Diff: main.cpp

Revision:

5:72944fa033f9

Parent:

4:36e214ebfa56

--- a/main.cpp	Wed Sep 30 19:49:02 2015 +0000
+++ b/main.cpp	Fri Jun 10 00:07:31 2016 +0000
@@ -1,102 +1,316 @@
 #include "mbed.h"
 #include "mDot.h"
 #include "MTSLog.h"
+#include "MTSSerial.h"
 #include <string>
 #include <vector>
 #include <algorithm>
+#include <sstream>
+#include <iomanip>
+//#include "PulseCounter.h"
 
 // these options must match the settings on your Conduit
 // uncomment the following lines and edit their values to match your configuration
-//static std::string config_network_name = "<lora network id>";
-//static std::string config_network_pass = "<lora network key>";
-//static uint8_t config_frequency_sub_band = 1;
+static std::string config_network_name = "campbellsci";
+static std::string config_network_pass = "campbellsci";
+static uint8_t config_frequency_sub_band = 1;
+
+InterruptIn pulseInterrupt(PB_1);
+DigitalOut greenLed(PA_11); // To turn the join LED on/off
+
+
+int pulseCount;
+void highPulseDetected() {
+    pulseCount++;
+}
+
+std::string VectorInt8_To_StrHex (const vector<uint8_t>& v)
+{
+    stringstream ss;
+    ss << std::hex << std::setfill('0');
+    vector<uint8_t>::const_iterator it;
+
+    for (it = v.begin(); it != v.end(); it++) {
+        ss << ":" << std::setw(2) << static_cast<unsigned>(*it);
+    }
+    return ss.str();
+}
 
-int main() {
+std::string VectorInt32_To_StrDec (const vector<uint32_t>& v)
+{
+    // Serial output for debugging
+    //mts::MTSSerial serial(XBEE_DOUT, XBEE_DIN, 512, 512);
+    //serial.baud(115200);
+    //mts::MTSSerial& _serial(serial);
+    stringstream ss;
+    // Body
+    ss << std::dec << std::setfill('0');
+    vector<uint32_t>::const_iterator it;
+
+    for (it = v.begin(); it != v.end(); it++) {
+        ss << ":" << std::setw(3) << static_cast<unsigned>(*it);
+        //_serial.writef(static_cast<unsigned>(*it));
+    }
+    return ss.str();
+}
+
+std::string VectorMdotFile_To_List (const vector<mDot::mdot_file>& v)
+{
+    // Serial output for debugging
+    mts::MTSSerial serial(XBEE_DOUT, XBEE_DIN, 512, 512);
+    serial.baud(115200);
+    mts::MTSSerial& _serial(serial);
+
+    stringstream ss;
+    vector<mDot::mdot_file>::const_iterator it;
+
+    _serial.writef(" DEBUG: Vector size for user files list %d\r\n" , v.size());
+
+    for (it = v.begin(); it != v.end(); it++) {
+        ss << (*it).name << " " ;
+    }
+    return ss.str();
+}
+
+int main()
+{
+    greenLed = 0;
+
+    //PulseCounter* pulseCount;
+    //PulseCounter(PinName pin, PinMode pull, int step,  uint32_t minwidth, uint32_t maxwidth,bool up, char c)
+    //PulseCounter* pulseCount = new PulseCounter(PB_1, PullNone, 1,  100, 1000, 0, 'C');
+
     int32_t ret;
     mDot* dot;
     std::vector<uint8_t> data;
-    std::string data_str = "hello!";
-    
+    //std::string data_str = "hello!";
+    AnalogIn in(PB_1);
+    std::ostringstream ss;
+    std::string data_str = "Hello";
+    //ss << in.read_u16();
+    //data_str = ss.str();
+
     // get a mDot handle
     dot = mDot::getInstance();
-    
+
+    // This section is to enable the debuging info over serial (rs232)
+    mts::MTSSerial serial(XBEE_DOUT, XBEE_DIN, 512, 512);
+    serial.baud(115200);
+    mts::MTSSerial& _serial(serial);
+    // Hello world
+    _serial.writef("\r\n\r\n\r\n\r\n");
+    _serial.writef("+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ \r\n");
+    _serial.writef("+                          Hello mDot                                         + \r\n");
+    _serial.writef("+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ \r\n");
+
+
+
     // print library version information
-    logInfo("version: %s", dot->getId().c_str());
+    _serial.writef("INFO: version: %s\r\n", dot->getId().c_str());
 
