Diff: targets/hal/TARGET_Silicon_Labs/TARGET_EFM32/TARGET_EFM32WG_STK3800/PinNames.h

Revision:

144:ef7eb2e8f9f7

Parent:

0:9b334a45a8ff

diff -r 423e1876dc07 -r ef7eb2e8f9f7 targets/hal/TARGET_Silicon_Labs/TARGET_EFM32/TARGET_EFM32WG_STK3800/PinNames.h
--- a/targets/hal/TARGET_Silicon_Labs/TARGET_EFM32/TARGET_EFM32WG_STK3800/PinNames.h	Tue Aug 02 14:07:36 2016 +0000
+++ b/targets/hal/TARGET_Silicon_Labs/TARGET_EFM32/TARGET_EFM32WG_STK3800/PinNames.h	Fri Sep 02 15:07:44 2016 +0100
@@ -1,126 +1,119 @@
-/***************************************************************************//**
- * @file PinNames.h
- *******************************************************************************
- * @section License
- * <b>(C) Copyright 2015 Silicon Labs, http://www.silabs.com</b>
- *******************************************************************************
- *
- * Permission is granted to anyone to use this software for any purpose,
- * including commercial applications, and to alter it and redistribute it
- * freely, subject to the following restrictions:
- *
- * 1. The origin of this software must not be misrepresented; you must not
- *    claim that you wrote the original software.
- * 2. Altered source versions must be plainly marked as such, and must not be
- *    misrepresented as being the original software.
- * 3. This notice may not be removed or altered from any source distribution.
- *
- * DISCLAIMER OF WARRANTY/LIMITATION OF REMEDIES: Silicon Labs has no
- * obligation to support this Software. Silicon Labs is providing the
- * Software "AS IS", with no express or implied warranties of any kind,
- * including, but not limited to, any implied warranties of merchantability
- * or fitness for any particular purpose or warranties against infringement
- * of any proprietary rights of a third party.
- *
- * Silicon Labs will not be liable for any consequential, incidental, or
- * special damages, or any other relief, or for any claim by any third party,
- * arising from your use of this Software.
- *
- ******************************************************************************/
-#ifndef MBED_PINNAMES_H
-#define MBED_PINNAMES_H
-
-#include "cmsis.h"
-#include "em_gpio.h"
-
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-typedef enum {
-    PIN_INPUT = 0,
-    PIN_OUTPUT = 1
-} PinDirection;
-
-typedef enum {
-    /* EFM32 Pin Names
-     * First 4 bits represent pin number, the remaining
-     * bits represent port number (A = 0, B = 1, ...)
-     */
-    PA0 = 0 << 4, PA1, PA2, PA3, PA4, PA5, PA6, PA7, PA8, PA9, PA10, PA11, PA12, PA13, PA14, PA15,
-    PB0 = 1 << 4, PB1, PB2, PB3, PB4, PB5, PB6, PB7, PB8, PB9, PB10, PB11, PB12, PB13, PB14, PB15,
-    PC0 = 2 << 4, PC1, PC2, PC3, PC4, PC5, PC6, PC7, PC8, PC9, PC10, PC11, PC12, PC13, PC14, PC15,
-    PD0 = 3 << 4, PD1, PD2, PD3, PD4, PD5, PD6, PD7, PD8, PD9, PD10, PD11, PD12, PD13, PD14, PD15,
-    PE0 = 4 << 4, PE1, PE2, PE3, PE4, PE5, PE6, PE7, PE8, PE9, PE10, PE11, PE12, PE13, PE14, PE15,
-    PF0 = 5 << 4, PF1, PF2, PF3, PF4, PF5, PF6, PF7, PF8, PF9, PF10, PF11, PF12, PF13, PF14, PF15,
-
-    /* Starter Kit says LED0 and LED1, but mbed expects 1 and 2. This way using 1 and 2 or 0 and 1 will work. */
-    LED0 = PE2,
-    LED1 = PE3,
-    LED2 = LED0,
-    LED3 = LED0,
-    LED4 = LED1,
-
-    /* Push Buttons */
-    SW0 = PB9,
-    SW1 = PB10,
-    BTN0 = SW0,
-    BTN1 = SW1,
-
-    /* Serial */
-    SERIAL_TX   = PD0,
-    SERIAL_RX   = PD1,
-    USBTX       = PE0,
-    USBRX       = PE1,
-    EFM_BC_EN   = PF7,
-
-    /* Not connected */
-    NC = (int) 0xFFFFFFFF
-} PinName;
-
-
-/* 0x10 represents setting the DOUT register (see efm32 modes in ref. manual) */
-typedef enum {
-    /* EFM32 pin modes */
-    Disabled        = gpioModeDisabled,
-    DisabledPullUp  = gpioModeDisabled | 0x10,
-    Input 			= gpioModeInput,
-    InputFilter 	= gpioModeInput | 0x10,
-    InputPullDown 	= gpioModeInputPull,
-    InputPullUp     = gpioModeInputPull | 0x10,
-    InputPullFilterDown = gpioModeInputPullFilter,
-    InputPullFilterUp 	= gpioModeInputPullFilter | 0x10,
-    PushPull 		= gpioModePushPull,
-    PushPullDrive 	= gpioModePushPullDrive,
-    WiredOr 		= gpioModeWiredOr,
-    WiredOrPullDown = gpioModeWiredOrPullDown,
-    WiredAnd 		= gpioModeWiredAnd,
