Vybhav Kadaba
Minor changes to support ADMW FWv1.17.75
Diff: inc/admw1001/admw1001_config.h
- Revision:
- 34:b60ee1e0af2b
- Parent:
- 33:df7a00f1b8e1
- Child:
- 43:e1789b7214cf
--- a/inc/admw1001/admw1001_config.h Thu Nov 14 05:35:08 2019 +0000
+++ b/inc/admw1001/admw1001_config.h Tue Nov 19 11:17:35 2019 +0000
@@ -58,8 +58,7 @@
#define ADMW1001_SENSOR_COMMAND_MAX_LENGTH 7
/*! ADMW1001 channel priority options */
-typedef enum
-{
+typedef enum {
ADMW1001_CHANNEL_PRIORITY_0 = 0,
ADMW1001_CHANNEL_PRIORITY_1,
ADMW1001_CHANNEL_PRIORITY_2,
@@ -80,8 +79,7 @@
} ADMW1001_CHANNEL_PRIORITY;
/*! ADMW1001 operating mode options */
-typedef enum
-{
+typedef enum {
ADMW1001_OPERATING_MODE_SINGLECYCLE = 0,
/*!< Executes a single measurement cycle and stops */
ADMW1001_OPERATING_MODE_CONTINUOUS,
@@ -92,8 +90,7 @@
} ADMW1001_OPERATING_MODE;
/*! ADMW1001 data ready mode options */
-typedef enum
-{
+typedef enum {
ADMW1001_DATAREADY_PER_CONVERSION = 0,
/*!< The DATAREADY signal is asserted after completion of each conversion
* - a single data sample only from the latest completed conversion is
@@ -114,8 +111,7 @@
} ADMW1001_DATAREADY_MODE;
/*! ADMW1001 power mode options */
-typedef enum
-{
+typedef enum {
ADMW1001_POWER_MODE_HIBERNATION = 0,
/*!< module has entede hibernation mode. All analog circuitry is disabled. All peripherals disabled apart from the Wake-up pin functionality. */
ADMW1001_POWER_MODE_ACTIVE,
@@ -124,8 +120,7 @@
} ADMW1001_POWER_MODE;
/*! ADMW1001 measurement analog filter settling options */
-typedef enum
-{
+typedef enum {
ADMW1001_FILTER_SETTLING_ALWAYS = 0,
/*!< Allow full settling time to elapse between every measurement from an analog sensor */
ADMW1001_FILTER_SETTLING_FAST,
@@ -138,8 +133,7 @@
* Optionally select a measurement unit for final conversion results.
* Currently applicable only to specific temperature sensor types.
*/
-typedef enum
-{
+typedef enum {
ADMW1001_MEASUREMENT_UNIT_UNSPECIFIED = 0,
/*!< No measurement unit specified */
ADMW1001_MEASUREMENT_UNIT_CELSIUS,
@@ -159,8 +153,7 @@
* @note Open-sensor diagnostic checks, when performed, will add a delay to the
* start of the next measurement cycle.
