power mode: magnetic data rate is configured by
+ the DO bits in the CTRL_REG1_M */
+#define LIS3MDL_M_LP_DISABLE ((uint8_t)0x20) /*!< Low-power mode: the DO bits is set to 0.625 Hz and the system performs,
+ for each channel, the minimum number of averages */
+
+#define LIS3MDL_M_LP_MASK ((uint8_t)0x20)
+
+
+/** @defgroup LIS3MDL_M SPI Serial Interface mode selection CTRL_REG3_M
+ * @{
+ */
+#define LIS3MDL_M_SPI_R_ENABLE ((uint8_t)0x00) /*!< SPI Serial Interface mode: only write operations enabled */
+#define LIS3MDL_M_SPI_R_DISABLE ((uint8_t)0x40) /*!< SPI Serial Interface mode: read and write operations enable */
+
+#define LIS3MDL_M_SPI_R_MASK ((uint8_t)0x40)
+
+
+/** @defgroup LIS3MDL_M Operating mode selection CTRL_REG3_M
+ * @{
+ */
+#define LIS3MDL_M_MD_CONTINUOUS ((uint8_t)0x00) /*!< Operating mode: Continuous-conversion mode */
+#define LIS3MDL_M_MD_SINGLE ((uint8_t)0x01) /*!< Operating mode: Single-conversion mode has to be used with sampling frequency from 0.625 Hz to 80 Hz. */
+#define LIS3MDL_M_MD_PD ((uint8_t)0x02) /*!< Operating mode: Power-down mode */
+
+#define LIS3MDL_M_MD_MASK ((uint8_t)0x03)
+
+
+
+
+#endif /* __LIS3MDL_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+