TIM_Private_Functions
[TIM]

Configure the TI1 as Input.

Parameters:

TIMx,:	where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
TIM_ICPolarity	: The Input Polarity. This parameter can be one of the following values: TIM_ICPolarity_Rising TIM_ICPolarity_Falling
TIM_ICSelection,:	specifies the input to be used. This parameter can be one of the following values: TIM_ICSelection_DirectTI: TIM Input 1 is selected to be connected to IC1. TIM_ICSelection_IndirectTI: TIM Input 1 is selected to be connected to IC2. TIM_ICSelection_TRC: TIM Input 1 is selected to be connected to TRC.
TIM_ICFilter,:	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 2701 of file stm32f10x_tim.c.

Configure the TI2 as Input.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
TIM_ICPolarity	: The Input Polarity. This parameter can be one of the following values: TIM_ICPolarity_Rising TIM_ICPolarity_Falling
TIM_ICSelection,:	specifies the input to be used. This parameter can be one of the following values: TIM_ICSelection_DirectTI: TIM Input 2 is selected to be connected to IC2. TIM_ICSelection_IndirectTI: TIM Input 2 is selected to be connected to IC1. TIM_ICSelection_TRC: TIM Input 2 is selected to be connected to TRC.
TIM_ICFilter,:	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 2748 of file stm32f10x_tim.c.

Configure the TI3 as Input.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_ICPolarity	: The Input Polarity. This parameter can be one of the following values: TIM_ICPolarity_Rising TIM_ICPolarity_Falling
TIM_ICSelection,:	specifies the input to be used. This parameter can be one of the following values: TIM_ICSelection_DirectTI: TIM Input 3 is selected to be connected to IC3. TIM_ICSelection_IndirectTI: TIM Input 3 is selected to be connected to IC4. TIM_ICSelection_TRC: TIM Input 3 is selected to be connected to TRC.
TIM_ICFilter,:	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 2797 of file stm32f10x_tim.c.

Configure the TI4 as Input.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_ICPolarity	: The Input Polarity. This parameter can be one of the following values: TIM_ICPolarity_Rising TIM_ICPolarity_Falling
TIM_ICSelection,:	specifies the input to be used. This parameter can be one of the following values: TIM_ICSelection_DirectTI: TIM Input 4 is selected to be connected to IC4. TIM_ICSelection_IndirectTI: TIM Input 4 is selected to be connected to IC3. TIM_ICSelection_TRC: TIM Input 4 is selected to be connected to TRC.
TIM_ICFilter,:	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 2845 of file stm32f10x_tim.c.

Enables or disables TIMx peripheral Preload register on ARR.

Parameters:

TIMx,:	where x can be 1 to 17 to select the TIM peripheral.
NewState,:	new state of the TIMx peripheral Preload register This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 1409 of file stm32f10x_tim.c.

Configures the: Break feature, dead time, Lock level, the OSSI, the OSSR State and the AOE(automatic output enable).

Parameters:

TIMx,:	where x can be 1 or 8 to select the TIM
TIM_BDTRInitStruct,:	pointer to a TIM_BDTRInitTypeDef structure that contains the BDTR Register configuration information for the TIM peripheral.

Return values:

None

Definition at line 712 of file stm32f10x_tim.c.

Fills each TIM_BDTRInitStruct member with its default value.

Parameters:

TIM_BDTRInitStruct,:

pointer to a TIM_BDTRInitTypeDef structure which will be initialized.

Return values:

None

Definition at line 787 of file stm32f10x_tim.c.

Sets or Resets the TIM peripheral Capture Compare Preload Control bit.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8 or 15 to select the TIMx peripheral
NewState,:	new state of the Capture Compare Preload Control bit This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 1483 of file stm32f10x_tim.c.

Enables or disables the TIM Capture Compare Channel x.

Parameters:

TIMx,:	where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
TIM_Channel,:	specifies the TIM Channel This parameter can be one of the following values: TIM_Channel_1: TIM Channel 1 TIM_Channel_2: TIM Channel 2 TIM_Channel_3: TIM Channel 3 TIM_Channel_4: TIM Channel 4
TIM_CCx,:	specifies the TIM Channel CCxE bit new state. This parameter can be: TIM_CCx_Enable or TIM_CCx_Disable.

Return values:

None

Definition at line 1974 of file stm32f10x_tim.c.

Enables or disables the TIM Capture Compare Channel xN.

Parameters:

TIMx,:	where x can be 1, 8, 15, 16 or 17 to select the TIM peripheral.
TIM_Channel,:	specifies the TIM Channel This parameter can be one of the following values: TIM_Channel_1: TIM Channel 1 TIM_Channel_2: TIM Channel 2 TIM_Channel_3: TIM Channel 3
TIM_CCxN,:	specifies the TIM Channel CCxNE bit new state. This parameter can be: TIM_CCxN_Enable or TIM_CCxN_Disable.

Return values:

None

Definition at line 2004 of file stm32f10x_tim.c.

Clears the TIMx's pending flags.

Parameters:

TIMx,:

where x can be 1 to 17 to select the TIM peripheral.

