Sungwoo Kim
distribution-201229
main.cpp
- Committer:
- Lightvalve
- Date:
- 2020-10-08
- Revision:
- 145:35f5ec0d7e56
- Parent:
- 144:fb8c3025963c
File content as of revision 145:35f5ec0d7e56:
//201008-7
#include "mbed.h"
#include "FastPWM.h"
#include "INIT_HW.h"
#include "function_CAN.h"
#include "SPI_EEP_ENC.h"
#include "I2C_AS5510.h"
#include "setting.h"
#include "function_utilities.h"
#include "stm32f4xx_flash.h"
#include "FlashWriter.h"
using namespace std;
Timer t;
///191008////
// dac & check ///////////////////////////////////////////
DigitalOut check(PC_2);
DigitalOut check_2(PC_3);
AnalogOut dac_1(PA_4);
AnalogOut dac_2(PA_5);
AnalogIn adc1(PC_4); //pressure_1
AnalogIn adc2(PB_0); //pressure_2
AnalogIn adc3(PC_1); //current
// PWM ///////////////////////////////////////////
float dtc_v=0.0f;
float dtc_w=0.0f;
// I2C ///////////////////////////////////////////
I2C i2c(PC_9,PA_8); // SDA, SCL (for K22F)
const int i2c_slave_addr1 = 0x56;
unsigned int value; // 10bit output of reading sensor AS5510
// SPI ///////////////////////////////////////////
//SPI eeprom(PB_15, PB_14, PB_13); // EEPROM //(SPI_MOSI, SPI_MISO, SPI_SCK);
//DigitalOut eeprom_cs(PB_12);
//FlashWriter writer(6);//2부터 7까지 되는듯 아마 sector
SPI enc(PC_12,PC_11,PC_10);
DigitalOut enc_cs(PD_2);
DigitalOut LED(PA_15);
// UART ///////////////////////////////////////////
Serial pc(PA_9,PA_10); // _ UART
// CAN ///////////////////////////////////////////
CAN can(PB_8, PB_9, 1000000);
CANMessage msg;
void onMsgReceived()
{
CAN_RX_HANDLER();
}
// Variables ///////////////////////////////////////////
State pos;
State vel;
State Vout;
State torq;
State pres_A;
State pres_B;
State cur;
State valve_pos;
State INIT_Vout;
State INIT_Valve_Pos;
State INIT_Pos;
State INIT_torq;
extern int CID_RX_CMD;
extern int CID_RX_REF_POSITION;
extern int CID_RX_REF_VALVE_POS;
extern int CID_RX_REF_PWM;
extern int CID_TX_INFO;
extern int CID_TX_POSITION;
extern int CID_TX_TORQUE;
extern int CID_TX_PRES;
extern int CID_TX_VOUT;
extern int CID_TX_VALVE_POSITION;
// =============================================================================
// =============================================================================
// =============================================================================
/*******************************************************************************
* REFERENCE MODE
******************************************************************************/
enum _REFERENCE_MODE {
MODE_REF_NO_ACT = 0, //0
MODE_REF_DIRECT, //1
MODE_REF_COS_INC, //2
MODE_REF_LINE_INC, //3
MODE_REF_SIN_WAVE, //4
MODE_REF_SQUARE_WAVE, //5
};
/*******************************************************************************
* CONTROL MODE
******************************************************************************/
enum _CONTROL_MODE {
//control mode
MODE_NO_ACT = 0, //0
MODE_VALVE_POSITION_CONTROL, //1
MODE_JOINT_CONTROL, //2
MODE_VALVE_OPEN_LOOP, //3
MODE_JOINT_ADAPTIVE_BACKSTEPPING, //4
MODE_VALVE_POSITION_TORQUE_CONTROL_LEARNING, //5
MODE_JOINT_POSITION_PRES_CONTROL_PWM, //6
MODE_JOINT_POSITION_PRES_CONTROL_VALVE_POSITION, //7
MODE_VALVE_POSITION_PRES_CONTROL_LEARNING, //8
MODE_TEST_CURRENT_CONTROL, //9
MODE_TEST_PWM_CONTROL, //10
MODE_CURRENT_CONTROL, //11
MODE_JOINT_POSITION_TORQUE_CONTROL_CURRENT, //12
MODE_JOINT_POSITION_PRES_CONTROL_CURRENT, //13
//utility
MODE_TORQUE_SENSOR_NULLING = 20, //20
MODE_VALVE_NULLING_AND_DEADZONE_SETTING, //21
MODE_FIND_HOME, //22
MODE_VALVE_GAIN_SETTING, //23
MODE_PRESSURE_SENSOR_NULLING, //24
MODE_PRESSURE_SENSOR_CALIB, //25
MODE_ROTARY_FRICTION_TUNING, //26
MODE_DDV_POS_VS_PWM_ID = 30, //30
MODE_DDV_DEADZONE_AND_CENTER, //31
MODE_DDV_POS_VS_FLOWRATE, //32
MODE_SYSTEM_ID, //33
};
void SystemClock_Config(void)
{
RCC_OscInitTypeDef RCC_OscInitStruct = {0};
RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
/** Configure the main internal regulator output voltage
*/
__HAL_RCC_PWR_CLK_ENABLE();
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
/** Initializes the CPU, AHB and APB busses clocks
*/
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
RCC_OscInitStruct.PLL.PLLM = 8;//8
RCC_OscInitStruct.PLL.PLLN = 180; //180
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
RCC_OscInitStruct.PLL.PLLQ = 2;
RCC_OscInitStruct.PLL.PLLR = 2;
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
{
//Error_Handler();
}
/** Activate the Over-Drive mode
*/
if (HAL_PWREx_EnableOverDrive() != HAL_OK)
{
//Error_Handler();
}
/** Initializes the CPU, AHB and APB busses clocks
*/
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
{
//Error_Handler();
}
}
float u_past[num_array_u_past] = {0.0f};
float x_past[num_array_x_past] = {0.0f};
float x_future[num_array_x_future] = {0.0f};
float f_past[num_array_f_past] = {0.0f};
float f_future[num_array_f_future] = {0.0f};
float input_NN[num_input] = { 0.0f };
const float h1[num_input][16] = {
{-1.202144980430603f,1.138988971710205f,0.12903714179992676f,0.4784081280231476f,-2.007096529006958f,1.1101239919662476f,-0.17472904920578003f,1.376711368560791f,-0.6657677292823792f,-1.2683919668197632f,-0.2366894781589508f,-2.119908571243286f,-0.27179795503616333f,-0.2513915002346039f,-0.2571594715118408f,-2.217491626739502f},
{-1.038386583328247f,0.9783099293708801f,-0.3927857577800751f,0.1331273317337036f,-1.6192518472671509f,0.7398083209991455f,-0.4054011106491089f,0.999164342880249f,-0.3204660713672638f,-0.7893865704536438f,-0.2734762132167816f,-1.7904084920883179f,0.22786423563957214f,-0.6183355450630188f,-0.20967772603034973f,-1.7576642036437988f},
{-0.8073722124099731f,0.723030686378479f,0.36391180753707886f,-0.25218313932418823f,-0.8648297190666199f,0.646933913230896f,0.2872133255004883f,0.9005036354064941f,-0.26115748286247253f,-0.5288271307945251f,-0.3473871052265167f,-1.568228840827942f,-0.010325154289603233f,0.032464317977428436f,0.05590221285820007f,-1.797452688217163f},
{-0.30040138959884644f,-0.03466230630874634f,0.39742106199264526f,0.37627866864204407f,-0.06165529042482376f,-0.24948622286319733f,-0.11584559082984924f,0.6195026636123657f,0.0672391802072525f,0.11928713321685791f,0.09644106775522232f,-0.6219649910926819f,-0.1723935604095459f,0.1230471059679985f,-0.2961459457874298f,-1.0144660472869873f},
{0.9413514733314514f,-0.9783564209938049f,-0.0051451027393341064f,0.2973308861255646f,1.2383958101272583f,-1.0510715246200562f,0.1294034719467163f,-0.8967423439025879f,0.22686034440994263f,1.0535863637924194f,0.3483673930168152f,0.28839874267578125f,-0.07595616579055786f,0.475301057100296f,-0.3865056037902832f,-0.2590292990207672f},
{2.2739834785461426f,-3.384673595428467f,0.21773302555084229f,0.2994205355644226f,3.3027589321136475f,-3.102123737335205f,0.16514194011688232f,-3.0555598735809326f,0.3947591781616211f,2.9011330604553223f,-0.2471718192100525f,2.413551092147827f,-0.27255699038505554f,0.875239372253418f,-0.4132833778858185f,1.5249680280685425f},
{-0.0025823377072811127f,0.5788406729698181f,-0.2501986622810364f,-0.6869844198226929f,0.013595464639365673f,0.958987295627594f,0.06014183163642883f,-0.6783658266067505f,0.2335476279258728f,-0.15955637395381927f,0.14809231460094452f,0.49601414799690247f,-0.17972350120544434f,-0.01836634986102581f,-0.15618428587913513f,1.9472782611846924f},
{-0.5333747863769531f,0.6159882545471191f,-0.26619744300842285f,-0.10663940757513046f,-0.6672677397727966f,0.7491434812545776f,-0.17925891280174255f,0.45909467339515686f,-0.061611875891685486f,-0.5273573398590088f,0.10323914140462875f,-0.1594064086675644f,0.3640030324459076f,0.04273512586951256f,0.04303058981895447f,0.4016958773136139f},
{-0.06486926227807999f,0.5101504325866699f,0.10248100757598877f,-0.6076595187187195f,-0.22489143908023834f,0.28914013504981995f,-0.07246989011764526f,-0.32467958331108093f,-0.3318542540073395f,0.43399131298065186f,-0.29930150508880615f,0.8827233910560608f,0.2215290069580078f,0.17675165832042694f,-0.30555272102355957f,1.0407618284225464f},
{0.0067978473380208015f,-0.538397490978241f,0.18462657928466797f,-0.3743363916873932f,0.18972061574459076f,-0.09740876406431198f,-0.2990540862083435f,-0.5601083636283875f,-0.039114855229854584f,0.16344060003757477f,-0.010178256779909134f,0.4692024886608124f,0.36460021138191223f,-0.18887411057949066f,0.3484981060028076f,1.2080103158950806f},
{0.5042862892150879f,-0.23018865287303925f,0.37182438373565674f,0.0031008694786578417f,-0.13351543247699738f,-0.37750890851020813f,-0.20339298248291016f,-0.5399224162101746f,-0.4469622075557709f,0.7113228440284729f,0.34657230973243713f,0.5766669511795044f,-0.07425376027822495f,0.058319900184869766f,0.26688337326049805f,0.7508887648582458f},
{-0.36814379692077637f,-0.5277806520462036f,-0.40320003032684326f,-0.26136666536331177f,-0.2674432694911957f,-0.26984360814094543f,0.1533789038658142f,0.007386255543678999f,-0.17324255406856537f,0.6930100321769714f,-0.41594198346138f,0.6991134881973267f,0.13697238266468048f,0.04665316268801689f,0.10493969917297363f,0.6447699666023254f},
{-0.10107079893350601f,-0.23446384072303772f,0.19847965240478516f,-0.11969888210296631f,-0.07624413073062897f,0.021741967648267746f,-0.2404318004846573f,-0.14804726839065552f,-0.20712880790233612f,0.17828989028930664f,-0.11077233403921127f,0.1089673861861229f,0.08429888635873795f,0.060614317655563354f,-0.22268100082874298f,0.13039818406105042f},
{-0.22510682046413422f,-0.12380469590425491f,0.4127817749977112f,-0.3654475212097168f,-0.4933675229549408f,-0.36989352107048035f,-0.32001304626464844f,-0.5990984439849854f,-0.17157448828220367f,0.11538881808519363f,-0.19669756293296814f,0.046649251133203506f,-0.32045069336891174f,-0.04418804123997688f,0.0479682981967926f,0.4848869740962982f},
{0.08632653206586838f,0.06087305769324303f,0.20282304286956787f,-0.21891111135482788f,0.13672329485416412f,-0.18774953484535217f,0.04202890396118164f,0.043800003826618195f,0.25277137756347656f,0.3155035078525543f,-0.2811494767665863f,-0.37795940041542053f,0.09589854627847672f,-0.07150355726480484f,0.0668090283870697f,0.3614422380924225f},
{-0.14654578268527985f,-0.3255223035812378f,-0.40439701080322266f,-0.3830048739910126f,-0.2781727612018585f,-0.08479150384664536f,-0.15568238496780396f,-0.3112363815307617f,0.14826036989688873f,0.26614072918891907f,-0.47562071681022644f,-0.1283193975687027f,-0.2787332534790039f,-0.02893819846212864f,-0.08245879411697388f,0.2619592249393463f},
{-0.1407018005847931f,-0.28579166531562805f,0.16706281900405884f,-0.21144752204418182f,-0.025171607732772827f,-0.4996216595172882f,-0.041414469480514526f,-0.4635230600833893f,-0.10190882533788681f,0.5193468332290649f,-0.3552822470664978f,0.2423761785030365f,0.10444391518831253f,0.3413086235523224f,0.29427415132522583f,-0.02577020600438118f},
};
const float h2[16][16] = {
{-0.42087849974632263f,0.4165714979171753f,-0.06966331601142883f,-0.40978044271469116f,-0.21907491981983185f,0.19977861642837524f,-0.09562018513679504f,0.0904630720615387f,-0.43008196353912354f,-0.1415480375289917f,-5.7234206199646f,-0.3770526647567749f,-2.265185832977295f,-1.3839008808135986f,-0.46374428272247314f,-0.3703479766845703f},
{0.10605034232139587f,-0.8491718769073486f,0.057057321071624756f,-0.11637905985116959f,-1.471933126449585f,-2.3849689960479736f,-0.678670346736908f,-0.4641587734222412f,-0.33757925033569336f,0.2895788848400116f,-3.7726151943206787f,-0.825717568397522f,-0.4287202060222626f,1.856231927871704f,-0.3886423408985138f,-0.8368627429008484f},
{-0.22745239734649658f,0.003037691116333008f,-0.061119019985198975f,0.35696902871131897f,0.05568113923072815f,0.011741191148757935f,-0.20225946605205536f,-0.08465918898582458f,0.3489862382411957f,0.0687277615070343f,0.31964078545570374f,0.3004753887653351f,0.36063823103904724f,-0.42892736196517944f,0.08652284741401672f,0.027493387460708618f},
{0.01821889728307724f,-0.19988501071929932f,-0.2894435524940491f,0.5687466859817505f,0.08946844935417175f,0.4089488089084625f,-0.23805393278598785f,0.4122363030910492f,0.26211628317832947f,0.2953031361103058f,0.1993970274925232f,0.28493621945381165f,-0.5520196557044983f,-0.30905404686927795f,0.2588307857513428f,0.06752173602581024f},
{-0.4842865467071533f,0.5623611807823181f,-0.25313520431518555f,-0.015972860157489777f,-2.685121536254883f,-0.8270378112792969f,-0.6444149613380432f,-0.27048569917678833f,-0.024399548768997192f,-0.39465832710266113f,-1.3381013870239258f,-0.9601086378097534f,-0.23603275418281555f,-7.192060947418213f,-0.6448869705200195f,-0.5070762038230896f},
