Vybhav Kadaba
Bumped Mbed FW version to 01.20.0080
Diff: inc/admw1001/admw1001_config.h
- Revision:
- 45:f5f553b8c0d5
- Parent:
- 43:e1789b7214cf
- Child:
- 50:d84305e5e1c0
--- a/inc/admw1001/admw1001_config.h Thu Jan 16 06:52:27 2020 +0000
+++ b/inc/admw1001/admw1001_config.h Mon Jan 20 10:40:06 2020 +0000
@@ -58,7 +58,8 @@
#define ADMW1001_SENSOR_COMMAND_MAX_LENGTH 7
/*! ADMW1001 channel priority options */
-typedef enum {
+typedef enum
+{
ADMW1001_CHANNEL_PRIORITY_0 = 0,
ADMW1001_CHANNEL_PRIORITY_1,
ADMW1001_CHANNEL_PRIORITY_2,
@@ -79,7 +80,8 @@
} ADMW1001_CHANNEL_PRIORITY;
/*! ADMW1001 operating mode options */
-typedef enum {
+typedef enum
+{
ADMW1001_OPERATING_MODE_SINGLECYCLE = 0,
/*!< Executes a single measurement cycle and stops */
ADMW1001_OPERATING_MODE_CONTINUOUS,
@@ -90,7 +92,8 @@
} ADMW1001_OPERATING_MODE;
/*! ADMW1001 data ready mode options */
-typedef enum {
+typedef enum
+{
ADMW1001_DATAREADY_PER_CONVERSION = 0,
/*!< The DATAREADY signal is asserted after completion of each conversion
* - a single data sample only from the latest completed conversion is
@@ -111,7 +114,8 @@
} ADMW1001_DATAREADY_MODE;
/*! ADMW1001 power mode options */
-typedef enum {
+typedef enum
+{
ADMW1001_POWER_MODE_HIBERNATION = 0,
/*!< module has entede hibernation mode. All analog circuitry is disabled. All peripherals disabled apart from the Wake-up pin functionality. */
ADMW1001_POWER_MODE_ACTIVE,
@@ -120,7 +124,8 @@
} ADMW1001_POWER_MODE;
/*! ADMW1001 measurement analog filter settling options */
-typedef enum {
+typedef enum
+{
ADMW1001_FILTER_SETTLING_ALWAYS = 0,
/*!< Allow full settling time to elapse between every measurement from an analog sensor */
ADMW1001_FILTER_SETTLING_FAST,
@@ -133,7 +138,8 @@
* Optionally select a measurement unit for final conversion results.
* Currently applicable only to specific temperature sensor types.
*/
-typedef enum {
+typedef enum
+{
ADMW1001_MEASUREMENT_UNIT_UNSPECIFIED = 0,
/*!< No measurement unit specified */
ADMW1001_MEASUREMENT_UNIT_CELSIUS,
@@ -143,30 +149,8 @@
} ADMW1001_MEASUREMENT_UNIT;
-/*! ADMW1001 Open-Sensor Diagnostics frequency
- *
- * Select the per-cycle frequency at which open-sensor diagnostic
- * checks should be performed. Open-sensor diagnostic checks typically require
- * specific or time-consuming processing which cannot be executed while a
- * measurement cycle is running.
- *
- * @note Open-sensor diagnostic checks, when performed, will add a delay to the
- * start of the next measurement cycle.