TIM_FLAG,:

specifies the flag bit to clear. This parameter can be any combination of the following values: TIM_FLAG_Update: TIM update Flag TIM_FLAG_CC1: TIM Capture Compare 1 Flag TIM_FLAG_CC2: TIM Capture Compare 2 Flag TIM_FLAG_CC3: TIM Capture Compare 3 Flag TIM_FLAG_CC4: TIM Capture Compare 4 Flag TIM_FLAG_COM: TIM Commutation Flag TIM_FLAG_Trigger: TIM Trigger Flag TIM_FLAG_Break: TIM Break Flag TIM_FLAG_CC1OF: TIM Capture Compare 1 overcapture Flag TIM_FLAG_CC2OF: TIM Capture Compare 2 overcapture Flag TIM_FLAG_CC3OF: TIM Capture Compare 3 overcapture Flag TIM_FLAG_CC4OF: TIM Capture Compare 4 overcapture Flag

Note:

• TIM6 and TIM7 can have only one update flag.
• TIM9, TIM12 and TIM15 can have only TIM_FLAG_Update, TIM_FLAG_CC1, TIM_FLAG_CC2 or TIM_FLAG_Trigger.
• TIM10, TIM11, TIM13, TIM14, TIM16 and TIM17 can have TIM_FLAG_Update or TIM_FLAG_CC1.
• TIM_FLAG_Break is used only with TIM1, TIM8 and TIM15.
• TIM_FLAG_COM is used only with TIM1, TIM8, TIM15, TIM16 and TIM17.

Return values:

None

Definition at line 2600 of file stm32f10x_tim.c.

Clears the TIMx's interrupt pending bits.

Parameters:

TIMx,:

where x can be 1 to 17 to select the TIM peripheral.

TIM_IT,:

specifies the pending bit to clear. This parameter can be any combination of the following values: TIM_IT_Update: TIM1 update Interrupt source TIM_IT_CC1: TIM Capture Compare 1 Interrupt source TIM_IT_CC2: TIM Capture Compare 2 Interrupt source TIM_IT_CC3: TIM Capture Compare 3 Interrupt source TIM_IT_CC4: TIM Capture Compare 4 Interrupt source TIM_IT_COM: TIM Commutation Interrupt source TIM_IT_Trigger: TIM Trigger Interrupt source TIM_IT_Break: TIM Break Interrupt source

Note:

• TIM6 and TIM7 can generate only an update interrupt.
• TIM9, TIM12 and TIM15 can have only TIM_IT_Update, TIM_IT_CC1, TIM_IT_CC2 or TIM_IT_Trigger.
• TIM10, TIM11, TIM13, TIM14, TIM16 and TIM17 can have TIM_IT_Update or TIM_IT_CC1.
• TIM_IT_Break is used only with TIM1, TIM8 and TIM15.
• TIM_IT_COM is used only with TIM1, TIM8, TIM15, TIM16 and TIM17.

Return values:

None

Definition at line 2676 of file stm32f10x_tim.c.

Clears or safeguards the OCREF1 signal on an external event.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_OCClear,:	new state of the Output Compare Clear Enable Bit. This parameter can be one of the following values: TIM_OCClear_Enable: TIM Output clear enable TIM_OCClear_Disable: TIM Output clear disable

Return values:

None

Definition at line 1707 of file stm32f10x_tim.c.

Clears or safeguards the OCREF2 signal on an external event.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_OCClear,:	new state of the Output Compare Clear Enable Bit. This parameter can be one of the following values: TIM_OCClear_Enable: TIM Output clear enable TIM_OCClear_Disable: TIM Output clear disable

Return values:

None

Definition at line 1733 of file stm32f10x_tim.c.

Clears or safeguards the OCREF3 signal on an external event.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_OCClear,:	new state of the Output Compare Clear Enable Bit. This parameter can be one of the following values: TIM_OCClear_Enable: TIM Output clear enable TIM_OCClear_Disable: TIM Output clear disable

Return values:

None

Definition at line 1757 of file stm32f10x_tim.c.

Clears or safeguards the OCREF4 signal on an external event.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_OCClear,:	new state of the Output Compare Clear Enable Bit. This parameter can be one of the following values: TIM_OCClear_Enable: TIM Output clear enable TIM_OCClear_Disable: TIM Output clear disable

Return values:

None

Definition at line 1781 of file stm32f10x_tim.c.

Enables or disables the specified TIM peripheral.

Parameters:

TIMx,:	where x can be 1 to 17 to select the TIMx peripheral.
NewState,:	new state of the TIMx peripheral. This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 806 of file stm32f10x_tim.c.

Specifies the TIMx Counter Mode to be used.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_CounterMode,:	specifies the Counter Mode to be used This parameter can be one of the following values: TIM_CounterMode_Up: TIM Up Counting Mode TIM_CounterMode_Down: TIM Down Counting Mode TIM_CounterMode_CenterAligned1: TIM Center Aligned Mode1 TIM_CounterMode_CenterAligned2: TIM Center Aligned Mode2 TIM_CounterMode_CenterAligned3: TIM Center Aligned Mode3

Return values:

None

Definition at line 1199 of file stm32f10x_tim.c.

Enables or disables the TIM peripheral Main Outputs.

Parameters:

TIMx,:	where x can be 1, 8, 15, 16 or 17 to select the TIMx peripheral.
NewState,:	new state of the TIM peripheral Main Outputs. This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 831 of file stm32f10x_tim.c.

Deinitializes the TIMx peripheral registers to their default reset values.

Parameters:

TIMx,:

where x can be 1 to 17 to select the TIM peripheral.

Return values:

None

Definition at line 122 of file stm32f10x_tim.c.

