Diff: inc/admw1001/admw1001_config.h

Revision:

5:0728bde67bdb

Child:

6:9d393a9677f4

diff -r 2ca06eee5735 -r 0728bde67bdb inc/admw1001/admw1001_config.h
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/inc/admw1001/admw1001_config.h	Wed Jun 05 05:39:15 2019 +0000
@@ -0,0 +1,980 @@
+/*
+Copyright 2018 (c) Analog Devices, Inc.
+
+All rights reserved.
+
+Redistribution and use in source and binary forms, with or without
+modification, are permitted provided that the following conditions are met:
+  - Redistributions of source code must retain the above copyright
+    notice, this list of conditions and the following disclaimer.
+  - Redistributions in binary form must reproduce the above copyright
+    notice, this list of conditions and the following disclaimer in
+    the documentation and/or other materials provided with the
+    distribution.
+  - Neither the name of Analog Devices, Inc. nor the names of its
+    contributors may be used to endorse or promote products derived
+    from this software without specific prior written permission.
+  - The use of this software may or may not infringe the patent rights
+    of one or more patent holders. This license does not release you
+    from the requirement that you obtain separate licenses from these
+    patent holders to use this software.
+  - Use of the software either in source or binary form, must be run
+    on or directly connected to an Analog Devices Inc. component.
+
+THIS SOFTWARE IS PROVIDED BY ANALOG DEVICES "AS IS" AND ANY EXPRESS OR
+IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, NON-INFRINGEMENT,
+MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
+IN NO EVENT SHALL ANALOG DEVICES BE LIABLE FOR ANY DIRECT, INDIRECT,
+INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+LIMITED TO, INTELLECTUAL PROPERTY RIGHTS, PROCUREMENT OF SUBSTITUTE GOODS OR
+SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/*
+Copyright (c) 2017 Analog Devices, Inc.
+
+All rights reserved.
+
+Redistribution and use in source and binary forms, with or without modification,
+are permitted provided that the following conditions are met:
+  - Redistributions of source code must retain the above copyright notice,
+    this list of conditions and the following disclaimer.
+  - Redistributions in binary form must reproduce the above copyright notice,
+    this list of conditions and the following disclaimer in the documentation
+    and/or other materials provided with the distribution.
+  - Modified versions of the software must be conspicuously marked as such.
+  - This software is licensed solely and exclusively for use with processors
+    manufactured by or for Analog Devices, Inc.
+  - This software may not be combined or merged with other code in any manner
+    that would cause the software to become subject to terms and conditions
+    which differ from those listed here.
+  - Neither the name of Analog Devices, Inc. nor the names of its
+    contributors may be used to endorse or promote products derived
+    from this software without specific prior written permission.
+  - The use of this software may or may not infringe the patent rights of one
+    or more patent holders.  This license does not release you from the
+    requirement that you obtain separate licenses from these patent holders
+    to use this software.
+
+THIS SOFTWARE IS PROVIDED BY ANALOG DEVICES, INC. AND CONTRIBUTORS "AS IS" AND ANY
+EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, NON-INFRINGEMENT,
+TITLE, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+NO EVENT SHALL ANALOG DEVICES, INC. OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
+INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, PUNITIVE OR CONSEQUENTIAL DAMAGES
+(INCLUDING, BUT NOT LIMITED TO, DAMAGES ARISING OUT OF CLAIMS OF INTELLECTUAL
+PROPERTY RIGHTS INFRINGEMENT; PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
+NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
+EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+*/
+
+/*!
+ ******************************************************************************
+ * @file:   admw1001_config.h
+ * @brief:  Configuration type definitions for ADMW1001.
+ *-----------------------------------------------------------------------------
+ */
+
+#ifndef __ADMW1001_CONFIG_H__
+#define __ADMW1001_CONFIG_H__
+
+#include "admw_platform.h"
+#include "admw1001_sensor_types.h"
+
+/* Undefine for versions prior to V2.3. */
+#undef __V2_3_CFG_FMT__
+
+
+/*! @addtogroup ADMW1001_Api
+ *  @{
+ */
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/*! Maximum length allowed for a digital sensor command */
+#define ADMW1001_SENSOR_COMMAND_MAX_LENGTH 7
