Diff: Classes/EncoderCounter.cpp

Revision:

0:b886f13e4ac6

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/Classes/EncoderCounter.cpp	Sun Apr 22 16:14:54 2018 +0000
@@ -0,0 +1,169 @@
+/*
+ * EncoderCounter.cpp
+ * Copyright (c) 2018, ZHAW
+ * All rights reserved.
+ */
+
+#include "EncoderCounter.h"
+
+using namespace std;
+
+/**
+ * Creates and initializes the driver to read the quadrature
+ * encoder counter of the STM32 microcontroller.
+ * @param a the input pin for the channel A.
+ * @param b the input pin for the channel B.
+ */
+EncoderCounter::EncoderCounter(PinName a, PinName b) {
+    
+    // check pins
+    
+    if ((a == PA_0) && (b == PA_1)) {
+        
+        // pinmap OK for TIM2 CH1 and CH2
+        
+        TIM = TIM2;
+        
+        // configure general purpose I/O registers
+        
+        GPIOA->MODER &= ~GPIO_MODER_MODER0;     // reset port A0
+        GPIOA->MODER |= GPIO_MODER_MODER0_1;    // set alternate mode of port A0
+        GPIOA->PUPDR &= ~GPIO_PUPDR_PUPDR0;     // reset pull-up/pull-down on port A0
+        GPIOA->PUPDR |= GPIO_PUPDR_PUPDR0_1;    // set input as pull-down
+        GPIOA->AFR[0] &= ~(0xF << 4*0);         // reset alternate function of port A0
+        GPIOA->AFR[0] |= 1 << 4*0;              // set alternate funtion 1 of port A0
+        
+        GPIOA->MODER &= ~GPIO_MODER_MODER1;     // reset port A1
+        GPIOA->MODER |= GPIO_MODER_MODER1_1;    // set alternate mode of port A1
+        GPIOA->PUPDR &= ~GPIO_PUPDR_PUPDR1;     // reset pull-up/pull-down on port A1
+        GPIOA->PUPDR |= GPIO_PUPDR_PUPDR1_1;    // set input as pull-down
+        GPIOA->AFR[0] &= ~(0xF << 4*1);         // reset alternate function of port A1
+        GPIOA->AFR[0] |= 1 << 4*1;              // set alternate funtion 1 of port A1
+        
+        // configure reset and clock control registers
+        
+        RCC->APB1RSTR |= RCC_APB1RSTR_TIM2RST;  //reset TIM2 controller
+        RCC->APB1RSTR &= ~RCC_APB1RSTR_TIM2RST;
+        
+        RCC->APB1ENR |= RCC_APB1ENR_TIM2EN;     // TIM2 clock enable
+        
+    } else if ((a == PA_6) && (b == PC_7)) {
+        
+        // pinmap OK for TIM3 CH1 and CH2
+        
+        TIM = TIM3;
+        
+        // configure reset and clock control registers
+        
+        RCC->AHB1ENR |= RCC_AHB1ENR_GPIOCEN;    // manually enable port C (port A enabled by mbed library)
+        
+        // configure general purpose I/O registers
+        
+        GPIOA->MODER &= ~GPIO_MODER_MODER6;     // reset port A6
+        GPIOA->MODER |= GPIO_MODER_MODER6_1;    // set alternate mode of port A6
+        GPIOA->PUPDR &= ~GPIO_PUPDR_PUPDR6;     // reset pull-up/pull-down on port A6
+        GPIOA->PUPDR |= GPIO_PUPDR_PUPDR6_1;    // set input as pull-down
+        GPIOA->AFR[0] &= ~(0xF << 4*6);         // reset alternate function of port A6
+        GPIOA->AFR[0] |= 2 << 4*6;              // set alternate funtion 2 of port A6
+        
+        GPIOC->MODER &= ~GPIO_MODER_MODER7;     // reset port C7
+        GPIOC->MODER |= GPIO_MODER_MODER7_1;    // set alternate mode of port C7
+        GPIOC->PUPDR &= ~GPIO_PUPDR_PUPDR7;     // reset pull-up/pull-down on port C7
+        GPIOC->PUPDR |= GPIO_PUPDR_PUPDR7_1;    // set input as pull-down
+        GPIOC->AFR[0] &= ~0xF0000000;           // reset alternate function of port C7