Enables or disables the TIMx's DMA Requests.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 6, 7, 8, 15, 16 or 17 to select the TIM peripheral.
TIM_DMASource,:	specifies the DMA Request sources. This parameter can be any combination of the following values: TIM_DMA_Update: TIM update Interrupt source TIM_DMA_CC1: TIM Capture Compare 1 DMA source TIM_DMA_CC2: TIM Capture Compare 2 DMA source TIM_DMA_CC3: TIM Capture Compare 3 DMA source TIM_DMA_CC4: TIM Capture Compare 4 DMA source TIM_DMA_COM: TIM Commutation DMA source TIM_DMA_Trigger: TIM Trigger DMA source
NewState,:	new state of the DMA Request sources. This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 964 of file stm32f10x_tim.c.

Configures the TIMx's DMA interface.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 15, 16 or 17 to select the TIM peripheral.
TIM_DMABase,:	DMA Base address. This parameter can be one of the following values: TIM_DMABase_CR, TIM_DMABase_CR2, TIM_DMABase_SMCR, TIM_DMABase_DIER, TIM1_DMABase_SR, TIM_DMABase_EGR, TIM_DMABase_CCMR1, TIM_DMABase_CCMR2, TIM_DMABase_CCER, TIM_DMABase_CNT, TIM_DMABase_PSC, TIM_DMABase_ARR, TIM_DMABase_RCR, TIM_DMABase_CCR1, TIM_DMABase_CCR2, TIM_DMABase_CCR3, TIM_DMABase_CCR4, TIM_DMABase_BDTR, TIM_DMABase_DCR.
TIM_DMABurstLength,:	DMA Burst length. This parameter can be one value between: TIM_DMABurstLength_1Transfer and TIM_DMABurstLength_18Transfers.

Return values:

None

Definition at line 937 of file stm32f10x_tim.c.

Configures the TIMx Encoder Interface.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_EncoderMode,:	specifies the TIMx Encoder Mode. This parameter can be one of the following values: TIM_EncoderMode_TI1: Counter counts on TI1FP1 edge depending on TI2FP2 level. TIM_EncoderMode_TI2: Counter counts on TI2FP2 edge depending on TI1FP1 level. TIM_EncoderMode_TI12: Counter counts on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
TIM_IC1Polarity,:	specifies the IC1 Polarity This parameter can be one of the following values: TIM_ICPolarity_Falling: IC Falling edge. TIM_ICPolarity_Rising: IC Rising edge.
TIM_IC2Polarity,:	specifies the IC2 Polarity This parameter can be one of the following values: TIM_ICPolarity_Falling: IC Falling edge. TIM_ICPolarity_Rising: IC Rising edge.

Return values:

None

Definition at line 1264 of file stm32f10x_tim.c.

Configures the External clock Mode1.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_ExtTRGPrescaler,:	The external Trigger Prescaler. This parameter can be one of the following values: TIM_ExtTRGPSC_OFF: ETRP Prescaler OFF. TIM_ExtTRGPSC_DIV2: ETRP frequency divided by 2. TIM_ExtTRGPSC_DIV4: ETRP frequency divided by 4. TIM_ExtTRGPSC_DIV8: ETRP frequency divided by 8.
TIM_ExtTRGPolarity,:	The external Trigger Polarity. This parameter can be one of the following values: TIM_ExtTRGPolarity_Inverted: active low or falling edge active. TIM_ExtTRGPolarity_NonInverted: active high or rising edge active.
ExtTRGFilter,:	External Trigger Filter. This parameter must be a value between 0x00 and 0x0F

Return values:

None

Definition at line 1075 of file stm32f10x_tim.c.

Configures the External clock Mode2.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_ExtTRGPrescaler,:	The external Trigger Prescaler. This parameter can be one of the following values: TIM_ExtTRGPSC_OFF: ETRP Prescaler OFF. TIM_ExtTRGPSC_DIV2: ETRP frequency divided by 2. TIM_ExtTRGPSC_DIV4: ETRP frequency divided by 4. TIM_ExtTRGPSC_DIV8: ETRP frequency divided by 8.
TIM_ExtTRGPolarity,:	The external Trigger Polarity. This parameter can be one of the following values: TIM_ExtTRGPolarity_Inverted: active low or falling edge active. TIM_ExtTRGPolarity_NonInverted: active high or rising edge active.
ExtTRGFilter,:	External Trigger Filter. This parameter must be a value between 0x00 and 0x0F

Return values:

None

Definition at line 1117 of file stm32f10x_tim.c.

Configures the TIMx External Trigger (ETR).

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_ExtTRGPrescaler,:	The external Trigger Prescaler. This parameter can be one of the following values: TIM_ExtTRGPSC_OFF: ETRP Prescaler OFF. TIM_ExtTRGPSC_DIV2: ETRP frequency divided by 2. TIM_ExtTRGPSC_DIV4: ETRP frequency divided by 4. TIM_ExtTRGPSC_DIV8: ETRP frequency divided by 8.
TIM_ExtTRGPolarity,:	The external Trigger Polarity. This parameter can be one of the following values: TIM_ExtTRGPolarity_Inverted: active low or falling edge active. TIM_ExtTRGPolarity_NonInverted: active high or rising edge active.
ExtTRGFilter,:	External Trigger Filter. This parameter must be a value between 0x00 and 0x0F

Return values:

None

Definition at line 1148 of file stm32f10x_tim.c.

Forces the TIMx output 1 waveform to active or inactive level.

Parameters:

TIMx,:	where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
TIM_ForcedAction,:	specifies the forced Action to be set to the output waveform. This parameter can be one of the following values: TIM_ForcedAction_Active: Force active level on OC1REF TIM_ForcedAction_InActive: Force inactive level on OC1REF.

Return values:

None

Definition at line 1315 of file stm32f10x_tim.c.