+
+/*! ADMW1001 channel priority options */
+typedef enum {
+    ADMW1001_CHANNEL_PRIORITY_0 = 0,
+    ADMW1001_CHANNEL_PRIORITY_1,
+    ADMW1001_CHANNEL_PRIORITY_2,
+    ADMW1001_CHANNEL_PRIORITY_3,
+    ADMW1001_CHANNEL_PRIORITY_4,
+    ADMW1001_CHANNEL_PRIORITY_5,
+    ADMW1001_CHANNEL_PRIORITY_6,
+    ADMW1001_CHANNEL_PRIORITY_7,
+    ADMW1001_CHANNEL_PRIORITY_8,
+    ADMW1001_CHANNEL_PRIORITY_9,
+    ADMW1001_CHANNEL_PRIORITY_10,
+    ADMW1001_CHANNEL_PRIORITY_11,
+    ADMW1001_CHANNEL_PRIORITY_12,
+    ADMW1001_CHANNEL_PRIORITY_13,
+    ADMW1001_CHANNEL_PRIORITY_14,
+    ADMW1001_CHANNEL_PRIORITY_15,
+
+    ADMW1001_CHANNEL_PRIORITY_HIGHEST = ADMW1001_CHANNEL_PRIORITY_0,
+    ADMW1001_CHANNEL_PRIORITY_LOWEST  = ADMW1001_CHANNEL_PRIORITY_15,
+} ADMW1001_CHANNEL_PRIORITY;
+
+/*! ADMW1001 operating mode options */
+typedef enum {
+    ADMW1001_OPERATING_MODE_SINGLECYCLE = 0,
+    /*!< Executes a single measurement cycle and stops */
+    ADMW1001_OPERATING_MODE_CONTINUOUS,
+    /*!< Continuously executes measurement cycles */
+    ADMW1001_OPERATING_MODE_MULTICYCLE,
+    /*!< Executes a burst of measurement cycles, repeated at defined intervals */
+} ADMW1001_OPERATING_MODE;
+
+/*! ADMW1001 data ready mode options */
+typedef enum {
+    ADMW1001_DATAREADY_PER_CONVERSION = 0,
+    /*!< The DATAREADY signal is asserted after completion of each conversion
+     *   - a single data sample only from the latest completed conversion is
+     *     stored in this mode
+     */
+    ADMW1001_DATAREADY_PER_CYCLE,
+    /*!< The DATAREADY signal is asserted after completion of each measurement
+     *   cycle
+     *   - data samples only from the lastest completed measurement cycle are
+     *     stored in this mode
+     */
+    ADMW1001_DATAREADY_PER_MULTICYCLE_BURST,
+    /*!< The DATAREADY signal is asserted after completion of each burst of
+     *   measurement cycles
+     *   - applicable only when @ref ADMW1001_OPERATING_MODE_MULTICYCLE
+     *     is also selected
+     *   - data samples only from the lastest completed burst of measurement
+     *     cycles are stored in this mode
+     */
+} ADMW1001_DATAREADY_MODE;
+
+/*! ADMW1001 calibration mode options */
+typedef enum {
+    ADMW1001_NO_CALIBRATION = 0,
+    /*!< No full scale ADC calibration is performed after a latch command is sent.
+     */
+    ADMW1001_DO_CALIBRATION,
+    /*!< Full scale ADC Calibration is performed after a latch command is sent.
+     */
+} ADMW1001_CALIBRATION_MODE;
+
+/*! ADMW1001 power mode options */
+typedef enum {
+    ADMW1001_POWER_MODE_LOW = 1,
+    /*!< Lowest ADC power consumption mode, with lowest conversion rate */
+    ADMW1001_POWER_MODE_MID,
+    /*!< Medium ADC power consumption mode, with medium conversion rate */
+    ADMW1001_POWER_MODE_FULL,
+    /*!< Highest ADC power consumption mode, with highest conversion rate */
+} ADMW1001_POWER_MODE;
+
+/*! ADMW1001 measurement cycle types */
+typedef enum
+{
+    ADMW1001_CYCLE_TYPE_SWITCH = 0,
+    /*!< Switch channels after every conversion */
+    ADMW1001_CYCLE_TYPE_FULL   = 1
+    /*!< Perform full number of requested conversions on a channel
+     *   consecutively before switching to the next channel */
+} ADMW1001_CYCLE_TYPE;
+
+#ifdef __V2_3_CFG_FMT__
+/*! ADMW1001 measurement analog filter settling options */
+typedef enum
+{
+    ADMW1001_FILTER_SETTLING_ALWAYS = 0,
+    /*!< Allow full settling time to elapse between every measurement from an analog sensor */
+    ADMW1001_FILTER_SETTLING_FAST   = 1
+    /*!< Skip settling time between consecutive measurements from an analog sensor */
+} ADMW1001_FILTER_SETTLING;
+#endif
+
+/*! ADMW1001 measurement unit options
+ *
+ *  Optionally select a measurement unit for final conversion results.
+ *  Currently applicable only to specific temperature sensor types.
+ */
+typedef enum {
+    ADMW1001_MEASUREMENT_UNIT_UNSPECIFIED = 0,
+    /*!< No measurement unit specified */
+    ADMW1001_MEASUREMENT_UNIT_CELSIUS,
+    /*!< Celsius temperature unit - applicable to temperature sensors only */
+    ADMW1001_MEASUREMENT_UNIT_FAHRENHEIT,
+    /*!< Fahrenheit temperature unit - applicable to temperature sensors only */
+} ADMW1001_MEASUREMENT_UNIT;
+
+/*! ADMW1001 Open-Sensor Diagnostics frequency
+ *
+ *  Select the per-cycle frequency at which open-sensor diagnostic
+ *  checks should be performed.  Open-sensor diagnostic checks typically require
+ *  specific or time-consuming processing which cannot be executed while a
+ *  measurement cycle is running.
+ *
+ *  @note Open-sensor diagnostic checks, when performed, will add a delay to the
+ *        start of the next measurement cycle.
