kumar singh
BLE Transmitter not working
Fork of
Dealer_23Feb
by 
kumar singh
Diff: Beacon.cpp
- Revision:
- 25:0ac2680d594c
- Parent:
- 22:c2f034a13108
diff -r 1063cfc311e5 -r 0ac2680d594c Beacon.cpp
--- a/Beacon.cpp Thu Feb 23 13:21:08 2017 +0000
+++ b/Beacon.cpp Fri Mar 03 08:48:39 2017 +0000
@@ -35,11 +35,7 @@
-------------------------------------------------------------------------------------------------------------------
*/
-unsigned char SET_UUID[21] = {0x41,0x54,0xFF,0xF1,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0D};
-unsigned char SET_VIRTUAL_PACKET_UUID[23] = {0x01,0x01,0x41,0x54,0x01,0x01,0x02,0x01,0x02,0x03,0x04,0x05,0x06,0x07,0x08,0x09,0x03,0x0B,0x0C,0x05,0x0E,0x0F,0x0D};
-unsigned char SET_VIRTUAL_PACKET_UUID1[23] = {0x41,0x54,0xFF,0xF1,0x02,0x01,0x02,0x03,0x04,0x05,0x06,0x07,0x08,0x09,0x02,0x0B,0x0C,0x05,0x0E,0x0F,0x0D};
-unsigned char SET_VIRTUAL_PACKET_UUID2[23] = {0x12,0x21,0x41,0x54,0xFF,0xF1,0x0F,0x0E,0x0D,0x0C,0x0B,0x0A,0x09,0x08,0x07,0x06,0x05,0x04,0x03,0x02,0x01,0x00,0x0D};
-unsigned char SET_VIRTUAL_PACKET_UUID3[23] = {0x41,0x54,0xFF,0xF1,0x0F,0x0E,0x0D,0x0C,0x0B,0x04,0x05,0x08,0x07,0x06,0x05,0x04,0x03,0x02,0x01,0x00,0x0D};
+unsigned char SET_UUID[23] = {0x01,0x01,0x41,0x54,0xFF,0xF1,0xFD,0xA5,0x06,0x93,0xA4,0xE2,0x4F,0xB1,0xAF,0xCF,0xC6,0xEB,0x07,0x54,0x87,0x02,0x0D};
unsigned char SET_MAJOR[7] = {0x41,0x54,0xFF,0xF2,0x00,0x00,0x0D};
unsigned char SET_MINOR[7] = {0x41,0x54,0xFF,0xF3,0x00,0x00,0x0D};
unsigned char SET_MEASURED_POWER[6] = {0x41,0x54,0xFF,0xF4,0x00,0x0D};
@@ -47,14 +43,11 @@
unsigned char SET_PAIRING_PASSWORD[13] = {0x41,0x54,0xFF,0xF6,0x4F,0x42,0x44,0x21,0x30,0x30,0x30,0x31,0x0D};//Set Password here, Now set as OBD!1234
unsigned char SET_BROADCAST_INTERVAL[6] = {0x41,0x54,0xFF,0xF7,0x00,0x0D};
unsigned char SET_IBEACON_NAME[17] = {0x41,0x54,0xFF,0xF9,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0D};
-unsigned char SOFT_REBOOT[13] = {0x41,0x54,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0D};
+unsigned char SOFT_REBOOT[13] = {0x41,0x54,0xFF,0xFF,0x6D,0x69,0x6E,0x65,0x77,0x31,0x32,0x33,0x0D};
unsigned char SET_OPEN_BEACON[7] = {0x41,0x54,0x6F,0x70,0x65,0x6E,0x0D};
unsigned char SET_CLOSE_BEACON[8] = {0x41,0x54,0x63,0x6C,0x6F,0x73,0x65,0x0D};
unsigned char READ_BEACON_MAC_ID[6] = {0x52,0x44,0x6D,0x61,0x63,0x0D};
-unsigned char SOFT_REBOOT1[15] = {0x01,0x0B,0x41,0x54,0xFF,0xFF,0x6D,0x69,0x6E,0x65,0x77,0x31,0x32,0x33,0x0D};
-unsigned char SOFT_REBOOT2[15] = {0x41,0x54,0xFF,0xFF,0x6D,0x69,0x6E,0x65,0x77,0x31,0x32,0x33,0x0D};
-
void Process_Beacon_Command_Received(unsigned char* Command_Received);
void Change_Beacon_Parameter(unsigned char* Beacon_Parameter_To_Set);
void Get_Beacon_Response(void);
@@ -64,65 +57,49 @@
void Process_Beacon_Command_Received(unsigned char* Command_Received)
{
static unsigned char Temp_Pos,Start_Position,End_Position,Data_Length;