Forces the TIMx output 2 waveform to active or inactive level.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
TIM_ForcedAction,:	specifies the forced Action to be set to the output waveform. This parameter can be one of the following values: TIM_ForcedAction_Active: Force active level on OC2REF TIM_ForcedAction_InActive: Force inactive level on OC2REF.

Return values:

None

Definition at line 1339 of file stm32f10x_tim.c.

Forces the TIMx output 3 waveform to active or inactive level.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_ForcedAction,:	specifies the forced Action to be set to the output waveform. This parameter can be one of the following values: TIM_ForcedAction_Active: Force active level on OC3REF TIM_ForcedAction_InActive: Force inactive level on OC3REF.

Return values:

None

Definition at line 1363 of file stm32f10x_tim.c.

Forces the TIMx output 4 waveform to active or inactive level.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_ForcedAction,:	specifies the forced Action to be set to the output waveform. This parameter can be one of the following values: TIM_ForcedAction_Active: Force active level on OC4REF TIM_ForcedAction_InActive: Force inactive level on OC4REF.

Return values:

None

Definition at line 1387 of file stm32f10x_tim.c.

Configures the TIMx event to be generate by software.

Parameters:

TIMx,:

where x can be 1 to 17 to select the TIM peripheral.

TIM_EventSource,:

specifies the event source. This parameter can be one or more of the following values: TIM_EventSource_Update: Timer update Event source TIM_EventSource_CC1: Timer Capture Compare 1 Event source TIM_EventSource_CC2: Timer Capture Compare 2 Event source TIM_EventSource_CC3: Timer Capture Compare 3 Event source TIM_EventSource_CC4: Timer Capture Compare 4 Event source TIM_EventSource_COM: Timer COM event source TIM_EventSource_Trigger: Timer Trigger Event source TIM_EventSource_Break: Timer Break event source

Note:

• TIM6 and TIM7 can only generate an update event.
• TIM_EventSource_COM and TIM_EventSource_Break are used only with TIM1 and TIM8.

Return values:

None

Definition at line 909 of file stm32f10x_tim.c.

Gets the TIMx Input Capture 1 value.

Parameters:

TIMx,:

where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.

Return values:

Capture

Compare 1 Register value.

Definition at line 2457 of file stm32f10x_tim.c.

Gets the TIMx Input Capture 2 value.

Parameters:

TIMx,:

where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.

Return values:

Capture

Compare 2 Register value.

Definition at line 2470 of file stm32f10x_tim.c.

Gets the TIMx Input Capture 3 value.

Parameters:

TIMx,:

where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.

Return values:

Capture

Compare 3 Register value.

Definition at line 2483 of file stm32f10x_tim.c.

Gets the TIMx Input Capture 4 value.

Parameters:

TIMx,:

where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.

Return values:

Capture

Compare 4 Register value.

Definition at line 2496 of file stm32f10x_tim.c.

Gets the TIMx Counter value.

Parameters:

TIMx,:

where x can be 1 to 17 to select the TIM peripheral.

Return values:

Counter

Register value.

Definition at line 2509 of file stm32f10x_tim.c.

Checks whether the specified TIM flag is set or not.

Parameters:

TIMx,:

where x can be 1 to 17 to select the TIM peripheral.

TIM_FLAG,:

specifies the flag to check. This parameter can be one of the following values: TIM_FLAG_Update: TIM update Flag TIM_FLAG_CC1: TIM Capture Compare 1 Flag TIM_FLAG_CC2: TIM Capture Compare 2 Flag TIM_FLAG_CC3: TIM Capture Compare 3 Flag TIM_FLAG_CC4: TIM Capture Compare 4 Flag TIM_FLAG_COM: TIM Commutation Flag TIM_FLAG_Trigger: TIM Trigger Flag TIM_FLAG_Break: TIM Break Flag TIM_FLAG_CC1OF: TIM Capture Compare 1 overcapture Flag TIM_FLAG_CC2OF: TIM Capture Compare 2 overcapture Flag TIM_FLAG_CC3OF: TIM Capture Compare 3 overcapture Flag TIM_FLAG_CC4OF: TIM Capture Compare 4 overcapture Flag

Note:

• TIM6 and TIM7 can have only one update flag.
• TIM9, TIM12 and TIM15 can have only TIM_FLAG_Update, TIM_FLAG_CC1, TIM_FLAG_CC2 or TIM_FLAG_Trigger.
• TIM10, TIM11, TIM13, TIM14, TIM16 and TIM17 can have TIM_FLAG_Update or TIM_FLAG_CC1.
• TIM_FLAG_Break is used only with TIM1, TIM8 and TIM15.
• TIM_FLAG_COM is used only with TIM1, TIM8, TIM15, TIM16 and TIM17.

Return values:

The	new state of TIM_FLAG (SET or RESET).

Definition at line 2556 of file stm32f10x_tim.c.

Checks whether the TIM interrupt has occurred or not.

Parameters:

TIMx,:

where x can be 1 to 17 to select the TIM peripheral.