+ */
+typedef enum {
+    ADMW1001_OPEN_SENSOR_DIAGNOSTICS_DISABLED = 0,
+    /*!< No Open-Sensor Detection is performed */
+    ADMW1001_OPEN_SENSOR_DIAGNOSTICS_PER_CYCLE,
+    /*!< No Open-Sensor Detection is performed prior to each cycle */
+    ADMW1001_OPEN_SENSOR_DIAGNOSTICS_PER_100_CYCLES,
+    /*!< No Open-Sensor Detection is performed at intervals of 100 cycles */
+    ADMW1001_OPEN_SENSOR_DIAGNOSTICS_PER_1000_CYCLES,
+    /*!< No Open-Sensor Detection is performed at intervals of 1000 cycles */
+} ADMW1001_OPEN_SENSOR_DIAGNOSTICS;
+
+/*! ADMW1001 analog input signal amplification gain options
+ *
+ *  @note applicable only to ADC analog sensor channels
+ */
+typedef enum {
+    ADMW1001_ADC_GAIN_1X = 0,
+    /*!< no amplification gain */
+    ADMW1001_ADC_GAIN_2X,
+    /*!< x2 amplification gain */
+    ADMW1001_ADC_GAIN_4X,
+    /*!< x4 amplification gain */
+    ADMW1001_ADC_GAIN_8X,
+    /*!< x8 amplification gain */
+    ADMW1001_ADC_GAIN_16X,
+    /*!< x16 amplification gain */
+    ADMW1001_ADC_GAIN_32X,
+    /*!< x32 amplification gain */
+    ADMW1001_ADC_GAIN_64X,
+    /*!< x64 amplification gain */
+    ADMW1001_ADC_GAIN_128X,
+    /*!< x128 amplification gain */
+} ADMW1001_ADC_GAIN;
+
+/*! ADMW1001 analog sensor excitation current output level options
+ *
+ *  @note applicable only to ADC analog sensor channels, and
+ *        specific sensor types
+ */
+typedef enum {
+    ADMW1001_ADC_EXC_CURRENT_NONE = 0,
+    /*!< Excitation current disabled */
+    ADMW1001_ADC_EXC_CURRENT_50uA,
+    /*!< 50uA excitation current enabled */
+    ADMW1001_ADC_EXC_CURRENT_100uA,
+    /*!< 100uA excitation current  */
+    ADMW1001_ADC_EXC_CURRENT_250uA,
+    /*!< 250uA excitation current enabled */
+    ADMW1001_ADC_EXC_CURRENT_500uA,
+    /*!< 500uA excitation current enabled */
+    ADMW1001_ADC_EXC_CURRENT_750uA,
+    /*!< 750uA excitation current enabled */
+    ADMW1001_ADC_EXC_CURRENT_1000uA,
+    /*!< 1mA excitation current enabled */
+} ADMW1001_ADC_EXC_CURRENT;
+
+/*! ADMW1001 analog sensor excitation current ratios used for diode sensor
+ *
+ *  @note applicable only to a diode sensor
+ */
+typedef enum {
+    ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_DEFAULT = 0,
+    ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_MAX,
+} ADMW1001_ADC_EXC_CURRENT_DIODE_RATIO;
+
+/*! ADMW1001 analog reference selection options
+ *
+ *  @note applicable only to ADC analog sensor channels, and
+ *        specific sensor types
+ */
+typedef enum {
+    ADMW1001_ADC_REFERENCE_NONE = 0,
+    /*!< No reference is selected */
+
+    ADMW1001_ADC_REFERENCE_RESISTOR_INTERNAL_1,
+    /*!< Internal reference resistor #1 (4320 ohms) is selected */
+    ADMW1001_ADC_REFERENCE_RESISTOR_INTERNAL_2,
+    /*!< Internal reference resistor #2 (10000 ohms) is selected */
+    ADMW1001_ADC_REFERENCE_VOLTAGE_INTERNAL,
+    /*!< Internal ADC voltage reference (2.5V) is selected */
+    ADMW1001_ADC_REFERENCE_VOLTAGE_AVDD,
+    /*!< Analag Supply Voltage AVDD reference (typically 3.3V) is selected */
+
+    ADMW1001_ADC_REFERENCE_RESISTOR_EXTERNAL_1,
+    /*!< External user-supplied reference resistor #1 is selected
+     *
+     * @note reference resistor value externalRef1Value must be specified
+     * (see @ref ADMW1001_MEASUREMENT_CONFIG) */
+    ADMW1001_ADC_REFERENCE_RESISTOR_EXTERNAL_2,
+    /*!< External user-supplied reference resistor #2 is selected
+     *
+     * @note reference resistor value externalRef2Value must be specified
+     * (see @ref ADMW1001_MEASUREMENT_CONFIG) */
+    ADMW1001_ADC_REFERENCE_VOLTAGE_EXTERNAL_1,
+    /*!< External user-supplied reference voltage #1 is selected
+     *
+     * @note reference voltage value externalRef1Value must be specified
+     * (see @ref ADMW1001_MEASUREMENT_CONFIG) */
+    ADMW1001_ADC_REFERENCE_VOLTAGE_EXTERNAL_2,
+    /*!< External user-supplied reference voltage #2 is selected
+     *
+     * @note reference voltage value externalRef2Value must be specified
+     * (see @ref ADMW1001_MEASUREMENT_CONFIG) */
+    ADMW1001_ADC_REFERENCE_BRIDGE_EXCITATION,
+    /*!< Bridge Excition Voltage is selected as reference
+     *
+     * @note this reference MUST be selected for 4/6-wire bridge sensor types
+     * (see @ref ADMW1001_ADC_SENSOR_TYPE) */
+} ADMW1001_ADC_REFERENCE_TYPE;
+
+/*! ADMW1001 analog filter selection options
+ *
+ *  @note applicable only to ADC analog sensor channels
+ */
+typedef enum {
+    ADMW1001_ADC_FILTER_SINC4 = 1,
+    /*!< SINC4 filter
+     *
+     * @note The number of input samples to be averaged by the filter
+     *       must be specified by fs (see @ref ADMW1001_ADC_FILTER_CONFIG).