*/
-typedef enum
-{
+typedef enum {
ADMW1001_OPEN_SENSOR_DIAGNOSTICS_DISABLED = 0,
/*!< No Open-Sensor Detection is performed */
ADMW1001_OPEN_SENSOR_DIAGNOSTICS_PER_CYCLE,
@@ -173,21 +166,19 @@
} ADMW1001_OPEN_SENSOR_DIAGNOSTICS;
-typedef enum
-{
+typedef enum {
ADMW1001_BUFFER_BYPASSS_DISABLED = 0,
/*!< Buffer Bypass Disabled */
ADMW1001_BUFFER_BYPASSS_ENABLED,
/*!< Buffer Bypass Enabled */
-
+
} ADMW1001_BUFFER_BYPASSS;
/*! ADMW1001 analog input signal amplification gain options
*
* @note applicable only to ADC analog sensor channels
*/
-typedef enum
-{
+typedef enum {
ADMW1001_ADC_RTD_CURVE_EUROPEAN = 0,
/*!< EUROPEAN RTD curve used. */
ADMW1001_ADC_RTD_CURVE_AMERICAN,
@@ -202,8 +193,7 @@
*
* @note applicable only to ADC analog sensor channels
*/
-typedef enum
-{
+typedef enum {
ADMW1001_ADC_GAIN_1X = 0,
/*!< no amplification gain */
ADMW1001_ADC_GAIN_2X,
@@ -228,8 +218,7 @@
* @note applicable only to ADC analog sensor channels, and
* specific sensor types
*/
-typedef enum
-{
+typedef enum {
ADMW1001_ADC_EXC_STATE_CYCLE_POWER=0,
/*!< Excitation for measurement is active only during measurement */
ADMW1001_ADC_EXC_STATE_ALWAYS_ON,
@@ -241,12 +230,11 @@
* @note applicable only to ADC analog sensor channels, and
* specific sensor types
*/
-typedef enum
-{
+typedef enum {
ADMW1001_ADC_NO_EXTERNAL_EXC_CURRENT = -1,
- /*!< NO External excitation is provided */
+ /*!< NO External excitation is provided */
ADMW1001_ADC_EXC_CURRENT_EXTERNAL = 0,
- /*!< External excitation is provided */
+ /*!< External excitation is provided */
ADMW1001_ADC_EXC_CURRENT_50uA,
/*!< 50uA excitation current enabled */
ADMW1001_ADC_EXC_CURRENT_100uA,
@@ -264,21 +252,20 @@
*
* @note applicable only to a diode sensor
*/
-typedef enum
-{
- ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_10UA_100UA = 0,
+typedef enum {
+ ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_10UA_100UA = 0,
/**< 2 Current measurement 10uA 100uA */
- ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_20UA_160UA,
+ ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_20UA_160UA,
/**< 2 Current measurement 20uA 160uA */
- ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_50UA_300UA,
+ ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_50UA_300UA,
/**< 2 Current measurement 50uA 300uA */
- ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_100UA_600UA,
+ ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_100UA_600UA,
/**< 2 Current measurement 100uA 600uA */
- ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_10UA_50UA_100UA,
+ ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_10UA_50UA_100UA,
/**< 3 current measuremetn 10uA 50uA 100uA */
- ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_20UA_100UA_160UA,
+ ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_20UA_100UA_160UA,
/**< 3 current measuremetn 20uA 100uA 160uA */
- ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_50UA_150UA_300UA,
+ ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_50UA_150UA_300UA,
/**< 3 current measuremetn 50uA 150uA 300uA */
ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_100UA_300UA_600UA,
/**< 3 current measuremetn 100uA 300uA 600uA */
@@ -290,8 +277,7 @@
* @note applicable only to ADC analog sensor channels, and
* specific sensor types
*/
-typedef enum
-{
+typedef enum {
ADMW1001_ADC_REFERENCE_VOLTAGE_INTERNAL = 0,
/*!< Internal VRef - 1.2V */
ADMW1001_ADC_REFERENCE_VOLTAGE_EXTERNAL_1,
@@ -307,8 +293,7 @@
*
* @note applicable only to ADC analog sensor channels
*/
-typedef enum
-{
+typedef enum {
ADMW1001_ADC_GND_SW_OPEN = 0,
/*!< Ground switch not enabled for measurement. */
ADMW1001_ADC_GND_SW_CLOSED,
@@ -320,8 +305,7 @@
*
* @note applicable only to ADC analog sensor channels
*/
-typedef enum
-{
+typedef enum {
ADMW1001_CHOP_MD_NONE = 0,
/*!< No chop performed. */
ADMW1001_CHOP_MD_HW,
@@ -330,15 +314,14 @@
/*!< Software only chop performed. */
ADMW1001_CHOP_MD_HWSW,
/*!< Hardware and software chop performed. */
-
+
} ADMW1001_CHOP_MD;
/*! ADMW1001 analog filter selection options
*
* @note applicable only to ADC analog sensor channels
*/
-typedef enum
-{
+typedef enum {
ADMW1001_ADC_FILTER_SINC4 = 0,
/*!< SINC4 - 4th order sinc response filter */
ADMW1001_ADC_FILTER_SINC3,
@@ -349,11 +332,10 @@
/*! ADMW1001 Sinc Filter range (SF)
*
* @note applicable only to ADC analog sensor channels
- * @note SF must be set in conjunction with chop mode
+ * @note SF must be set in conjunction with chop mode
* and sinc filter type to achieve the desired sampling rate.
