added prescaler for 16 bit pwm in LPC1347 target
Fork of mbed-dev by
Diff: targets/cmsis/TARGET_STM/TARGET_STM32F7/stm32f7xx_hal_uart.c
- Revision:
- 0:9b334a45a8ff
- Child:
- 83:a036322b8637
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_STM32F7/stm32f7xx_hal_uart.c Thu Oct 01 15:25:22 2015 +0300 @@ -0,0 +1,1996 @@ +/** + ****************************************************************************** + * @file stm32f7xx_hal_uart.c + * @author MCD Application Team + * @version V1.0.1 + * @date 25-June-2015 + * @brief UART HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Universal Asynchronous Receiver Transmitter (UART) peripheral: + * + Initialization and de-initialization functions + * + IO operation functions + * + Peripheral Control functions + * + Peripheral State and Errors functions + * + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] + The UART HAL driver can be used as follows: + + (#) Declare a UART_HandleTypeDef handle structure. + + (#) Initialize the UART low level resources by implementing the HAL_UART_MspInit() API: + (##) Enable the USARTx interface clock. + (##) UART pins configuration: + (+++) Enable the clock for the UART GPIOs. + (+++) Configure these UART pins as alternate function pull-up. + (##) NVIC configuration if you need to use interrupt process (HAL_UART_Transmit_IT() + and HAL_UART_Receive_IT() APIs): + (+++) Configure the USARTx interrupt priority. + (+++) Enable the NVIC USART IRQ handle. + (##) DMA Configuration if you need to use DMA process (HAL_UART_Transmit_DMA() + and HAL_UART_Receive_DMA() APIs): + (+++) Declare a DMA handle structure for the Tx/Rx stream. + (+++) Enable the DMAx interface clock. + (+++) Configure the declared DMA handle structure with the required + Tx/Rx parameters. + (+++) Configure the DMA Tx/Rx Stream. + (+++) Associate the initialized DMA handle to the UART DMA Tx/Rx handle. + (+++) Configure the priority and enable the NVIC for the transfer complete + interrupt on the DMA Tx/Rx Stream. + + (#) Program the Baud Rate, Word Length, Stop Bit, Parity, Hardware + flow control and Mode(Receiver/Transmitter) in the Init structure. + + (#) For the UART asynchronous mode, initialize the UART registers by calling + the HAL_UART_Init() API. + + (#) For the UART Half duplex mode, initialize the UART registers by calling + the HAL_HalfDuplex_Init() API. + + (#) For the LIN mode, initialize the UART registers by calling the HAL_LIN_Init() API. + + (#) For the Multi-Processor mode, initialize the UART registers by calling + the HAL_MultiProcessor_Init() API. + + [..] + (@) The specific UART interrupts (Transmission complete interrupt, + RXNE interrupt and Error Interrupts) will be managed using the macros + __HAL_UART_ENABLE_IT() and __HAL_UART_DISABLE_IT() inside the transmit + and receive process. + + [..] + (@) These APIs (HAL_UART_Init() and HAL_HalfDuplex_Init()) configure also the + low level Hardware GPIO, CLOCK, CORTEX...etc) by calling the customized + HAL_UART_MspInit() API. + + [..] + Three operation modes are available within this driver : + + *** Polling mode IO operation *** + ================================= + [..] + (+) Send an amount of data in blocking mode using HAL_UART_Transmit() + (+) Receive an amount of data in blocking mode using HAL_UART_Receive() + + *** Interrupt mode IO operation *** + =================================== + [..] + (+) Send an amount of data in non blocking mode using HAL_UART_Transmit_IT() + (+) At transmission end of transfer HAL_UART_TxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_TxCpltCallback + (+) Receive an amount of data in non blocking mode using HAL_UART_Receive_IT() + (+) At reception end of transfer HAL_UART_RxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_RxCpltCallback + (+) In case of transfer Error, HAL_UART_ErrorCallback() function is executed and user can + add his own code by customization of function pointer HAL_UART_ErrorCallback + + *** DMA mode IO operation *** + ============================== + [..] + (+) Send an amount of data in non blocking mode (DMA) using HAL_UART_Transmit_DMA() + (+) At transmission end of half transfer HAL_UART_TxHalfCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_TxHalfCpltCallback + (+) At transmission end of transfer HAL_UART_TxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_TxCpltCallback + (+) Receive an amount of data in non blocking mode (DMA) using HAL_UART_Receive_DMA() + (+) At reception end of half transfer HAL_UART_RxHalfCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_RxHalfCpltCallback + (+) At reception end of transfer HAL_UART_RxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_RxCpltCallback + (+) In case of transfer Error, HAL_UART_ErrorCallback() function is executed and user can + add his own code by customization of function pointer HAL_UART_ErrorCallback + (+) Pause the DMA Transfer using HAL_UART_DMAPause() + (+) Resume the DMA Transfer using HAL_UART_DMAResume() + (+) Stop the DMA Transfer using HAL_UART_DMAStop() + + *** UART HAL driver macros list *** + ============================================= + [..] + Below the list of most used macros in UART HAL driver. + + (+) __HAL_UART_ENABLE: Enable the UART peripheral + (+) __HAL_UART_DISABLE: Disable the UART peripheral + (+) __HAL_UART_GET_FLAG : Check whether the specified UART flag is set or not + (+) __HAL_UART_CLEAR_IT : Clears the specified UART ISR flag + (+) __HAL_UART_ENABLE_IT: Enable the specified UART interrupt + (+) __HAL_UART_DISABLE_IT: Disable the specified UART interrupt + (+) __HAL_UART_GET_IT_SOURCE: Check whether the specified UART interrupt has occurred or not + + [..] + (@) You can refer to the UART HAL driver header file for more useful macros + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f7xx_hal.h" + +/** @addtogroup STM32F7xx_HAL_Driver + * @{ + */ + +/** @defgroup UART UART + * @brief HAL UART module driver + * @{ + */ +#ifdef HAL_UART_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +#define HAL_UART_TXDMA_TIMEOUTVALUE 22000 +#define UART_CR1_FIELDS ((uint32_t)(USART_CR1_M | USART_CR1_PCE | USART_CR1_PS | \ + USART_CR1_TE | USART_CR1_RE | USART_CR1_OVER8)) +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +static void UART_DMATransmitCplt(DMA_HandleTypeDef *hdma); +static void UART_DMAReceiveCplt(DMA_HandleTypeDef *hdma); +static void UART_DMARxHalfCplt(DMA_HandleTypeDef *hdma); +static void UART_DMATxHalfCplt(DMA_HandleTypeDef *hdma); +static void UART_DMAError(DMA_HandleTypeDef *hdma); +static HAL_StatusTypeDef UART_Transmit_IT(UART_HandleTypeDef *huart); +static HAL_StatusTypeDef UART_EndTransmit_IT(UART_HandleTypeDef *huart); +static HAL_StatusTypeDef UART_Receive_IT(UART_HandleTypeDef *huart); +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup UART_Exported_Functions UART Exported Functions + * @{ + */ + +/** @defgroup UART_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim +=============================================================================== + ##### Initialization and Configuration functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to initialize the USARTx or the UARTy + in asynchronous mode. + (+) For the asynchronous mode only these parameters can be configured: + (++) Baud Rate + (++) Word Length + (++) Stop Bit + (++) Parity: If the parity is enabled, then the MSB bit of the data written + in the data register is transmitted but is changed by the parity bit. + Depending on the frame length defined by the M bit (8-bits or 9-bits), + please refer to Reference manual for possible UART frame formats. + (++) Hardware flow control + (++) Receiver/transmitter modes + (++) Over Sampling Method + [..] + The HAL_UART_Init(), HAL_HalfDuplex_Init(), HAL_LIN_Init() and HAL_MultiProcessor_Init() APIs + follow respectively the UART asynchronous, UART Half duplex, LIN and Multi-Processor + configuration procedures (details for the procedures are available in reference manual (RM0329)). + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the UART mode according to the specified + * parameters in the UART_InitTypeDef and creates the associated handle . + * @param huart: uart handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + if(huart->Init.HwFlowCtl != UART_HWCONTROL_NONE) + { + /* Check the parameters */ + assert_param(IS_UART_HWFLOW_INSTANCE(huart->Instance)); + } + else + { + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + } + + if(huart->State == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + + /* Init the low level hardware : GPIO, CLOCK */ + HAL_UART_MspInit(huart); + } + + huart->State = HAL_UART_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + if (UART_SetConfig(huart) == HAL_ERROR) + { + return HAL_ERROR; + } + + if (huart->AdvancedInit.AdvFeatureInit != UART_ADVFEATURE_NO_INIT) + { + UART_AdvFeatureConfig(huart); + } + + /* In asynchronous mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN, HDSEL and IREN bits in the USART_CR3 register.*/ + huart->Instance->CR2 &= ~(USART_CR2_LINEN | USART_CR2_CLKEN); + huart->Instance->CR3 &= ~(USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN); + + /* Enable the Peripheral */ + __HAL_UART_ENABLE(huart); + + /* TEACK and/or REACK to check before moving huart->State to Ready */ + return (UART_CheckIdleState(huart)); +} + +/** + * @brief Initializes the half-duplex mode according to the specified + * parameters in the UART_InitTypeDef and creates the associated handle . + * @param huart: UART handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + if(huart->State == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + /* Init the low level hardware : GPIO, CLOCK */ + HAL_UART_MspInit(huart); + } + + huart->State = HAL_UART_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + if (UART_SetConfig(huart) == HAL_ERROR) + { + return HAL_ERROR; + } + + if (huart->AdvancedInit.AdvFeatureInit != UART_ADVFEATURE_NO_INIT) + { + UART_AdvFeatureConfig(huart); + } + + /* In half-duplex mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN and IREN bits in the USART_CR3 register.