{0.26964879035949707f,-0.20627757906913757f,-0.3519742488861084f,0.08445581048727036f,-0.5232159495353699f,-1.5471696853637695f,-0.7417458295822144f,-0.18649421632289886f,-0.23047015070915222f,0.3579089343547821f,-1.5071357488632202f,-0.45861613750457764f,-1.9862370491027832f,0.5577003955841064f,-0.024327976629137993f,-0.8124467134475708f},
{-0.1828227937221527f,-0.02554568648338318f,-0.3260969817638397f,0.08422836661338806f,-0.38453540205955505f,-0.25432005524635315f,0.285016268491745f,0.12387624382972717f,-0.0982072651386261f,0.13111665844917297f,-0.03692615032196045f,-0.32796353101730347f,-0.21546880900859833f,0.049302369356155396f,-0.27088475227355957f,-0.4124959409236908f},
{-0.0016780151054263115f,-0.17736129462718964f,0.33083590865135193f,-0.8090094327926636f,-2.097384214401245f,-2.0368118286132812f,-0.572920560836792f,-0.4613488018512726f,0.2600560486316681f,-0.37898191809654236f,-2.721445083618164f,-0.653968334197998f,-0.1349858194589615f,1.660499930381775f,-0.22006866335868835f,0.04596048220992088f},
{-0.31423863768577576f,0.341561883687973f,-0.11379697918891907f,-0.23742690682411194f,0.041274964809417725f,-0.35426101088523865f,-0.256329745054245f,0.0019084513187408447f,0.06103590130805969f,-0.38046833872795105f,-0.4106711745262146f,-0.4447551667690277f,-0.518744945526123f,-0.4609438180923462f,-0.48924964666366577f,-0.37356749176979065f},
{-0.6705074906349182f,0.2682148516178131f,-0.13502129912376404f,0.3107656240463257f,1.292205572128296f,0.2772318422794342f,-0.14059102535247803f,-0.5952746868133545f,-0.13619378209114075f,0.16938945651054382f,1.6001759767532349f,-0.28879669308662415f,0.11340539157390594f,-0.8598341345787048f,-0.3627699911594391f,-0.8332610130310059f},
{-0.2734835743904114f,-0.006139871198683977f,0.0457797646522522f,-0.3544529974460602f,-0.03321319818496704f,-0.43699121475219727f,0.17873415350914001f,-0.20421427488327026f,-0.050184011459350586f,0.12480869889259338f,-0.21864968538284302f,0.3545852601528168f,-0.3647043704986572f,0.4158240258693695f,-0.39413556456565857f,-0.280180960893631f},
{0.21503236889839172f,-0.006975529715418816f,0.3954955041408539f,-0.002965252147987485f,0.37924548983573914f,-4.352310657501221f,-0.5501192808151245f,-0.28764215111732483f,0.3487861454486847f,-0.32520344853401184f,-4.292383193969727f,-0.7163788676261902f,-1.6283358335494995f,-0.7420485615730286f,0.006725164595991373f,0.05786462873220444f},
{-0.2682988941669464f,-0.21874792873859406f,-0.15798500180244446f,0.3955790102481842f,-0.37393757700920105f,0.34758031368255615f,0.11292675137519836f,-0.2947862446308136f,-0.3764709532260895f,0.2424570620059967f,-0.11641307920217514f,-0.2837170362472534f,0.41839322447776794f,-0.010468282736837864f,-0.12172400951385498f,0.1040443703532219f},
{-0.4393233060836792f,0.42088809609413147f,-0.2018718123435974f,0.3200990855693817f,0.07545611262321472f,0.3041123151779175f,-0.4151543378829956f,-0.21416273713111877f,-0.24509364366531372f,0.19522181153297424f,0.2655569314956665f,-0.6807448267936707f,-0.15791945159435272f,-0.13821366429328918f,-0.524168848991394f,-0.4587186574935913f},
{0.4138670265674591f,0.1604653298854828f,0.056746453046798706f,0.036025404930114746f,0.3228367865085602f,-0.07083973288536072f,0.018455177545547485f,0.0059362053871154785f,0.40515169501304626f,0.014240056276321411f,-0.07738298177719116f,0.1407785713672638f,-0.13024571537971497f,-0.29546058177948f,-0.11976784467697144f,-0.35825538635253906f},
{-0.5081422328948975f,-0.06909644603729248f,0.12081471085548401f,-0.5307455062866211f,0.6937620639801025f,-1.7394471168518066f,-0.112851083278656f,0.14146126806735992f,-0.3893685042858124f,-0.02222958207130432f,-3.628293752670288f,-0.5519410967826843f,-1.8406803607940674f,-0.49850648641586304f,-0.041028495877981186f,-0.20542386174201965f},
};
const float h3[16][16] = {
{-0.36079341173171997f,-0.4983029067516327f,0.5477026700973511f,-0.3543650507926941f,-0.13606339693069458f,-0.08796219527721405f,0.3332441747188568f,0.3036012351512909f,-0.2405819296836853f,0.04891335964202881f,-0.11870327591896057f,-0.07875661551952362f,0.1948052942752838f,0.3429747223854065f,-0.7145496606826782f,0.30580008029937744f},
{0.047732532024383545f,0.44144171476364136f,-0.03628820925951004f,-0.28411877155303955f,-0.46656039357185364f,0.25812917947769165f,-0.3198729455471039f,0.06247803568840027f,0.18673597276210785f,-0.1780138611793518f,0.2920512855052948f,-0.27276602387428284f,-0.02848001755774021f,0.5977586507797241f,-0.2459808588027954f,-0.48939114809036255f},
{0.07903262972831726f,0.2790505588054657f,-0.07798504829406738f,0.04248586297035217f,-0.1963958442211151f,-0.19260792434215546f,-0.4038352966308594f,0.015906542539596558f,0.15353140234947205f,0.030178606510162354f,0.2488909661769867f,0.13805970549583435f,-0.0816211998462677f,-0.20733052492141724f,-0.3036302626132965f,0.054825395345687866f},
{-0.30922991037368774f,0.021412329748272896f,0.13412728905677795f,-0.3774894177913666f,-0.41859447956085205f,0.27175024151802063f,0.20021501183509827f,0.07002416253089905f,-0.28385472297668457f,-0.365601509809494f,0.13192829489707947f,0.41021624207496643f,-0.2204446941614151f,0.2754747271537781f,0.3391396701335907f,-0.3910892903804779f},
{-0.39607733488082886f,-0.21291382610797882f,1.3589930534362793f,0.022423356771469116f,0.6434191465377808f,-0.27518749237060547f,0.03828391432762146f,0.8088476061820984f,-0.08640444278717041f,-0.11053556203842163f,-0.10529157519340515f,-0.2748071551322937f,1.2419054508209229f,0.28642505407333374f,0.10066504031419754f,-0.34874701499938965f},
{-0.37449589371681213f,0.3277108669281006f,-1.8050578832626343f,-0.01751975156366825f,0.043049342930316925f,1.43709397315979f,-0.18732719123363495f,0.22384825348854065f,-0.7361441850662231f,-0.46488797664642334f,-0.21090413630008698f,-0.17663529515266418f,-0.20991544425487518f,0.9128029346466064f,0.5134555697441101f,-0.9794425964355469f},
{0.4110594093799591f,0.17092753946781158f,-0.2997543513774872f,0.2397543042898178f,0.10350155830383301f,-0.11353641003370285f,-0.08670487999916077f,-0.25336313247680664f,-0.030661463737487793f,-0.06259563565254211f,-0.1344406008720398f,0.35313835740089417f,0.02873902954161167f,0.09196598082780838f,0.3126353323459625f,-0.3646398186683655f},
{-0.40892091393470764f,0.043769627809524536f,-0.1879284828901291f,0.25968697667121887f,0.5609180331230164f,-0.051169753074645996f,-0.23312048614025116f,-0.390264093875885f,0.26103636622428894f,-0.1559126079082489f,-0.14134526252746582f,-0.2452119141817093f,-0.46458858251571655f,-0.16402840614318848f,0.07994696497917175f,-0.19317680597305298f},
{0.10697010159492493f,-0.12228584289550781f,-0.37870171666145325f,0.21184906363487244f,-0.37222859263420105f,-0.17138728499412537f,-0.1382003128528595f,0.3493293821811676f,-0.360889196395874f,-0.3875247836112976f,0.42142823338508606f,-0.3482915461063385f,-0.3289247751235962f,-0.2186824083328247f,0.09620395302772522f,-0.06898030638694763f},
{0.2847062647342682f,0.018552124500274658f,0.11435768008232117f,0.36562982201576233f,-0.047046810388565063f,0.30447837710380554f,0.2430230677127838f,0.2909286320209503f,-0.2802048921585083f,0.18043199181556702f,0.41849127411842346f,-0.287167489528656f,0.24394884705543518f,-0.14084559679031372f,-0.10168051719665527f,0.010465055704116821f},
{0.15459725260734558f,0.2284596711397171f,-0.14678864181041718f,-0.2826405167579651f,-3.0918989181518555f,0.1449601799249649f,-0.08742031455039978f,-0.9357023239135742f,-0.13340064883232117f,-0.2220277339220047f,0.0040720803663134575f,0.17651532590389252f,-0.8968222737312317f,0.21969160437583923f,0.5914236307144165f,-0.8322000503540039f},
{-0.408692330121994f,-0.050453294068574905f,-0.15351682901382446f,0.0922636091709137f,-0.35955044627189636f,0.12949898838996887f,0.03285527229309082f,0.38763079047203064f,-0.20705322921276093f,-0.25883403420448303f,0.12809070944786072f,-0.05215730890631676f,-0.6658473014831543f,0.16470779478549957f,-0.23339450359344482f,-0.040699247270822525f},
{-0.2991822361946106f,0.32027140259742737f,-0.5629739761352539f,-0.05932474136352539f,-1.0874625444412231f,1.0245612859725952f,-0.11253207921981812f,0.34576353430747986f,0.04814547300338745f,-0.35770976543426514f,-0.044228196144104004f,-0.22929511964321136f,0.19547978043556213f,0.5248737335205078f,0.36124154925346375f,0.27143019437789917f},
{-0.2675279378890991f,-0.39045897126197815f,-0.05424119159579277f,-0.13007770478725433f,1.437944769859314f,-1.7302147150039673f,-0.3452095687389374f,-1.4223114252090454f,-0.745403528213501f,-0.7274325489997864f,-0.49066221714019775f,-1.6464046239852905f,0.8509430885314941f,-0.8237955570220947f,0.001911899889819324f,0.6988413333892822f},
{-0.015470266342163086f,-0.529937207698822f,0.35546091198921204f,0.348036527633667f,0.1403835117816925f,-0.4197324514389038f,0.05196094512939453f,-0.008358269929885864f,-0.40752580761909485f,-0.38441595435142517f,0.13179203867912292f,-0.11511552333831787f,0.34031230211257935f,-0.04929199069738388f,-0.09811098128557205f,-0.19937199354171753f},
{0.1863725483417511f,0.18601037561893463f,-0.15775355696678162f,-0.46877092123031616f,0.44797858595848083f,0.024585137143731117f,0.04860696196556091f,0.17769548296928406f,-0.0749552771449089f,0.3378079831600189f,-0.5061431527137756f,0.19592127203941345f,0.3813547194004059f,0.09455892443656921f,-0.05183706805109978f,-0.012699469923973083f},
};
const float hout[16] = { 0.45773375034332275f,0.6764231324195862f,0.41992294788360596f,-0.06468239426612854f,0.17464998364448547f,0.24689403176307678f,0.04647764563560486f,0.2595721483230591f,0.08323294669389725f,0.11144406348466873f,0.14762791991233826f,-0.36595073342323303f,-0.6349490880966187f,0.21191029250621796f,0.6433769464492798f,-0.2769685387611389f };
const float b1[16] = { 0.3696094751358032f,1.7992044687271118f,-1.7145336866378784f,0.18997706472873688f,0.9549577832221985f,1.690210223197937f,-0.058932315558195114f,1.68743896484375f,0.44077587127685547f,-1.493913173675537f,0.5701789855957031f,1.6503576040267944f,-0.37873172760009766f,-0.894616961479187f,-1.087764859199524f,1.5419913530349731f };
const float b2[16] = { -0.2885071039199829f,-1.014089822769165f,-1.4564176797866821f,-0.7668818831443787f,-0.5584616661071777f,-0.49620234966278076f,0.03875614330172539f,-0.4831103980541229f,-1.20063054561615f,-1.912178635597229f,-0.32878178358078003f,0.04990300163626671f,-0.5751988887786865f,2.2356293201446533f,-0.2019418329000473f,0.697745680809021f };
const float b3[16] = { -1.963319182395935f,-0.5902930498123169f,0.1656760722398758f,-0.26326483488082886f,-2.454986333847046f,-0.20164278149604797f,-0.6144739985466003f,-0.6377184391021729f,-0.11426637321710587f,-0.05030348151922226f,-0.26522213220596313f,2.0851621627807617f,-1.2783746719360352f,1.249510407447815f,-1.4266045093536377f,-0.08144649863243103f };
const float bout[1] = { 0.05578257516026497f };
float VALVE_POS_RAW_NN = 0.0f;
float DDV_JOINT_POS_FF(float REF_JOINT_VEL);
int main()
{
HAL_Init();
SystemClock_Config();
/*********************************
*** Initialization
*********************************/
LED = 0;
pc.baud(9600);
// i2c init
i2c.frequency(400 * 1000); // 0.4 mHz
wait_ms(2); // Power Up wait
look_for_hardware_i2c(); // Hardware present
init_as5510(i2c_slave_addr1);
make_delay();
// // spi init
//eeprom.format(8,3);
//eeprom.frequency(5000000); //5M
enc.format(8,0);
enc.frequency(5000000); //5M
make_delay();
//rom
ROM_CALL_DATA();
make_delay();
// ADC init
Init_ADC();
make_delay();
// Pwm init
Init_PWM();
TIM4->CR1 ^= TIM_CR1_UDIS;
make_delay();
// TMR3 init
Init_TMR3();
TIM3->CR1 ^= TIM_CR1_UDIS;
make_delay();
// TMR2 init
// Init_TMR2();
// TIM2->CR1 ^= TIM_CR1_UDIS;
// make_delay();
// CAN
can.attach(&CAN_RX_HANDLER);
CAN_ID_INIT();
make_delay();
//Timer priority
NVIC_SetPriority(TIM3_IRQn, 2);
//NVIC_SetPriority(TIM2_IRQn, 3);
NVIC_SetPriority(TIM4_IRQn, 3);
//can.reset();
can.filter(msg.id, 0xFFFFF000, CANStandard);
// spi _ enc
spi_enc_set_init();
make_delay();
//DAC init
if (SENSING_MODE == 0) {
dac_1 = TORQUE_VREF / 3.3f;
dac_2 = 0.0f;
} else if (SENSING_MODE == 1) {
dac_1 = PRES_A_VREF / 3.3f;
dac_2 = PRES_B_VREF / 3.3f;
}
make_delay();
for (int i=0; i<50; i++) {
if(i%2==0)
ID_index_array[i] = - i * 0.5f;
else
ID_index_array[i] = (i+1) * 0.5f;