TIM_IT,:

specifies the TIM interrupt source to check. This parameter can be one of the following values: TIM_IT_Update: TIM update Interrupt source TIM_IT_CC1: TIM Capture Compare 1 Interrupt source TIM_IT_CC2: TIM Capture Compare 2 Interrupt source TIM_IT_CC3: TIM Capture Compare 3 Interrupt source TIM_IT_CC4: TIM Capture Compare 4 Interrupt source TIM_IT_COM: TIM Commutation Interrupt source TIM_IT_Trigger: TIM Trigger Interrupt source TIM_IT_Break: TIM Break Interrupt source

Note:

• TIM6 and TIM7 can generate only an update interrupt.
• TIM9, TIM12 and TIM15 can have only TIM_IT_Update, TIM_IT_CC1, TIM_IT_CC2 or TIM_IT_Trigger.
• TIM10, TIM11, TIM13, TIM14, TIM16 and TIM17 can have TIM_IT_Update or TIM_IT_CC1.
• TIM_IT_Break is used only with TIM1, TIM8 and TIM15.
• TIM_IT_COM is used only with TIM1, TIM8, TIM15, TIM16 and TIM17.

Return values:

The	new state of the TIM_IT(SET or RESET).

Definition at line 2632 of file stm32f10x_tim.c.

Gets the TIMx Prescaler value.

Parameters:

TIMx,:

where x can be 1 to 17 to select the TIM peripheral.

Return values:

Prescaler

Register value.

Definition at line 2522 of file stm32f10x_tim.c.

Initializes the TIM peripheral according to the specified parameters in the TIM_ICInitStruct.

Parameters:

TIMx,:	where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
TIM_ICInitStruct,:	pointer to a TIM_ICInitTypeDef structure that contains the configuration information for the specified TIM peripheral.

Return values:

None

Definition at line 587 of file stm32f10x_tim.c.

Fills each TIM_ICInitStruct member with its default value.

Parameters:

TIM_ICInitStruct,:

pointer to a TIM_ICInitTypeDef structure which will be initialized.

Return values:

None

Definition at line 771 of file stm32f10x_tim.c.

Configures the TIMx internal Clock.

Parameters:

TIMx,:

where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.

Return values:

None

Definition at line 989 of file stm32f10x_tim.c.

Enables or disables the specified TIM interrupts.

Parameters:

TIMx,:

where x can be 1 to 17 to select the TIMx peripheral.

TIM_IT,:

specifies the TIM interrupts sources to be enabled or disabled. This parameter can be any combination of the following values: TIM_IT_Update: TIM update Interrupt source TIM_IT_CC1: TIM Capture Compare 1 Interrupt source TIM_IT_CC2: TIM Capture Compare 2 Interrupt source TIM_IT_CC3: TIM Capture Compare 3 Interrupt source TIM_IT_CC4: TIM Capture Compare 4 Interrupt source TIM_IT_COM: TIM Commutation Interrupt source TIM_IT_Trigger: TIM Trigger Interrupt source TIM_IT_Break: TIM Break Interrupt source

Note:

• TIM6 and TIM7 can only generate an update interrupt.
• TIM9, TIM12 and TIM15 can have only TIM_IT_Update, TIM_IT_CC1, TIM_IT_CC2 or TIM_IT_Trigger.
• TIM10, TIM11, TIM13, TIM14, TIM16 and TIM17 can have TIM_IT_Update or TIM_IT_CC1.
• TIM_IT_Break is used only with TIM1, TIM8 and TIM15.
• TIM_IT_COM is used only with TIM1, TIM8, TIM15, TIM16 and TIM17.

Parameters:

NewState,:

new state of the TIM interrupts. This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 872 of file stm32f10x_tim.c.

Configures the TIMx Internal Trigger as External Clock.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 9, 12 or 15 to select the TIM peripheral.
TIM_ITRSource,:	Trigger source. This parameter can be one of the following values:
TIM_TS_ITR0,:	Internal Trigger 0
TIM_TS_ITR1,:	Internal Trigger 1
TIM_TS_ITR2,:	Internal Trigger 2
TIM_TS_ITR3,:	Internal Trigger 3

Return values:

None

Definition at line 1008 of file stm32f10x_tim.c.

Configures the TIMx Output Compare 1 Fast feature.

Parameters:

TIMx,:	where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
TIM_OCFast,:	new state of the Output Compare Fast Enable Bit. This parameter can be one of the following values: TIM_OCFast_Enable: TIM output compare fast enable TIM_OCFast_Disable: TIM output compare fast disable

Return values:

None

Definition at line 1606 of file stm32f10x_tim.c.

Initializes the TIMx Channel1 according to the specified parameters in the TIM_OCInitStruct.

Parameters:

TIMx,:	where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
TIM_OCInitStruct,:	pointer to a TIM_OCInitTypeDef structure that contains the configuration information for the specified TIM peripheral.

Return values:

None

Definition at line 279 of file stm32f10x_tim.c.

Configures the TIMx Channel 1N polarity.

Parameters:

TIMx,:	where x can be 1, 8, 15, 16 or 17 to select the TIM peripheral.
TIM_OCNPolarity,:	specifies the OC1N Polarity This parameter can be one of the following values: TIM_OCNPolarity_High: Output Compare active high TIM_OCNPolarity_Low: Output Compare active low

Return values:

None

Definition at line 1828 of file stm32f10x_tim.c.

Configures the TIMx channel 1 polarity.

Parameters:

TIMx,:	where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
TIM_OCPolarity,:	specifies the OC1 Polarity This parameter can be one of the following values: TIM_OCPolarity_High: Output Compare active high TIM_OCPolarity_Low: Output Compare active low

Return values:

None

Definition at line 1805 of file stm32f10x_tim.c.

Enables or disables the TIMx peripheral Preload register on CCR1.

Parameters:

TIMx,:	where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
TIM_OCPreload,:	new state of the TIMx peripheral Preload register This parameter can be one of the following values: TIM_OCPreload_Enable TIM_OCPreload_Disable

Return values:

None

Definition at line 1509 of file stm32f10x_tim.c.

