Diff: ssd1306.h

Revision:

2:e479b0296757

Parent:

1:1d58d378221c

Child:

3:1d9df877c90a

diff -r 1d58d378221c -r e479b0296757 ssd1306.h
--- a/ssd1306.h	Tue Feb 05 17:18:23 2013 +0000
+++ b/ssd1306.h	Tue Feb 05 21:21:22 2013 +0000
@@ -8,7 +8,7 @@
 
 /** SSD1306 Controller Driver
  *
- * Information taken from the datasheet at: 
+ * Information taken from the datasheet at:
  *   http://www.adafruit.com/datasheets/SSD1306.pdf
  */
 class SSD1306
@@ -20,46 +20,174 @@
      *  @param dc The connected DC pin.
      *  @param clk The connected CLK pin.
      *  @param data The connected Data pin.
+     */
     SSD1306(PinName cs, PinName rs, PinName dc, PinName clk, PinName data);
 
+    // ----- HARDWARE CONTROL -----
+
+    /** Initialise the display with defaults.*/
     void initialise();
+    
+    /** Force a refresh of the display.  Copies the buffer to the controller. */
     void update();
 
+    /** Turn the whole display off.  This will reset all configuration settings on the controller to their defaults. */
     void off();
+    
+    /** Turn the whole display on.  Used during initialisation. */
     void on();
+
+    /** Sends the display to sleep, but leaves RAM intact. */
+    void sleep();
+
+    /** Wakes up this display following a sleep() call.
+     *  @see sleep()
+     */
+    void wake();
+
+    /** Set the display contrast.
+     *  @param value The contrast, from 1 to 256.
+     */
+    void set_contrast(unsigned char value); // 1-256
+    
+    /** Set the display to normal or inverse.
+     *  @param value 0 for normal mode, or 1 for inverse mode.
+     */
+    void set_inverse(unsigned char value); // 0 or 1
     
-    // Sends the display to sleep, but leaves RAM intact
-    void sleep();
+    /** Set the display start line.  This is the line at which the display will start rendering.
+     *  @param value A value from 0 to 63 denoting the line to start at.
+     */
+    void set_display_start_line(unsigned char value); // 0-63
+    
+    /** Set the segment remap state.  This allows the module to be addressed as if flipped horizontally.
+      * NOTE: Changing this setting has no effect on data already in the module's GDDRAM.
+      * @param value 0 = column address 0 = segment 0 (the default), 1 = column address 127 = segment 0 (flipped).
+      */
+    void set_segment_remap(unsigned char value); // 0 or 1
+    
+    /** Set the vertical shift by COM.
+      * @param value The number of rows to shift, from 0 - 63.
+      */
+    void set_display_offset(unsigned char value); // 0-63
+    
+    /** Set the multiplex ratio.
+     *  @param value MUX will be set to (value+1). Valid values range from 15 to 63 - MUX 16 to 64.
+     */
+    void set_multiplex_ratio(unsigned char value); // 15-63 (value+1 mux)
+    
+    /** Set COM output scan direction.  If the display is active, this will immediately vertically
+      * flip the display.
+      * @param value 0 = Scan from COM0 (default), 1 = reversed (scan from COM[N-1]).
+      */
+    void set_com_output_scan_direction(unsigned char value); // 0 or 1
     