}
/************************************
*** Program is operating!
*************************************/
while(1) {
// if(timer_while==1000 && OPERATING_MODE==5) {
//if(timer_while==1000) {
//i2c
read_field(i2c_slave_addr1);
if(DIR_VALVE_ENC < 0) value = 1023 - value;
// if(LED==1) {
// LED=0;
// } else
// LED = 1;
timer_while = 0;
//}
timer_while ++;
//LED = 0;
if(NN_Control_Flag == 0) {
LED = 0;
}
else if(NN_Control_Flag == 1) {
int ind = 0;
for(int i=0; i<numpast_u; i++) {
input_NN[ind] = u_past[time_interval*i];
ind = ind + 1;
}
for(int i=0; i<numpast_x; i++) {
input_NN[ind] = x_past[time_interval*i] / 60.0f;
ind = ind + 1;
}
input_NN[ind] = (pos.sen / ENC_PULSE_PER_POSITION) / 60.0f;
ind = ind + 1;
// for(int i=0; i<numfuture_x; i++) {
// input_NN[ind] = x_future[time_interval*i+time_interval] / 60.0f;
// ind = ind + 1;
// }
for(int i=0; i<numpast_f; i++) {
input_NN[ind] = f_past[time_interval*i] / 10000.0f + 0.5f;
ind = ind + 1;
}
input_NN[ind] = torq.sen / 10000.0f + 0.5f;
ind = ind + 1;
for(int i=0; i<numfuture_f; i++) {
input_NN[ind] = (f_future[time_interval*i+time_interval] - torq.sen)/10000.0f+0.5f;
// input_NN[ind] = (f_future[time_interval*i+time_interval])/10000.0f+0.5f;
ind = ind + 1;
}
float output1[16] = { 0.0f };
float output2[16] = { 0.0f };
float output3[16] = { 0.0f };
float output = 0.0f;
for (int index2 = 0; index2 < 16; index2++) {
for (int index1 = 0; index1 < num_input; index1++) {
output1[index2] = output1[index2]
+ h1[index1][index2] * input_NN[index1];
}
output1[index2] = output1[index2] + b1[index2];
if (output1[index2] < 0) {
output1[index2] = 0;
}
}
for (int index2 = 0; index2 < 16; index2++) {
for (int index1 = 0; index1 < 16; index1++) {
output2[index2] = output2[index2]
+ h2[index1][index2] * output1[index1];
}
output2[index2] = output2[index2] + b2[index2];
if (output2[index2] < 0) {
output2[index2] = 0;
}
}
for (int index2 = 0; index2 < 16; index2++) {
for (int index1 = 0; index1 < 16; index1++) {
output3[index2] = output3[index2]
+ h3[index1][index2] * output2[index1];
}
output3[index2] = output3[index2] + b3[index2];
if (output3[index2] < 0) {
output3[index2] = 0;
}
}
for (int index2 = 0; index2 < 1; index2++) {
for (int index1 = 0; index1 < 16; index1++) {
output = output + hout[index1] * output3[index1];
}
output = output + bout[index2];
}
output = 1.0f/(1.0f+exp(-output));
output_normalized = output;
output = output * 20000.0f - 10000.0f;
if(output>=0) {
valve_pos.ref = output*0.0001f*((double)VALVE_MAX_POS - (double) VALVE_CENTER) + (double) VALVE_CENTER;
} else {
valve_pos.ref = -output*0.0001f*((double)VALVE_MIN_POS - (double) VALVE_CENTER) + (double) VALVE_CENTER;
}
// // torque feedback
// torq.err = f_past[0] - torq.sen; //[N]
//// torq.err_sum += torq.err/(float) TMR_FREQ_5k; //[N]
// torq.err_sum += torq.err/(float) 1500.0f; //[N]
//
//
// valve_pos.ref = ((float) P_GAIN_JOINT_TORQUE * torq.err + (float) I_GAIN_JOINT_TORQUE * torq.err_sum) * 0.01f + DDV_JOINT_POS_FF(vel.sen) + valve_pos.ref * 0.01f;
//
// if(I_GAIN_JOINT_TORQUE != 0) {
// double Ka = 1.0f / (double) I_GAIN_JOINT_TORQUE * 100.0f;
// if(valve_pos.ref>VALVE_MAX_POS) {
// double valve_pos_rem = valve_pos.ref - VALVE_MAX_POS;
// valve_pos_rem = valve_pos_rem * Ka;
// valve_pos.ref = VALVE_MAX_POS;
// torq.err_sum = torq.err_sum - valve_pos_rem/(float) 1500.0f;
// } else if(valve_pos.ref < VALVE_MIN_POS) {
// double valve_pos_rem = valve_pos.ref - VALVE_MIN_POS;
// valve_pos_rem = valve_pos_rem * Ka;
// valve_pos.ref = VALVE_MIN_POS;
// torq.err_sum = torq.err_sum - valve_pos_rem/(float) 1500.0f;
// }
// }
if(LED==1) {
LED=0;
} else
LED = 1;
}
//LED = 1;
}
}
float DDV_JOINT_POS_FF(float REF_JOINT_VEL)
{
int i = 0;
float Ref_Valve_Pos_FF = 0.0f;
for(i=0; i<VALVE_POS_NUM; i++) {
if(REF_JOINT_VEL >= min(JOINT_VEL[i],JOINT_VEL[i+1]) && REF_JOINT_VEL <= max(JOINT_VEL[i],JOINT_VEL[i+1])) {
if(i==0) {
if(JOINT_VEL[i+1] == JOINT_VEL[i]) {
Ref_Valve_Pos_FF = (float) VALVE_CENTER;
} else {
Ref_Valve_Pos_FF = ((float) 10/(JOINT_VEL[i+1] - JOINT_VEL[i]) * (REF_JOINT_VEL - JOINT_VEL[i])) + (float) VALVE_CENTER;
}
} else {
if(JOINT_VEL[i+1] == JOINT_VEL[i-1]) {
Ref_Valve_Pos_FF = (float) VALVE_CENTER;
} else {
Ref_Valve_Pos_FF = ((float) 10*(ID_index_array[i+1] - ID_index_array[i-1])/(JOINT_VEL[i+1] - JOINT_VEL[i-1]) * (REF_JOINT_VEL - JOINT_VEL[i-1])) + (float) VALVE_CENTER + (float) (10*ID_index_array[i-1]);
}
}
break;
}
}
if(REF_JOINT_VEL > max(JOINT_VEL[VALVE_POS_NUM-1], JOINT_VEL[VALVE_POS_NUM-2])) {
Ref_Valve_Pos_FF = (float) VALVE_MAX_POS;
} else if(REF_JOINT_VEL < min(JOINT_VEL[VALVE_POS_NUM-1], JOINT_VEL[VALVE_POS_NUM-2])) {
Ref_Valve_Pos_FF = (float) VALVE_MIN_POS;
}
Ref_Valve_Pos_FF = (float) VELOCITY_COMP_GAIN * 0.01f * (float) (Ref_Valve_Pos_FF - (float) VALVE_CENTER);
return Ref_Valve_Pos_FF;
}
void VALVE_POS_CONTROL(float REF_VALVE_POS)
{
int i = 0;
if(REF_VALVE_POS > VALVE_MAX_POS) {
REF_VALVE_POS = VALVE_MAX_POS;
} else if(REF_VALVE_POS < VALVE_MIN_POS) {
REF_VALVE_POS = VALVE_MIN_POS;
}
valve_pos_err = (float) (REF_VALVE_POS - value);
valve_pos_err_diff = valve_pos_err - valve_pos_err_old;
valve_pos_err_old = valve_pos_err;
valve_pos_err_sum += valve_pos_err;
if (valve_pos_err_sum > 1000.0f) valve_pos_err_sum = 1000.0f;
if (valve_pos_err_sum<-1000.0f) valve_pos_err_sum = -1000.0f;
VALVE_PWM_RAW_FB = P_GAIN_VALVE_POSITION * valve_pos_err + I_GAIN_VALVE_POSITION * valve_pos_err_sum + D_GAIN_VALVE_POSITION * valve_pos_err_diff;
for(i=0; i<24; i++) {
if(REF_VALVE_POS >= min(VALVE_POS_VS_PWM[i],VALVE_POS_VS_PWM[i+1]) && (float) REF_VALVE_POS <= max(VALVE_POS_VS_PWM[i],VALVE_POS_VS_PWM[i+1])) {
if(i==0) {
VALVE_PWM_RAW_FF = (float) 1000.0f / (float) (VALVE_POS_VS_PWM[i+1] - VALVE_POS_VS_PWM[i]) * ((float) REF_VALVE_POS - VALVE_POS_VS_PWM[i]);
} else {
VALVE_PWM_RAW_FF = (float) 1000.0f* (float) (ID_index_array[i+1] - ID_index_array[i-1])/(VALVE_POS_VS_PWM[i+1] - VALVE_POS_VS_PWM[i-1]) * ((float) REF_VALVE_POS - VALVE_POS_VS_PWM[i-1]) + 1000.0f * (float) ID_index_array[i-1];
}
break;
}
}
Vout.ref = VALVE_PWM_RAW_FF + VALVE_PWM_RAW_FB;
}
#define LT_MAX_IDX 57
float LT_PWM_duty[LT_MAX_IDX] = {-100.0f, -80.0f, -60.0f, -50.0f, -40.0f, -35.0f, -30.0f, -25.0f, -20.0f,
-19.0f, -18.0f, -17.0f, -16.0f, -15.0f, -14.0f, -13.0f, -12.0f, -11.0f, -10.0f,
-9.0f, -8.0f, -7.0f, -6.0f, -5.0f, -4.0f, -3.0f, -2.0f, -1.0f, 0.0f,
1.0f, 2.0f, 3.0f, 4.0f, 5.0f, 6.0f, 7.0f, 8.0f, 9.0f, 10.0f,
11.0f, 12.0f, 13.0f, 14.0f, 15.0f, 16.0f, 17.0f, 18.0f, 19.0f, 20.0f,
25.0f, 30.0f, 35.0f, 40.0f, 50.0f, 60.0f, 80.0f, 100.0f
}; // duty
float LT_Voltage_Output[LT_MAX_IDX] = {-230.0f, -215.0f, -192.5f, -185.0f, -177.5f, -170.0f, -164.0f, -160.0f, -150.0f,
-150.0f, -145.0f, -145.0f, -145.0f, -135.0f, -135.0f, -135.0f, -127.5f, -127.5f, -115.0f,
-115.0f, -115.0F, -100.0f, -100.0f, -100.0f, -60.0f, -60.0f, -10.0f, -5.0f, 0.0f,
7.5f, 14.0f, 14.0f, 14.0f, 42.5f, 42.5f, 42.5f, 80.0f, 80.0f, 105.0f,
105.0f, 105.0f, 120.0f, 120.0f, 120.0f, 131.0f, 131.0f, 140.0f, 140.0f, 140.0f,
155.0f, 160.0f, 170.0f, 174.0f, 182.0f, 191.0f, 212.0f, 230.0f
}; // mV
float PWM_duty_byLT(float Ref_V)
{
float PWM_duty = 0.0f;
if(Ref_V<LT_Voltage_Output[0]) {
PWM_duty = (Ref_V-LT_Voltage_Output[0])/1.5f+LT_PWM_duty[0];
} else if (Ref_V>=LT_Voltage_Output[LT_MAX_IDX-1]) {
PWM_duty = (Ref_V-LT_Voltage_Output[LT_MAX_IDX-1])/1.5f+LT_PWM_duty[LT_MAX_IDX-1];
} else {
int idx = 0;
for(idx=0; idx<LT_MAX_IDX-1; idx++) {
float ini_x = LT_Voltage_Output[idx];
float fin_x = LT_Voltage_Output[idx+1];
float ini_y = LT_PWM_duty[idx];
float fin_y = LT_PWM_duty[idx+1];
if(Ref_V>=ini_x && Ref_V<fin_x) {
PWM_duty = (fin_y-ini_y)/(fin_x-ini_x)*(Ref_V-ini_x) + ini_y;
break;
}
}
}
return PWM_duty;
}
/*******************************************************************************
TIMER INTERRUPT
*******************************************************************************/
float FREQ_TMR4 = (float)FREQ_20k;
float DT_TMR4 = (float)DT_20k;
long CNT_TMR4 = 0;
int TMR4_FREQ_10k = (int)FREQ_10k;
extern "C" void TIM4_IRQHandler(void)
{
if (TIM4->SR & TIM_SR_UIF ) {
/*******************************************************
*** Sensor Read & Data Handling
********************************************************/
//Encoder
if (CNT_TMR4 % (int) ((int) FREQ_TMR4/TMR4_FREQ_10k) == 0) {
ENC_UPDATE();
}
ADC1->CR2 |= 0x40000000;
if (SENSING_MODE == 0) {
// Torque Sensing (0~210)bar =============================================
float pres_A_new = (((float) ADC1->DR) - 2047.5f);
double alpha_update_ft = 1.0f / (1.0f + FREQ_TMR4 / (2.0f * 3.14f * 100.0f)); // f_cutoff : 200Hz
pres_A.sen = (1.0f - alpha_update_ft) * pres_A.sen + alpha_update_ft * pres_A_new;
torq.sen = -pres_A.sen / TORQUE_SENSOR_PULSE_PER_TORQUE;
// float alpha_update_pres_A = 1.0f/(1.0f + FREQ_TMR4/(2.0f*3.14f*100.0f));
//// float pres_A_new = ((float)ADC1->DR - PRES_A_NULL) / PRES_SENSOR_A_PULSE_PER_BAR;
// float pres_A_new = ((float)ADC1->DR);
// pres_A.sen = pres_A.sen*(1.0f-alpha_update_pres_A)+pres_A_new*(alpha_update_pres_A);
// torq.sen = - (pres_A.sen-2048.0f); //pulse -2047~2047
} else if (SENSING_MODE == 1) {
// Pressure Sensing (0~210)bar =============================================
float pres_A_new = (((float)ADC1->DR) - PRES_A_NULL);
float pres_B_new = (((float)ADC2->DR) - PRES_B_NULL);
double alpha_update_pres = 1.0f / (1.0f + FREQ_TMR4 / (2.0f * 3.14f * 200.0f)); // f_cutoff : 500Hz
pres_A.sen = (1.0f - alpha_update_pres) * pres_A.sen + alpha_update_pres * pres_A_new;
pres_B.sen = (1.0f - alpha_update_pres) * pres_B.sen + alpha_update_pres * pres_B_new;
CUR_PRES_A_BAR = pres_A.sen / PRES_SENSOR_A_PULSE_PER_BAR;
CUR_PRES_B_BAR = pres_B.sen / PRES_SENSOR_B_PULSE_PER_BAR;
if ((OPERATING_MODE & 0x01) == 0) { // Rotary Actuator
torq.sen = (PISTON_AREA_A * CUR_PRES_A_BAR - PISTON_AREA_B * CUR_PRES_B_BAR) * 0.0001f; // mm^3*bar >> Nm
} else if ((OPERATING_MODE & 0x01) == 1) { // Linear Actuator
torq.sen = (PISTON_AREA_A * CUR_PRES_A_BAR - PISTON_AREA_B * CUR_PRES_B_BAR) * 0.1f; // mm^2*bar >> N
}
}
// //Pressure sensor A
// ADC1->CR2 |= 0x40000000; // adc _ 12bit
// //while((ADC1->SR & 0b10));
// float alpha_update_pres_A = 1.0f/(1.0f + FREQ_TMR4/(2.0f*3.14f*100.0f));
// float pres_A_new = ((float)ADC1->DR);
// pres_A.sen = pres_A.sen*(1.0f-alpha_update_pres_A)+pres_A_new*(alpha_update_pres_A);
// torq.sen = - (pres_A.sen-2048.0f); //pulse -2047~2047 //SW just changed the sign to correct the direction of loadcell on LIGHT. Correct later.