+     *       The fs value affects the output sample rate and settling times
+     *       of the ADC */
+    ADMW1001_ADC_FILTER_FIR_20SPS,
+    /*!< FIR post filter, producing a 20sps output sample rate */
+    ADMW1001_ADC_FILTER_FIR_25SPS,
+    /*!< FIR post filter, producing a 25sps output sample rate */
+} ADMW1001_ADC_FILTER_TYPE;
+
+/*! ADMW1001 FFT sequence mode options
+ *
+ *  @note applicable only for FFT measurement modes
+ */
+typedef enum {
+    ADMW1001_FFT_MODE_SINGLE = 0,
+    /*!< Performs a single sequence of FFTs on selected channels and stops */
+    ADMW1001_FFT_MODE_CONTINUOUS,
+    /*!< Performs continuous sequences of FFTs on selected channels */
+} ADMW1001_FFT_MODE;
+
+/*! ADMW1001 FFT size options (number of bins)
+ *
+ *  @note applicable only for FFT measurement modes
+ */
+typedef enum {
+    ADMW1001_FFT_SIZE_256 = 0,
+    /*!< 256 bins */
+    ADMW1001_FFT_SIZE_512,
+    /*!< 512 bins */
+    ADMW1001_FFT_SIZE_1024,
+    /*!< 1024 bins */
+    ADMW1001_FFT_SIZE_2048,
+    /*!< 2048 bins */
+} ADMW1001_FFT_SIZE;
+
+/*! ADMW1001 FFT window type options
+ *
+ *  @note applicable only for FFT measurement modes
+ */
+typedef enum {
+    ADMW1001_FFT_WINDOW_NONE = 0,
+    /*!< No Window */
+    ADMW1001_FFT_WINDOW_HANN,
+    /*!< Hann Window */
+    ADMW1001_FFT_WINDOW_BLACKMAN_HARRIS,
+    /*!< Blackman-Harris Window */
+} ADMW1001_FFT_WINDOW;
+
+/*! ADMW1001 FFT output format options
+ *
+ *  @note applicable only for FFT measurement modes
+ */
+typedef enum {
+    ADMW1001_FFT_OUTPUT_FULL = 0,
+    /*!< N/2-Term Amplitude Response */
+    ADMW1001_FFT_OUTPUT_FULL_WITH_RAW,
+    /**< N/2-Term Amplitude Response Plus N Raw ADC Samples */
+    ADMW1001_FFT_OUTPUT_MAX16,
+    /*!< Bin-Number and Amplitude of 16 Highest Peaks of Amplitude Response */
+} ADMW1001_FFT_OUTPUT;
+
+/*! ADMW1001 I2C clock speed options
+ *
+ *  @note applicable only for I2C sensors
+ */
+typedef enum
+{
+  ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED_100K = 0,
+    /*!< 100kHz I2C clock speed */
+  ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED_400K,
+    /*!< 400kHz I2C clock speed */
+} ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED;
+
+/*! ADMW1001 UART baud rate options
+ *
+ *  @note applicable only for UART sensors
+ */
+typedef enum
+{
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_BAUD_RATE_115200 = 0,
+    /*!< 115200 UART baud rate */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_BAUD_RATE_57600,
+    /*!< 57600 UART baud rate */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_BAUD_RATE_38400,
+    /*!< 38400 UART baud rate */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_BAUD_RATE_19200,
+    /*!< 19200 UART baud rate */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_BAUD_RATE_9600,
+    /*!< 9600 UART baud rate */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_BAUD_RATE_4800,
+    /*!< 4800 UART baud rate */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_BAUD_RATE_2400,
+    /*!< 2400 UART baud rate */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_BAUD_RATE_1200,
+    /*!< 1200 UART baud rate */
+} ADMW1001_DIGITAL_SENSOR_COMMS_UART_BAUD_RATE;
+
+/*! ADMW1001 UART line config options
+ *
+ *  @note applicable only for UART sensors
+ */
+typedef enum
+{
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_LINE_CONFIG_8N1 = 0,
+    /*!< UART line control 8 data bits / no parity / 1 stop bit  */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_LINE_CONFIG_8N2,
+    /*!< UART line control 8 data bits / no parity / 2 stop bits  */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_LINE_CONFIG_8N3,
+    /*!< UART line control 8 data bits / no parity / 3 stop bits  */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_LINE_CONFIG_8E1,
+    /*!< UART line control 8 data bits / even parity / 1 stop bit  */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_LINE_CONFIG_8E2,
+    /*!< UART line control 8 data bits / even parity / 2 stop bits  */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_LINE_CONFIG_8E3,
+    /*!< UART line control 8 data bits / even parity / 3 stop bits  */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_LINE_CONFIG_8O1,
+    /*!< UART line control 8 data bits / odd parity / 1 stop bit  */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_LINE_CONFIG_8O2,
+    /*!< UART line control 8 data bits / odd parity / 2 stop bits  */
+  ADMW1001_DIGITAL_SENSOR_COMMS_UART_LINE_CONFIG_8O3,
+    /*!< UART line control 8 data bits / odd parity / 3 stop bits  */
+} ADMW1001_DIGITAL_SENSOR_COMMS_UART_LINE_CONFIG;
+
+/*! ADMW1001 SPI mode options
+ *
+ *  @note applicable only for SPI sensors
+ */
+typedef enum
+{
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE_0 = 0,
+    /*!< SPI mode 0 Clock Polarity = 0 Clock Phase = 0 */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE_1,
+    /*!< SPI mode 0 Clock Polarity = 0 Clock Phase = 1 */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE_2,
+    /*!< SPI mode 0 Clock Polarity = 1 Clock Phase = 0 */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE_3,
+    /*!< SPI mode 0 Clock Polarity = 1 Clock Phase = 1 */
+} ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE;
+
+/*! ADMW1001 SPI clock speed options
+ *
+ *  @note applicable only for SPI sensors
+ */
+typedef enum
+{
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_13MHZ = 0,
+    /*!< SPI Clock Speed configured to 13MHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_6_5MHZ,