*/
-typedef enum
-{
+typedef enum {
ADMW1001_SF_976HZ = 0,
/*!< SF setting for 976Hz sample rate. */
ADMW1001_SF_488HZ = 1,
@@ -379,8 +361,7 @@
*
* @note applicable only for I2C sensors
*/
-typedef enum
-{
+typedef enum {
ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED_100K = 0,
/*!< 100kHz I2C clock speed */
ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED_400K,
@@ -392,8 +373,7 @@
*
* @note applicable only for SPI sensors
*/
-typedef enum
-{
+typedef enum {
ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE_0 = 0,
/*!< SPI mode 0 Clock Polarity = 0 Clock Phase = 0 */
ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE_1,
@@ -409,8 +389,7 @@
*
* @note applicable only for SPI sensors
*/
-typedef enum
-{
+typedef enum {
ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_8MHZ = 0,
/*!< SPI Clock Speed configured to 8MHz */
ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_4MHZ,
@@ -447,8 +426,7 @@
} ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK;
/*! ADMW1001 Power Configuration options */
-typedef struct
-{
+typedef struct {
ADMW1001_POWER_MODE powerMode;
/*!< Power mode selection */
@@ -459,8 +437,7 @@
* @note required only when ADMW1001_OPERATING_MODE_MULTICYCLE is selected
* as the operatingMode (@ref ADMW1001_MEASUREMENT_CONFIG)
*/
-typedef struct
-{
+typedef struct {
uint32_t cyclesPerBurst;
/*!< Number of cycles to complete for a single burst */
uint32_t burstInterval;
@@ -469,8 +446,7 @@
} ADMW1001_MULTICYCLE_CONFIG;
/*! ADMW1001 Measurement Configuration options */
-typedef struct
-{
+typedef struct {
ADMW1001_OPERATING_MODE operatingMode;
/*!< Operating mode - specifies how measurement cycles are scheduled */
ADMW1001_DATAREADY_MODE dataReadyMode;
@@ -489,7 +465,7 @@
*/
uint8_t reserved0[3];
/*!< Reserved for future use and ensure word alignment.
- */
+ */
uint32_t cycleInterval;
/*!< Cycle interval - specifies the time interval between the start of each
* successive measurement cycle. Applicable only when operatingMode is
@@ -503,12 +479,13 @@
* Applicable only if the selected reference type is
* voltage.
* (see @ref ADMW1001_ADC_REFERENCE_TYPE)
- */
+ */
float32_t RSenseValue;
- /*!< Sense resistor value in Ohms. */
- uint32_t reserved1[3];
- /*!< Reserved for future use and ensure word alignment.
- */
+ /*!< Sense resistor value in Ohms. */
+ float32_t externalRefVoltage;
+ /*!< External Reference Voltage.
+ */
+ uint32_t reserved1[2];
} ADMW1001_MEASUREMENT_CONFIG;
@@ -517,8 +494,7 @@
* @note applicable only to ADC analog sensor channels, and
* specific sensor types
*/
-typedef struct
-{
+typedef struct {
ADMW1001_ADC_EXC_STATE excitationState;
/*!< Excitation current state */
ADMW1001_ADC_EXC_CURRENT outputLevel;
@@ -532,8 +508,7 @@
*
* @note applicable only to ADC analog sensor channels
*/
-typedef struct
-{
+typedef struct {
ADMW1001_ADC_FILTER_TYPE type;
/*!< Filter type selection */
ADMW1001_SINC_FILTER_RANGE sf;
@@ -551,8 +526,7 @@
*
* @note applicable only to ADC analog sensor channels
*/
-typedef struct
-{
+typedef struct {
ADMW1001_ADC_SENSOR_TYPE sensor;
/*!< Sensor type selection */
ADMW1001_ADC_RTD_CURVE rtdCurve;
@@ -567,7 +541,7 @@
bool vBiasEnable;
/*!< ADC Reference configuration */
uint8_t bufferBypass;
- /*!< Buffer Bypass configuration */
+ /*!< Buffer Bypass configuration */
uint8_t reserved0[2];
/*!< Reserved for future use and ensure word alignment. */
uint32_t reserved1[6];
@@ -578,8 +552,7 @@
/*! ADMW1001 look-up table selection
* Select table used to linearise the measurement.