     //*******************************************
     // configuration
     //*******************************************
     // reset to default config so we know what state we're in
     dot->resetConfig();
-    
+
     dot->setLogLevel(mts::MTSLog::INFO_LEVEL);
 
     // set up the mDot with our network information: frequency sub band, network name, and network password
     // these can all be saved in NVM so they don't need to be set every time - see mDot::saveConfig()
-    
+
     // frequency sub band is only applicable in the 915 (US) frequency band
     // if using a MultiTech Conduit gateway, use the same sub band as your Conduit (1-8) - the mDot will use the 8 channels in that sub band
     // if using a gateway that supports all 64 channels, use sub band 0 - the mDot will use all 64 channels
-    logInfo("setting frequency sub band");
+    _serial.writef("INFO: setting frequency sub band: %d\r\n", config_frequency_sub_band);
     if ((ret = dot->setFrequencySubBand(config_frequency_sub_band)) != mDot::MDOT_OK) {
-        logError("failed to set frequency sub band %d:%s", ret, mDot::getReturnCodeString(ret).c_str());
+        _serial.writef("ERROR: failed to set frequency sub band %d:%s\r\n", ret, mDot::getReturnCodeString(ret).c_str());
+    }
+
+/* Dont' need network name when setting it network EUI
+    _serial.writef("INFO: setting network name: %s\r\n", config_network_name.c_str());
+    if ((ret = dot->setNetworkName(config_network_name)) != mDot::MDOT_OK) {
+        _serial.writef("ERROR: failed to set network name %d:%s\r\n", ret, mDot::getReturnCodeString(ret).c_str());
+    }
+*/           
+    // Initializing a vecotr in C++
+    // This compiler doesn't accept -> static std::vector<uint8_t> config_network_key {00,00,00,00,00,00,00,01};
+    static std::uint8_t netId[8] = {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01};
+    static std::vector<uint8_t> netIdV(&netId[0], &netId[0] + 8); // It is +8 since 8 members. You need start and end of the array.
+    _serial.writef("INFO: setting network ID (EUI): %s\r\n", VectorInt8_To_StrHex(netIdV));
+    if ((ret = dot->setNetworkId(netIdV)) != mDot::MDOT_OK) {
+        _serial.writef("ERROR: failed to set network ID %d:%s\r\n", ret, mDot::getReturnCodeString(ret).c_str());
+    }
+/*
+    _serial.writef("INFO: setting network password: %s\r\n", config_network_pass.c_str());
+    if ((ret = dot->setNetworkPassphrase(config_network_pass)) != mDot::MDOT_OK) {
+        _serial.writef("ERROR: failed to set network password %d:%s\r\n", ret, mDot::getReturnCodeString(ret).c_str());
+    }
+*/
+    // Initializing a vecotr in C++
+    static std::uint8_t netKey[16] = {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01};
+    static std::vector<uint8_t> netKeyV(&netKey[0], &netKey[0] + 16); // It is +16 since 16 members. You need start and end of the array.
+    _serial.writef("INFO: setting network key: %s\r\n", VectorInt8_To_StrHex(netKeyV));
+    if ((ret = dot->setNetworkKey(netKeyV)) != mDot::MDOT_OK) {
+        _serial.writef("ERROR: failed to set network key %d:%s\r\n", ret, mDot::getReturnCodeString(ret).c_str());
     }
     