Configures the TIMx Output Compare 2 Fast feature.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
TIM_OCFast,:	new state of the Output Compare Fast Enable Bit. This parameter can be one of the following values: TIM_OCFast_Enable: TIM output compare fast enable TIM_OCFast_Disable: TIM output compare fast disable

Return values:

None

Definition at line 1632 of file stm32f10x_tim.c.

Initializes the TIMx Channel2 according to the specified parameters in the TIM_OCInitStruct.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
TIM_OCInitStruct,:	pointer to a TIM_OCInitTypeDef structure that contains the configuration information for the specified TIM peripheral.

Return values:

None

Definition at line 362 of file stm32f10x_tim.c.

Configures the TIMx Channel 2N polarity.

Parameters:

TIMx,:	where x can be 1 or 8 to select the TIM peripheral.
TIM_OCNPolarity,:	specifies the OC2N Polarity This parameter can be one of the following values: TIM_OCNPolarity_High: Output Compare active high TIM_OCNPolarity_Low: Output Compare active low

Return values:

None

Definition at line 1875 of file stm32f10x_tim.c.

Configures the TIMx channel 2 polarity.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
TIM_OCPolarity,:	specifies the OC2 Polarity This parameter can be one of the following values: TIM_OCPolarity_High: Output Compare active high TIM_OCPolarity_Low: Output Compare active low

Return values:

None

Definition at line 1852 of file stm32f10x_tim.c.

Enables or disables the TIMx peripheral Preload register on CCR2.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
TIM_OCPreload,:	new state of the TIMx peripheral Preload register This parameter can be one of the following values: TIM_OCPreload_Enable TIM_OCPreload_Disable

Return values:

None

Definition at line 1534 of file stm32f10x_tim.c.

Configures the TIMx Output Compare 3 Fast feature.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_OCFast,:	new state of the Output Compare Fast Enable Bit. This parameter can be one of the following values: TIM_OCFast_Enable: TIM output compare fast enable TIM_OCFast_Disable: TIM output compare fast disable

Return values:

None

Definition at line 1657 of file stm32f10x_tim.c.

Initializes the TIMx Channel3 according to the specified parameters in the TIM_OCInitStruct.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_OCInitStruct,:	pointer to a TIM_OCInitTypeDef structure that contains the configuration information for the specified TIM peripheral.

Return values:

None

Definition at line 444 of file stm32f10x_tim.c.

Configures the TIMx Channel 3N polarity.

Parameters:

TIMx,:	where x can be 1 or 8 to select the TIM peripheral.
TIM_OCNPolarity,:	specifies the OC3N Polarity This parameter can be one of the following values: TIM_OCNPolarity_High: Output Compare active high TIM_OCNPolarity_Low: Output Compare active low

Return values:

None

Definition at line 1922 of file stm32f10x_tim.c.

Configures the TIMx channel 3 polarity.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_OCPolarity,:	specifies the OC3 Polarity This parameter can be one of the following values: TIM_OCPolarity_High: Output Compare active high TIM_OCPolarity_Low: Output Compare active low

Return values:

None

Definition at line 1899 of file stm32f10x_tim.c.

Enables or disables the TIMx peripheral Preload register on CCR3.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_OCPreload,:	new state of the TIMx peripheral Preload register This parameter can be one of the following values: TIM_OCPreload_Enable TIM_OCPreload_Disable

Return values:

None

Definition at line 1558 of file stm32f10x_tim.c.

Configures the TIMx Output Compare 4 Fast feature.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_OCFast,:	new state of the Output Compare Fast Enable Bit. This parameter can be one of the following values: TIM_OCFast_Enable: TIM output compare fast enable TIM_OCFast_Disable: TIM output compare fast disable

Return values:

None

Definition at line 1682 of file stm32f10x_tim.c.

Initializes the TIMx Channel4 according to the specified parameters in the TIM_OCInitStruct.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_OCInitStruct,:	pointer to a TIM_OCInitTypeDef structure that contains the configuration information for the specified TIM peripheral.

Return values:

None

Definition at line 523 of file stm32f10x_tim.c.

Configures the TIMx channel 4 polarity.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_OCPolarity,:	specifies the OC4 Polarity This parameter can be one of the following values: TIM_OCPolarity_High: Output Compare active high TIM_OCPolarity_Low: Output Compare active low

Return values:

None

Definition at line 1947 of file stm32f10x_tim.c.

Enables or disables the TIMx peripheral Preload register on CCR4.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_OCPreload,:	new state of the TIMx peripheral Preload register This parameter can be one of the following values: TIM_OCPreload_Enable TIM_OCPreload_Disable

Return values:

None

Definition at line 1582 of file stm32f10x_tim.c.

Fills each TIM_OCInitStruct member with its default value.

Parameters:

TIM_OCInitStruct

: pointer to a TIM_OCInitTypeDef structure which will be initialized.

Return values:

None

Definition at line 752 of file stm32f10x_tim.c.

Configures the TIMx Prescaler.

Parameters:

TIMx,:	where x can be 1 to 17 to select the TIM peripheral.
Prescaler,:	specifies the Prescaler Register value
TIM_PSCReloadMode,:	specifies the TIM Prescaler Reload mode This parameter can be one of the following values: TIM_PSCReloadMode_Update: The Prescaler is loaded at the update event. TIM_PSCReloadMode_Immediate: The Prescaler is loaded immediately.

Return values:

None

Definition at line 1176 of file stm32f10x_tim.c.