+ static unsigned char Beacon_Data[25],j;
+ static unsigned char Seq_No;
Start_Position = 0x02;
Temp_Pos = 0x02;
if((Command_Received[0] == SET_BEACON_UUID_CMD0) && (Command_Received[1] == SET_BEACON_UUID_CMD1)) //Check if command is receievd for setting UUID
{
- //DEBUG_UART2.printf("Setting UUID");
- Data_Length = 16;
+ DEBUG_UART2.printf("Setting UUID");
+ Data_Length = 21;
End_Position = (Start_Position + Data_Length);
- for(;Start_Position < End_Position;Start_Position++)
+ for(j=0;Start_Position < End_Position;Start_Position++)
{
- SET_UUID[Start_Position] = Command_Received[Temp_Pos++];
- //DEBUG_UART2.putc(SET_UUID[Start_Position]);
- //DEBUG_UART2.printf("%s",SET_UUID);
-
-
+ Beacon_Data[j++] = Command_Received[Start_Position];
}
- DEBUG_UART2.printf("UUID Set");
- Change_Beacon_Parameter(SET_VIRTUAL_PACKET_UUID1);
- }
- else if((Command_Received[0] == 0x12) && (Command_Received[1] == 0x21)) //Check if command is receievd for setting UUID
- {
- DEBUG_UART2.printf("Setting UUID2");
- Data_Length = 16;
- End_Position = (Start_Position + Data_Length);
- for(;Start_Position < End_Position;Start_Position++)
- {
- SET_UUID[Start_Position] = Command_Received[Temp_Pos++];
- //DEBUG_UART2.putc(SET_UUID[Start_Position]);
- //DEBUG_UART2.printf("%s",SET_UUID);
-
-
- }
- DEBUG_UART2.printf("UUID2 Set");
- Change_Beacon_Parameter(SET_VIRTUAL_PACKET_UUID3);
+ Beacon_Data[4] = Seq_No++;
+ Change_Beacon_Parameter(Beacon_Data,Data_Length);
+ wait(.5);
+ Change_Beacon_Parameter(SOFT_REBOOT,13);
}
else if((Command_Received[0] == SET_SET_MAJOR_CMD0) && (Command_Received[1] == SET_SET_MAJOR_CMD1)) //Check if command is received for Setting Major
{
SET_MAJOR[Start_Position++] = Command_Received[Temp_Pos++]; //MSB
SET_MAJOR[Start_Position] = Command_Received[Temp_Pos]; //LSB
DEBUG_UART2.printf("%s",SET_MAJOR);
- Change_Beacon_Parameter(SET_MAJOR);
+ //Change_Beacon_Parameter(SET_MAJOR);
}
else if((Command_Received[0] == SET_SET_MINOR_CMD0) && (Command_Received[1] == SET_SET_MINOR_CMD1)) //Check if command is received for Setting Minor
{
SET_MINOR[Start_Position++] = Command_Received[Temp_Pos++]; //MSB
SET_MINOR[Start_Position] = Command_Received[Temp_Pos]; //LSB
DEBUG_UART2.printf("%s",SET_MINOR);
- Change_Beacon_Parameter(SET_MINOR);
+ //Change_Beacon_Parameter(SET_MINOR);
}
else if((Command_Received[0] == SET_SET_MEASURED_POWER_CMD0) && (Command_Received[1] == SET_SET_MEASURED_POWER_CMD1)) //Check if command is received for Setting Measured power
{
SET_MEASURED_POWER[Start_Position] = Command_Received[Temp_Pos];
DEBUG_UART2.printf("%s",SET_MEASURED_POWER);
- Change_Beacon_Parameter(SET_MEASURED_POWER);
+ //Change_Beacon_Parameter(SET_MEASURED_POWER);
}
else if((Command_Received[0] == SET_TRANSMISSION_POWER_CMD0) && (Command_Received[1] == SET_TRANSMISSION_POWER_CMD1)) //Check if command is received for settting Transmission power