-    logInfo("setting network name");
-    if ((ret = dot->setNetworkName(config_network_name)) != mDot::MDOT_OK) {
-        logError("failed to set network name %d:%s", ret, mDot::getReturnCodeString(ret).c_str());
-    }
-    
-    logInfo("setting network password");
-    if ((ret = dot->setNetworkPassphrase(config_network_pass)) != mDot::MDOT_OK) {
-        logError("failed to set network password %d:%s", ret, mDot::getReturnCodeString(ret).c_str());
-    }
-    
+    bool adrStatus = false;
+    _serial.writef("ADR Status is  %d\r\n", (*dot).getAdr());
+   _serial.writef("INFO: setting Adr %d: \r\n", adrStatus);
+    if ((ret = dot->setAdr(adrStatus)) != mDot::MDOT_OK) {
+        _serial.writef("ERROR: failed to set ADR %d:%s\r\n", ret, mDot::getReturnCodeString(ret).c_str());
+    } else
+    {
+        _serial.writef("Data Rate: %d\r\n", (*dot).getTxDataRate());        
+        _serial.writef("ADR Status is %d\r\n", (*dot).getAdr());
+
+        }
+        
+    /*
     // a higher spreading factor allows for longer range but lower throughput
     // in the 915 (US) frequency band, spreading factors 7 - 10 are available
     // in the 868 (EU) frequency band, spreading factors 7 - 12 are available
-    logInfo("setting TX spreading factor");
-    if ((ret = dot->setTxDataRate(mDot::SF_10)) != mDot::MDOT_OK) {
-        logError("failed to set TX datarate %d:%s", ret, mDot::getReturnCodeString(ret).c_str());
+    _serial.writef("INFO: setting TX data rate: ");
+    if ((ret = dot->setTxDataRate(mDot::DR2)) != mDot::MDOT_OK) {
+        _serial.writef("ERROR: failed to set TX datarate %d:%s\r\n", ret, mDot::getReturnCodeString(ret).c_str());
+    } else
+        _serial.writef("%d\r\n", (*dot).getTxDataRate());
+        
+    */
+
+
+    // request receive confirmation of packets from the gateway
+    _serial.writef("INFO: enabling ACKs\r\n");
+    if ((ret = dot->setAck(1)) != mDot::MDOT_OK) {
+        _serial.writef("ERROR: failed to enable ACKs %d:%s\r\n", ret, mDot::getReturnCodeString(ret).c_str());
+    }
+
+    // Public Network Mode
+    _serial.writef("INFO: Public network state:  %d\r\n", (*dot).getPublicNetwork());
+    _serial.writef("INFO: enabling Public network mode\r\n");
+    if ((ret = dot->setPublicNetwork(1)) != mDot::MDOT_OK) {
+        _serial.writef("ERROR: failed to enable Public Mode %d:%s\r\n", ret, mDot::getReturnCodeString(ret).c_str());
+    }
+    _serial.writef("INFO: Public network state:  %d\r\n", (*dot).getPublicNetwork());
+
+
+    _serial.writef("INFO: frequency band:  %s\r\n", mDot::FrequencyBandStr((*dot).getFrequencyBand()).c_str());
+    _serial.writef("INFO: frequency band:  %d\r\n", (*dot).getFrequencyBand());
+
+
+    const uint8_t _freqBand = 2;
+    _serial.writef("INFO: Setting frequency band to:  %s\r\n", mDot::FrequencyBandStr(_freqBand).c_str());
+    if ((ret = dot->setFrequencyBand(_freqBand)) != mDot::MDOT_OK) {
+        _serial.writef("ERROR: failed to enable Public Mode %d:%s\r\n", ret, mDot::getReturnCodeString(ret).c_str());
+    }
+
+    // Workaround to lock the TX frequencies to a single Aussie one while working with the incorrect library.
+    // The latest library has the fixed 8 Aussie libraries and it makes the following  lines irrelevent.
+    //_serial.writef("INFO: Setting TX frequency to:  %s\r\n", mDot::FrequencyBandStr(_freqBand).c_str());
+    //if ((ret = dot->setTxFrequency(915200000)) != mDot::MDOT_OK) {
+    //    _serial.writef("ERROR: failed to Set TX frequency %d:%s\r\n", ret, mDot::getReturnCodeString(ret).c_str());
+    //}
+    //_serial.writef("INFO: TX frequency:  %d\r\n", (*dot).getTxFrequency());
+
+
+    // save this configuration to the mDot's NVM
+    _serial.writef("INFO: saving config\r\n");
+    if (! dot->saveConfig()) {
+        _serial.writef("ERROR: failed to save configuration\r\n");
     }
     
-    // request receive confirmation of packets from the gateway
-    logInfo("enabling ACKs");
-    if ((ret = dot->setAck(1)) != mDot::MDOT_OK) {
-        logError("failed to enable ACKs %d:%s", ret, mDot::getReturnCodeString(ret).c_str());
-    }
-    
-    // save this configuration to the mDot's NVM
-    logInfo("saving config");
-    if (! dot->saveConfig()) {
-        logError("failed to save configuration");
-    }
     //*******************************************
     // end of configuration
     //*******************************************
 