+    /*!< SPI Clock Speed configured to 6.5MHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_3_25MHZ,
+    /*!< SPI Clock Speed configured to 3.25MHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_1_625MHZ,
+    /*!< SPI Clock Speed configured to 1.625MHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_812KHZ,
+    /*!< SPI Clock Speed configured to 812kHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_406KHZ,
+    /*!< SPI Clock Speed configured to 406kHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_203KHZ,
+    /*!< SPI Clock Speed configured to 203kHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_101KHZ,
+    /*!< SPI Clock Speed configured to 101kHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_50KHZ,
+    /*!< SPI Clock Speed configured to 50kHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_25KHZ,
+    /*!< SPI Clock Speed configured to 25kHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_12KHZ,
+    /*!< SPI Clock Speed configured to 12kHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_6KHZ,
+    /*!< SPI Clock Speed configured to 6kHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_3KHZ,
+    /*!< SPI Clock Speed configured to 3kHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_1_5KHZ,
+    /*!< SPI Clock Speed configured to 1.5kHz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_793HZ,
+    /*!< SPI Clock Speed configured to 793hz */
+  ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_396HZ,
+    /*!< SPI Clock Speed configured to 396hz */
+} ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK;
+
+/*! ADMW1001 Power Configuration options */
+typedef struct {
+    ADMW1001_POWER_MODE        powerMode;
+    /*!< Power mode selection */
+} ADMW1001_POWER_CONFIG;
+
+/*! ADMW1001 Multi-Cycle Configuration options
+ *
+ * @note required only when ADMW1001_OPERATING_MODE_MULTICYCLE is selected
+ *       as the operatingMode (@ref ADMW1001_MEASUREMENT_CONFIG)
+ */
+typedef struct {
+    uint32_t                         cyclesPerBurst;
+    /*!< Number of cycles to complete for a single burst */
+    uint32_t                         burstInterval;
+    /*!< Interval, in seconds, between each successive burst of cycles */
+} ADMW1001_MULTICYCLE_CONFIG;
+
+/*! ADMW1001 Measurement Configuration options */
+typedef struct {
+    ADMW1001_OPERATING_MODE    operatingMode;
+    /*!< Operating mode - specifies how measurement cycles are scheduled */
+    ADMW1001_DATAREADY_MODE    dataReadyMode;
+    /*!< Data read mode - specifies how output samples are stored for reading */
+    ADMW1001_CALIBRATION_MODE calibrationMode;
+    /*!< Calibration mode - specifies if adc calibration is performed after a latch command */
+    ADMW1001_MULTICYCLE_CONFIG multiCycleConfig;
+    /*!< Multi-Cycle configuration - specifies how bursts of measurement cycles
+     *   are scheduled.  Applicable only when operatingMode is
+     *   ADMW1001_OPERATING_MODE_MULTICYCLE
+     */
+    uint32_t                         cycleInterval;
+    /*!< Cycle interval - specifies the time interval between the start of each
+     *   successive measurement cycle.  Applicable only when operatingMode is
+     *   not ADMW1001_OPERATING_MODE_SINGLECYCLE
+     */
+    ADMW1001_CYCLE_TYPE        cycleType;
+    /*!< Cycle type - specifies how the channel list is traversed with each
+     *   conversion during the cycle.
+     */
+#ifdef __V2_3_CFG_FMT__
+    ADMW1001_FILTER_SETTLING   filterSettling;
+    /*!< Analog filter settling - specifies the policy for settling time
+     *   between consecutive measurements from an analog channel in a multi-
+     *   channel configuration.  Note that, in single analog channel
+     *   configurations, settling time is always skipped between consecutive
+     *   measurements in a measurement cycle.
+     */
+#endif
+    float32_t                        externalRef1Value;
+    /*!< Resistance/voltage value connected to external reference input #1.
+     *   Applicable only if the selected reference type is
+     *   ADMW1001_ADC_REFERENCE_RESISTOR_EXTERNAL_1 or
+     *   ADMW1001_ADC_REFERENCE_VOLTAGE_EXTERNAL_1
+     *   (see @ref ADMW1001_ADC_REFERENCE_TYPE)
+     */
+    float32_t                        externalRef2Value;
+    /*!< Resistance/voltage value connected to external reference input #2.
+     *   Applicable only if the selected reference type is
+     *   ADMW1001_ADC_REFERENCE_RESISTOR_EXTERNAL_2 or
+     *   ADMW1001_ADC_REFERENCE_VOLTAGE_EXTERNAL_2
+     *   (see @ref ADMW1001_ADC_REFERENCE_TYPE)
+     */    
+    bool                             enableExternalFlash;
+    /*!< Enable the use of external flash memory for storage of samples.
+     */
+} ADMW1001_MEASUREMENT_CONFIG;
+
+/*! ADMW1001 ADC Excitation Current output configuration
+ *
+ *  @note applicable only to ADC analog sensor channels, and
+ *        specific sensor types
+ */
+typedef struct {
+    ADMW1001_ADC_EXC_CURRENT              outputLevel;
+    /*!< Excitation current output level */
+    ADMW1001_ADC_EXC_CURRENT_DIODE_RATIO  diodeRatio;
+    /*!< Excitation current output diode ratio */
+} ADMW1001_ADC_EXC_CURRENT_CONFIG;
+
+/*! ADMW1001 ADC Filter configuration
+ *
+ *  @note applicable only to ADC analog sensor channels
+ */
+typedef struct {
+    ADMW1001_ADC_FILTER_TYPE   type;
+    /*!< Filter type selection */
+    uint32_t                         fs;
+    /*!< Number of input samples to accumulate and average in the filter.