-    WiredAndFilter 	= gpioModeWiredAndFilter,
-    WiredAndPullUp 	= gpioModeWiredAndPullUp,
-    WiredAndPullUpFilter = gpioModeWiredAndPullUpFilter,
-    WiredAndDrive 		= gpioModeWiredAndDrive,
-    WiredAndDriveFilter	= gpioModeWiredAndDriveFilter,
-    WiredAndDrivePullUp	= gpioModeWiredAndDrivePullUp,
-    WiredAndDrivePullUpFilter = gpioModeWiredAndDrivePullUpFilter,
-
-    /* mbed modes:
-     * PullUp, PullDown, PullNone, OpenDrain
-     *
-     * mbed default digital input mode:
-     * PullDefault
-     *
-     * mbed default digital output mode:
-     * PullNone
-     */
-    PullUp = InputPullUp,
-    PullDown = InputPullDown,
-    OpenDrain = WiredAnd,
-    PullNone = PushPull,
-    PullDefault = PushPull
-} PinMode;
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif
+/***************************************************************************//**
+ * @file PinNames.h
+ *******************************************************************************
+ * @section License
+ * <b>(C) Copyright 2015 Silicon Labs, http://www.silabs.com</b>
+ *******************************************************************************
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License"); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ *
+ ******************************************************************************/
+#ifndef MBED_PINNAMES_H
+#define MBED_PINNAMES_H
+
+#include "cmsis.h"
+#include "em_gpio.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+typedef enum {
+    PIN_INPUT = 0,
+    PIN_OUTPUT = 1
+} PinDirection;
+
+typedef enum {
+    /* EFM32 Pin Names
+     * First 4 bits represent pin number, the remaining
+     * bits represent port number (A = 0, B = 1, ...)
+     */
+    PA0 = 0 << 4, PA1, PA2, PA3, PA4, PA5, PA6, PA7, PA8, PA9, PA10, PA11, PA12, PA13, PA14, PA15,
+    PB0 = 1 << 4, PB1, PB2, PB3, PB4, PB5, PB6, PB7, PB8, PB9, PB10, PB11, PB12, PB13, PB14, PB15,
+    PC0 = 2 << 4, PC1, PC2, PC3, PC4, PC5, PC6, PC7, PC8, PC9, PC10, PC11, PC12, PC13, PC14, PC15,
+    PD0 = 3 << 4, PD1, PD2, PD3, PD4, PD5, PD6, PD7, PD8, PD9, PD10, PD11, PD12, PD13, PD14, PD15,
+    PE0 = 4 << 4, PE1, PE2, PE3, PE4, PE5, PE6, PE7, PE8, PE9, PE10, PE11, PE12, PE13, PE14, PE15,
+    PF0 = 5 << 4, PF1, PF2, PF3, PF4, PF5, PF6, PF7, PF8, PF9, PF10, PF11, PF12, PF13, PF14, PF15,
+
+    /* Starter Kit says LED0 and LED1, but mbed expects 1 and 2. This way using 1 and 2 or 0 and 1 will work. */
+    LED0 = PE2,
+    LED1 = PE3,
+    LED2 = LED0,
+    LED3 = LED0,
+    LED4 = LED1,
+
+    /* Push Buttons */
+    SW0 = PB9,
+    SW1 = PB10,
+    BTN0 = SW0,
+    BTN1 = SW1,
+
+    /* Serial */
+    SERIAL_TX   = PD0,
+    SERIAL_RX   = PD1,
+    USBTX       = PE0,
+    USBRX       = PE1,
+    EFM_BC_EN   = PF7,
+
+    /* Not connected */
+    NC = (int) 0xFFFFFFFF
+} PinName;
+
+
+/* 0x10 represents setting the DOUT register (see efm32 modes in ref. manual) */
+typedef enum {
+    /* EFM32 pin modes */
+    Disabled        = gpioModeDisabled,
+    DisabledPullUp  = gpioModeDisabled | 0x10,
+    Input 			= gpioModeInput,
+    InputFilter 	= gpioModeInput | 0x10,
+    InputPullDown 	= gpioModeInputPull,
+    InputPullUp     = gpioModeInputPull | 0x10,
+    InputPullFilterDown = gpioModeInputPullFilter,
+    InputPullFilterUp 	= gpioModeInputPullFilter | 0x10,
+    PushPull 		= gpioModePushPull,
+    PushPullDrive 	= gpioModePushPullDrive,
+    WiredOr 		= gpioModeWiredOr,
+    WiredOrPullDown = gpioModeWiredOrPullDown,
+    WiredAnd 		= gpioModeWiredAnd,
+    WiredAndFilter 	= gpioModeWiredAndFilter,
+    WiredAndPullUp 	= gpioModeWiredAndPullUp,
+    WiredAndPullUpFilter = gpioModeWiredAndPullUpFilter,
+    WiredAndDrive 		= gpioModeWiredAndDrive,
+    WiredAndDriveFilter	= gpioModeWiredAndDriveFilter,
+    WiredAndDrivePullUp	= gpioModeWiredAndDrivePullUp,
+    WiredAndDrivePullUpFilter = gpioModeWiredAndDrivePullUpFilter,
+
+    /* mbed modes:
+     * PullUp, PullDown, PullNone, OpenDrain
+     *
+     * mbed default digital input mode:
+     * PullDefault
+     *
+     * mbed default digital output mode:
+     * PullNone
+     */
+    PullUp = InputPullUp,
+    PullDown = InputPullDown,
+    OpenDrain = WiredAnd,
+    PullNone = PushPull,
+    PullDefault = PushPull
+} PinMode;
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif