Nick Zhou
mbed library sources change for ST sensors and ST BLE
Fork of
mbed-src
by 
mbed official
Diff: targets/hal/TARGET_STM/TARGET_STM32F1/pinmap.c
- Revision:
- 508:4f5903e025e6
- Parent:
- 489:119543c9f674
- Child:
- 537:c61a9ac6f5c2
diff -r d4fc7603a669 -r 4f5903e025e6 targets/hal/TARGET_STM/TARGET_STM32F1/pinmap.c
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/hal/TARGET_STM/TARGET_STM32F1/pinmap.c Thu Apr 09 06:45:08 2015 +0100
@@ -0,0 +1,202 @@
+/* mbed Microcontroller Library
+ *******************************************************************************
+ * Copyright (c) 2014, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ */
+#include "mbed_assert.h"
+#include "pinmap.h"
+#include "PortNames.h"
+#include "mbed_error.h"
+
+// GPIO mode look-up table
+// Warning: the elements order must be the same as the one defined in PinNames.h
+static const uint32_t gpio_mode[13] = {
+ GPIO_MODE_INPUT, // 0 = STM_MODE_INPUT
+ GPIO_MODE_OUTPUT_PP, // 1 = STM_MODE_OUTPUT_PP
+ GPIO_MODE_OUTPUT_OD, // 2 = STM_MODE_OUTPUT_OD
+ GPIO_MODE_AF_PP, // 3 = STM_MODE_AF_PP
+ GPIO_MODE_AF_OD, // 4 = STM_MODE_AF_OD
+ GPIO_MODE_ANALOG, // 5 = STM_MODE_ANALOG
+ GPIO_MODE_IT_RISING, // 6 = STM_MODE_IT_RISING
+ GPIO_MODE_IT_FALLING, // 7 = STM_MODE_IT_FALLING
+ GPIO_MODE_IT_RISING_FALLING, // 8 = STM_MODE_IT_RISING_FALLING
+ GPIO_MODE_EVT_RISING, // 9 = STM_MODE_EVT_RISING
+ GPIO_MODE_EVT_FALLING, // 10 = STM_MODE_EVT_FALLING
+ GPIO_MODE_EVT_RISING_FALLING, // 11 = STM_MODE_EVT_RISING_FALLING
+ 0x10000000 // 12 = STM_MODE_IT_EVT_RESET (not in STM32Cube HAL)
+};
+
+// Enable GPIO clock and return GPIO base address
+uint32_t Set_GPIO_Clock(uint32_t port_idx)
+{
+ uint32_t gpio_add = 0;
+ switch (port_idx) {
+ case PortA:
+ gpio_add = GPIOA_BASE;
+ __GPIOA_CLK_ENABLE();
+ break;
+ case PortB:
+ gpio_add = GPIOB_BASE;
+ __GPIOB_CLK_ENABLE();
+ break;
+ case PortC:
+ gpio_add = GPIOC_BASE;
+ __GPIOC_CLK_ENABLE();
+ break;
+ case PortD:
+ gpio_add = GPIOD_BASE;
+ __GPIOD_CLK_ENABLE();
+ break;
+ default:
+ error("Pinmap error: wrong port number.");
+ break;
+ }
+ return gpio_add;
+}
+
+/**
+ * Configure pin (input, output, alternate function or analog) + output speed + AF
+ */
+void pin_function(PinName pin, int data)
+{
+ MBED_ASSERT(pin != (PinName)NC);
+ // Get the pin informations
+ uint32_t mode = STM_PIN_MODE(data);
+ uint32_t pupd = STM_PIN_PUPD(data);
+ uint32_t afnum = STM_PIN_AFNUM(data);
+
+ uint32_t port_index = STM_PORT(pin);
+ uint32_t pin_index = STM_PIN(pin);
+
+ // Enable GPIO clock
+ uint32_t gpio_add = Set_GPIO_Clock(port_index);
+ GPIO_TypeDef *gpio = (GPIO_TypeDef *)gpio_add;
+
+ // Enable AFIO clock
+ __HAL_RCC_AFIO_CLK_ENABLE();
+
+ // Configure Alternate Function