Configures the TIM peripheral according to the specified parameters in the TIM_ICInitStruct to measure an external PWM signal.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
TIM_ICInitStruct,:	pointer to a TIM_ICInitTypeDef structure that contains the configuration information for the specified TIM peripheral.

Return values:

None

Definition at line 654 of file stm32f10x_tim.c.

Selects the TIMx peripheral Capture Compare DMA source.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 15, 16 or 17 to select the TIM peripheral.
NewState,:	new state of the Capture Compare DMA source This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 1458 of file stm32f10x_tim.c.

Selects the TIM peripheral Commutation event.

Parameters:

TIMx,:	where x can be 1, 8, 15, 16 or 17 to select the TIMx peripheral
NewState,:	new state of the Commutation event. This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 1433 of file stm32f10x_tim.c.

Enables or disables the TIMx's Hall sensor interface.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
NewState,:	new state of the TIMx Hall sensor interface. This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 2144 of file stm32f10x_tim.c.

Selects the Input Trigger source.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
TIM_InputTriggerSource,:	The Input Trigger source. This parameter can be one of the following values: TIM_TS_ITR0: Internal Trigger 0 TIM_TS_ITR1: Internal Trigger 1 TIM_TS_ITR2: Internal Trigger 2 TIM_TS_ITR3: Internal Trigger 3 TIM_TS_TI1F_ED: TI1 Edge Detector TIM_TS_TI1FP1: Filtered Timer Input 1 TIM_TS_TI2FP2: Filtered Timer Input 2 TIM_TS_ETRF: External Trigger input

Return values:

None

Definition at line 1229 of file stm32f10x_tim.c.

Sets or Resets the TIMx Master/Slave Mode.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
TIM_MasterSlaveMode,:	specifies the Timer Master Slave Mode. This parameter can be one of the following values: TIM_MasterSlaveMode_Enable: synchronization between the current timer and its slaves (through TRGO). TIM_MasterSlaveMode_Disable: No action

Return values:

None

Definition at line 2246 of file stm32f10x_tim.c.

Selects the TIM Output Compare Mode.

Note:

This function disables the selected channel before changing the Output Compare Mode. User has to enable this channel using TIM_CCxCmd and TIM_CCxNCmd functions.

Parameters:

TIMx,:	where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
TIM_Channel,:	specifies the TIM Channel This parameter can be one of the following values: TIM_Channel_1: TIM Channel 1 TIM_Channel_2: TIM Channel 2 TIM_Channel_3: TIM Channel 3 TIM_Channel_4: TIM Channel 4
TIM_OCMode,:	specifies the TIM Output Compare Mode. This parameter can be one of the following values: TIM_OCMode_Timing TIM_OCMode_Active TIM_OCMode_Toggle TIM_OCMode_PWM1 TIM_OCMode_PWM2 TIM_ForcedAction_Active TIM_ForcedAction_InActive

Return values:

None

Definition at line 2045 of file stm32f10x_tim.c.

Selects the TIMx's One Pulse Mode.

Parameters:

TIMx,:	where x can be 1 to 17 to select the TIM peripheral.
TIM_OPMode,:	specifies the OPM Mode to be used. This parameter can be one of the following values: TIM_OPMode_Single TIM_OPMode_Repetitive

Return values:

None

Definition at line 2170 of file stm32f10x_tim.c.

Selects the TIMx Trigger Output Mode.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 6, 7, 8, 9, 12 or 15 to select the TIM peripheral.
TIM_TRGOSource,:	specifies the Trigger Output source. This paramter can be one of the following values:

• For all TIMx
  • TIM_TRGOSource_Reset: The UG bit in the TIM_EGR register is used as the trigger output (TRGO).
  • TIM_TRGOSource_Enable: The Counter Enable CEN is used as the trigger output (TRGO).
  • TIM_TRGOSource_Update: The update event is selected as the trigger output (TRGO).
• For all TIMx except TIM6 and TIM7
  • TIM_TRGOSource_OC1: The trigger output sends a positive pulse when the CC1IF flag is to be set, as soon as a capture or compare match occurs (TRGO).
  • TIM_TRGOSource_OC1Ref: OC1REF signal is used as the trigger output (TRGO).
  • TIM_TRGOSource_OC2Ref: OC2REF signal is used as the trigger output (TRGO).
  • TIM_TRGOSource_OC3Ref: OC3REF signal is used as the trigger output (TRGO).
  • TIM_TRGOSource_OC4Ref: OC4REF signal is used as the trigger output (TRGO).

  Return values:

  None

Definition at line 2202 of file stm32f10x_tim.c.

Selects the TIMx Slave Mode.

Parameters:

TIMx,:

where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.

TIM_SlaveMode,:

specifies the Timer Slave Mode. This parameter can be one of the following values: TIM_SlaveMode_Reset: Rising edge of the selected trigger signal (TRGI) re-initializes the counter and triggers an update of the registers. TIM_SlaveMode_Gated: The counter clock is enabled when the trigger signal (TRGI) is high. TIM_SlaveMode_Trigger: The counter starts at a rising edge of the trigger TRGI. TIM_SlaveMode_External1: Rising edges of the selected trigger (TRGI) clock the counter.

Return values:

None

Definition at line 2225 of file stm32f10x_tim.c.

Sets the TIMx Autoreload Register value.

Parameters:

TIMx,:	where x can be 1 to 17 to select the TIM peripheral.
Autoreload,:	specifies the Autoreload register new value.

Return values:

None

Definition at line 2278 of file stm32f10x_tim.c.

Sets the TIMx Clock Division value.