+        GPIOC->AFR[0] |= 2 << 4*7;              // set alternate funtion 2 of port C7
+        
+        // configure reset and clock control registers
+        
+        RCC->APB1RSTR |= RCC_APB1RSTR_TIM3RST;  //reset TIM3 controller
+        RCC->APB1RSTR &= ~RCC_APB1RSTR_TIM3RST;
+        
+        RCC->APB1ENR |= RCC_APB1ENR_TIM3EN;     // TIM3 clock enable
+        
+    } else if ((a == PB_6) && (b == PB_7)) {
+        
+        // pinmap OK for TIM4 CH1 and CH2
+        
+        TIM = TIM4;
+        
+        // configure reset and clock control registers
+        
+        RCC->AHB1ENR |= RCC_AHB1ENR_GPIOBEN;    // manually enable port B (port A enabled by mbed library)
+        
+        // configure general purpose I/O registers
+        
+        GPIOB->MODER &= ~GPIO_MODER_MODER6;     // reset port B6
+        GPIOB->MODER |= GPIO_MODER_MODER6_1;    // set alternate mode of port B6
+        GPIOB->PUPDR &= ~GPIO_PUPDR_PUPDR6;     // reset pull-up/pull-down on port B6
+        GPIOB->PUPDR |= GPIO_PUPDR_PUPDR6_1;    // set input as pull-down
+        GPIOB->AFR[0] &= ~(0xF << 4*6);         // reset alternate function of port B6
+        GPIOB->AFR[0] |= 2 << 4*6;              // set alternate funtion 2 of port B6
+        
+        GPIOB->MODER &= ~GPIO_MODER_MODER7;     // reset port B7
+        GPIOB->MODER |= GPIO_MODER_MODER7_1;    // set alternate mode of port B7
+        GPIOB->PUPDR &= ~GPIO_PUPDR_PUPDR7;     // reset pull-up/pull-down on port B7
+        GPIOB->PUPDR |= GPIO_PUPDR_PUPDR7_1;    // set input as pull-down
+        GPIOB->AFR[0] &= ~0xF0000000;           // reset alternate function of port B7
+        GPIOB->AFR[0] |= 2 << 4*7;              // set alternate funtion 2 of port B7
+        
+        // configure reset and clock control registers
+        
+        RCC->APB1RSTR |= RCC_APB1RSTR_TIM4RST;  //reset TIM4 controller
+        RCC->APB1RSTR &= ~RCC_APB1RSTR_TIM4RST;
+        
+        RCC->APB1ENR |= RCC_APB1ENR_TIM4EN;     // TIM4 clock enable
+        
+    } else {
+        
+        printf("pinmap not found for peripheral\n");
+    }
+    
+    // configure general purpose timer 3 or 4
+    
+    TIM->CR1 = 0x0000;          // counter disable
+    TIM->CR2 = 0x0000;          // reset master mode selection
+    TIM->SMCR = TIM_SMCR_SMS_1 | TIM_SMCR_SMS_0; // counting on both TI1 & TI2 edges
+    TIM->CCMR1 = TIM_CCMR1_CC2S_0 | TIM_CCMR1_CC1S_0;
+    TIM->CCMR2 = 0x0000;        // reset capture mode register 2
+    TIM->CCER = TIM_CCER_CC2E | TIM_CCER_CC1E;
+    TIM->CNT = 0x0000;          // reset counter value
+    TIM->ARR = 0xFFFF;          // auto reload register
+    TIM->CR1 = TIM_CR1_CEN;     // counter enable
+}
+
+EncoderCounter::~EncoderCounter() {}
+
+/**
+ * Resets the counter value to zero.
+ */
+void EncoderCounter::reset() {
+    
+    TIM->CNT = 0x0000;
+}
+
+/**
+ * Resets the counter value to a given offset value.
+ * @param offset the offset value to reset the counter to.
+ */
+void EncoderCounter::reset(short offset) {
+    
+    TIM->CNT = -offset;
+}
+
+/**
+ * Reads the quadrature encoder counter value.
+ * @return the quadrature encoder counter as a signed 16-bit integer value.
+ */
+short EncoderCounter::read() {
+    
+    return (short)(-TIM->CNT);
+}
+
+/**
+ * The empty operator is a shorthand notation of the <code>read()</code> method.
+ */
+EncoderCounter::operator short() {
+    
+    return read();
+}
+