{
SET_TRANSMISSION_POWER[Start_Position] = Command_Received[Temp_Pos];
DEBUG_UART2.printf("%s",SET_TRANSMISSION_POWER);
- Change_Beacon_Parameter(SET_TRANSMISSION_POWER);
+ //Change_Beacon_Parameter(SET_TRANSMISSION_POWER);
}
else if((Command_Received[0] == SET_PAIRING_PASSWORD_CMD0) && (Command_Received[1] == SET_PAIRING_PASSWORD_CMD1)) //Check if command is received for Changing Pairing Password
{
@@ -143,7 +120,7 @@
{
SET_BROADCAST_INTERVAL[Start_Position] = Command_Received[Temp_Pos];
DEBUG_UART2.printf("%s",SET_BROADCAST_INTERVAL);
- Change_Beacon_Parameter(SET_BROADCAST_INTERVAL);
+ //Change_Beacon_Parameter(SET_BROADCAST_INTERVAL);
}
else if((Command_Received[0] == SET_IBEACON_NAME_CMD0) && (Command_Received[1] == SET_IBEACON_NAME_CMD1)) //Check if command is received for setting ibeacon name
{
@@ -152,38 +129,28 @@
for(;Start_Position < End_Position;Start_Position++)
SET_IBEACON_NAME[Start_Position] = Command_Received[Temp_Pos++];
DEBUG_UART2.printf("%s",SET_IBEACON_NAME);
- Change_Beacon_Parameter(SET_IBEACON_NAME);
+ //Change_Beacon_Parameter(SET_IBEACON_NAME);
}
else if((Command_Received[0] == SET_START_BEACON_CMD0) && (Command_Received[1] == SET_START_BEACON_CMD0)) //check if command is receievd for starting Beacon
{
DEBUG_UART2.printf("%s",SET_OPEN_BEACON);
- Change_Beacon_Parameter(SET_OPEN_BEACON);
+ //Change_Beacon_Parameter(SET_OPEN_BEACON);
}
else if((Command_Received[0] == SET_STOP_BEACON_CMD0) && (Command_Received[1] == SET_STOP_BEACON_CMD1)) //Check if command is received for Stopping beacon and go to sleep mode
{
DEBUG_UART2.printf("%s",SET_CLOSE_BEACON);
- Change_Beacon_Parameter(SET_CLOSE_BEACON);
+ //Change_Beacon_Parameter(SET_CLOSE_BEACON);
}
- else if((Command_Received[0] == SET_SOFT_REBOOT_CMD0) && (Command_Received[1] == SET_SOFT_REBOOT_CMD1)) //Check if command is received for Stopping beacon and go to sleep mode
- {
- Beacon_Module_UART.printf("%s",SOFT_REBOOT2); //Soft Reboot Beacon Module
- DEBUG_UART2.printf("Beacon Device Resetted %s",SOFT_REBOOT2);
- }
}
-void Change_Beacon_Parameter(unsigned char* Beacon_Parameter_To_Set)
+void Change_Beacon_Parameter(unsigned char* Beacon_Parameter_To_Set,unsigned char Length)
{
uint8 i;
- for(i = 0;i<21;i++)
+ for(i = 0;i<Length;i++)
{
Beacon_Module_UART.putc(Beacon_Parameter_To_Set[i]);
- DEBUG_UART2.putc(Beacon_Parameter_To_Set[i]);
+ DEBUG_UART2.printf("%2x",Beacon_Parameter_To_Set[i]);
}
- //Beacon_Module_UART.printf('%x',0x0d);
- //DEBUG_UART2.putc('%x',0x0d);
- Beacon_Module_UART.printf("%s",Beacon_Parameter_To_Set);
- //Beacon_Module_UART.printf("%s",SOFT_REBOOT); //Every Ibeacon command must be followed by Soft reset command in order to make the changes take place instantly
- //DEBUG_UART2.printf("%s",Beacon_Parameter_To_Set);
}
void Initialize_Beacon_Module(void)