Parameters:

TIMx,:	where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
TIM_CKD,:	specifies the clock division value. This parameter can be one of the following value: TIM_CKD_DIV1: TDTS = Tck_tim TIM_CKD_DIV2: TDTS = 2*Tck_tim TIM_CKD_DIV4: TDTS = 4*Tck_tim

Return values:

None

Definition at line 2441 of file stm32f10x_tim.c.

Sets the TIMx Capture Compare1 Register value.

Parameters:

TIMx,:	where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
Compare1,:	specifies the Capture Compare1 register new value.

Return values:

None

Definition at line 2292 of file stm32f10x_tim.c.

Sets the TIMx Capture Compare2 Register value.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
Compare2,:	specifies the Capture Compare2 register new value.

Return values:

None

Definition at line 2306 of file stm32f10x_tim.c.

Sets the TIMx Capture Compare3 Register value.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
Compare3,:	specifies the Capture Compare3 register new value.

Return values:

None

Definition at line 2320 of file stm32f10x_tim.c.

Sets the TIMx Capture Compare4 Register value.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
Compare4,:	specifies the Capture Compare4 register new value.

Return values:

None

Definition at line 2334 of file stm32f10x_tim.c.

Sets the TIMx Counter Register value.

Parameters:

TIMx,:	where x can be 1 to 17 to select the TIM peripheral.
Counter,:	specifies the Counter register new value.

Return values:

None

Definition at line 2264 of file stm32f10x_tim.c.

Sets the TIMx Input Capture 1 prescaler.

Parameters:

TIMx,:	where x can be 1 to 17 except 6 and 7 to select the TIM peripheral.
TIM_ICPSC,:	specifies the Input Capture1 prescaler new value. This parameter can be one of the following values: TIM_ICPSC_DIV1: no prescaler TIM_ICPSC_DIV2: capture is done once every 2 events TIM_ICPSC_DIV4: capture is done once every 4 events TIM_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 2353 of file stm32f10x_tim.c.

Sets the TIMx Input Capture 2 prescaler.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 8, 9, 12 or 15 to select the TIM peripheral.
TIM_ICPSC,:	specifies the Input Capture2 prescaler new value. This parameter can be one of the following values: TIM_ICPSC_DIV1: no prescaler TIM_ICPSC_DIV2: capture is done once every 2 events TIM_ICPSC_DIV4: capture is done once every 4 events TIM_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 2375 of file stm32f10x_tim.c.

Sets the TIMx Input Capture 3 prescaler.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_ICPSC,:	specifies the Input Capture3 prescaler new value. This parameter can be one of the following values: TIM_ICPSC_DIV1: no prescaler TIM_ICPSC_DIV2: capture is done once every 2 events TIM_ICPSC_DIV4: capture is done once every 4 events TIM_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 2397 of file stm32f10x_tim.c.

Sets the TIMx Input Capture 4 prescaler.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5 or 8 to select the TIM peripheral.
TIM_ICPSC,:	specifies the Input Capture4 prescaler new value. This parameter can be one of the following values: TIM_ICPSC_DIV1: no prescaler TIM_ICPSC_DIV2: capture is done once every 2 events TIM_ICPSC_DIV4: capture is done once every 4 events TIM_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 2419 of file stm32f10x_tim.c.

Initializes the TIMx Time Base Unit peripheral according to the specified parameters in the TIM_TimeBaseInitStruct.

Parameters:

TIMx,:	where x can be 1 to 17 to select the TIM peripheral.
TIM_TimeBaseInitStruct,:	pointer to a TIM_TimeBaseInitTypeDef structure that contains the configuration information for the specified TIM peripheral.

Return values:

None

Definition at line 226 of file stm32f10x_tim.c.

Fills each TIM_TimeBaseInitStruct member with its default value.

Parameters:

TIM_TimeBaseInitStruct

: pointer to a TIM_TimeBaseInitTypeDef structure which will be initialized.

Return values:

None

Definition at line 736 of file stm32f10x_tim.c.

Configures the TIMx Trigger as External Clock.

Parameters:

TIMx,:	where x can be 1, 2, 3, 4, 5, 9, 12 or 15 to select the TIM peripheral.
TIM_TIxExternalCLKSource,:	Trigger source. This parameter can be one of the following values: TIM_TIxExternalCLK1Source_TI1ED: TI1 Edge Detector TIM_TIxExternalCLK1Source_TI1: Filtered Timer Input 1 TIM_TIxExternalCLK1Source_TI2: Filtered Timer Input 2
TIM_ICPolarity,:	specifies the TIx Polarity. This parameter can be one of the following values: TIM_ICPolarity_Rising TIM_ICPolarity_Falling
ICFilter	: specifies the filter value. This parameter must be a value between 0x0 and 0xF.

Return values:

None

Definition at line 1035 of file stm32f10x_tim.c.

Enables or Disables the TIMx Update event.

Parameters:

TIMx,:	where x can be 1 to 17 to select the TIM peripheral.
NewState,:	new state of the TIMx UDIS bit This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 2092 of file stm32f10x_tim.c.

Configures the TIMx Update Request Interrupt source.

Parameters:

TIMx,:	where x can be 1 to 17 to select the TIM peripheral.
TIM_UpdateSource,:	specifies the Update source. This parameter can be one of the following values: TIM_UpdateSource_Regular: Source of update is the counter overflow/underflow or the setting of UG bit, or an update generation through the slave mode controller. TIM_UpdateSource_Global: Source of update is counter overflow/underflow.

Return values:

None

Definition at line 2120 of file stm32f10x_tim.c.