*/ + huart->Instance->CR2 &= ~(USART_CR2_LINEN | USART_CR2_CLKEN); + huart->Instance->CR3 &= ~(USART_CR3_IREN | USART_CR3_SCEN); + + /* Enable the Half-Duplex mode by setting the HDSEL bit in the CR3 register */ + huart->Instance->CR3 |= USART_CR3_HDSEL; + + /* Enable the Peripheral */ + __HAL_UART_ENABLE(huart); + + /* TEACK and/or REACK to check before moving huart->State to Ready */ + return (UART_CheckIdleState(huart)); +} + + +/** + * @brief Initializes the LIN mode according to the specified + * parameters in the UART_InitTypeDef and creates the associated handle . + * @param huart: uart handle + * @param BreakDetectLength: specifies the LIN break detection length. + * This parameter can be one of the following values: + * @arg UART_LINBREAKDETECTLENGTH_10B: 10-bit break detection + * @arg UART_LINBREAKDETECTLENGTH_11B: 11-bit break detection + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + assert_param(IS_UART_LIN_BREAK_DETECT_LENGTH(BreakDetectLength)); + assert_param(IS_LIN_WORD_LENGTH(huart->Init.WordLength)); + + if(huart->State == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + /* Init the low level hardware : GPIO, CLOCK */ + HAL_UART_MspInit(huart); + } + + huart->State = HAL_UART_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + if (UART_SetConfig(huart) == HAL_ERROR) + { + return HAL_ERROR; + } + + if (huart->AdvancedInit.AdvFeatureInit != UART_ADVFEATURE_NO_INIT) + { + UART_AdvFeatureConfig(huart); + } + + /* In LIN mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN and IREN bits in the USART_CR3 register.*/ + huart->Instance->CR2 &= ~(USART_CR2_CLKEN); + huart->Instance->CR3 &= ~(USART_CR3_HDSEL | USART_CR3_IREN | USART_CR3_SCEN); + + /* Enable the LIN mode by setting the LINEN bit in the CR2 register */ + huart->Instance->CR2 |= USART_CR2_LINEN; + + /* Set the USART LIN Break detection length. */ + MODIFY_REG(huart->Instance->CR2, USART_CR2_LBDL, BreakDetectLength); + + /* Enable the Peripheral */ + __HAL_UART_ENABLE(huart); + + /* TEACK and/or REACK to check before moving huart->State to Ready */ + return (UART_CheckIdleState(huart)); +} + + + +/** + * @brief Initializes the multiprocessor mode according to the specified + * parameters in the UART_InitTypeDef and creates the associated handle. + * @param huart: UART handle + * @param Address: UART node address (4-, 6-, 7- or 8-bit long) + * @param WakeUpMethod: specifies the UART wakeup method. + * This parameter can be one of the following values: + * @arg UART_WAKEUPMETHOD_IDLELINE: WakeUp by an idle line detection + * @arg UART_WAKEUPMETHOD_ADDRESSMARK: WakeUp by an address mark + * @note If the user resorts to idle line detection wake up, the Address parameter + * is useless and ignored by the initialization function. + * @note If the user resorts to address mark wake up, the address length detection + * is configured by default to 4 bits only. For the UART to be able to + * manage 6-, 7- or 8-bit long addresses detection + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethod) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check the wake up method parameter */ + assert_param(IS_UART_WAKEUPMETHOD(WakeUpMethod)); + + if(huart->State == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + /* Init the low level hardware : GPIO, CLOCK */ + HAL_UART_MspInit(huart); + } + + huart->State = HAL_UART_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + if (UART_SetConfig(huart) == HAL_ERROR) + { + return HAL_ERROR; + } + + if (huart->AdvancedInit.AdvFeatureInit != UART_ADVFEATURE_NO_INIT) + { + UART_AdvFeatureConfig(huart); + } + + /* In multiprocessor mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN, HDSEL and IREN bits in the USART_CR3 register. */ + huart->Instance->CR2 &= ~(USART_CR2_LINEN | USART_CR2_CLKEN); + huart->Instance->CR3 &= ~(USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN); + + if (WakeUpMethod == UART_WAKEUPMETHOD_ADDRESSMARK) + { + /* If address mark wake up method is chosen, set the USART address node */ + MODIFY_REG(huart->Instance->CR2, USART_CR2_ADD, ((uint32_t)Address << UART_CR2_ADDRESS_LSB_POS)); + } + + /* Set the wake up method by setting the WAKE bit in the CR1 register */ + MODIFY_REG(huart->Instance->CR1, USART_CR1_WAKE, WakeUpMethod); + + /* Enable the Peripheral */ + __HAL_UART_ENABLE(huart); + + /* TEACK and/or REACK to check before moving huart->State to Ready */ + return (UART_CheckIdleState(huart)); +} + + + + +/** + * @brief DeInitializes the UART peripheral + * @param huart: uart handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DeInit(UART_HandleTypeDef *huart) +{ + /* Check the UART handle allocation */ + if(huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + huart->State = HAL_UART_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_UART_DISABLE(huart); + + huart->Instance->CR1 = 0x0; + huart->Instance->CR2 = 0x0; + huart->Instance->CR3 = 0x0; + + /* DeInit the low level hardware */ + HAL_UART_MspDeInit(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->State = HAL_UART_STATE_RESET; + + /* Process Unlock */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief UART MSP Init + * @param huart: uart handle + * @retval None + */ + __weak void HAL_UART_MspInit(UART_HandleTypeDef *huart) +{ + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_UART_MspInit can be implemented in the user file + */ +} + +/** + * @brief UART MSP DeInit + * @param huart: uart handle + * @retval None + */ + __weak void HAL_UART_MspDeInit(UART_HandleTypeDef *huart) +{ + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_UART_MspDeInit can be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup UART_Exported_Functions_Group2 IO