+     *   Applicable only when type is ADMW1001_ADC_FILTER_SINC4 */
+} ADMW1001_ADC_FILTER_CONFIG;
+
+/*! ADMW1001 ADC Referemce configuration
+ *
+ *  @note applicable only to ADC analog sensor channels
+ */
+typedef struct {
+    ADMW1001_ADC_REFERENCE_TYPE type;
+    /*!< Filter type selection */
+    bool                              disableBuffer;
+    /*!< Option to disable internal ADC reference buffer */
+} ADMW1001_ADC_REFERENCE_CONFIG;
+
+/*! ADMW1001 ADC analog channel configuration details
+ *
+ *  @note applicable only to ADC analog sensor channels
+ */
+typedef struct {
+    ADMW1001_ADC_SENSOR_TYPE        sensor;
+    /*!< Sensor type selection */
+    ADMW1001_ADC_GAIN               gain;
+    /*!< ADC Gain selection */
+    ADMW1001_ADC_EXC_CURRENT_CONFIG current;
+    /*!< ADC Excitation Current configuration */
+    ADMW1001_ADC_FILTER_CONFIG      filter;
+    /*!< ADC Filter configuration */
+    ADMW1001_ADC_REFERENCE_CONFIG   reference;
+    /*!< ADC Reference configuration */
+    bool                                  enableVbias;
+    /*!< Option to enable internal ADC voltage bias */
+} ADMW1001_ADC_CHANNEL_CONFIG;
+
+/*! ADMW1001 digital sensor data encoding
+ *
+ *  @note applicable only to SPI and I2C digital sensor channels
+ */
+typedef enum
+{
+    ADMW1001_DIGITAL_SENSOR_DATA_CODING_NONE,
+    /**< None/Invalid - data format is ignored if coding is set to this value */
+    ADMW1001_DIGITAL_SENSOR_DATA_CODING_UNIPOLAR,
+    /**< Unipolar - unsigned integer values */
+    ADMW1001_DIGITAL_SENSOR_DATA_CODING_TWOS_COMPLEMENT,
+    /**< Twos-complement - signed integer values */
+    ADMW1001_DIGITAL_SENSOR_DATA_CODING_OFFSET_BINARY,
+    /**< Offset Binary - used to represent signed values with unsigned integers,
+     *   with the mid-range value representing 0 */
+} ADMW1001_DIGITAL_SENSOR_DATA_CODING;
+
+/*! ADMW1001 digital sensor data format configuration
+ *
+ *  @note applicable only to SPI and I2C digital sensor channels
+ */
+typedef struct {
+    ADMW1001_DIGITAL_SENSOR_DATA_CODING coding;
+    /**< Data Encoding of Sensor Result */
+    bool littleEndian;
+    /**< Set as true if data format is little-endian, false otherwise */
+    bool leftJustified;
+    /**< Set as true if data is left-justified in the data frame, false otherwise */
+    uint8_t frameLength;
+    /**< Data frame length (number of bytes to read from the sensor) */
+    uint8_t numDataBits;
+    /**< Number of relevant data bits to extract from the data frame */
+    uint8_t bitOffset;
+    /**< Data bit offset, relative to data alignment within the data frame */
+} ADMW1001_DIGITAL_SENSOR_DATA_FORMAT;
+
+/*! ADMW1001 digital sensor command
+ *
+ *  @note applicable only to SPI and I2C digital sensor channels
+ */
+typedef struct {
+    uint8_t command[ADMW1001_SENSOR_COMMAND_MAX_LENGTH];
+    /*!< Optional command bytes to send to the device */
+    uint8_t commandLength;
+    /*!< Number of valid command bytes.  Set to 0 if unused */
+} ADMW1001_DIGITAL_SENSOR_COMMAND;
+
+/*! ADMW1001 digital sensor calibration param
+ *
+ *  @note applicable only to digital sensor channels
+ */
+typedef struct {
+    uint32_t calibrationParam;
+    /*!< Independently established environmental variable used during calibration
+     *   of a digital sensor. Used only if the sensor supports calibration
+     *   and expects an environmental parameter
+     */
+    bool enableCalibrationParam;
+    /*!< Allow Calibration_Parameter to be used during calibration of any digital sensor */
+} ADMW1001_DIGITAL_CALIBRATION_COMMAND;
+
+/*! ADMW1001 digital sensor communication config
+ *
+ *  @note applicable only to digital sensor channels
+ */
+typedef struct {
+    bool  useCustomCommsConfig;
+    /*!< Optional parameter to enable user digital communication settings */
+    ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED     i2cClockSpeed;
+    /*!< Optional parameter to configure specific i2c speed for i2c sensor */
+    ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE            spiMode;
+    /*!< Optional parameter to configure specific spi mode for spi sensor */
+    ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK           spiClock;
+    /*!< Optional parameter to configure specific spi clock for spi sensor */
+    ADMW1001_DIGITAL_SENSOR_COMMS_UART_BAUD_RATE      uartBaudRate;
+    /*!< Optional parameter to configure specific uart baud rate for uart sensor */
+    ADMW1001_DIGITAL_SENSOR_COMMS_UART_LINE_CONFIG    uartLineConfig;
+    /*!< Optional parameter to configure specific uart line control for uart sensor */
+} ADMW1001_DIGITAL_SENSOR_COMMS;
+
+/*! ADMW1001 I2C digital channel configuration details
+ *
+ *  @note applicable only to I2C digital sensor channels
+ */
+typedef struct {
+    ADMW1001_I2C_SENSOR_TYPE        sensor;
+    /*!< Sensor type selection */
+    uint32_t                              deviceAddress;
+    /*!< I2C device address (7-bit) */
+    ADMW1001_DIGITAL_SENSOR_COMMAND configurationCommand;
+    /*!< Optional configuration command to send to the device at start-up.
+     *   A default configuration command will be used if this is not specified.
+     *   Applicable only to specific I2C sensor types.
+     */
+    ADMW1001_DIGITAL_SENSOR_COMMAND dataRequestCommand;
+    /*!< Optional data request command to send to the device for each sample.
+     *   A default data request command will be used if this is not specified.
+     *   Applicable only to specific I2C sensor types.