//
//
// //Pressure sensor B
// float alpha_update_pres_B = 1.0f/(1.0f + FREQ_TMR4/(2.0f*3.14f*100.0f));
// float pres_B_new = ((float)ADC2->DR);
// pres_B.sen = pres_B.sen*(1.0f-alpha_update_pres_B)+pres_B_new*(alpha_update_pres_B);
// //torq.sen = pres_A.sen * (float) PISTON_AREA_A - pres_B.sen * (float) PISTON_AREA_B;
//Current
//ADC3->CR2 |= 0x40000000; // adc _ 12bit
//int raw_cur = ADC3->DR;
//while((ADC3->SR & 0b10));
float alpha_update_cur = 1.0f/(1.0f + FREQ_TMR4/(2.0f*3.14f*500.0f)); // f_cutoff : 500Hz
float cur_new = ((float)ADC3->DR-2048.0f)*20.0f/4096.0f; // unit : mA
cur.sen=cur.sen*(1.0f-alpha_update_cur)+cur_new*(alpha_update_cur);
//cur.sen = raw_cur;
CNT_TMR4++;
}
TIM4->SR = 0x0; // reset the status register
}
int j =0;
float FREQ_TMR3 = (float)FREQ_5k;
float DT_TMR3 = (float)DT_5k;
int cnt_trans = 0;
double VALVE_POS_RAW_FORCE_FB_LOGGING = 0.0f;
int can_rest =0;
extern "C" void TIM3_IRQHandler(void)
{
if (TIM3->SR & TIM_SR_UIF ) {
if (((OPERATING_MODE&0b110)>>1) == 0) {
K_v = 0.4f; // Moog (LPM >> mA) , 100bar
mV_PER_mA = 500.0f; // 5000mV/10mA
mV_PER_pulse = 0.5f; // 5000mV/10000pulse
mA_PER_pulse = 0.001f; // 10mA/10000pulse
} else if (((OPERATING_MODE&0b110)>>1) == 1) {
K_v = 0.5f; // KNR (LPM >> mA) , 100bar
mV_PER_mA = 166.6666f; // 5000mV/30mA
mV_PER_pulse = 0.5f; // 5000mV/10000pulse
mA_PER_pulse = 0.003f; // 30mA/10000pulse
}
if(MODE_POS_FT_TRANS == 1) {
alpha_trans = (float)(1.0f - cos(3.141592f * (float)cnt_trans * DT_TMR3 /3.0f))/2.0f;
cnt_trans++;
torq.err_sum = 0;
if((float)cnt_trans * DT_TMR3 > 3.0f)
MODE_POS_FT_TRANS = 2;
} else if(MODE_POS_FT_TRANS == 3) {
alpha_trans = (float)(1.0f + cos(3.141592f * (float)cnt_trans * DT_TMR3 /3.0f))/2.0f;
cnt_trans++;
torq.err_sum = 0;
if((float) cnt_trans * DT_TMR3 > 3.0f )
MODE_POS_FT_TRANS = 0;
} else if(MODE_POS_FT_TRANS == 2) {
alpha_trans = 1.0f;
cnt_trans = 0;
} else {
alpha_trans = 0.0f;
cnt_trans = 0;
}
int UTILITY_MODE = 0;
int CONTROL_MODE = 0;
if (CONTROL_UTILITY_MODE >= 20 || CONTROL_UTILITY_MODE == 0) {
UTILITY_MODE = CONTROL_UTILITY_MODE;
CONTROL_MODE = MODE_NO_ACT;
} else {
CONTROL_MODE = CONTROL_UTILITY_MODE;
UTILITY_MODE = MODE_NO_ACT;
}
// UTILITY MODE ------------------------------------------------------------
switch (UTILITY_MODE) {
case MODE_NO_ACT: {
break;
}
case MODE_TORQUE_SENSOR_NULLING: {
// DAC Voltage reference set
if (TMR3_COUNT_TORQUE_NULL < TMR_FREQ_5k * 2) {
CUR_TORQUE_sum += torq.sen;
if (TMR3_COUNT_TORQUE_NULL % 10 == 0) {
CUR_TORQUE_mean = CUR_TORQUE_sum / 10.0f;
CUR_TORQUE_sum = 0;
TORQUE_VREF += 0.000003f * (0.0f - CUR_TORQUE_mean);
if (TORQUE_VREF > 3.3f) TORQUE_VREF = 3.3f;
if (TORQUE_VREF < 0.0f) TORQUE_VREF = 0.0f;
//spi_eeprom_write(RID_TORQUE_SENSOR_VREF, (int16_t) (TORQUE_VREF * 1000.0));
dac_1 = TORQUE_VREF / 3.3f;
}
} else {
CONTROL_UTILITY_MODE = MODE_NO_ACT;
TMR3_COUNT_TORQUE_NULL = 0;
CUR_TORQUE_sum = 0;
CUR_TORQUE_mean = 0;
ROM_RESET_DATA();
dac_1 = TORQUE_VREF / 3.3f;
}
TMR3_COUNT_TORQUE_NULL++;
break;
}
// case MODE_VALVE_NULLING_AND_DEADZONE_SETTING: {
// if (TMR3_COUNT_DEADZONE == 0) {
// if (pos_plus_end == pos_minus_end) need_enc_init = true;
// else temp_time = 0;
// }
// if (need_enc_init) {
// if (TMR3_COUNT_DEADZONE < (int) (0.5f * (float) TMR_FREQ_5k)) {
// V_out = VALVE_VOLTAGE_LIMIT * 1000.0f;
// pos_plus_end = pos.sen;
// } else if (TMR3_COUNT_DEADZONE < TMR_FREQ_5k) {
// V_out = -VALVE_VOLTAGE_LIMIT * 1000.0f;
// pos_minus_end = pos.sen;
// } else if (TMR3_COUNT_DEADZONE == TMR_FREQ_5k) need_enc_init = false;
// temp_time = TMR_FREQ_5k;
// }
//
// if (temp_time <= TMR3_COUNT_DEADZONE && TMR3_COUNT_DEADZONE < (temp_time + TMR_FREQ_5k)) {
// V_out = (float) P_GAIN_JOINT_POSITION * (0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end - (float) pos.sen);
// VALVE_CENTER = VALVE_DEADZONE_PLUS = VALVE_DEADZONE_MINUS = 0;
//
// } else if (temp_time <= TMR3_COUNT_DEADZONE && TMR3_COUNT_DEADZONE < (temp_time + (int) (1.9f * (float) TMR_FREQ_5k))) {
// V_out = 0;
// CUR_VELOCITY_sum += CUR_VELOCITY;
// } else if (TMR3_COUNT_DEADZONE == (temp_time + 2 * TMR_FREQ_5k)) {
// if (CUR_VELOCITY_sum == 0) DZ_dir = 1;
// else if (CUR_VELOCITY_sum > 0) DZ_dir = 1;
// else if (CUR_VELOCITY_sum < 0) DZ_dir = -1;
// else DZ_temp_cnt2 = DZ_end;
// CUR_VELOCITY_sum = 0;
// } else if (TMR3_COUNT_DEADZONE > (temp_time + 2 * TMR_FREQ_5k)) {
// if (TMR3_COUNT_DEADZONE > (temp_time + 10 * TMR_FREQ_5k)) DZ_temp_cnt2 = DZ_end;
//
// // Position of Dead Zone
// // (CUR_VELOCITY < 0) (CUR_VELOCITY == 0) (CUR_VELOCITY > 0)
// // | / | / |/
// // | ______/ ___|___/ ______/|
// // |/ / | / |
// // /| / | / |
// // 0V 0V 0V
//
// if (DZ_temp_cnt2 < DZ_end) {
// if (TMR3_COUNT_DEADZONE % 20 != 0) {
// CUR_VELOCITY_sum += CUR_VELOCITY;
// } else {
// V_out -= DZ_dir;
// if (CUR_VELOCITY_sum * DZ_dir < 0) DZ_temp_cnt++;
// CUR_VELOCITY_sum = 0;
// }
// if (DZ_temp_cnt == 5) {
// if (DZ_dir >= 0) VALVE_DEADZONE_MINUS = (int16_t) V_out;
// else VALVE_DEADZONE_PLUS = (int16_t) V_out;
// DZ_dir = -DZ_dir;
// DZ_temp_cnt = 0;
// DZ_temp_cnt2++;
// }
// } else {
// TMR3_COUNT_DEADZONE = -1;
// VALVE_CENTER = VALVE_DEADZONE_PLUS / 2 + VALVE_DEADZONE_MINUS / 2;
// if (VALVE_DEADZONE_PLUS < VALVE_DEADZONE_MINUS) {
// VALVE_DEADZONE_PLUS = VALVE_CENTER;
// VALVE_DEADZONE_MINUS = VALVE_CENTER;
// }
// V_out = 0;
//
// ROM_RESET_DATA();
//
// //spi_eeprom_write(RID_VALVE_DEADZONE_PLUS, VALVE_DEADZONE_PLUS);
// //spi_eeprom_write(RID_VALVE_DEADZONE_MINUS, VALVE_DEADZONE_MINUS);
//
// CONTROL_MODE = MODE_NO_ACT;
// DZ_temp_cnt2 = 0;
// }
// }
// TMR3_COUNT_DEADZONE++;
// break;
// }
case MODE_FIND_HOME: {
if (FINDHOME_STAGE == FINDHOME_INIT) {
cnt_findhome = 0;
cnt_vel_findhome = 0;
//REFERENCE_MODE = MODE_REF_NO_ACT; // Stop taking reference data from PODO
pos.ref = pos.sen;
vel.ref = 0.0f;
FINDHOME_STAGE = FINDHOME_GOTOLIMIT;
} else if (FINDHOME_STAGE == FINDHOME_GOTOLIMIT) {
int cnt_check_enc = (TMR_FREQ_5k/20);
if(cnt_findhome%cnt_check_enc == 0) {
FINDHOME_POSITION = pos.sen;
FINDHOME_VELOCITY = FINDHOME_POSITION - FINDHOME_POSITION_OLD;
FINDHOME_POSITION_OLD = FINDHOME_POSITION;
}
cnt_findhome++;
if (abs(FINDHOME_VELOCITY) <= 1) {
cnt_vel_findhome = cnt_vel_findhome + 1;
} else {
cnt_vel_findhome = 0;
}
if ((cnt_vel_findhome < 3*TMR_FREQ_5k) && cnt_findhome < 10*TMR_FREQ_5k) { // wait for 3sec
//REFERENCE_MODE = MODE_REF_NO_ACT;
if (HOMEPOS_OFFSET > 0) pos.ref = pos.ref + 12.0f;
else pos.ref = pos.ref - 12.0f;
// pos.err = pos.ref_home_pos - pos.sen;
// float VALVE_POS_RAW_POS_FB = 0.0f;
// VALVE_POS_RAW_POS_FB = (float) P_GAIN_JOINT_POSITION * pos.err/(float) ENC_PULSE_PER_POSITION * 0.01f;
// valve_pos.ref = VALVE_POS_RAW_POS_FB + (float) VALVE_CENTER;
// VALVE_POS_CONTROL(valve_pos.ref);
CONTROL_MODE = MODE_JOINT_CONTROL;
alpha_trans = 0.0f;
} else {
ENC_SET(HOMEPOS_OFFSET);
// ENC_SET_ZERO();
INIT_REF_POS = HOMEPOS_OFFSET;
REF_POSITION = 0;
REF_VELOCITY = 0;
FINDHOME_POSITION = 0;
FINDHOME_POSITION_OLD = 0;
FINDHOME_VELOCITY = 0;
cnt_findhome = 0;
cnt_vel_findhome = 0;
FINDHOME_STAGE = FINDHOME_ZEROPOSE;
cnt_findhome = 0;
pos.ref = 0.0f;
vel.ref = 0.0f;
pos.ref_home_pos = 0.0f;
vel.ref_home_pos = 0.0f;
//FINDHOME_STAGE = FINDHOME_INIT;
//CONTROL_UTILITY_MODE = MODE_JOINT_CONTROL;
}
} else if (FINDHOME_STAGE == FINDHOME_ZEROPOSE) {
int T_move = 2*TMR_FREQ_5k;
pos.ref = (0.0f - (float)INIT_REF_POS)*0.5f*(1.0f - cos(3.14159f * (float)cnt_findhome / (float)T_move)) + (float)INIT_REF_POS;
//pos.ref = 0.0f;
vel.ref = 0.0f;
// input for position control
// CONTROL_MODE = MODE_JOINT_CONTROL;
alpha_trans = 0.0f;
double torq_ref = 0.0f;
pos.err = (pos.ref - pos.sen)/(float)(ENC_PULSE_PER_POSITION); //[mm]
vel.err = (0.0f - vel.sen)/(float)(ENC_PULSE_PER_POSITION); //[mm/s]
pos.err_sum += pos.err/(float) TMR_FREQ_5k; //[mm]
if (((OPERATING_MODE&0b110)>>1) == 0 || ((OPERATING_MODE&0b110)>>1) == 1) {
double I_REF_POS = 0.0f;
double I_REF_FORCE_FB = 0.0f; // I_REF by Force Feedback
double I_REF_VC = 0.0f; // I_REF for velocity compensation
double temp_vel_pos = 0.0f;
double temp_vel_torq = 0.0f;
double wn_Pos = 2.0f * PI * 5.0f; // f_cut : 5Hz Position Control
if ((OPERATING_MODE & 0x01) == 0) { // Rotary Mode
temp_vel_pos = (0.01f * (double) P_GAIN_JOINT_POSITION * wn_Pos * pos.err + 0.01f * (double) I_GAIN_JOINT_POSITION * wn_Pos * pos.err_sum + 0.01f * (double) VELOCITY_COMP_GAIN * vel.ref / ENC_PULSE_PER_POSITION) * 3.14159f / 180.0f; // rad/s
// L when P-gain = 100, f_cut = 10Hz L feedforward velocity
} else if ((OPERATING_MODE & 0x01) == 1) {
temp_vel_pos = (0.01f * (double) P_GAIN_JOINT_POSITION * wn_Pos * pos.err + 0.01f * (double) I_GAIN_JOINT_POSITION * wn_Pos * pos.err_sum + 0.01f * (double) VELOCITY_COMP_GAIN * vel.ref / ENC_PULSE_PER_POSITION); // mm/s
