Example of reading and magnetometer sensor (HMC5883L)
Dependencies: MODSERIAL mbed-rtos mbed
Fork of ReadingMag_HMC5883L by
HMC5883L.cpp
- Committer:
- Maor_T
- Date:
- 2016-05-24
- Revision:
- 1:aea254b39529
- Parent:
- 0:6bc5f85ca6fa
File content as of revision 1:aea254b39529:
#include "HMC5883L.h" HMC5883L::HMC5883L(PinName sda, PinName scl): i2c(sda, scl) { //100KHz, as specified by the datasheet. char rx; i2c.frequency(100000); //Testar depois com 400KHz //========================================================================================================== // Read chip_id //========================================================================================================== rx = Read(HMC5883L_IDENT_A); if (rx != 0x48)//ID do chip printf("\ninvalid chip id %d\r\n", rx); //========================================================================================================== // Let's set the Configuration Register A //========================================================================================================== // This register set's the number of samples averaged per measurement output, the rate at which data is written // to all three data output registers and the measurement flow of the device. // ------------------------------------------------------- // |CRA7 CRA6 CRA5 CRA4 CRA3 CRA2 CRA1 CRA0 | // |(1) MA1(1) MA0(1) DO2(1) DO1(0) DO0(0) MS1(0) MS0(0)| -> This is the default value // ------------------------------------------------------- // CRA7 -> we have to clear this bit for correct operation (0) // CRA6 to CRA5 -> Let's select the maximum number of samples averaged per measurement output (11) // CRA4 to CRA2 -> Also let's select the maximum data output rate (110) // CRA1 to CRA0 -> The measurement flow is defined to normal (00) // ------------------------------------------------------- // |CRA7 CRA6 CRA5 CRA4 CRA3 CRA2 CRA1 CRA0 | // |(0) MA1(1) MA0(1) DO2(1) DO1(1) DO0(0) MS1(0) MS0(0)| -> This is the new value, 0x78 in hex // ------------------------------------------------------- //Write(HMC5883L_CONFIG_A,0x78); //Write(HMC5883L_CONFIG_A,0x70); //========================================================================================================== // The Configuration Register B is set to 0010 0000 by default, this is a +/- 1.3 Ga sensor field range and // the gain of LSB/gauss is 1090. This is the maximum value, so let's leave it like that. //========================================================================================================== //Datasheet page 13. I will explain later //Write(HMC5883L_CONFIG_B,0x20); //Write(HMC5883L_CONFIG_B,0xA0); //========================================================================================================== // Let's set the Mode Register //========================================================================================================== // This register set's the operation mode, from continuous-measurements mode, single-measurement mode and idle mode. // We will set to Continuouse-measurement mode, so the device continuously performs measurements and places the // result in the data register // --------------------------------------------- // |MR7 MR6 MR5 MR4 MR3 MR2 MR1 MR0 | -> This is the new value, 0x78 in hex, we are going to change // |(1) (0) (0) (0) (0) (0) MD1(0) MD0(1)| the MD1 and MD0 to 00 and clear the MR7 for correct operation. // --------------------------------------------- The final value is 0000 0000 (0x00). Write(HMC5883L_MODE,0x00); } void HMC5883L::Write(char reg_address, char data) { char tx[2]; tx[0]=reg_address; tx[1]=data; i2c.write(HMC5883L_I2C_WRITE,tx,2); } char HMC5883L::Read(char data) { char tx = data; char rx; i2c.write(HMC5883L_I2C_WRITE, &tx, 1); i2c.read(HMC5883L_I2C_READ, &rx, 1); return rx; } void HMC5883L::MultiByteRead(char address, char* output, int size) { i2c.write(HMC5883L_I2C_WRITE, &address, 1); //tell it where to read from i2c.read(HMC5883L_I2C_READ, output, size); //tell it where to store the data read } float HMC5883L::getMx() { //return (x * m_Scale); char lsb_byte = 0; signed short msb_byte; lsb_byte = Read(HMC5883L_X_MSB); msb_byte = lsb_byte << 8; msb_byte |= Read(HMC5883L_X_LSB); return (float)msb_byte; /* char tx[1]; char rx[2]; tx[0]=HMC5883L_X_MSB; i2c.write(HMC5883L_I2C_READ,tx,1); i2c.read(HMC5883L_I2C_READ,rx,2); return ((int)rx[0]<<8|(int)rx[1]); */ } float HMC5883L::getMy() { //return (y * m_Scale); char lsb_byte = 0; signed short msb_byte; lsb_byte = Read(HMC5883L_Y_MSB); msb_byte = lsb_byte << 8; msb_byte |= Read(HMC5883L_Y_LSB); return (float)msb_byte; } float HMC5883L::getMz() { //return (z * m_Scale); char lsb_byte = 0; signed short msb_byte; lsb_byte = Read(HMC5883L_Z_MSB); msb_byte = lsb_byte << 8; msb_byte |= Read(HMC5883L_Z_LSB); return (float)msb_byte; }