-    // 
-    void wake();
-   
-    void set_low_column(int value);
-    void set_high_column(int value);
-    void set_start_line(int value);    
+    /** Set COM pins hardware configuration.
+      * @param sequential 0 = Sequental COM pin configuration, 1 = Alternative COM pin configuration (default).
+      * @param lr_remap 0 = Disable COM left/right remap (default), 1 = enable COM left/right remap.
+      */
+    void set_com_pins_hardware_configuration(unsigned char sequential, unsigned char lr_remap); // 0 or 1 for both parametrs
+
+    /** Set up and start a continuous horizontal scroll.
+      * Once you have set up the scrolling, you can deactivate it with stop_scroll().
+      * @param direction 0 for right, 1 for left.
+      * @param start Start page address, 0 - 5.
+      * @param end End page address, 0 - 5.
+      * @param interval Interval in frame frequency.  Valid values are: 2, 3, 4, 5, 25, 64, 128, 256.
+      * @see stop_scrol
+      */
+    void start_horizontal_scroll(unsigned char direction, unsigned char start, unsigned char end, unsigned char interval);
+
+    /** Set up and start a continuous horizontal and vertical scroll.
+      * NOTE: No continuous vertical scroll is available.
+      * Once you have set up the scrolling, you can deactivate it with stop_scroll().
+      * @param direction 0 for vertical and right horizontal scroll, 1 for vertical and left horizontal scroll.
+      * @param start Start page address, 0 - 5.
+      * @param end End page address, 0 - 5.
+      * @param interval Interval in frame frequency.  Valid values are: 2, 3, 4, 5, 25, 64, 128, 256.
+      * @param vertical_offset Offset of vertical scroll, 1 - 63.
+      * @see stop_scroll
+      */
+    void start_vertical_and_horizontal_scroll(unsigned char direction, unsigned char start, unsigned char end, unsigned char interval, unsigned char vertical_offset);
+    
+    /** Deactivate the continuous scroll set up with start_horizontal_scroll() or 
+      * start_vertical_and_horizontal_scroll().
+      * @see set_horizontal_scroll, set_vertical_and_horizontal_scroll
+      */
+    void stop_scroll();
+    
+    // ----- ADDRESSING -----
+    
+    /** Set memory addressing mode to the given value.
+      * @param mode 0 for Horizontal addressing mode, 1 for Vertical addressing mode, or 2 for Page addressing mode (PAM).  2 is the default.
+      */
+    void set_memory_addressing_mode(unsigned char mode);
+    
+    /** Page Addressing Mode: Set the column start address register for
+      * page addressing mode.
+      * @param address The address (full byte).
+      */
+    void pam_set_start_address(unsigned char address);       
+    
+    /** Set the GDDRAM page start address for page addressing mode.
+      * @param address The start page, 0 - 7.
+      */
+    void pam_set_page_start(unsigned char address);
+    
+    /** Set page start and end address for horizontal/vertical addressing mode.
+      * @param start The start page, 0 - 7.
+      * @param end The end page, 0 - 7.
+      */
+    void hv_set_page_address(unsigned char start, unsigned char end);
+    
+    /** Set column address range for horizontal/vertical addressing mode.
+      * @param start Column start address, 0 - 127.
+      * @param end Column end address, 0 - 127.
+      */
+    void hv_set_column_address(unsigned char start, unsigned char end);
+    
+    // ----- TIMING & DRIVING -----
+    /** Set the display clock divide ratio and the oscillator frequency.
+      * @param ratio The divide ratio, default is 0.
+      * @param frequency The oscillator frequency, 0 - 127. Default is 8.  
+      */
+    void set_display_clock_ratio_and_frequency(unsigned char ratio, unsigned char frequency);
+    
+    /** Set the precharge period.
+      * @param phase1 Phase 1 period in DCLK clocks.  1 - 15, default is 2.
+      * @param phase2 Phase 2 period in DCLK clocks.  1 - 15, default is 2.
+      */
+    void set_precharge_period(unsigned char phase1, unsigned char phase2);
+    
+    /** Set the Vcomh deselect level.
+      * @param level 0 = 0.65 x Vcc, 1 = 0.77 x Vcc (default), 2 = 0.83 x Vcc.
+      */
+    void set_vcomh_deselect_level(unsigned char level);
+    
+    /** Perform a "no operation".
+      */
+    void nop();
+    
+    /** Enable/disable charge pump.
+      @param enable 0 to disable, 1 to enable the internal charge pump.
+      */
+    void set_charge_pump_enable(unsigned char enable);
+    
+    // ----- BUFFER EDITING -----
 
     void clear();
     void set_pixel(int x, int y);
     void clear_pixel(int x, int y);
     void line(int x0, int y0, int x1, int y1);
-    
+
     void draw_string(char *font, int x, int y, const char *string);
     void draw_char(char *font, int x, int y, char c);
-    
-    void set_contrast(unsigned char value); // 1-256
-    void set_inverse(unsigned char value); // 0 or 1
-    void set_display_start_line(unsigned char value); // 0-63
-    void set_horizontal_flip(unsigned char value); // 0 or 1
-    void set_display_offset(unsigned char value); // 0-63
-    void set_multiplex_ratio(unsigned char value); // 15-63 (value+1 mux)
-    void set_com_output_scan_direction(unsigned char value); // 0 or 1
-    void set_com_pins_hardware_configuration(unsigned char sequential, unsigned char lr_remap); // 0 or 1 for both parametrs
 
 private:
     SPI _spi;
     DigitalOut _cs, _reset, _dc;
-    char _screen[1024];
-
+    unsigned char _screen[1024];
+    
     int _cursor_x, _cursor_y;
 
     void _send_command(unsigned char code);
@@ -69,39 +197,4 @@
 #define SSD1306_LCDWIDTH 128
 #define SSD1306_LCDHEIGHT 64
 
-#define SSD1306_SETCONTRAST 0x81
-#define SSD1306_DISPLAYALLON_RESUME 0xA4
-#define SSD1306_DISPLAYALLON 0xA5
-#define SSD1306_NORMALDISPLAY 0xA6
-#define SSD1306_INVERTDISPLAY 0xA7
-#define SSD1306_DISPLAYOFF 0xAE
-#define SSD1306_DISPLAYON 0xAF
-
-#define SSD1306_SETDISPLAYOFFSET 0xD3
-#define SSD1306_SETCOMPINS 0xDA
-
-#define SSD1306_SETVCOMDETECT 0xDB
-
-#define SSD1306_SETDISPLAYCLOCKDIV 0xD5
-#define SSD1306_SETPRECHARGE 0xD9
-
-#define SSD1306_SETMULTIPLEX 0xA8
-
-#define SSD1306_SETLOWCOLUMN 0x00
-#define SSD1306_SETHIGHCOLUMN 0x10
-
-#define SSD1306_SETSTARTLINE 0x40
-
-#define SSD1306_MEMORYMODE 0x20
-
-#define SSD1306_COMSCANINC 0xC0
-#define SSD1306_COMSCANDEC 0xC8
-
-#define SSD1306_SEGREMAP 0xA0
-
-#define SSD1306_CHARGEPUMP 0x8D
-
-#define SSD1306_EXTERNALVCC 0x1
-#define SSD1306_SWITCHCAPVCC 0x2
-
 #endif