Diff: I2CTextLCD.cpp

Revision:

0:9d621b44ea24

Child:

1:e60cbc407d73

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/I2CTextLCD.cpp	Thu Aug 18 08:52:06 2011 +0000
@@ -0,0 +1,223 @@
+/* mbed I2CTextLCD Library
+ * Copyright (c) 2007-2009 sford
+ * Copyright (c) 2010 Wim De Roeve  changed to work with I2C PCF8575
+ * Released under the MIT License: http://mbed.org/license/mit
+ */
+
+#include "I2CTextLCD.h"
+#include "mbed.h"
+#include "error.h"
+
+using namespace mbed;
+
+/*
+     * useful info found at http://www.a-netz.de/lcd.en.php
+     *
+     *
+     * Initialisation
+     * ==============
+     *
+     * After attaching the supply voltage/after a reset, the display needs to be brought in to a defined state
+     *
+     * - wait approximately 15 ms so the display is ready to execute commands
+     * - Execute the command 0x30 ("Display Settings") three times (wait 1,64ms after each command, the busy flag cannot be queried now).
+     * - The display is in 8 bit mode, so if you have only connected 4 data pins you should only transmit the higher nibble of each command.
+     * - If you want to use the 4 bit mode, now you can execute the command to switch over to this mode now.
+         * - Execute the "clear display" command
+     *
+     * Timing
+     * ======
+     *
+     * Nearly all commands transmitted to the display need 40us for execution.
+     * Exceptions are the commands "Clear Display and Reset" and "Set Cursor to Start Position"
+     * These commands need 1.64ms for execution. These timings are valid for all displays working with an
+     * internal clock of 250kHz. But I do not know any displays that use other frequencies. Any time you
+     * can use the busy flag to test if the display is ready to accept the next command.
+     *
+     */
+
+I2CTextLCD::I2CTextLCD(PinName sda, PinName scl, int i2cAddress , int columns, int rows,
+                       bool backlight) : _i2c(sda, scl) {
+
+    _i2cAddress = i2cAddress;
+    _columns = columns;
+    _rows = rows;
+    _backlight=backlight;
+    _i2c.frequency(70000);
+  
+
+    // Should theoretically wait 15ms, but most things will be powered up pre-reset
+    // so i'll disable that for the minute. If implemented, could wait 15ms post reset
+    // instead
+    // Winstar 20x4 WH2004-NYG- needs 40ms after VDD> 4,5V
+     wait(0.05);
+
+    // send "Display Settings" 3 times (Only top nibble of 0x30 as we've got 4-bit bus)
+
+    for (int i=0; i<3; i++) {
+     writeCommand(0x3); //send 3 times mode
+        wait(0.00164);      // this command takes 1.64ms, so wait for it
+    }
+    writeCommand(0x2); // 4-bit mode
+    writeCommand(0x2); // 4-bit mode
+
+    writeCommand(0x28);    // Function set 001 BW N F - -
+    wait(0.001);
+    writeCommand(0x28);    // Function set 001 BW N F
+    wait(0.001);
+    writeCommand(0x0C); // turns display ON, no cursor. Use 0x0E for cursor ON.
+    /* 0x28 also works for Winstar WEH002004ALPP5N00000 OLED display. 0x29= westEuro fon table, 0x2A = UK/Russian
+*/
+    // Added RC 2011-8-11
+    writeCommand(0x01); // clear display RAM all to 00
+    wait(0.007);        // 6.2ms specified for OLED display to recover from RAM clear
+    
+    writeCommand(0x06);  //  Cursor Direction and Display Shift : 0000 01 CD S (CD 0-left, 1-right S(hift) 0-no, 1-yes
+
+    cls();
+
+
+}
+
+int I2CTextLCD::_putc(int value) {
+    if (value == '\n') {