+     */
+    ADMW1001_DIGITAL_SENSOR_DATA_FORMAT dataFormat;
+    /*!< Optional data format configuration to parse/extract data from the device.
+     *   A default data format will be used if this is not specified.
+     *   Applicable only to specific I2C sensor types
+     */
+    ADMW1001_DIGITAL_CALIBRATION_COMMAND digitalCalibrationParam;
+    /*!< This is used to supply an independently established environmental variable
+     *   that must be used during calibration of a [digital] sensor which a)
+     *   supports calibration and b) expects an environmental parameter.
+     *   An example is a CO2 sensor, which may require the CO2 concentration level
+     *   when performing a calibration
+     */
+    ADMW1001_DIGITAL_SENSOR_COMMS configureComms;
+    /*!< Optional configuration to setup a user communication config.
+     *   A default configuration  will be used if this is not specified.
+     *   Applicable only to specific I2C sensor types.
+     */
+} ADMW1001_I2C_CHANNEL_CONFIG;
+
+/*! ADMW1001 SPI digital channel configuration details
+ *
+ *  @note applicable only to SPI digital sensor channels
+ */
+typedef struct {
+    ADMW1001_SPI_SENSOR_TYPE        sensor;
+    /*!< Sensor type selection */
+    ADMW1001_DIGITAL_SENSOR_COMMAND configurationCommand;
+    /*!< Optional configuration command to send to the device at start-up.
+     *   A default configuration command will be used if this is not specified.
+     *   Applicable only to specific SPI sensor types.
+     */
+    ADMW1001_DIGITAL_SENSOR_COMMAND dataRequestCommand;
+    /*!< Optional data request command to send to the device for each sample.
+     *   A default data request command will be used if this is not specified.
+     *   Applicable only to specific SPI sensor types.
+     */
+    ADMW1001_DIGITAL_SENSOR_DATA_FORMAT dataFormat;
+    /*!< Optional data format configuration to parse/extract data from the device.
+     *   A default data format will be used if this is not specified.
+     *   Applicable only to specific SPI sensor types
+     */
+    ADMW1001_DIGITAL_CALIBRATION_COMMAND digitalCalibrationParam;
+    /*!< This is used to supply an independently established environmental variable
+     *   that must be used during calibration of a [digital] sensor which a)
+     *   supports calibration and b) expects an environmental parameter.
+     *   An example is a CO2 sensor, which may require the CO2 concentration level
+     *   when performing a calibration
+     */
+    ADMW1001_DIGITAL_SENSOR_COMMS configureComms;
+    /*!< Optional configuration to setup a user communication config.
+     *   A default configuration  will be used if this is not specified.
+     *   Applicable only to specific SPI sensor types.
+     */
+} ADMW1001_SPI_CHANNEL_CONFIG;
+
+/*! ADMW1001 UART digital channel configuration details
+ *
+ *  @note applicable only to UART digital sensor channels
+ */
+typedef struct {
+    ADMW1001_UART_SENSOR_TYPE        sensor;
+    /*!< Sensor type selection */
+    ADMW1001_DIGITAL_CALIBRATION_COMMAND digitalCalibrationParam;
+    /*!< This is used to supply an independently established environmental variable
+     *   that must be used during calibration of a [digital] sensor which a)
+     *   supports calibration and b) expects an environmental parameter.
+     *   An example is a CO2 sensor, which may require the CO2 concentration level
+     *   when performing a calibration
+     */
+    ADMW1001_DIGITAL_SENSOR_COMMS configureComms;
+    /*!< Optional configuration to setup a user communication config.
+     *   A default configuration  will be used if this is not specified.
+     *   Applicable only to specific UART sensor types.
+     */
+} ADMW1001_UART_CHANNEL_CONFIG;
+
+/*! ADMW1001 Measurement Channel configuration details */
+typedef struct {
+    bool                                 enableChannel;
+    /*!< Option to include this channel in normal measurement cycles */
+    bool                                 enableFFT;
+    /*!< Option to include this channel in FFT measurement cycles */
+    bool                                 disablePublishing;
+    /*!< Option to disable publishing of data samples from this channel.  The
+     *   channel may still be included in measurement cycles, but data samples
+     *   obtained from this channel will not be published.  This is typically
+     *   used for channels which are required only as a compensation reference
+     *   for another channel (e.g. Cold-Junction Compensation channels).
+     */
+    ADMW1001_CHANNEL_ID            compensationChannel;
+    /*!< Optional compensation channel.  Set to ADMW1001_CHANNEL_ID_NONE if not
+     *   required.  Typically used for thermocouple sensors that require a
+     *   separate measurement of the "cold-junction" temperature, which can be
+     *   be provided by an RTD temperature sensor connected on a separate
+     *   "compensation channel" */
+    bool                                 enableUnityLut;
+    /*!< Option to choose the LUT for calculations, this implies that the
+     * fundamental measurement for the sensor (typically mV or Ohms)
+     * would be returned as the measurement result.
+     */
+    ADMW1001_MEASUREMENT_UNIT      measurementUnit;
+    /*!< Optional measurement unit selection for conversion results.  Applicable
+     *   only for certain sensor types.  Set to
+     *   ADMW1001_MEASUREMENT_UNIT_DEFAULT if not applicable.
+     */
+    float32_t                            lowThreshold;
+    /*!< Optional minimum threshold value for each processed sample, to be
+     *   checked prior to publishing.  A channel ALERT condition is raised
+     *   if the processed value is lower than this threshold.  Set to NaN
+     *   if not required.
+     */
+    float32_t                            highThreshold;
+    /*!< Optional maximum threshold value for each processed sample, to be
+     *   checked prior to publishing.  A channel ALERT condition is raised
+     *   if the processed value is higher than this threshold.  Set to NaN
+     *   if not required.