operation functions + * @brief UART Transmit/Receive functions + * +@verbatim + =============================================================================== + ##### IO operation functions ##### + =============================================================================== + This subsection provides a set of functions allowing to manage the UART asynchronous + and Half duplex data transfers. + + (#) There are two mode of transfer: + (+) Blocking mode: The communication is performed in polling mode. + The HAL status of all data processing is returned by the same function + after finishing transfer. + (+) No-Blocking mode: The communication is performed using Interrupts + or DMA, These API's return the HAL status. + The end of the data processing will be indicated through the + dedicated UART IRQ when using Interrupt mode or the DMA IRQ when + using DMA mode. + The HAL_UART_TxCpltCallback(), HAL_UART_RxCpltCallback() user callbacks + will be executed respectively at the end of the transmit or Receive process + The HAL_UART_ErrorCallback()user callback will be executed when a communication error is detected + + (#) Blocking mode API's are : + (+) HAL_UART_Transmit() + (+) HAL_UART_Receive() + + (#) Non-Blocking mode API's with Interrupt are : + (+) HAL_UART_Transmit_IT() + (+) HAL_UART_Receive_IT() + (+) HAL_UART_IRQHandler() + (+) UART_Transmit_IT() + (+) UART_Receive_IT() + + (#) No-Blocking mode API's with DMA are : + (+) HAL_UART_Transmit_DMA() + (+) HAL_UART_Receive_DMA() + (+) HAL_UART_DMAPause() + (+) HAL_UART_DMAResume() + (+) HAL_UART_DMAStop() + + (#) A set of Transfer Complete Callbacks are provided in No_Blocking mode: + (+) HAL_UART_TxHalfCpltCallback() + (+) HAL_UART_TxCpltCallback() + (+) HAL_UART_RxHalfCpltCallback() + (+) HAL_UART_RxCpltCallback() + (+) HAL_UART_ErrorCallback() + + + -@- In the Half duplex communication, it is forbidden to run the transmit + and receive process in parallel, the UART state HAL_UART_STATE_BUSY_TX_RX can't be useful. + +@endverbatim + * @{ + */ + +/** + * @brief Send an amount of data in blocking mode + * @param huart: uart handle + * @param pData: pointer to data buffer + * @param Size: amount of data to be sent + * @param Timeout : Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout) +{ + uint16_t* tmp; + + if((huart->State == HAL_UART_STATE_READY) || (huart->State == HAL_UART_STATE_BUSY_RX)) + { + if((pData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + /* Check if a non-blocking receive process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_RX) + { + huart->State = HAL_UART_STATE_BUSY_TX_RX; + } + else + { + huart->State = HAL_UART_STATE_BUSY_TX; + } + + huart->TxXferSize = Size; + huart->TxXferCount = Size; + while(huart->TxXferCount > 0) + { + huart->TxXferCount--; + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_TXE, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE)) + { + tmp = (uint16_t*) pData; + huart->Instance->TDR = (*tmp & (uint16_t)0x01FF); + pData += 2; + } + else + { + huart->Instance->TDR = (*pData++ & (uint8_t)0xFF); + } + } + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_TC, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + /* Check if a non-blocking receive Process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + huart->State = HAL_UART_STATE_BUSY_RX; + } + else + { + huart->State = HAL_UART_STATE_READY; + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive an amount of data in blocking mode + * @param huart: uart handle + * @param pData: pointer to data buffer + * @param Size: amount of data to be received + * @param Timeout : Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout) +{ + uint16_t* tmp; + uint16_t uhMask; + + if((huart->State == HAL_UART_STATE_READY) || (huart->State == HAL_UART_STATE_BUSY_TX)) + { + if((pData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + /* Check if a non-blocking transmit process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX) + { + huart->State = HAL_UART_STATE_BUSY_TX_RX; + } + else + { + huart->State = HAL_UART_STATE_BUSY_RX; + } + + huart->RxXferSize = Size; + huart->RxXferCount = Size; + + /* Computation of UART mask to apply to RDR register */ + UART_MASK_COMPUTATION(huart); + uhMask = huart->Mask; + + /* as long as data have to be received */ + while(huart->RxXferCount > 0) + { + huart->RxXferCount--; + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_RXNE, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE)) + { + tmp = (uint16_t*) pData ; + *tmp = (uint16_t)(huart->Instance->RDR & uhMask); + pData +=2; + } + else + { + *pData++ = (uint8_t)(huart->Instance->RDR & (uint8_t)uhMask); + } + } + + /* Check if a non-blocking transmit Process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + huart->State = HAL_UART_STATE_BUSY_TX; + } + else + { + huart->State = HAL_UART_STATE_READY; + } + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Send an amount of data in interrupt mode + * @param huart: uart handle + * @param pData: pointer to data buffer + * @param Size: amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + if((huart->State == HAL_UART_STATE_READY) || (huart->State == HAL_UART_STATE_BUSY_RX)) + { + if((pData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pTxBuffPtr = pData; + huart->TxXferSize = Size; + huart->TxXferCount = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + /* Check if a receive process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_RX) + { + huart->State = HAL_UART_STATE_BUSY_TX_RX; + } + else + { + huart->State = HAL_UART_STATE_BUSY_TX; + } + + /* Enable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_UART_ENABLE_IT(huart, UART_IT_ERR); + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + /* Enable the UART Transmit Data Register Empty Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_TXE); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive an amount of data in interrupt mode + * @param huart: uart handle + * @param pData: pointer to data buffer + * @param Size: amount of data to be received + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + if((huart->State == HAL_UART_STATE_READY) || (huart->State == HAL_UART_STATE_BUSY_TX)) + { + if((pData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pRxBuffPtr = pData; + huart->RxXferSize = Size; + huart->RxXferCount = Size; + + /* Computation of UART mask to apply to RDR register */ + UART_MASK_COMPUTATION(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + /* Check if a transmit process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX) + { + huart->State = HAL_UART_STATE_BUSY_TX_RX; + } + else + { + huart->State = HAL_UART_STATE_BUSY_RX; + } + + /* Enable the UART Parity Error Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_PE); + + /* Enable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_UART_ENABLE_IT(huart, UART_IT_ERR); + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + /* Enable the UART Data Register not empty Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_RXNE); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Send an amount of data in DMA mode + * @param huart: uart handle + * @param pData: pointer to data buffer + * @param Size: amount of data to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + uint32_t *tmp; + + if((huart->State == HAL_UART_STATE_READY) || (huart->State == HAL_UART_STATE_BUSY_RX)) + { + if((pData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pTxBuffPtr = pData; + huart->TxXferSize = Size; + huart->TxXferCount = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + /* Check if a receive process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_RX) + { + huart->State = HAL_UART_STATE_BUSY_TX_RX; + } + else + { + huart->State = HAL_UART_STATE_BUSY_TX; + } + + /* Set the UART DMA transfer complete callback */ + huart->hdmatx->XferCpltCallback = UART_DMATransmitCplt; + + /* Set the UART DMA Half transfer complete callback */ + huart->hdmatx->XferHalfCpltCallback = UART_DMATxHalfCplt; + + /* Set the DMA error callback */ + huart->hdmatx->XferErrorCallback = UART_DMAError; + + /* Enable the UART transmit DMA channel */ + tmp = (uint32_t*)&pData; + HAL_DMA_Start_IT(huart->hdmatx, *(uint32_t*)tmp, (uint32_t)&huart->Instance->TDR, Size); + + /* Clear the TC flag in the SR register by writing 0 to it */ + __HAL_UART_CLEAR_IT(huart, UART_FLAG_TC); + + + /* Enable the DMA transfer for transmit request by setting the DMAT bit + in the UART CR3 register */ + huart->Instance->CR3 |= USART_CR3_DMAT; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive an amount of data in DMA mode + * @param huart: uart handle + * @param pData: pointer to data buffer + * @param Size: amount of data to be received + * @note When the UART parity is enabled (PCE = 1), the received data contain + * the parity bit (MSB position) + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + uint32_t *tmp; + + if((huart->State == HAL_UART_STATE_READY) || (huart->State == HAL_UART_STATE_BUSY_TX)) + { + if((pData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pRxBuffPtr = pData; + huart->RxXferSize = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + /* Check if a transmit process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX) + { + huart->State = HAL_UART_STATE_BUSY_TX_RX; + } + else + { + huart->State = HAL_UART_STATE_BUSY_RX; + } + + /* Set the UART DMA transfer complete callback */ + huart->hdmarx->XferCpltCallback = UART_DMAReceiveCplt; + + /* Set the UART DMA Half transfer complete callback */ + huart->hdmarx->XferHalfCpltCallback = UART_DMARxHalfCplt; + + /* Set the DMA error callback */ + huart->hdmarx->XferErrorCallback = UART_DMAError; + + /* Enable the DMA channel */ + tmp = (uint32_t*)&pData; + HAL_DMA_Start_IT(huart->hdmarx, (uint32_t)&huart->Instance->RDR, *(uint32_t*)tmp, Size); + + /* Enable the DMA transfer for the receiver request by setting the DMAR bit + in the UART CR3 register */ + huart->Instance->CR3 |= USART_CR3_DMAR; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Pauses the DMA Transfer. + * @param huart: UART handle + * @retval None + */ +HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart) +{ + /* Process Locked */ + __HAL_LOCK(huart); + + if(huart->State == HAL_UART_STATE_BUSY_TX) + { + /* Disable the UART DMA Tx request */ + huart->Instance->CR3 &= (uint32_t)(~USART_CR3_DMAT); + } + else if(huart->State == HAL_UART_STATE_BUSY_RX) + { + /* Disable the UART DMA Rx request */ + huart->Instance->CR3 &= (uint32_t)(~USART_CR3_DMAR); + } + else