- */
-typedef enum {
- ADMW1001_OPEN_SENSOR_DIAGNOSTICS_DISABLED = 0,
- /*!< No Open-Sensor Detection is performed */
- ADMW1001_OPEN_SENSOR_DIAGNOSTICS_PER_CYCLE,
- /*!< No Open-Sensor Detection is performed prior to each cycle */
- ADMW1001_OPEN_SENSOR_DIAGNOSTICS_PER_100_CYCLES,
- /*!< No Open-Sensor Detection is performed at intervals of 100 cycles */
- ADMW1001_OPEN_SENSOR_DIAGNOSTICS_PER_1000_CYCLES,
- /*!< No Open-Sensor Detection is performed at intervals of 1001 cycles */
-
-} ADMW1001_OPEN_SENSOR_DIAGNOSTICS;
-
-
-typedef enum {
+typedef enum
+{
ADMW1001_BUFFER_BYPASSS_DISABLED = 0,
/*!< Buffer Bypass Disabled */
ADMW1001_BUFFER_BYPASSS_ENABLED,
@@ -178,7 +162,8 @@
*
* @note applicable only to ADC analog sensor channels
*/
-typedef enum {
+typedef enum
+{
ADMW1001_ADC_RTD_CURVE_EUROPEAN = 0,
/*!< EUROPEAN RTD curve used. */
ADMW1001_ADC_RTD_CURVE_AMERICAN,
@@ -193,7 +178,8 @@
*
* @note applicable only to ADC analog sensor channels
*/
-typedef enum {
+typedef enum
+{
ADMW1001_ADC_GAIN_1X = 0,
/*!< no amplification gain */
ADMW1001_ADC_GAIN_2X,
@@ -218,11 +204,13 @@
* @note applicable only to ADC analog sensor channels, and
* specific sensor types
*/
-typedef enum {
- ADMW1001_ADC_EXC_STATE_CYCLE_POWER=0,
+typedef enum
+{
+ ADMW1001_ADC_EXC_STATE_CYCLE_POWER = 0,
/*!< Excitation for measurement is active only during measurement */
ADMW1001_ADC_EXC_STATE_ALWAYS_ON,
/*!< Excitation for measurement is always on */
+
} ADMW1001_ADC_EXC_STATE;
/*! ADMW1001 analog sensor excitation current output level options
@@ -230,7 +218,8 @@
* @note applicable only to ADC analog sensor channels, and
* specific sensor types
*/
-typedef enum {
+typedef enum
+{
ADMW1001_ADC_NO_EXTERNAL_EXC_CURRENT = -1,
/*!< NO External excitation is provided */
ADMW1001_ADC_EXC_CURRENT_EXTERNAL = 0,
@@ -252,7 +241,8 @@
*
* @note applicable only to a diode sensor
*/
-typedef enum {
+typedef enum
+{
ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_10UA_100UA = 0,
/**< 2 Current measurement 10uA 100uA */
ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_20UA_160UA,
@@ -277,7 +267,8 @@
* @note applicable only to ADC analog sensor channels, and
* specific sensor types
*/
-typedef enum {
+typedef enum
+{
ADMW1001_ADC_REFERENCE_VOLTAGE_INTERNAL = 0,
/*!< Internal VRef - 1.2V */
ADMW1001_ADC_REFERENCE_VOLTAGE_EXTERNAL_1,
@@ -293,7 +284,8 @@
*
* @note applicable only to ADC analog sensor channels
*/
-typedef enum {
+typedef enum
+{
ADMW1001_ADC_GND_SW_OPEN = 0,
/*!< Ground switch not enabled for measurement. */
ADMW1001_ADC_GND_SW_CLOSED,
@@ -305,7 +297,8 @@
*
* @note applicable only to ADC analog sensor channels
*/
-typedef enum {
+typedef enum
+{
ADMW1001_CHOP_MD_NONE = 0,
/*!< No chop performed. */
ADMW1001_CHOP_MD_HW,
@@ -321,7 +314,8 @@
*
* @note applicable only to ADC analog sensor channels
*/
-typedef enum {
+typedef enum
+{
ADMW1001_ADC_FILTER_SINC4 = 0,
/*!< SINC4 - 4th order sinc response filter */
ADMW1001_ADC_FILTER_SINC3,
@@ -335,7 +329,8 @@
* @note SF must be set in conjunction with chop mode
* and sinc filter type to achieve the desired sampling rate.
*/
-typedef enum {
+typedef enum
+{
ADMW1001_SF_976HZ = 0,
/*!< SF setting for 976Hz sample rate. */
ADMW1001_SF_488HZ = 1,
@@ -361,7 +356,8 @@
*
* @note applicable only for I2C sensors
*/
-typedef enum {
+typedef enum
+{
ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED_100K = 0,
/*!< 100kHz I2C clock speed */
ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED_400K,
@@ -373,7 +369,8 @@
*
* @note applicable only for SPI sensors
*/
-typedef enum {
+typedef enum
+{
ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE_0 = 0,
/*!< SPI mode 0 Clock Polarity = 0 Clock Phase = 0 */
ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE_1,
@@ -389,7 +386,8 @@
*
* @note applicable only for SPI sensors
*/
-typedef enum {
+typedef enum
+{
ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_8MHZ = 0,
/*!< SPI Clock Speed configured to 8MHz */
ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_4MHZ,
@@ -426,7 +424,8 @@
} ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK;
/*! ADMW1001 Power Configuration options */
-typedef struct {
+typedef struct
+{
ADMW1001_POWER_MODE powerMode;
/*!< Power mode selection */
@@ -437,7 +436,8 @@
* @note required only when ADMW1001_OPERATING_MODE_MULTICYCLE is selected
* as the operatingMode (@ref ADMW1001_MEASUREMENT_CONFIG)
*/
-typedef struct {
+typedef struct
+{
uint32_t cyclesPerBurst;
/*!< Number of cycles to complete for a single burst */
uint32_t burstInterval;
@@ -446,7 +446,8 @@
} ADMW1001_MULTICYCLE_CONFIG;
/*! ADMW1001 Measurement Configuration options */
-typedef struct {
+typedef struct
+{
ADMW1001_OPERATING_MODE operatingMode;
/*!< Operating mode - specifies how measurement cycles are scheduled */
ADMW1001_DATAREADY_MODE dataReadyMode;
@@ -463,10 +464,10 @@
* configurations, settling time is always skipped between consecutive
* measurements in a measurement cycle.
*/
- ADMW1001_ADC_EXC_STATE excitationState;
+ uint8_t excitationState;
/*!< Excitation current state */
- ADMW1001_ADC_GND_SW groundSwitch;
- /*!< Option to open or close sensor ground switch */
+ uint8_t groundSwitch;
+ /*!< Option to open or close sensor ground switch */
uint8_t reserved0;
/*!< Reserved for future use and ensure word alignment.
*/
@@ -489,7 +490,12 @@
float32_t externalRefVoltage;
/*!< External Reference Voltage.
*/
- uint32_t reserved1[2];
+ float32_t AVDDVoltage;
+ /*!< AVDD Voltage.
+ */
+ uint32_t reserved1[1];
+ /*!< Reserved for future use and ensure word alignment.
+ */
} ADMW1001_MEASUREMENT_CONFIG;
@@ -498,11 +504,13 @@
* @note applicable only to ADC analog sensor channels, and
* specific sensor types
*/
-typedef struct {
+typedef struct
+{
ADMW1001_ADC_EXC_CURRENT outputLevel;
/*!< Excitation current output level */
ADMW1001_ADC_EXC_CURRENT_DIODE_RATIO diodeRatio;
/*!< Excitation current output diode ratio */
+ float32_t idealityRatio;
} ADMW1001_ADC_EXC_CURRENT_CONFIG;
@@ -510,7 +518,8 @@
*
* @note applicable only to ADC analog sensor channels
*/
-typedef struct {
+typedef struct
+{
ADMW1001_ADC_FILTER_TYPE type;
/*!< Filter type selection */
ADMW1001_SINC_FILTER_RANGE sf;
@@ -519,13 +528,15 @@
/*!< Enable filter chop */
bool notch1p2;
/*!< Enable Notch 2 Filter Mode */
+
} ADMW1001_ADC_FILTER_CONFIG;
/*! ADMW1001 ADC analog channel configuration details
*
* @note applicable only to ADC analog sensor channels
*/
-typedef struct {
+typedef struct
+{
ADMW1001_ADC_SENSOR_TYPE sensor;
/*!< Sensor type selection */
ADMW1001_ADC_RTD_CURVE rtdCurve;
@@ -537,10 +548,9 @@
ADMW1001_ADC_FILTER_CONFIG filter;
/*!< ADC Filter configuration */
ADMW1001_ADC_REFERENCE_TYPE reference;
- bool vBiasEnable;
/*!< ADC Reference configuration */
uint8_t bufferBypass;
- /*!< Buffer Bypass configuration */
+ /*!< Buffer Bypass configuration */
uint8_t reserved0[2];
/*!< Reserved for future use and ensure word alignment. */
uint32_t reserved1[6];
@@ -551,14 +561,13 @@
/*! ADMW1001 look-up table selection
* Select table used to linearise the measurement.
*/
-typedef enum {
+typedef enum
+{
ADMW1001_LUT_DEFAULT = 0,
/*!< Default LUT */
- ADMW1001_LUT_UNITY = 1,
- /*!< Unity LUT */
- ADMW1001_LUT_CUSTOM = 2,
+ ADMW1001_LUT_CUSTOM = 1,
/*!< User defined custom LUT */
- ADMW1001_LUT_RESERVED = 3,
+ ADMW1001_LUT_RESERVED = 2,
/*!< Reserved for future use */
} ADMW1001_LUT_SELECT;
@@ -567,7 +576,8 @@
*
* @note applicable only to SPI and I2C digital sensor channels
*/
-typedef enum {
+typedef enum
+{
ADMW1001_DIGITAL_SENSOR_DATA_CODING_NONE = 0,
/**< None/Invalid - data format is ignored if coding is set to this value */
ADMW1001_DIGITAL_SENSOR_DATA_CODING_UNIPOLAR,
@@ -584,7 +594,8 @@
*
* @note applicable only to SPI and I2C digital sensor channels
*/
-typedef struct {
+typedef struct
+{
ADMW1001_DIGITAL_SENSOR_DATA_CODING coding;
/**< Data Encoding of Sensor Result */
bool littleEndian;
@@ -606,7 +617,8 @@
*
* @note applicable only to SPI and I2C digital sensor channels
*/
-typedef struct {
+typedef struct
+{
uint8_t command[ADMW1001_SENSOR_COMMAND_MAX_LENGTH];
/*!< Optional command bytes to send to the device */
uint8_t commandLength;
@@ -618,7 +630,8 @@
*
* @note applicable only to digital sensor channels
*/
-typedef struct {
+typedef struct
+{
uint32_t calibrationParam;
/*!< Independently established environmental variable used during calibration
* of a digital sensor. Used only if the sensor supports calibration
@@ -635,7 +648,8 @@
*
* @note applicable only to digital sensor channels
*/
-typedef struct {
+typedef struct
+{
bool useCustomCommsConfig;
/*!< Optional parameter to enable user digital communication settings */
ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED i2cClockSpeed;
@@ -651,7 +665,8 @@
*
* @note applicable only to I2C digital sensor channels
*/
-typedef struct {
+typedef struct
+{
ADMW1001_I2C_SENSOR_TYPE sensor;
/*!< Sensor type selection */
uint8_t deviceAddress;
@@ -692,7 +707,8 @@
*
* @note applicable only to SPI digital sensor channels
*/
-typedef struct {
+typedef struct
+{
ADMW1001_SPI_SENSOR_TYPE sensor;
/*!< Sensor type selection */
uint8_t reserved[2];
@@ -728,7 +744,8 @@
} ADMW1001_SPI_CHANNEL_CONFIG;
/*! ADMW1001 Measurement Channel configuration details */
-typedef struct {
+typedef struct
+{
bool enableChannel;
/*!< Option to include this channel in normal measurement cycles */
bool disablePublishing;
@@ -793,7 +810,7 @@
*/
uint32_t extraSettlingTime;
/*!< A minimum settling time is applied internally for each channel, based
- * on the sensor type. However, additional settling time (microseconds)
+ * on the sensor type. However, additional settling time (milliseconds)
* can optionally be specified. Set to 0 if not required.
*/
ADMW1001_CHANNEL_PRIORITY priority;
@@ -805,7 +822,8 @@
* ID. Lower numbers indicate higher priority, with 0 being the highest.
* Set to 0 if not required.
*/
- union {
+ union
+ {
ADMW1001_ADC_CHANNEL_CONFIG adcChannelConfig;
/*!< ADC channel configuration - applicable only to ADC channels */
ADMW1001_I2C_CHANNEL_CONFIG i2cChannelConfig;
@@ -821,7 +839,8 @@
} ADMW1001_CHANNEL_CONFIG;
/*! ADMW1001 Diagnostics configuration details */
-typedef struct {
+typedef struct
+{
bool disableGlobalDiag;
/*!< Option to disable the following diagnostic checks on the ADC:
* - Reference Detection errors
@@ -838,7 +857,7 @@
* temperature of the ADMW1001 has exceeded critical limits
*/
- ADMW1001_OPEN_SENSOR_DIAGNOSTICS osdFrequency;
+ uint8_t osdFrequency;
/*!< Option to enable Open-Circuit Detection at a selected cycle interval */
} ADMW1001_DIAGNOSTICS_CONFIG;
@@ -846,7 +865,8 @@
typedef uint16_t ADMW1001_ADVANCED_ACCESS_KEY;
/*! ADMW1001 Device configuration details */
-typedef struct {
+typedef struct
+{
ADMW1001_POWER_CONFIG power;
/*!< Power configuration details */
ADMW1001_MEASUREMENT_CONFIG measurement;