+     */
+    float32_t                            offsetAdjustment;
+    /*!< Optional offset adjustment value applied to each processed sample.
+     *   Set to NaN or 0.0 if not required.
+     */
+    float32_t                            gainAdjustment;
+    /*!< Optional gain adjustment value applied to each processed sample.
+     *   Set to NaN or 1.0 if not required.
+     */
+    float32_t                            sensorParameter;
+    /*!< Optional sensor parameter adjustment.
+     *   Set to NaN or 0 if not required.
+     */
+    uint32_t                             measurementsPerCycle;
+    /*!< The number of measurements to obtain from this channel within each
+     *   cycle.  Each enabled channel is measured in turn, until the number of
+     *   measurements requested for the channel has been reached.  A different
+     *   number of measurements-per-cycle may be specified for each channel.
+     */
+    uint32_t                             cycleSkipCount;
+    /*!< Optional number of cycles to skip, such that this channel is included
+     *   in the sequence in only one of every (cycleSkipCount + 1) cycles that
+     *   occur.  If set to 0 (default), this channel is included in every cycle;
+     *   if set to 1, this channel is included in every 2nd cycle; if set to 2,
+     *   this channel is included in every 3rd cycle, and so on.
+     */
+    uint32_t                             extraSettlingTime;
+    /*!< A minimum settling time is applied internally for each channel, based
+     *   on the sensor type.  However, additional settling time (microseconds)
+     *   can optionally be specified.  Set to 0 if not required.
+     */
+    ADMW1001_CHANNEL_PRIORITY      priority;
+    /*!< By default, channels are arranged in the measurement sequence based on
+     *   ascending order of channel ID.  However, a priority-level may be
+     *   specified per channel to force a different ordering of the channels,
+     *   with higher-priority channels appearing before lower-priority channels.
+     *   Channels with equal priority are ordered by ascending order of channel
+     *   ID.  Lower numbers indicate higher priority, with 0 being the highest.
+     *   Set to 0 if not required.
+     */
+    union {
+        ADMW1001_ADC_CHANNEL_CONFIG adcChannelConfig;
+        /*!< ADC channel configuration - applicable only to ADC channels */
+        ADMW1001_I2C_CHANNEL_CONFIG i2cChannelConfig;
+        /*!< I2C channel configuration - applicable only to I2C channels */
+        ADMW1001_SPI_CHANNEL_CONFIG spiChannelConfig;
+        /*!< SPI channel configuration - applicable only to SPI channels */
+        ADMW1001_UART_CHANNEL_CONFIG uartChannelConfig;
+        /*!< UART channel configuration - applicable only to UART channels */
+    };
+    /*!< Only one of adcChannelConfig, i2cChannelConfig, spiChannelConfig or
+     *   uartChannelConfig is required, depending on the channel designation
+     *   (analog, I2C, SPI or UART)
+     */
+} ADMW1001_CHANNEL_CONFIG;
+
+/*! ADMW1001 Diagnostics configuration details */
+typedef struct {
+    bool                                   disableGlobalDiag;
+    /*!< Option to disable the following diagnostic checks on the ADC:
+     *   - Reference Detection errors
+     *   - Input under-/over-voltage errors
+     *   - Calibration, Conversion and Saturation errors
+     */
+    bool                                   disableMeasurementDiag;
+    /*!< Option to disable additional checks per measurement channel:
+     *   - High/low threshold limit violation
+     */
+#ifdef __V2_3_CFG_FMT__
+    bool                                   disableCriticalTempAbort;
+    /*!< Option to disable abort of measurement cycle if the operating
+     *   temperature of the ADMW1001 has exceeded critical limits
+     */
+#endif
+    ADMW1001_OPEN_SENSOR_DIAGNOSTICS osdFrequency;
+    /*!< Option to enable Open-Circuit Detection at a selected cycle interval */
+} ADMW1001_DIAGNOSTICS_CONFIG;
+
+/*! ADMW1001 FFT Measurement Mode configuration options */
+typedef struct {
+    ADMW1001_FFT_MODE               mode;
+    /*!< FFT sequence mode */
+    ADMW1001_FFT_SIZE               size;
+    /*!< FFT size selection */
+    ADMW1001_FFT_WINDOW             window;
+    /*!< FFT window type selection */
+    ADMW1001_FFT_OUTPUT             output;
+    /*!< FFT output type selection */
+} ADMW1001_FFT_CONFIG;
+
+#ifdef __V2_3_CFG_FMT__
+typedef uint16_t ADMW1001_ADVANCED_ACCESS_KEY;
+#endif
+
+/*! ADMW1001 Device configuration details */
+typedef struct {
+    ADMW1001_POWER_CONFIG           power;
+    /*!< Power configuration details */
+    ADMW1001_MEASUREMENT_CONFIG     measurement;
+    /*!< Measurement configuration details */
+    ADMW1001_DIAGNOSTICS_CONFIG     diagnostics;
+    /*!< Diagnostics configuration details */
+    ADMW1001_FFT_CONFIG             fft;
+    /*!< FFT configuration details */
+    ADMW1001_CHANNEL_CONFIG         channels[ADMW1001_MAX_CHANNELS];
+    /*!< Channel-specific configuration details */
+#ifdef __V2_3_CFG_FMT__
+    ADMW1001_ADVANCED_ACCESS_KEY    advancedAccessKey;
+#endif
+    /*!< Key to enable access to advanced sensor configuration options */
+} ADMW1001_CONFIG;
+
+#ifdef __cplusplus
+}
+#endif
+
+/*!
+ * @}
+ */
+
+#endif /* __ADMW1001_CONFIG_H__ */
+