// L when P-gain = 100, f_cut = 10Hz L feedforward velocity
}
if (temp_vel_pos > 0.0f) I_REF_POS = temp_vel_pos * ((double) PISTON_AREA_A * 0.00006f / (K_v * sqrt(2.0f * alpha3 / (alpha3 + 1.0f))));
else I_REF_POS = temp_vel_pos * ((double) PISTON_AREA_B * 0.00006f / (K_v * sqrt(2.0f / (alpha3 + 1.0f))));
I_REF = I_REF_POS;
} else {
float VALVE_POS_RAW_FORCE_FB = 0.0f;
VALVE_POS_RAW_FORCE_FB = DDV_JOINT_POS_FF(vel.sen) + (P_GAIN_JOINT_POSITION * 0.01f * pos.err + DDV_JOINT_POS_FF(vel.ref));
if (VALVE_POS_RAW_FORCE_FB >= 0) {
valve_pos.ref = VALVE_POS_RAW_FORCE_FB + VALVE_DEADZONE_PLUS;
} else {
valve_pos.ref = VALVE_POS_RAW_FORCE_FB + VALVE_DEADZONE_MINUS;
}
VALVE_POS_CONTROL(valve_pos.ref);
V_out = (float) Vout.ref;
}
// pos.err = pos.ref - (float)pos.sen;
// float VALVE_POS_RAW_POS_FB = 0.0f;
// VALVE_POS_RAW_POS_FB = (float) P_GAIN_JOINT_POSITION * 0.01f * pos.err/(float) ENC_PULSE_PER_POSITION;
// valve_pos.ref = VALVE_POS_RAW_POS_FB + (float) VALVE_CENTER;
// VALVE_POS_CONTROL(valve_pos.ref);
cnt_findhome++;
if (cnt_findhome >= T_move) {
//REFERENCE_MODE = MODE_REF_DIRECT;
cnt_findhome = 0;
pos.ref = 0.0f;
vel.ref = 0.0f;
pos.ref_home_pos = 0.0f;
vel.ref_home_pos = 0.0f;
FINDHOME_STAGE = FINDHOME_INIT;
CONTROL_UTILITY_MODE = MODE_JOINT_CONTROL;
}
}
break;
}
// case MODE_VALVE_GAIN_SETTING: {
// if (TMR3_COUNT_FLOWRATE == 0) {
// if (pos_plus_end == pos_minus_end) need_enc_init = true;
// else {
// V_out = -VALVE_VOLTAGE_LIMIT * 1000.0f;
// temp_time = (int) (0.5f * (float) TMR_FREQ_5k);
// }
// }
// if (need_enc_init) {
// if (TMR3_COUNT_FLOWRATE < (int) (0.5f * (float) TMR_FREQ_5k)) {
// V_out = VALVE_VOLTAGE_LIMIT * 1000.0f;
// pos_plus_end = pos.sen;
// } else if (TMR3_COUNT_FLOWRATE < TMR_FREQ_5k) {
// V_out = -VALVE_VOLTAGE_LIMIT * 1000.0f;
// pos_minus_end = pos.sen;
// } else if (TMR3_COUNT_FLOWRATE == TMR_FREQ_5k) {
// need_enc_init = false;
// check_vel_pos_init = (int) (0.9f * (float) (pos_plus_end - pos_minus_end));
// check_vel_pos_fin = (int) (0.95f * (float) (pos_plus_end - pos_minus_end));
// check_vel_pos_interv = check_vel_pos_fin - check_vel_pos_init;
// }
// temp_time = TMR_FREQ_5k;
// }
// TMR3_COUNT_FLOWRATE++;
// if (TMR3_COUNT_FLOWRATE > temp_time) {
// if (flag_flowrate % 2 == 0) { // (+)
// VALVE_VOLTAGE = 1000.0f * (float) (flag_flowrate / 2 + 1);
// V_out = VALVE_VOLTAGE;
// if (pos.sen > (pos_minus_end + check_vel_pos_init) && pos.sen < (pos_minus_end + check_vel_pos_fin)) {
// fl_temp_cnt++;
// } else if (pos.sen >= (pos_minus_end + check_vel_pos_fin) && CUR_VELOCITY == 0) {
// VALVE_GAIN_LPM_PER_V[flag_flowrate] = 0.95873f * 0.5757f * (float) TMR_FREQ_5k / 10000.0 * (float) check_vel_pos_interv / (float) fl_temp_cnt / VALVE_VOLTAGE; // 0.9587=6*pi/65536*10000 0.5757=0.02525*0.02*0.0095*2*60*1000
// // VALVE_GAIN_LPM_PER_V[flag_flowrate] = (float) TMR_FREQ_10k * (float) check_vel_pos_interv / (float) fl_temp_cnt / VALVE_VOLTAGE; // PULSE/sec
// fl_temp_cnt2++;
// }
// } else if (flag_flowrate % 2 == 1) { // (-)
// VALVE_VOLTAGE = -1. * (float) (flag_flowrate / 2 + 1);
// V_out = VALVE_VOLTAGE;
// if (pos.sen < (pos_plus_end - check_vel_pos_init) && pos.sen > (pos_plus_end - check_vel_pos_fin)) {
// fl_temp_cnt++;
// } else if (pos.sen <= (pos_plus_end - check_vel_pos_fin) && CUR_VELOCITY == 0) {
// VALVE_GAIN_LPM_PER_V[flag_flowrate] = 0.95873f * 0.5757f * (float) TMR_FREQ_5k / 10000.0f * (float) check_vel_pos_interv / (float) fl_temp_cnt / (-VALVE_VOLTAGE);
// // VALVE_GAIN_LPM_PER_V[flag_flowrate] = (float) TMR_FREQ_10k * (float) check_vel_pos_interv / (float) fl_temp_cnt / (-VALVE_VOLTAGE); // PULSE/sec
// fl_temp_cnt2++;
// }
// }
// if (fl_temp_cnt2 == 100) {
//
// ROM_RESET_DATA();
//
// //spi_eeprom_write(RID_VALVE_GAIN_PLUS_1 + flag_flowrate, (int16_t) (VALVE_GAIN_LPM_PER_V[flag_flowrate] * 100.0f));
// cur_vel_sum = 0;
// fl_temp_cnt = 0;
// fl_temp_cnt2 = 0;
// flag_flowrate++;
// }
// if (flag_flowrate == 10) {
// V_out = 0;
// flag_flowrate = 0;
// TMR3_COUNT_FLOWRATE = 0;
// valve_gain_repeat_cnt++;
// if (valve_gain_repeat_cnt >= 1) {
// CONTROL_MODE = MODE_NO_ACT;
// valve_gain_repeat_cnt = 0;
// }
//
// }
// break;
// }
//
// }
case MODE_PRESSURE_SENSOR_NULLING: {
// DAC Voltage reference set
if (TMR3_COUNT_PRES_NULL < TMR_FREQ_5k * 2) {
CUR_PRES_A_sum += pres_A.sen;
CUR_PRES_B_sum += pres_B.sen;
if (TMR3_COUNT_PRES_NULL % 10 == 0) {
CUR_PRES_A_mean = CUR_PRES_A_sum / 10.0f;
CUR_PRES_B_mean = CUR_PRES_B_sum / 10.0f;
CUR_PRES_A_sum = 0;
CUR_PRES_B_sum = 0;
float VREF_NullingGain = 0.0003f;
PRES_A_VREF = PRES_A_VREF + VREF_NullingGain * CUR_PRES_A_mean;
PRES_B_VREF = PRES_B_VREF + VREF_NullingGain * CUR_PRES_B_mean;
if (PRES_A_VREF > 3.3f) PRES_A_VREF = 3.3f;
if (PRES_A_VREF < 0.0f) PRES_A_VREF = 0.0f;
if (PRES_B_VREF > 3.3f) PRES_B_VREF = 3.3f;
if (PRES_B_VREF < 0.0f) PRES_B_VREF = 0.0f;
dac_1 = PRES_A_VREF / 3.3f;
dac_2 = PRES_B_VREF / 3.3f;
}
} else {
CONTROL_UTILITY_MODE = MODE_NO_ACT;
TMR3_COUNT_PRES_NULL = 0;
CUR_PRES_A_sum = 0;
CUR_PRES_B_sum = 0;
CUR_PRES_A_mean = 0;
CUR_PRES_B_mean = 0;
ROM_RESET_DATA();
dac_1 = PRES_A_VREF / 3.3f;
dac_2 = PRES_B_VREF / 3.3f;
//pc.printf("nulling end");
}
TMR3_COUNT_PRES_NULL++;
break;
}
// case MODE_PRESSURE_SENSOR_CALIB: {
// if (TMR3_COUNT_PRES_CALIB < 2 * TMR_FREQ_5k) {
// V_out = -VALVE_VOLTAGE_LIMIT * 1000.0f;
// if (TMR3_COUNT_PRES_CALIB >= TMR_FREQ_5k) {
// CUR_PRES_A_sum += CUR_PRES_A;
// }
// } else if (TMR3_COUNT_PRES_CALIB < 4 * TMR_FREQ_5k) {
// V_out = VALVE_VOLTAGE_LIMIT * 1000.0f;
// if (TMR3_COUNT_PRES_CALIB >= 3 * TMR_FREQ_5k) {
// CUR_PRES_B_sum += CUR_PRES_B;
// }
// } else {
// CONTROL_MODE = MODE_NO_ACT;
// TMR3_COUNT_PRES_CALIB = 0;
// V_out = 0;
// PRES_SENSOR_A_PULSE_PER_BAR = CUR_PRES_A_sum / ((float) TMR_FREQ_5k - 1.0f) - PRES_A_NULL;
// PRES_SENSOR_A_PULSE_PER_BAR = PRES_SENSOR_A_PULSE_PER_BAR / ((float) PRES_SUPPLY - 1.0f);
// PRES_SENSOR_B_PULSE_PER_BAR = CUR_PRES_B_sum / ((float) TMR_FREQ_5k - 1.0f) - PRES_B_NULL;
// PRES_SENSOR_B_PULSE_PER_BAR = PRES_SENSOR_B_PULSE_PER_BAR / ((float) PRES_SUPPLY - 1.0f);
// CUR_PRES_A_sum = 0;
// CUR_PRES_B_sum = 0;
// CUR_PRES_A_mean = 0;
// CUR_PRES_B_mean = 0;
//
// ROM_RESET_DATA();
//
// //spi_eeprom_write(RID_PRES_SENSOR_A_PULSE_PER_BAR, (int16_t) (PRES_SENSOR_A_PULSE_PER_BAR * 100.0f));
// //spi_eeprom_write(RID_PRES_SENSOR_B_PULSE_PER_BAR, (int16_t) (PRES_SENSOR_B_PULSE_PER_BAR * 100.0f));
// }
// TMR3_COUNT_PRES_CALIB++;
// break;
// }
// case MODE_ROTARY_FRICTION_TUNING: {
// if (TMR3_COUNT_ROTARY_FRIC_TUNE % (5 * TMR_FREQ_5k) == 0) freq_fric_tune = 4.0f + 3.0f * sin(2 * 3.14159f * 0.5f * TMR3_COUNT_ROTARY_FRIC_TUNE * 0.0001f * 0.05f);
// V_out = PWM_out * sin(2 * 3.14159f * freq_fric_tune * TMR3_COUNT_ROTARY_FRIC_TUNE * 0.0001f);
// if (V_out > 0) V_out = VALVE_VOLTAGE_LIMIT * 1000.0f;
// else V_out = -VALVE_VOLTAGE_LIMIT * 1000.0f;
// TMR3_COUNT_ROTARY_FRIC_TUNE++;
// if (TMR3_COUNT_ROTARY_FRIC_TUNE > TUNING_TIME * TMR_FREQ_5k) {
// TMR3_COUNT_ROTARY_FRIC_TUNE = 0;
// V_out = 0.0f;
// CONTROL_MODE = MODE_NO_ACT;
// }
// break;
// }
case MODE_DDV_POS_VS_PWM_ID: {
CONTROL_MODE = MODE_VALVE_OPEN_LOOP;
VALVE_ID_timer = VALVE_ID_timer + 1;
if(VALVE_ID_timer < TMR_FREQ_5k*1) {
Vout.ref = 3000.0f * sin(2.0f*3.14f*VALVE_ID_timer/TMR_FREQ_5k * 100.0f);
} else if(VALVE_ID_timer < TMR_FREQ_5k*2) {
Vout.ref = 1000.0f*(ID_index_array[ID_index]);
} else if(VALVE_ID_timer == TMR_FREQ_5k*2) {
VALVE_POS_TMP = 0;
data_num = 0;
} else if(VALVE_ID_timer < TMR_FREQ_5k*3) {
data_num = data_num + 1;
VALVE_POS_TMP = VALVE_POS_TMP + value;
} else if(VALVE_ID_timer == TMR_FREQ_5k*3) {
Vout.ref = 0.0f;
} else {
VALVE_POS_AVG[ID_index] = VALVE_POS_TMP / data_num;
VALVE_ID_timer = 0;
ID_index= ID_index +1;
}
if(ID_index>=25) {
int i;
VALVE_POS_AVG_OLD = VALVE_POS_AVG[0];
for(i=0; i<25; i++) {
VALVE_POS_VS_PWM[i] = (int16_t) (VALVE_POS_AVG[i]);
if(VALVE_POS_AVG[i] > VALVE_POS_AVG_OLD) {
VALVE_MAX_POS = VALVE_POS_AVG[i];
VALVE_POS_AVG_OLD = VALVE_MAX_POS;
} else if(VALVE_POS_AVG[i] < VALVE_POS_AVG_OLD) {
VALVE_MIN_POS = VALVE_POS_AVG[i];
VALVE_POS_AVG_OLD = VALVE_MIN_POS;
}
}
ROM_RESET_DATA();
ID_index = 0;
CONTROL_UTILITY_MODE = MODE_NO_ACT;
}
break;
}
case MODE_DDV_DEADZONE_AND_CENTER: {
CONTROL_MODE = MODE_VALVE_OPEN_LOOP;
VALVE_DZ_timer = VALVE_DZ_timer + 1;
if(first_check == 0) {
if(VALVE_DZ_timer < (int) (1.0f * (float) TMR_FREQ_5k)) {
Vout.ref = VALVE_VOLTAGE_LIMIT * 1000.0f;
} else if(VALVE_DZ_timer == (int) (1.0f * (float) TMR_FREQ_5k)) {
Vout.ref = VALVE_VOLTAGE_LIMIT * 1000.0f;
pos_plus_end = pos.sen;