+        newline();
+    } else {
+        writeData(value);
+    }
+    return value;
+}
+
+int I2CTextLCD::_getc() {
+    return 0;
+}
+
+/* void I2CTextLCD::backlight(bool status) {
+    _backlight=status;
+    if (_backlight)
+        writeI2CByte(BACKLIGHT_ON | E1_ON);
+    else
+        writeI2CByte(E1_ON);
+}
+*/
+
+void I2CTextLCD::newline() {
+    _column = 0;
+    _row++;
+    if (_row >= _rows) {
+        _row = 0;
+    }
+    locate(_column, _row);
+}
+
+void I2CTextLCD::locate(int column, int row) {
+    if (column < 0 || column >= _columns || row < 0 || row >= _rows) {
+        error("locate(%d,%d) out of range on %dx%d display", column, row, _columns, _rows);
+        return;
+    }
+    _row = row;
+    _column = column;
+    int address;
+    if (row==0){
+    address = 0x80+_column;
+    }
+    else if (row==1){
+    address= 0xc0+_column;
+    }
+    else if (row==2){
+    address=0x94+_column;
+    }
+    else if(row==3){
+    address=0xd4+_column;
+    }
+    /*
+    int address = 0x80 + (_row * 40) + _column; // memory starts at 0x00, and is 40 chars long per row
+    Set bit 7 also, to signify  ADDRESS SET mode.
+     // pc_LCD.traceOut("locate %dx%d\r\n", column, row);
+     */
+    writeCommand(address);  // must set bit 7 to indicate address SET command
+    wait(0.004);      // takes 1.5ms on Winstar LCD 20x4
+}
+
+void I2CTextLCD::cls() {
+    writeCommand(0x01); // Clear Display
+    wait(0.007f);     // This command takes 1.64 ms (LCD), 6.2ms for Winstar OLED
+    locate(0, 0);
+}
+
+void I2CTextLCD::reset() {
+    cls();
+}
+
+void I2CTextLCD::writeByte(int c, bool rs) {
+   // void writeByte(char c, bool rs){
+      char cmd[2]; //led = 1;
+        cmd[0]=c>>2;                  // upper nibble
+        cmd[0]=cmd[0] & 0x3c;
+        cmd[1]=c<<2;                 // lower nibble
+        cmd[1]=cmd[1] & 0x3c;
+        if (rs) {
+        cmd[0]=cmd[0] | 0x01;
+        cmd[1]=cmd[1] | 0x01;
+        }
+        _i2c.write( _i2cAddress,cmd,1); // E=0, write upper nibble
+        wait_us(1);
+        cmd[0]=cmd[0]|0x02; //E=1
+        _i2c.write( _i2cAddress, cmd,1); 
+        wait_us(1);
+        cmd[0]=cmd[0]&0x3d; //E=0, RS preserved in bit 0
+        _i2c.write( _i2cAddress, cmd,1); 
+        wait_us(1);
+        cmd[0]=cmd[1]; //E=0, write lower nibble
+        wait_us(1);
+        cmd[0]=cmd[0]|0x02; //E=1
+        _i2c.write( _i2cAddress, cmd,1); 
+        wait_us(1);
+        cmd[0]=cmd[0]&0x3d; //E=0, RS preserved in bit 0
+        _i2c.write( _i2cAddress, cmd,1);
+        _i2c.write ( _i2cAddress,cmd,1);              
+        // led = 0;
+        wait_us(1);
+    }
+    //void I2CTextLCD::writeByte(int data, bool rs) {
+
+
+/*
+    writeNibble(data >> 4 , rs);
+    writeNibble(data >> 0 , rs);
+    RC 2011-8-11. change to d4..d7 - PCF8574 ports P2 .. P5
+*/
+//data = data>>2;
+//data = data & 0x3c;
+//writeNibble(data , rs);
+//data = data<<2;
+//data = data & 0x3c;
+//writeNibble(data , rs);
+
+void I2CTextLCD::writeCommand(int command) {
+    // RS = 0;
+    writeByte(command,false);
+}
+
+void I2CTextLCD::writeData(int data) {
+    //RS = 1
+    writeByte(data,true);
+
+    _column++;
+    if (_column >= _columns) {
+        newline();
+    }
+}
+
+/* void I2CTextLCD::writeI2CByte(int data) {
+    char cmd[2];
+    cmd[0] = (data & 0xFF);
+    cmd[1] = (data >> 8);
+     _i2c.write(_i2cAddress, cmd, 2);
+*/
+
+
+
+
+
+