Diff: release.log

Revision:

9:ff62b20f7000

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/release.log	Mon Apr 04 09:00:31 2016 -0500
@@ -0,0 +1,56 @@
+=mDot Release Log=
+
+==1.0.8==
+
+===Changes===
+* LoRaWAN 1.0 Certified
+* AT+TXP is radio output power, AT+ANT is antenna gain for computing total output power for regulations
+* AT+TXDR can accept values (0-15, DR0-DR15, or SF_7-SF_12) depending on AT+FREQ setting (0-6) -> (DR0-DR6), (7-12) -> (SF_7-SF12)
+*	AT+SLEEP - Enter sleep mode (0:deepsleep,1:sleep)
+*	AT+WP - Wake pin used for sleep mode (1-8) (1:DIN,DIO2-7,DI8) (default: DI8)
+*	AT+JD - join rx window delay 1st window opened at setting 2nd is 1 s after
+*	AT+RXD - rx window delay 1st window opened at setting 2nd is 1 s after
+* 	AT+PS - preserve session over power off and reset in AUTO_OTA mode
+* 	AT+AP - configure app port for uplink data
+*  AT+ANT - configure gain of installed antenna -127 dBi - 128 dBi, (default: 3 dBi)
+* 	AT&K0/3 - Hardware Flow Control (AT&K0: disable, AT&K3: enable)
+* 	AT+REP  - Set number of times to repeat unconfirmed frames (0-15)
+* 	AT+ULC  - Get or set the uplink counter number (sequence number)
+* 	AT+DLC  - Get or set the downlink counter number (sequence number)
+* 	AT+RS  - Restore session info from flash
+* 	AT+SS  - Save session info to flash
+*	AT+TXCH can change channels only for EU868, error for US915
+*	AT&V - Update  output to include new configuration options
+*	help - Move test commands to bottom of help output
+           Add headers for test and debug commands in help output
+* AT+TXP - range changed to 0-20 dBm, antenna gain is applied when setting radio with this power to achieve desired output dBm
+* AT+SDR - get the datarate currently used by the mac layer
+* Removed AT+SENDH - AT+TXDR can accept US(DR0-DR4) and EU(DR0-DR7) to include high-speed datarates US(DR4:SF8BW500) and EU(DR6:SF7BW250,DR7:FSK)
+
+===Bug Fixes===
+* AT+SMODE=1 stays awake until all buffered data is sent
+* Remove 1200 as debug baud rate option
+* AT+SNR - reports SNR values correctly
+* RTC clock not reset over sleep
+* Serial data mode can be entered from command term and escaped with +++
+* Auto OTA mode for EU868 will wait for free channel before trying next join with escape possible
+* Add upto 10 random seconds between join attempts
+
+
+===Known Issues===
+
+==0.1.4==
+===Changes===
+* Features
+
+* Bugfixes
+** Response for US915 - DR4 fixed
+** check the duty-cycles and enable and expired duty cycles before looking for free channel.
+** [1415] +TXN may return very large number
+** added channels to the session to be restored after sleep in AUTO OTA mode.
+** Start uplink counter at 0
+** Sequence number no longer increases by 2 when acks are off
+** [1417] Duty cycle elapsed time was doubled across sleep
+
+
+===Known Issues===