*/
-typedef enum
-{
+typedef enum {
ADMW1001_LUT_DEFAULT = 0,
/*!< Default LUT */
ADMW1001_LUT_UNITY = 1,
@@ -588,15 +561,14 @@
/*!< User defined custom LUT */
ADMW1001_LUT_RESERVED = 3,
/*!< Reserved for future use */
-
+
} ADMW1001_LUT_SELECT;
/*! ADMW1001 digital sensor data encoding
*
* @note applicable only to SPI and I2C digital sensor channels
*/
-typedef enum
-{
+typedef enum {
ADMW1001_DIGITAL_SENSOR_DATA_CODING_NONE = 0,
/**< None/Invalid - data format is ignored if coding is set to this value */
ADMW1001_DIGITAL_SENSOR_DATA_CODING_UNIPOLAR,
@@ -613,8 +585,7 @@
*
* @note applicable only to SPI and I2C digital sensor channels
*/
-typedef struct
-{
+typedef struct {
ADMW1001_DIGITAL_SENSOR_DATA_CODING coding;
/**< Data Encoding of Sensor Result */
bool littleEndian;
@@ -636,8 +607,7 @@
*
* @note applicable only to SPI and I2C digital sensor channels
*/
-typedef struct
-{
+typedef struct {
uint8_t command[ADMW1001_SENSOR_COMMAND_MAX_LENGTH];
/*!< Optional command bytes to send to the device */
uint8_t commandLength;
@@ -649,8 +619,7 @@
*
* @note applicable only to digital sensor channels
*/
-typedef struct
-{
+typedef struct {
uint32_t calibrationParam;
/*!< Independently established environmental variable used during calibration
* of a digital sensor. Used only if the sensor supports calibration
@@ -667,8 +636,7 @@
*
* @note applicable only to digital sensor channels
*/
-typedef struct
-{
+typedef struct {
bool useCustomCommsConfig;
/*!< Optional parameter to enable user digital communication settings */
ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED i2cClockSpeed;
@@ -684,8 +652,7 @@
*
* @note applicable only to I2C digital sensor channels
*/
-typedef struct
-{
+typedef struct {
ADMW1001_I2C_SENSOR_TYPE sensor;
/*!< Sensor type selection */
uint8_t deviceAddress;
@@ -726,12 +693,11 @@
*
* @note applicable only to SPI digital sensor channels
*/
-typedef struct
-{
+typedef struct {
ADMW1001_SPI_SENSOR_TYPE sensor;
/*!< Sensor type selection */
uint8_t reserved[2];
- /*!< Reserved for future use and ensure word alignment. */
+ /*!< Reserved for future use and ensure word alignment. */
ADMW1001_DIGITAL_SENSOR_COMMAND configurationCommand;
/*!< Optional configuration command to send to the device at start-up.
* A default configuration command will be used if this is not specified.
@@ -763,8 +729,7 @@
} ADMW1001_SPI_CHANNEL_CONFIG;
/*! ADMW1001 Measurement Channel configuration details */
-typedef struct
-{
+typedef struct {
bool enableChannel;
/*!< Option to include this channel in normal measurement cycles */
bool disablePublishing;
@@ -841,8 +806,7 @@
* ID. Lower numbers indicate higher priority, with 0 being the highest.
* Set to 0 if not required.
*/
- union
- {
+ union {
ADMW1001_ADC_CHANNEL_CONFIG adcChannelConfig;
/*!< ADC channel configuration - applicable only to ADC channels */
ADMW1001_I2C_CHANNEL_CONFIG i2cChannelConfig;
@@ -858,8 +822,7 @@
} ADMW1001_CHANNEL_CONFIG;
/*! ADMW1001 Diagnostics configuration details */
-typedef struct
-{
+typedef struct {
bool disableGlobalDiag;
/*!< Option to disable the following diagnostic checks on the ADC:
* - Reference Detection errors
@@ -884,8 +847,7 @@
typedef uint16_t ADMW1001_ADVANCED_ACCESS_KEY;
/*! ADMW1001 Device configuration details */
-typedef struct
-{
+typedef struct {
ADMW1001_POWER_CONFIG power;
/*!< Power configuration details */
ADMW1001_MEASUREMENT_CONFIG measurement;