if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + /* Disable the UART DMA Tx request */ + huart->Instance->CR3 &= (uint32_t)(~USART_CR3_DMAT); + /* Disable the UART DMA Rx request */ + huart->Instance->CR3 &= (uint32_t)(~USART_CR3_DMAR); + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Resumes the DMA Transfer. + * @param huart: UART handle + * @retval None + */ +HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart) +{ + /* Process Locked */ + __HAL_LOCK(huart); + + if(huart->State == HAL_UART_STATE_BUSY_TX) + { + /* Enable the UART DMA Tx request */ + huart->Instance->CR3 |= USART_CR3_DMAT; + } + else if(huart->State == HAL_UART_STATE_BUSY_RX) + { + /* Clear the Overrun flag before resuming the Rx transfer*/ + __HAL_UART_CLEAR_IT(huart, UART_CLEAR_OREF); + + /* Enable the UART DMA Rx request */ + huart->Instance->CR3 |= USART_CR3_DMAR; + } + else if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + /* Clear the Overrun flag before resuming the Rx transfer*/ + __HAL_UART_CLEAR_IT(huart, UART_CLEAR_OREF); + + /* Enable the UART DMA Rx request before the DMA Tx request */ + huart->Instance->CR3 |= USART_CR3_DMAR; + + /* Enable the UART DMA Tx request */ + huart->Instance->CR3 |= USART_CR3_DMAT; + } + + /* If the UART peripheral is still not enabled, enable it */ + if ((huart->Instance->CR1 & USART_CR1_UE) == 0) + { + /* Enable UART peripheral */ + __HAL_UART_ENABLE(huart); + } + + return HAL_OK; +} + +/** + * @brief Stops the DMA Transfer. + * @param huart: UART handle + * @retval None + */ +HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart) +{ + /* The Lock is not implemented on this API to allow the user application + to call the HAL UART API under callbacks HAL_UART_TxCpltCallback() / HAL_UART_RxCpltCallback() / + HAL_UART_TxHalfCpltCallback / HAL_UART_RxHalfCpltCallback: + indeed, when HAL_DMA_Abort() API is called, the DMA TX/RX Transfer or Half Transfer complete + interrupt is generated if the DMA transfer interruption occurs at the middle or at the end of + the stream and the corresponding call back is executed. */ + + /* Disable the UART Tx/Rx DMA requests */ + huart->Instance->CR3 &= ~USART_CR3_DMAT; + huart->Instance->CR3 &= ~USART_CR3_DMAR; + + /* Abort the UART DMA tx channel */ + if(huart->hdmatx != NULL) + { + HAL_DMA_Abort(huart->hdmatx); + } + /* Abort the UART DMA rx channel */ + if(huart->hdmarx != NULL) + { + HAL_DMA_Abort(huart->hdmarx); + } + + huart->State = HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief This function handles UART interrupt request. + * @param huart: uart handle + * @retval None + */ +void HAL_UART_IRQHandler(UART_HandleTypeDef *huart) +{ + /* UART parity error interrupt occurred -------------------------------------*/ + if((__HAL_UART_GET_IT(huart, UART_IT_PE) != RESET) && (__HAL_UART_GET_IT_SOURCE(huart, UART_IT_PE) != RESET)) + { + __HAL_UART_CLEAR_PEFLAG(huart); + + huart->ErrorCode |= HAL_UART_ERROR_PE; + /* Set the UART state ready to be able to start again the process */ + huart->State = HAL_UART_STATE_READY; + } + + /* UART frame error interrupt occurred --------------------------------------*/ + if((__HAL_UART_GET_IT(huart, UART_IT_FE) != RESET) && (__HAL_UART_GET_IT_SOURCE(huart, UART_IT_ERR) != RESET)) + { + __HAL_UART_CLEAR_FEFLAG(huart); + + huart->ErrorCode |= HAL_UART_ERROR_FE; + /* Set the UART state ready to be able to start again the process */ + huart->State = HAL_UART_STATE_READY; + } + + /* UART noise error interrupt occurred --------------------------------------*/ + if((__HAL_UART_GET_IT(huart, UART_IT_NE) != RESET) && (__HAL_UART_GET_IT_SOURCE(huart, UART_IT_ERR) != RESET)) + { + __HAL_UART_CLEAR_NEFLAG(huart); + + huart->ErrorCode |= HAL_UART_ERROR_NE; + /* Set the UART state ready to be able to start again the process */ + huart->State = HAL_UART_STATE_READY; + } + + /* UART Over-Run interrupt occurred -----------------------------------------*/ + if((__HAL_UART_GET_IT(huart, UART_IT_ORE) != RESET) && (__HAL_UART_GET_IT_SOURCE(huart, UART_IT_ERR) != RESET)) + { + __HAL_UART_CLEAR_OREFLAG(huart); + + huart->ErrorCode |= HAL_UART_ERROR_ORE; + /* Set the UART state ready to be able to start again the process */ + huart->State = HAL_UART_STATE_READY; + } + + /* Call UART Error Call back function if need be --------------------------*/ + if(huart->ErrorCode != HAL_UART_ERROR_NONE) + { + HAL_UART_ErrorCallback(huart); + } + + /* UART in mode Receiver ---------------------------------------------------*/ + if((__HAL_UART_GET_IT(huart, UART_IT_RXNE) != RESET) && (__HAL_UART_GET_IT_SOURCE(huart, UART_IT_RXNE) != RESET)) + { + UART_Receive_IT(huart); + /* Clear RXNE interrupt flag */ + __HAL_UART_SEND_REQ(huart, UART_RXDATA_FLUSH_REQUEST); + } + + + /* UART in mode Transmitter ------------------------------------------------*/ + if((__HAL_UART_GET_IT(huart, UART_IT_TXE) != RESET) &&(__HAL_UART_GET_IT_SOURCE(huart, UART_IT_TXE) != RESET)) + { + UART_Transmit_IT(huart); + } + + /* UART in mode Transmitter (transmission end) -----------------------------*/ + if((__HAL_UART_GET_IT(huart, UART_IT_TC) != RESET) &&(__HAL_UART_GET_IT_SOURCE(huart, UART_IT_TC) != RESET)) + { + UART_EndTransmit_IT(huart); + } + +} + + +/** + * @brief This function handles UART Communication