+ // Warning: Must be done before the GPIO is initialized
+ if (afnum > 0) {
+ switch (afnum) {
+ case 1: // Remap SPI1
+ __HAL_AFIO_REMAP_SPI1_ENABLE();
+ break;
+ case 2: // Remap I2C1
+ __HAL_AFIO_REMAP_I2C1_ENABLE();
+ break;
+ case 3: // Remap USART1
+ __HAL_AFIO_REMAP_USART1_ENABLE();
+ break;
+ case 4: // Remap USART2
+ __HAL_AFIO_REMAP_USART2_ENABLE();
+ break;
+ case 5: // Partial Remap USART3
+ __HAL_AFIO_REMAP_USART3_PARTIAL();
+ break;
+ case 6: // Partial Remap TIM1
+ __HAL_AFIO_REMAP_TIM1_PARTIAL();
+ break;
+ case 7: // Partial Remap TIM3
+ __HAL_AFIO_REMAP_TIM3_PARTIAL();
+ break;
+ case 8: // Full Remap TIM2
+ __HAL_AFIO_REMAP_TIM2_ENABLE();
+ break;
+ case 9: // Full Remap TIM3
+ __HAL_AFIO_REMAP_TIM3_ENABLE();
+ break;
+ default:
+ break;
+ }
+ }
+
+ // Configure GPIO
+ GPIO_InitTypeDef GPIO_InitStructure;
+ GPIO_InitStructure.Pin = (uint32_t)(1 << pin_index);
+ GPIO_InitStructure.Mode = gpio_mode[mode];
+ GPIO_InitStructure.Pull = pupd;
+ GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;
+ HAL_GPIO_Init(gpio, &GPIO_InitStructure);
+
+ // Disconnect JTAG-DP + SW-DP signals.
+ // Warning: Need to reconnect under reset
+ if ((pin == PA_13) || (pin == PA_14)) {
+ __HAL_AFIO_REMAP_SWJ_DISABLE(); // JTAG-DP Disabled and SW-DP Disabled
+ }
+ if ((pin == PA_15) || (pin == PB_3) || (pin == PB_4)) {
+ __HAL_AFIO_REMAP_SWJ_NOJTAG(); // JTAG-DP Disabled and SW-DP enabled
+ }
+}
+
+/**
+ * Configure pin pull-up/pull-down
+ */
+void pin_mode(PinName pin, PinMode mode)
+{
+ MBED_ASSERT(pin != (PinName)NC);
+
+ uint32_t port_index = STM_PORT(pin);
+ uint32_t pin_index = STM_PIN(pin);
+
+ // Enable GPIO clock
+ uint32_t gpio_add = Set_GPIO_Clock(port_index);
+ GPIO_TypeDef *gpio = (GPIO_TypeDef *)gpio_add;
+
+ // Configure open-drain and pull-up/down
+ switch (mode) {
+ case PullNone:
+ break;
+ case PullUp:
+ case PullDown:
+ // Set pull-up / pull-down for Input mode
+ if (pin_index < 8) {
+ if ((gpio->CRL & (0x03 << (pin_index * 4))) == 0) { // MODE bits = Input mode
+ gpio->CRL |= (0x08 << (pin_index * 4)); // Set pull-up / pull-down
+ }
+ } else {
+ if ((gpio->CRH & (0x03 << ((pin_index % 8) * 4))) == 0) { // MODE bits = Input mode
+ gpio->CRH |= (0x08 << ((pin_index % 8) * 4)); // Set pull-up / pull-down
+ }
+ }
+ break;
+ case OpenDrain:
+ // Set open-drain for Output mode (General Purpose or Alternate Function)
+ if (pin_index < 8) {
+ if ((gpio->CRL & (0x03 << (pin_index * 4))) > 0) { // MODE bits = Output mode
+ gpio->CRL |= (0x04 << (pin_index * 4)); // Set open-drain
+ }
+ } else {
+ if ((gpio->CRH & (0x03 << ((pin_index % 8) * 4))) > 0) { // MODE bits = Output mode
+ gpio->CRH |= (0x04 << ((pin_index % 8) * 4)); // Set open-drain
+ }
+ }
+ break;
+ default:
+ break;
+ }
+}