-    // attempt to join the network
-    logInfo("joining network");
-    while ((ret = dot->joinNetwork()) != mDot::MDOT_OK) {
-        logError("failed to join network %d:%s", ret, mDot::getReturnCodeString(ret).c_str());
+    _serial.writef("INFO: frequency band:  %s\r\n", mDot::FrequencyBandStr((*dot).getFrequencyBand()).c_str());
+
+    _serial.writef("INFO: Device ID%s\r\n", VectorInt8_To_StrHex((*dot).getDeviceId()).c_str());
+
+    _serial.writef("INFO: Network  ID%s\r\n", VectorInt8_To_StrHex((*dot).getNetworkId()).c_str());
+    _serial.writef("INFO: Network Key%s\r\n", VectorInt8_To_StrHex((*dot).getNetworkKey()).c_str());
+
+    _serial.writef("INFO: Join mode:  %s\r\n",      mDot::JoinModeStr((*dot).getJoinMode()).c_str());
+
+    _serial.writef("INFO: List of channel frequencies currently in use%s\r\n", VectorInt32_To_StrDec((*dot).getChannels()).c_str());
+    // TODO: These data rate lists don't make sense.
+    _serial.writef("INFO: List of channel datarate ranges currently in use%s\r\n", VectorInt8_To_StrHex((*dot).getChannelRanges()).c_str());
+    //_serial.writef("INFO: List of channel frequencies in config file to be used as session defaults%s\r\n", VectorInt32_To_StrDec((*dot).getConfigChannels()));
+    //_serial.writef("INFO: List of channel frequencies currently in use%s\r\n", VectorInt32_To_StrDec((*dot).getChannels()));
+
+
+
+//_serial.writef("INFO: List user files stored in flash%s\r\n", VectorMdotFile_To_List((*dot).listUserFiles()));
+
+
+//*******************************************
+// end of debuging info
+//*******************************************
+    
+    pulseCount=0;  
+    pulseInterrupt.rise(&highPulseDetected);
+    
+// attempt to join the network
+    _serial.writef("INFO: joining network...\r\n");
+    while ((ret = dot->joinNetworkOnce()) != mDot::MDOT_OK) {
+        _serial.writef("ERROR: failed to join network %d:%s\r\n", ret, mDot::getReturnCodeString(ret).c_str());
         // in the 868 (EU) frequency band, we need to wait until another channel is available before transmitting again
         osDelay(std::max((uint32_t)1000, (uint32_t)dot->getNextTxMs()));
     }
+    greenLed = 1; // Joined Successfuly 
 
-    // format data for sending to the gateway
-    for (std::string::iterator it = data_str.begin(); it != data_str.end(); it++)
-        data.push_back((uint8_t) *it);
+    mDot::rssi_stats _rssiStats;
+    
+    //pulseCount->startpulse();
+    while (true) {
 
-    while (true) {
+        //format data for sending to the gateway
+        for (std::string::iterator it = data_str.begin(); it != data_str.end(); it++) {
+            data.push_back((uint8_t) *it);
+        }
+
         // send the data to the gateway
         if ((ret = dot->send(data)) != mDot::MDOT_OK) {
-            logError("failed to send", ret, mDot::getReturnCodeString(ret).c_str());
+            _serial.writef("ERROR: failed to send\r\n", ret, mDot::getReturnCodeString(ret).c_str());
         } else {
-            logInfo("successfully sent data to gateway");
+            _serial.writef("INFO: successfully sent data to gateway ");
+
+            _rssiStats = dot->getRssiStats();
+            _serial.writef("+ RSSI values( last:%d min:%d max:%d avg:%d ) \r\n", _rssiStats.last, _rssiStats.min, _rssiStats.max, _rssiStats.avg);
         }
 
         // in the 868 (EU) frequency band, we need to wait until another channel is available before transmitting again
-        osDelay(std::max((uint32_t)5000, (uint32_t)dot->getNextTxMs()));
+        //osDelay(std::max((uint32_t)50, (uint32_t)dot->getNextTxMs()));
+        osDelay(std::max((uint32_t)2000, (uint32_t)dot->getNextTxMs()));
+
+        ss.str("");
+/*
+        //int temp = dht11->readTemperature();
+        int err = dht.readData();
+        if (err == 0) {
+            float temp = dht.ReadTemperature(CELCIUS);
+            float rh = dht.ReadHumidity();
+            //ss << (temp+1000);
+            ss << rh;
+            
+        }
+        else
+        {
+            ss.str("  :err ");
+            ss << err;
+        }
+*/
+        data.clear();
+        // Converting int to string in C++ using <sstream>
+        //ss << (_rssiStats.last);
+        //ss << (temp);
+        //ss << (in.read_u16());
+        
+        //int p = pulseCount->readall();
+        ss << pulseCount;
+        data_str = ss.str();
+        //wait(5);
     }
 
     return 0;