} else if(VALVE_DZ_timer < (int) (2.0f * (float) TMR_FREQ_5k)) {
Vout.ref = -VALVE_VOLTAGE_LIMIT * 1000.0f;
} else if(VALVE_DZ_timer == (int) (2.0f * (float) TMR_FREQ_5k)) {
Vout.ref = -VALVE_VOLTAGE_LIMIT * 1000.0f;
pos_minus_end = pos.sen;
} else if(VALVE_DZ_timer < (int) (3.0f * (float) TMR_FREQ_5k)) {
Vout.ref = (float) P_GAIN_JOINT_POSITION * (0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end - (float) pos.sen)/(float) ENC_PULSE_PER_POSITION;
} else if(VALVE_DZ_timer < (int) (4.0f * (float) TMR_FREQ_5k)) {
Vout.ref = (float) P_GAIN_JOINT_POSITION * (0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end - (float) pos.sen)/(float) ENC_PULSE_PER_POSITION;
data_num = data_num + 1;
VALVE_POS_TMP = VALVE_POS_TMP + value;
} else if(VALVE_DZ_timer == (int) (4.0f * (float) TMR_FREQ_5k)) {
Vout.ref = (float) P_GAIN_JOINT_POSITION * (0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end - (float) pos.sen)/(float) ENC_PULSE_PER_POSITION;
DDV_POS_AVG = VALVE_POS_TMP / data_num;
START_POS = pos.sen;
VALVE_POS_TMP = 0;
data_num = 0;
} else if(VALVE_DZ_timer < (int) (5.0f * (float) TMR_FREQ_5k)) {
valve_pos.ref = DDV_POS_AVG;
VALVE_POS_CONTROL(valve_pos.ref);
} else if(VALVE_DZ_timer < (int) (6.0f * (float) TMR_FREQ_5k)) {
valve_pos.ref = DDV_POS_AVG;
VALVE_POS_CONTROL(valve_pos.ref);
} else if(VALVE_DZ_timer == (int) (6.0f * (float) TMR_FREQ_5k)) {
valve_pos.ref = DDV_POS_AVG;
VALVE_POS_CONTROL(valve_pos.ref);
FINAL_POS = pos.sen;
if((FINAL_POS - START_POS)>200) {
DZ_case = 1;
} else if((FINAL_POS - START_POS)<-200) {
DZ_case = -1;
} else {
DZ_case = 0;
}
CAN_TX_PRES((int16_t) (DZ_case), (int16_t) (6));
first_check = 1;
DZ_DIRECTION = 1;
VALVE_DZ_timer = 0;
Ref_Valve_Pos_Old = DDV_POS_AVG;
DZ_NUM = 1;
DZ_index = 1;
}
} else {
if((DZ_case == -1 && DZ_NUM == 1) | (DZ_case == 1 && DZ_NUM == 1)) {
if(VALVE_DZ_timer < (int) (1.0 * (float) TMR_FREQ_5k)) {
Vout.ref = (float) P_GAIN_JOINT_POSITION * (0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end - (float) pos.sen)/(float) ENC_PULSE_PER_POSITION;
//pos.ref = 0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end;
//CONTROL_MODE = MODE_JOINT_CONTROL;
} else if(VALVE_DZ_timer == (int) (1.0f * (float) TMR_FREQ_5k)) {
START_POS = pos.sen;
} else if(VALVE_DZ_timer < (int) (2.0f * (float) TMR_FREQ_5k)) {
valve_pos.ref = Ref_Valve_Pos_Old - DZ_case * DZ_DIRECTION * 64 / DZ_index;
if(valve_pos.ref <= VALVE_MIN_POS) {
valve_pos.ref = VALVE_MIN_POS;
} else if(valve_pos.ref >= VALVE_MAX_POS) {
valve_pos.ref = VALVE_MAX_POS;
}
VALVE_POS_CONTROL(valve_pos.ref);
} else if(VALVE_DZ_timer == (int) (2.0f * (float) TMR_FREQ_5k)) {
Ref_Valve_Pos_Old = valve_pos.ref;
FINAL_POS = pos.sen;
if((FINAL_POS - START_POS)>100) {
DZ_DIRECTION = 1 * DZ_case;
} else if((FINAL_POS - START_POS)<-100) {
DZ_DIRECTION = -1 * DZ_case;
} else {
DZ_DIRECTION = 1 * DZ_case;
}
VALVE_DZ_timer = 0;
DZ_index= DZ_index *2;
if(DZ_index >= 128) {
FIRST_DZ = valve_pos.ref;
DZ_NUM = 2;
Ref_Valve_Pos_Old = FIRST_DZ;
DZ_index = 1;
DZ_DIRECTION = 1;
}
}
} else if((DZ_case == -1 && DZ_NUM == 2) | (DZ_case == 1 && DZ_NUM == 2)) {
if(VALVE_DZ_timer < (int) (1.0f * (float) TMR_FREQ_5k)) {
Vout.ref = (float) P_GAIN_JOINT_POSITION * (0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end - (float) pos.sen)/(float) ENC_PULSE_PER_POSITION;
//pos.ref = 0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end;
//CONTROL_MODE = MODE_JOINT_CONTROL;
} else if(VALVE_DZ_timer == (int) (1.0f * (float) TMR_FREQ_5k)) {
START_POS = pos.sen;
} else if(VALVE_DZ_timer < (int) (2.0f * (float) TMR_FREQ_5k)) {
valve_pos.ref = Ref_Valve_Pos_Old - DZ_case * DZ_DIRECTION * 64 / DZ_index;
if(valve_pos.ref <= VALVE_MIN_POS) {
valve_pos.ref = VALVE_MIN_POS;
} else if(valve_pos.ref >= VALVE_MAX_POS) {
valve_pos.ref = VALVE_MAX_POS;
}
VALVE_POS_CONTROL(valve_pos.ref);
} else if(VALVE_DZ_timer == (int) (2.0f * (float) TMR_FREQ_5k)) {
Vout.ref = 0.0f;
} else if(VALVE_DZ_timer > (int) (2.0f * (float) TMR_FREQ_5k)) {
Ref_Valve_Pos_Old = valve_pos.ref;
FINAL_POS = pos.sen;
if((FINAL_POS - START_POS)>100) {
DZ_DIRECTION = 1 * DZ_case;
} else if((FINAL_POS - START_POS)<-100) {
DZ_DIRECTION = -1 * DZ_case;
} else {
DZ_DIRECTION = -1 * DZ_case;
}
VALVE_DZ_timer = 0;
DZ_index= DZ_index * 2;
if(DZ_index >= 128) {
SECOND_DZ = valve_pos.ref;
VALVE_CENTER = (int) (0.5f * (float) (FIRST_DZ) + 0.5f * (float) (SECOND_DZ));
first_check = 0;
VALVE_DEADZONE_MINUS = (float) FIRST_DZ;
VALVE_DEADZONE_PLUS = (float) SECOND_DZ;
ROM_RESET_DATA();
CONTROL_UTILITY_MODE = MODE_NO_ACT;
DZ_index = 1;
}
}
} else if(DZ_case == 0 && DZ_NUM ==1) {
if(VALVE_DZ_timer < (int) (1.0f * (float) TMR_FREQ_5k)) {
Vout.ref = (float) P_GAIN_JOINT_POSITION * (0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end - (float) pos.sen)/(float) ENC_PULSE_PER_POSITION;
//pos.ref = 0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end;
//CONTROL_MODE = MODE_JOINT_CONTROL;
} else if(VALVE_DZ_timer == (int) (1.0f * (float) TMR_FREQ_5k)) {
START_POS = pos.sen;
} else if(VALVE_DZ_timer < (int) (2.0f * (float) TMR_FREQ_5k)) {
valve_pos.ref = Ref_Valve_Pos_Old - DZ_DIRECTION * 64 / DZ_index;
if(valve_pos.ref <= VALVE_MIN_POS) {
valve_pos.ref = VALVE_MIN_POS;
} else if(valve_pos.ref >= VALVE_MAX_POS) {
valve_pos.ref = VALVE_MAX_POS;
}
VALVE_POS_CONTROL(valve_pos.ref);
} else if(VALVE_DZ_timer == (int) (2.0f * (float) TMR_FREQ_5k)) {
Ref_Valve_Pos_Old = valve_pos.ref;
FINAL_POS = pos.sen;
if((FINAL_POS - START_POS)>100) {
DZ_DIRECTION = 1;
} else if((FINAL_POS - START_POS)<-100) {
DZ_DIRECTION = -1;
} else {
DZ_DIRECTION = 1;
}
VALVE_DZ_timer = 0;
DZ_index= DZ_index *2;
if(DZ_index >= 128) {
FIRST_DZ = valve_pos.ref;
DZ_NUM = 2;
Ref_Valve_Pos_Old = FIRST_DZ;
DZ_index = 1;
DZ_DIRECTION = 1;
}
}
} else {
if(VALVE_DZ_timer < (int) (1.0f * (float) TMR_FREQ_5k)) {
Vout.ref = (float) P_GAIN_JOINT_POSITION * (0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end - (float) pos.sen)/(float) ENC_PULSE_PER_POSITION;
//pos.ref = 0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end;
//CONTROL_MODE = MODE_JOINT_CONTROL;
} else if(VALVE_DZ_timer == (int) (1.0f * (float) TMR_FREQ_5k)) {
START_POS = pos.sen;
} else if(VALVE_DZ_timer < (int) (2.0f * (float) TMR_FREQ_5k)) {
valve_pos.ref = Ref_Valve_Pos_Old + DZ_DIRECTION * 64 / DZ_index;
if(valve_pos.ref <= VALVE_MIN_POS) {
valve_pos.ref = VALVE_MIN_POS;
} else if(valve_pos.ref > VALVE_MAX_POS) {
valve_pos.ref = VALVE_MAX_POS - 1;
}
VALVE_POS_CONTROL(valve_pos.ref);
} else if(VALVE_DZ_timer == (int) (2.0f * (float) TMR_FREQ_5k)) {
Vout.ref = 0.0f;
} else if(VALVE_DZ_timer > (int) (2.0f * (float) TMR_FREQ_5k)) {
Ref_Valve_Pos_Old = valve_pos.ref;
FINAL_POS = pos.sen;
if((FINAL_POS - START_POS)>100) {
DZ_DIRECTION = 1;
} else if((FINAL_POS - START_POS)<-100) {
DZ_DIRECTION = -1;
} else {
DZ_DIRECTION = 1;
}
VALVE_DZ_timer = 0;
DZ_index= DZ_index *2;
if(DZ_index >= 128) {
SECOND_DZ = valve_pos.ref;
VALVE_CENTER = (int) (0.5f * (float) (FIRST_DZ) + 0.5f * (float) (SECOND_DZ));
first_check = 0;
VALVE_DEADZONE_MINUS = (float) FIRST_DZ;
VALVE_DEADZONE_PLUS = (float) SECOND_DZ;
ROM_RESET_DATA();
CONTROL_UTILITY_MODE = MODE_NO_ACT;
DZ_index = 1;
}
}
}
}
break;
}
case MODE_DDV_POS_VS_FLOWRATE: {
CONTROL_MODE = MODE_VALVE_OPEN_LOOP;
VALVE_FR_timer = VALVE_FR_timer + 1;
if(first_check == 0) {
if(VALVE_FR_timer < (int) (1.0f * (float) TMR_FREQ_5k)) {
Vout.ref = VALVE_VOLTAGE_LIMIT * 1000.0f;
//CAN_TX_PRES((int16_t) (VALVE_FR_timer), (int16_t) (6));
} else if(VALVE_FR_timer == (int) (1.0f * (float) TMR_FREQ_5k)) {
Vout.ref = VALVE_VOLTAGE_LIMIT * 1000.0f;
pos_plus_end = pos.sen;
// CAN_TX_PRES((int16_t) (V_out), (int16_t) (7));
} else if(VALVE_FR_timer < (int) (2.0f * (float) TMR_FREQ_5k)) {
Vout.ref = -VALVE_VOLTAGE_LIMIT * 1000.0f;
} else if(VALVE_FR_timer == (int) (2.0f * (float) TMR_FREQ_5k)) {
// CAN_TX_PRES((int16_t) (V_out), (int16_t) (8));
Vout.ref = -VALVE_VOLTAGE_LIMIT * 1000.0f;
pos_minus_end = pos.sen;
first_check = 1;
VALVE_FR_timer = 0;
valve_pos.ref = (float) VALVE_CENTER;
ID_index = 0;
max_check = 0;
min_check = 0;
}
} else {
if(VALVE_FR_timer < (int) (1.0f * (float) TMR_FREQ_5k)) {
//V_out = (float) P_GAIN_JOINT_POSITION * (0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end - (float) pos.sen)/(float) ENC_PULSE_PER_POSITION;
pos.ref = 0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end;
CONTROL_MODE = MODE_JOINT_CONTROL;
} else if(VALVE_FR_timer == (int) (1.0f * (float) TMR_FREQ_5k)) {
data_num = 0;
valve_pos.ref = 10.0f*((float) ID_index_array[ID_index]) + (float) VALVE_CENTER;
VALVE_POS_CONTROL(valve_pos.ref);
START_POS = pos.sen;
} else if(VALVE_FR_timer < (int) (5.0f * (float) TMR_FREQ_5k)) {
valve_pos.ref = 10.0f*((float) ID_index_array[ID_index]) + (float) VALVE_CENTER;
VALVE_POS_CONTROL(valve_pos.ref);
data_num = data_num + 1;
if(abs(0.5f * (float) pos_plus_end + 0.5f * (float) pos_minus_end - (float) pos.sen) > 20000.0f) {
FINAL_POS = pos.sen;
one_period_end = 1;
}
} else if(VALVE_FR_timer == (int) (5.0f * (float) TMR_FREQ_5k)) {
FINAL_POS = pos.sen;
one_period_end = 1;
V_out = 0.0f;
}
if(one_period_end == 1) {
if(valve_pos.ref > VALVE_MAX_POS) {
max_check = 1;
} else if(valve_pos.ref < VALVE_MIN_POS) {
min_check = 1;
}
JOINT_VEL[ID_index] = (FINAL_POS - START_POS) / data_num * TMR_FREQ_5k; // pulse/sec
VALVE_FR_timer = 0;
one_period_end = 0;
ID_index= ID_index +1;
V_out = 0.0f;
}
if(max_check == 1 && min_check == 1) {
VALVE_POS_NUM = ID_index;
ROM_RESET_DATA();
ID_index = 0;
first_check = 0;
VALVE_FR_timer = 0;
CONTROL_UTILITY_MODE = MODE_NO_ACT;
// CAN_TX_PRES((int16_t) (VALVE_FR_timer), (int16_t) (6));
}
}
break;
}
case MODE_SYSTEM_ID: {
freq_sysid_Iref = (double) cnt_sysid * DT_TMR3 * 3.;
valve_pos.ref = 2500.0f * sin(2.0f * 3.14159f * freq_sysid_Iref * (double) cnt_sysid * DT_TMR3);
CONTROL_MODE = MODE_VALVE_OPEN_LOOP;
cnt_sysid++;
if (freq_sysid_Iref >= 300) {
cnt_sysid = 0;
CONTROL_UTILITY_MODE = MODE_NO_ACT;
}
break;
}
default:
break;
}
// CONTROL MODE ------------------------------------------------------------
switch (CONTROL_MODE) {
case MODE_NO_ACT: {
V_out = 0.0f;
break;
}
case MODE_VALVE_POSITION_CONTROL: {
if (OPERATING_MODE == 5) { //SW Valve
VALVE_POS_CONTROL(valve_pos.ref);
V_out = Vout.ref;
} else if (CURRENT_CONTROL_MODE == 0) { //PWM
V_out = valve_pos.ref;
} else {
I_REF = valve_pos.ref * 0.001f;
}
break;
}
case MODE_JOINT_CONTROL: {
double torq_ref = 0.0f;
pos.err = (pos.ref - pos.sen)/(float)(ENC_PULSE_PER_POSITION); //[mm]
vel.err = (0.0f - vel.sen)/(float)(ENC_PULSE_PER_POSITION); //[mm/s]
pos.err_sum += pos.err/(float) TMR_FREQ_5k; //[mm]
//K & D Low Pass Filter
float alpha_K_D = 1.0f/(1.0f + 5000.0f/(2.0f*3.14f*30.0f)); // f_cutoff : 30Hz
K_LPF = K_LPF*(1.0f-alpha_K_D)+K_SPRING*(alpha_K_D);
D_LPF = D_LPF*(1.0f-alpha_K_D)+D_DAMPER*(alpha_K_D);
// torq_ref = torq.ref + K_LPF * pos.err - D_LPF * vel.sen / ENC_PULSE_PER_POSITION; //[N]
torq_ref = torq.ref;
// torque feedback
torq.err = torq_ref - torq.sen; //[N]
torq.err_sum += torq.err/(float) TMR_FREQ_5k; //[N]
if (((OPERATING_MODE&0b110)>>1) == 0 || ((OPERATING_MODE&0b110)>>1) == 1) {
double I_REF_POS = 0.0f;
double I_REF_FORCE_FB = 0.0f; // I_REF by Force Feedback
double I_REF_VC = 0.0f; // I_REF for velocity compensation
double temp_vel_pos = 0.0f;
double temp_vel_torq = 0.0f;
double wn_Pos = 2.0f * PI * 5.0f; // f_cut : 5Hz Position Control
if ((OPERATING_MODE & 0x01) == 0) { // Rotary Mode
temp_vel_pos = (0.01f * (double) P_GAIN_JOINT_POSITION * wn_Pos * pos.err + 0.01f * (double) I_GAIN_JOINT_POSITION * wn_Pos * pos.err_sum + 0.01f * (double) VELOCITY_COMP_GAIN * vel.ref / ENC_PULSE_PER_POSITION) * PI / 180.0f; // rad/s
// L when P-gain = 100, f_cut = 10Hz L feedforward velocity
} else if ((OPERATING_MODE & 0x01) == 1) {
temp_vel_pos = (0.01f * (double) P_GAIN_JOINT_POSITION * wn_Pos * pos.err + 0.01f * (double) I_GAIN_JOINT_POSITION * wn_Pos * pos.err_sum + 0.01f * (double) VELOCITY_COMP_GAIN * vel.ref / ENC_PULSE_PER_POSITION); // mm/s
// L when P-gain = 100, f_cut = 10Hz L feedforward velocity
}
if (temp_vel_pos > 0.0f) I_REF_POS = temp_vel_pos * ((double) PISTON_AREA_A * 0.00006f / (K_v * sqrt(2.0f * alpha3 / (alpha3 + 1.0f))));
else I_REF_POS = temp_vel_pos * ((double) PISTON_AREA_B * 0.00006f / (K_v * sqrt(2.0f / (alpha3 + 1.0f))));
// velocity compensation for torque control
if ((OPERATING_MODE & 0x01) == 0) { // Rotary Mode
I_REF_FORCE_FB = 0.001f * ((double) P_GAIN_JOINT_TORQUE * torq.err + (double) I_GAIN_JOINT_TORQUE * torq.err_sum);
// temp_vel_torq = (0.01 * (double) VELOCITY_COMP_GAIN * (double) CUR_VELOCITY / (double) ENC_PULSE_PER_POSITION) * PI / 180.0; // rad/s
temp_vel_torq = (0.01f * (double) VELOCITY_COMP_GAIN * vel.ref / (double) ENC_PULSE_PER_POSITION) * PI / 180.0f; // rad/s
// L feedforward velocity
} else if ((OPERATING_MODE & 0x01) == 1) {
I_REF_FORCE_FB = 0.001f * 0.01f*((double) P_GAIN_JOINT_TORQUE * torq.err + (double) I_GAIN_JOINT_TORQUE * torq.err_sum); // Linear Actuators are more sensitive.
// temp_vel_torq = (0.01 * (double) VELOCITY_COMP_GAIN * (double) CUR_VELOCITY / (double) ENC_PULSE_PER_POSITION); // mm/s
temp_vel_torq = (0.01f * (double) VELOCITY_COMP_GAIN * vel.ref / (double) ENC_PULSE_PER_POSITION); // mm/s
// L feedforward velocity
}
if (temp_vel_torq > 0.0f) I_REF_VC = temp_vel_torq * ((double) PISTON_AREA_A * 0.00006f / (K_v * sqrt(2.0f * alpha3 / (alpha3 + 1.0f))));
else I_REF_VC = temp_vel_torq * ((double) PISTON_AREA_B * 0.00006f / (K_v * sqrt(2.0f / (alpha3 + 1.0f))));
// L velocity(rad/s or mm/s) >> I_ref(mA)
// Ref_Joint_FT_dot = (Ref_Joint_FT_Nm - Ref_Joint_FT_Nm_old) / TMR_DT_5k;
// Ref_Joint_FT_Nm_old = Ref_Joint_FT_Nm;
I_REF = (1.0f - alpha_trans) * I_REF_POS + alpha_trans * (I_REF_VC + I_REF_FORCE_FB);
// Anti-windup for FT
if (I_GAIN_JOINT_TORQUE != 0) {
double I_MAX = 10.0f; // Maximum Current : 10mV
double Ka = 2.0f / ((double) I_GAIN_JOINT_TORQUE * 0.001f);
if (I_REF > I_MAX) {
double I_rem = I_REF - I_MAX;
I_rem = Ka*I_rem;
I_REF = I_MAX;
torq.err_sum = torq.err_sum - I_rem /(float) TMR_FREQ_5k;
} else if (I_REF < -I_MAX) {
double I_rem = I_REF - (-I_MAX);
I_rem = Ka*I_rem;
I_REF = -I_MAX;
torq.err_sum = torq.err_sum - I_rem /(float) TMR_FREQ_5k;
}
}
} else {
float VALVE_POS_RAW_FORCE_FB = 0.0f;
float VALVE_POS_RAW_FORCE_FF = 0.0f;
float VALVE_POS_RAW = 0.0f;
VALVE_POS_RAW_FORCE_FB = alpha_trans*(((float) P_GAIN_JOINT_TORQUE * torq.err + (float) I_GAIN_JOINT_TORQUE * torq.err_sum) * 0.01f
+ DDV_JOINT_POS_FF(vel.sen))+ (1.0f-alpha_trans) * (P_GAIN_JOINT_POSITION * 0.01f * pos.err + DDV_JOINT_POS_FF(vel.ref));
VALVE_POS_RAW_FORCE_FF = P_GAIN_JOINT_TORQUE_FF * torq_ref * 0.001f + D_GAIN_JOINT_TORQUE_FF * (torq_ref - torq_ref_past) * 0.0001f;
VALVE_POS_RAW = VALVE_POS_RAW_FORCE_FB + VALVE_POS_RAW_FORCE_FF;
if (VALVE_POS_RAW >= 0) {
valve_pos.ref = VALVE_POS_RAW + VALVE_DEADZONE_PLUS;
} else {
valve_pos.ref = VALVE_POS_RAW + VALVE_DEADZONE_MINUS;
}
if(I_GAIN_JOINT_TORQUE != 0) {
double Ka = 2.0f / (double) I_GAIN_JOINT_TORQUE * 100.0f;
if(valve_pos.ref>VALVE_MAX_POS) {
double valve_pos_rem = valve_pos.ref - VALVE_MAX_POS;
valve_pos_rem = valve_pos_rem * Ka;
valve_pos.ref = VALVE_MAX_POS;
torq.err_sum = torq.err_sum - valve_pos_rem/(float) TMR_FREQ_5k;
} else if(valve_pos.ref < VALVE_MIN_POS) {
double valve_pos_rem = valve_pos.ref - VALVE_MIN_POS;
valve_pos_rem = valve_pos_rem * Ka;
valve_pos.ref = VALVE_MIN_POS;
torq.err_sum = torq.err_sum - valve_pos_rem/(float) TMR_FREQ_5k;
}
}
VALVE_POS_CONTROL(valve_pos.ref);
// Vout.ref = (float) P_GAIN_JOINT_POSITION * 0.01f * ((float) pos.err);
V_out = (float) Vout.ref;
}
torq_ref_past = torq_ref;
break;
}
case MODE_VALVE_OPEN_LOOP: {
V_out = (float) Vout.ref;
break;
}
case MODE_JOINT_ADAPTIVE_BACKSTEPPING: {
float Va = (1256.6f + Amm * pos.sen/(float)(ENC_PULSE_PER_POSITION)) * 0.000000001f; // 4mm pipe * 100mm + (25mm Cylinder 18mm Rod) * x, unit : m^3
float Vb = (1256.6f + Amm * (79.0f - pos.sen/(float)(ENC_PULSE_PER_POSITION))) * 0.000000001f; // 4mm pipe * 100mm + (25mm Cylinder 18mm Rod) * (79.0mm-x), unit : m^3
// float Va = (1256.6f + Amm * 39.5f) * 0.000000001f; // 4mm pipe * 100mm + (25mm Cylinder 18mm Rod) * x, unit : m^3
// float Vb = (1256.6f + Amm * 39.5f) * 0.000000001f; // 4mm pipe * 100mm + (25mm Cylinder 18mm Rod) * (79.0mm-x), unit : m^3
V = 1.0f / (1.0f/Va + 1.0f/Vb); //initial 0.0000053f
float f3 = -Amm*Amm*beta*0.000001f*0.000001f/V * vel.sen/(float)(ENC_PULSE_PER_POSITION)*0.001f; // unit : N/s //xdot=10mm/s일때 -137076
float g3_prime = 0.0f;
if (torq.sen > Amm*(Ps-Pt)*0.000001f){
g3_prime = 1.0f;
} else if (torq.sen < -Amm*(Ps-Pt)*0.000001f) {
g3_prime = -1.0f;
} else {
if ((value-VALVE_CENTER) > 0) {
g3_prime = sqrt(Ps-Pt-torq.sen/Amm*1000000.0f);
// g3_prime = sqrt(Ps-Pt);
} else {
g3_prime = sqrt(Ps-Pt+torq.sen/Amm*1000000.0f);
// g3_prime = sqrt(Ps-Pt);
}
}
float tau = 0.01f;
float K_valve = 0.0004f;
float x_v = 0.0f; //x_v : -1~1
if(value>=VALVE_CENTER) {
x_v = 1.0f*((double)value - (double)VALVE_CENTER)/((double)VALVE_MAX_POS - (double)VALVE_CENTER);
} else {
x_v = -1.0f*((double)value - (double)VALVE_CENTER)/((double)VALVE_MIN_POS - (double)VALVE_CENTER);
}
float f4 = -x_v/tau;
float g4 = K_valve/tau;
float torq_ref_dot = torq.ref_diff * 500.0f;
pos.err = (pos.ref - pos.sen)/(float)(ENC_PULSE_PER_POSITION); //[mm]
vel.err = (0.0f - vel.sen)/(float)(ENC_PULSE_PER_POSITION); //[mm/s]
pos.err_sum += pos.err/(float) TMR_FREQ_5k; //[mm]
torq.err = torq.ref - torq.sen; //[N]
torq.err_sum += torq.err/(float) TMR_FREQ_5k; //[N]
float k3 = 20000.0f; //2000
float k4 = 10.0f;
float rho3 = 3.2f;
float rho4 = 25000000.0f;
float x_4_des = (-f3 + torq_ref_dot - k3*(-torq.err))/(gamma_hat*g3_prime);
if (x_4_des > 1) x_4_des = 1;
else if (x_4_des < -1) x_4_des = -1;
if (x_4_des > 0) {
valve_pos.ref = x_4_des * (float)(VALVE_MAX_POS - VALVE_CENTER) + (float) VALVE_CENTER;
} else {
valve_pos.ref = x_4_des * (float)(VALVE_CENTER - VALVE_MIN_POS) + (float) VALVE_CENTER;
}
float x_4_des_dot = (x_4_des - x_4_des_old)*(float) TMR_FREQ_5k;
x_4_des_old = x_4_des;
V_out = (-f4 + x_4_des_dot - k4*(x_v-x_4_des)- rho3/rho4*gamma_hat*g3_prime*(-torq.err))/g4;
float rho_gamma = 50000.0f;//5000
float gamma_hat_dot = rho3*(-torq.err)/rho_gamma*((-f3+torq_ref_dot-k3*(-torq.err))/gamma_hat + g3_prime*(x_v-x_4_des));
gamma_hat = gamma_hat + gamma_hat_dot / (float) TMR_FREQ_5k;
break;
}
default:
break;
}
if (((OPERATING_MODE&0b110)>>1) == 0 || ((OPERATING_MODE&0b110)>>1) == 1) { //Moog Valve or KNR Valve
////////////////////////////////////////////////////////////////////////////
//////////////////////////// CURRENT CONTROL //////////////////////////////
////////////////////////////////////////////////////////////////////////////
if (CURRENT_CONTROL_MODE) {
double alpha_update_Iref = 1.0f / (1.0f + 5000.0f / (2.0f * 3.14f * 300.0f)); // f_cutoff : 500Hz
I_REF_fil = (1.0f - alpha_update_Iref) * I_REF_fil + alpha_update_Iref*I_REF;
I_ERR = I_REF_fil - cur.sen;
I_ERR_INT = I_ERR_INT + (I_ERR) * 0.0002f;
// Moog Valve Current Control Gain
double R_model = 500.0f; // ohm
double L_model = 1.2f;
double w0 = 2.0f * 3.14f * 150.0f;
double KP_I = 0.1f * L_model*w0;
double KI_I = 0.1f * R_model*w0;
// KNR Valve Current Control Gain
if (((OPERATING_MODE & 0b110)>>1) == 1) { // KNR Valve
R_model = 163.0f; // ohm
L_model = 1.0f;
w0 = 2.0f * 3.14f * 80.0f;
KP_I = 1.0f * L_model*w0;
KI_I = 0.08f * R_model*w0;
}
double FF_gain = 1.0f;
VALVE_PWM_RAW = KP_I * 2.0f * I_ERR + KI_I * 2.0f* I_ERR_INT;
// VALVE_PWM_RAW = VALVE_PWM_RAW + FF_gain * (R_model*I_REF); // Unit : mV
I_REF_fil_diff = I_REF_fil - I_REF_fil_old;
I_REF_fil_old = I_REF_fil;
// VALVE_PWM_RAW = VALVE_PWM_RAW + FF_gain * (R_model * I_REF_fil + L_model * I_REF_fil_diff * 5000.0f); // Unit : mV
VALVE_PWM_RAW = VALVE_PWM_RAW + FF_gain * (R_model * I_REF_fil); // Unit : mV
double V_MAX = 12000.0f; // Maximum Voltage : 12V = 12000mV
double Ka = 3.0f / KP_I;
if (VALVE_PWM_RAW > V_MAX) {
V_rem = VALVE_PWM_RAW - V_MAX;
V_rem = Ka*V_rem;
VALVE_PWM_RAW = V_MAX;
I_ERR_INT = I_ERR_INT - V_rem * 0.0002f;
} else if (VALVE_PWM_RAW < -V_MAX) {
V_rem = VALVE_PWM_RAW - (-V_MAX);
V_rem = Ka*V_rem;
VALVE_PWM_RAW = -V_MAX;
I_ERR_INT = I_ERR_INT - V_rem * 0.0002f;
}
Cur_Valve_Open_pulse = cur.sen / mA_PER_pulse;
} else {
VALVE_PWM_RAW = I_REF * mV_PER_mA;
Cur_Valve_Open_pulse = I_REF / mA_PER_pulse;
}
////////////////////////////////////////////////////////////////////////////
///////////////// Dead Zone Cancellation & Linearization //////////////////
////////////////////////////////////////////////////////////////////////////
// Dead Zone Cancellation (Mechanical Valve dead-zone)
if (FLAG_VALVE_DEADZONE) {
if (VALVE_PWM_RAW > 0) VALVE_PWM_RAW = VALVE_PWM_RAW + VALVE_DEADZONE_PLUS * mV_PER_pulse; // unit: mV
else if (VALVE_PWM_RAW < 0) VALVE_PWM_RAW = VALVE_PWM_RAW + VALVE_DEADZONE_MINUS * mV_PER_pulse; // unit: mV
VALVE_PWM_VALVE_DZ = VALVE_PWM_RAW + (double)VALVE_CENTER * mV_PER_pulse; // unit: mV
} else {
VALVE_PWM_VALVE_DZ = VALVE_PWM_RAW;
}
// Output Voltage Linearization
double CUR_PWM_nonlin = VALVE_PWM_VALVE_DZ; // Unit : mV
double CUR_PWM_lin = PWM_duty_byLT(CUR_PWM_nonlin); // -8000~8000
// Dead Zone Cancellation (Electrical dead-zone)
if (CUR_PWM_lin > 0) V_out = (float) (CUR_PWM_lin + 169.0f);
else if (CUR_PWM_lin < 0) V_out = (float) (CUR_PWM_lin - 174.0f);
else V_out = (float) (CUR_PWM_lin);
}
else { //////////////////////////sw valve
// Output Voltage Linearization
// double CUR_PWM_nonlin = V_out; // Unit : mV
// double CUR_PWM_lin = PWM_duty_byLT(CUR_PWM_nonlin); // -8000~8000
// Dead Zone Cancellation (Electrical dead-zone)
// if (CUR_PWM_lin > 0) V_out = (float) (CUR_PWM_lin + 169.0f);
// else if (CUR_PWM_lin < 0) V_out = (float) (CUR_PWM_lin - 174.0f);
// else V_out = (float) (CUR_PWM_lin);
if (V_out > 0 ) V_out = (V_out + 180.0f)/0.8588f;
else if (V_out < 0) V_out = (V_out - 200.0f)/0.8651f;
else V_out = 0.0f;
}
// if(V_out > 0.0f) V_out = (float) (V_out + 169.0f);
// else if(V_out < 0.0f) V_out = (float) (V_out - 174.0f);
// else V_out = V_out;
/*******************************************************
*** PWM
********************************************************/
if(DIR_VALVE<0){
V_out = -V_out;
}
if (V_out >= VALVE_VOLTAGE_LIMIT*1000.0f) {
V_out = VALVE_VOLTAGE_LIMIT*1000.0f;
} else if(V_out<=-VALVE_VOLTAGE_LIMIT*1000.0f) {
V_out = -VALVE_VOLTAGE_LIMIT*1000.0f;
}
PWM_out= V_out/(SUPPLY_VOLTAGE*1000.0f); // Full duty : 12000.0mV
// Saturation of output voltage to 12.0V
if(PWM_out > 1.0f) PWM_out=1.0f;
else if (PWM_out < -1.0f) PWM_out=-1.0f;
if (PWM_out>0.0f) {
dtc_v=0.0f;
dtc_w=PWM_out;
} else {
dtc_v=-PWM_out;
dtc_w=0.0f;
}
//pwm
TIM4->CCR2 = (PWM_ARR)*(1.0f-dtc_v);
TIM4->CCR1 = (PWM_ARR)*(1.0f-dtc_w);
if (TMR2_COUNT_CAN_TX % (int) ((int) TMR_FREQ_5k/CAN_FREQ) == 0) {
// Position, Velocity, and Torque (ID:1200)
if (flag_data_request[0] == HIGH) {
if ((OPERATING_MODE & 0b01) == 0) { // Rotary Actuator
if (SENSING_MODE == 0) {
CAN_TX_POSITION_FT((int16_t) (pos.sen), (int16_t) (vel.sen/10.0f), (int16_t) (torq.sen*10.0f));
} else if (SENSING_MODE == 1) {
CAN_TX_POSITION_PRESSURE((int16_t) (pos.sen), (int16_t) (vel.sen/10.0f), (int16_t) ((pres_A.sen)*5.0f), (int16_t) ((pres_B.sen)*5.0f));
}
} else if ((OPERATING_MODE & 0b01) == 1) { // Linear Actuator
if (SENSING_MODE == 0) {
CAN_TX_POSITION_FT((int16_t) (pos.sen/10.0f), (int16_t) (vel.sen/256.0f), (int16_t) (torq.sen * 10.0f * (float)(TORQUE_SENSOR_PULSE_PER_TORQUE)));
} else if (SENSING_MODE == 1) {
CAN_TX_POSITION_PRESSURE((int16_t) (pos.sen/10.0f), (int16_t) (vel.sen/256.0f), (int16_t) ((pres_A.sen)*5.0f), (int16_t) ((pres_B.sen)*5.0f));
}
}
}
if (flag_data_request[1] == HIGH) {
//valve position
double t_value = 0;
if(valve_pos.ref>=(float) VALVE_CENTER) {
t_value = 10000.0f*((double)valve_pos.ref - (double)VALVE_CENTER)/((double)VALVE_MAX_POS - (double)VALVE_CENTER);
} else {
t_value = -10000.0f*((double)valve_pos.ref - (double)VALVE_CENTER)/((double)VALVE_MIN_POS - (double)VALVE_CENTER);
}
// if(OPERATING_MODE==5) {
// if(valve_pos.ref>=(float) VALVE_CENTER) {
// t_value = 10000.0f*((double)value - (double)VALVE_CENTER)/((double)VALVE_MAX_POS - (double)VALVE_CENTER);
// } else {
// t_value = -10000.0f*((double)value - (double)VALVE_CENTER)/((double)VALVE_MIN_POS - (double)VALVE_CENTER);
// }
//t_value = (double) value;
// } else if(CURRENT_CONTROL_MODE==1) {
// t_value = cur.sen * 1000.0f;
// } else {
// t_value = V_out;
// }
CAN_TX_TORQUE((int16_t) (t_value)); //1300
//CAN_TX_TORQUE((int16_t) (cur.sen * 1000.0f)); //1300
//CAN_TX_TORQUE((int16_t) (I_REF * 1000.0f)); //1300
}
if (flag_data_request[2] == LOW) {
//CAN_TX_PRES((int16_t) (pres_A.sen), (int16_t) (pres_B.sen)); // 1400
double t_value = 0;
if(valve_pos.ref>=(float) VALVE_CENTER) {
t_value = 10000.0f*((double)value - (double)VALVE_CENTER)/((double)VALVE_MAX_POS - (double)VALVE_CENTER);
} else {
t_value = -10000.0f*((double)value - (double)VALVE_CENTER)/((double)VALVE_MIN_POS - (double)VALVE_CENTER);
}
CAN_TX_PRES((int16_t) (t_value), (int16_t) (torq.ref)); // 1400
}
//If it doesn't rest, below can can not work.
for (can_rest = 0; can_rest < 10000; can_rest++) {
;
}
if (flag_data_request[3] == LOW) {
//PWM
//CAN_TX_PWM((int16_t) value); //1500
CAN_TX_PWM((int16_t) gamma_hat); //1500
}
//for (i = 0; i < 10000; i++) {
// ;
// }
if (flag_data_request[4] == HIGH) {
//valve position
CAN_TX_VALVE_POSITION((int16_t) (input_NN[1] * 100.0f), (int16_t) (input_NN[2]* 100.0f), (int16_t) (input_NN[3]* 100.0f), (int16_t) (input_NN[4]* 100.0f)); //1600
}
// Others : Reference position, Reference FT, PWM, Current (ID:1300)
// if (flag_data_request[1] == HIGH) {
// CAN_TX_SOMETHING((int) (FORCE_VREF), (int16_t) (1), (int16_t) (2), (int16_t) (3));
// }
//if (flag_delay_test == 1){
//CAN_TX_PRES((int16_t) (0),(int16_t) torq_ref);
//}
TMR2_COUNT_CAN_TX = 0;
}
TMR2_COUNT_CAN_TX++;
}
TIM3->SR = 0x0; // reset the status register
}