Timeout. + * @param huart: UART handle + * @param Flag: specifies the UART flag to check. + * @param Status: The new Flag status (SET or RESET). + * @param Timeout: Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef UART_WaitOnFlagUntilTimeout(UART_HandleTypeDef *huart, uint32_t Flag, FlagStatus Status, uint32_t Timeout) +{ + uint32_t tickstart = HAL_GetTick(); + + /* Wait until flag is set */ + if(Status == RESET) + { + while(__HAL_UART_GET_FLAG(huart, Flag) == RESET) + { + /* Check for the Timeout */ + if(Timeout != HAL_MAX_DELAY) + { + if((Timeout == 0)||((HAL_GetTick()-tickstart) >= Timeout)) + { + /* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts for the interrupt process */ + __HAL_UART_DISABLE_IT(huart, UART_IT_TXE); + __HAL_UART_DISABLE_IT(huart, UART_IT_RXNE); + __HAL_UART_DISABLE_IT(huart, UART_IT_PE); + __HAL_UART_DISABLE_IT(huart, UART_IT_ERR); + + huart->State= HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_TIMEOUT; + } + } + } + } + else + { + while(__HAL_UART_GET_FLAG(huart, Flag) != RESET) + { + /* Check for the Timeout */ + if(Timeout != HAL_MAX_DELAY) + { + if((Timeout == 0)||((HAL_GetTick()-tickstart) >= Timeout)) + { + /* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts for the interrupt process */ + __HAL_UART_DISABLE_IT(huart, UART_IT_TXE); + __HAL_UART_DISABLE_IT(huart, UART_IT_RXNE); + __HAL_UART_DISABLE_IT(huart, UART_IT_PE); + __HAL_UART_DISABLE_IT(huart, UART_IT_ERR); + + huart->State= HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_TIMEOUT; + } + } + } + } + return HAL_OK; +} + + + +/** + * @brief DMA UART transmit process complete callback + * @param hdma: DMA handle + * @retval None + */ +static void UART_DMATransmitCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = ( UART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + + /* DMA Normal mode*/ + if((hdma->Instance->CR & DMA_SxCR_CIRC) == 0) + { + huart->TxXferCount = 0; + + /* Disable the DMA transfer for transmit request by setting the DMAT bit + in the UART CR3 register */ + huart->Instance->CR3 &= (uint32_t)~((uint32_t)USART_CR3_DMAT); + + /* Enable the UART Transmit Complete Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_TC); + } + /* DMA Circular mode */ + else + { + HAL_UART_TxCpltCallback(huart); + } +} + +/** + * @brief DMA UART transmit process half complete callback + * @param hdma : DMA handle + * @retval None + */ +static void UART_DMATxHalfCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = (UART_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + HAL_UART_TxHalfCpltCallback(huart); +} + +/** + * @brief DMA UART receive process complete callback + * @param hdma: DMA handle + * @retval None + */ +static void UART_DMAReceiveCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = ( UART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + + /* DMA Normal mode */ + if((hdma->Instance->CR & DMA_SxCR_CIRC) == 0) + { + huart->RxXferCount = 0; + + /* Disable the DMA transfer for the receiver request by setting the DMAR bit + in the UART CR3 register */ + huart->Instance->CR3 &= (uint32_t)~((uint32_t)USART_CR3_DMAR); + + /* Check if a transmit Process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + huart->State = HAL_UART_STATE_BUSY_TX; + } + else + { + huart->State = HAL_UART_STATE_READY; + } + } + HAL_UART_RxCpltCallback(huart); +} + +/** + * @brief DMA UART receive process half complete callback + * @param hdma : DMA handle + * @retval None + */ +static void UART_DMARxHalfCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = (UART_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + HAL_UART_RxHalfCpltCallback(huart); +} + +/** + * @brief DMA UART communication error callback + * @param hdma: DMA handle + * @retval None + */ +static void UART_DMAError(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef* huart = ( UART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + huart->RxXferCount = 0; + huart->TxXferCount = 0; + huart->State= HAL_UART_STATE_READY; + huart->ErrorCode |= HAL_UART_ERROR_DMA; + HAL_UART_ErrorCallback(huart); +} + +/** + * @brief Tx Transfer completed callbacks + * @param huart: uart handle + * @retval None + */ + __weak void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart) +{ + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_UART_TxCpltCallback can be implemented in the user file + */ +} + +/** + * @brief Tx Half Transfer completed callbacks. + * @param huart: UART handle + * @retval None + */ + __weak void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart) +{ + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_TxHalfCpltCallback can be implemented in the user file + */ +} + +/** + * @brief Rx Transfer completed callbacks + * @param huart: uart handle + * @retval None + */ +__weak void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart) +{ + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_UART_RxCpltCallback can be implemented in the user file + */ +} + +/** + * @brief Rx Half Transfer completed callbacks. + * @param huart: UART handle + * @retval None + */ +__weak void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart) +{ + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_RxHalfCpltCallback can be implemented in the user file + */ +} + +/** + * @brief UART error callbacks + * @param huart: uart handle + * @retval None + */ + __weak void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart) +{ + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_UART_ErrorCallback can be implemented in the user file + */ +} + +/** + * @brief Send an amount of data in interrupt mode + * Function called under interruption only, once + * interruptions have been enabled by HAL_UART_Transmit_IT() + * @param huart: UART handle + * @retval HAL status + */ +static HAL_StatusTypeDef UART_Transmit_IT(UART_HandleTypeDef *huart) +{ + uint16_t* tmp; + + if ((huart->State == HAL_UART_STATE_BUSY_TX) || (huart->State == HAL_UART_STATE_BUSY_TX_RX)) + { + + if(huart->TxXferCount == 0) + { + /* Disable the UART Transmit Data Register Empty Interrupt */ + __HAL_UART_DISABLE_IT(huart, UART_IT_TXE); + + /* Check if a receive Process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + huart->State = HAL_UART_STATE_BUSY_RX; + } + else + { + /* Disable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_UART_DISABLE_IT(huart, UART_IT_ERR); + + huart->State = HAL_UART_STATE_READY; + } + + /* Wait on TC flag to be able to start a second transfer */ + if(UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_TC, RESET, HAL_UART_TIMEOUT_VALUE) != HAL_OK) + { + return HAL_TIMEOUT; + } + + HAL_UART_TxCpltCallback(huart); + + return HAL_OK; + } + else + { + if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE)) + { + tmp = (uint16_t*) huart->pTxBuffPtr; + huart->Instance->TDR = (*tmp & (uint16_t)0x01FF); + huart->pTxBuffPtr += 2; + } + else + { + huart->Instance->TDR = (uint8_t)(*huart->pTxBuffPtr++ & (uint8_t)0xFF); + } + + huart->TxXferCount--; + + return HAL_OK; + } + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Wrap up transmission in non-blocking mode. + * @param huart: pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +static HAL_StatusTypeDef UART_EndTransmit_IT(UART_HandleTypeDef *huart) +{ + /* Disable the UART Transmit Complete Interrupt */ + __HAL_UART_DISABLE_IT(huart, UART_IT_TC); + + /* Check if a receive process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + huart->State = HAL_UART_STATE_BUSY_RX; + } + else + { + /* Disable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_UART_DISABLE_IT(huart, UART_IT_ERR); + + huart->State = HAL_UART_STATE_READY; + } + + HAL_UART_TxCpltCallback(huart); + + return HAL_OK; +} + +/** + * @brief Receive an amount of data in interrupt mode + * Function called under interruption only, once + * interruptions have been enabled by HAL_UART_Receive_IT() + * @param huart: UART handle + * @retval HAL status + */ +static HAL_StatusTypeDef UART_Receive_IT(UART_HandleTypeDef *huart) +{ + uint16_t* tmp; + uint16_t uhMask = huart->Mask; + + if((huart->State == HAL_UART_STATE_BUSY_RX) || (huart->State == HAL_UART_STATE_BUSY_TX_RX)) + { + + if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE)) + { + tmp = (uint16_t*) huart->pRxBuffPtr ; + *tmp = (uint16_t)(huart->Instance->RDR & uhMask); + huart->pRxBuffPtr +=2; + } + else + { + *huart->pRxBuffPtr++ = (uint8_t)(huart->Instance->RDR & (uint8_t)uhMask); + } + + if(--huart->RxXferCount == 0) + { + __HAL_UART_DISABLE_IT(huart, UART_IT_RXNE); + + /* Check if a transmit Process is ongoing or not */ + if(huart->State == HAL_UART_STATE_BUSY_TX_RX) + { + huart->State = HAL_UART_STATE_BUSY_TX; + } + else + { + /* Disable the UART Parity Error Interrupt */ + __HAL_UART_DISABLE_IT(huart, UART_IT_PE); + + /* Disable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_UART_DISABLE_IT(huart, UART_IT_ERR); + + huart->State = HAL_UART_STATE_READY; + } + + HAL_UART_RxCpltCallback(huart); + + return HAL_OK; + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @} + */ + +/** @defgroup UART_Exported_Functions_Group3 Peripheral Control functions + * @brief UART control functions + * +@verbatim + =============================================================================== + ##### Peripheral Control functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to control the UART. + (+) HAL_UART_GetState() API is helpful to check in run-time the state of the UART peripheral. + (+) HAL_MultiProcessor_EnableMuteMode() API enables mute mode + (+) HAL_MultiProcessor_DisableMuteMode() API disables mute mode + (+) HAL_MultiProcessor_EnterMuteMode() API enters mute mode + (+) HAL_MultiProcessor_EnableMuteMode() API enables mute mode + (+) UART_SetConfig() API configures the UART peripheral + (+) UART_AdvFeatureConfig() API optionally configures the UART advanced features + (+) UART_CheckIdleState() API ensures that TEACK and/or REACK are set after initialization + (+) HAL_HalfDuplex_EnableTransmitter() API disables receiver and enables transmitter + (+) HAL_HalfDuplex_EnableReceiver() API disables transmitter and enables receiver + (+) HAL_LIN_SendBreak() API transmits the break characters +@endverbatim + * @{ + */ + +/** + * @brief Enable UART in mute mode (doesn't mean UART enters mute mode; + * to enter mute mode, HAL_MultiProcessor_EnterMuteMode() API must be called) + * @param huart: UART handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MultiProcessor_EnableMuteMode(UART_HandleTypeDef *huart) +{ + /* Process Locked */ + __HAL_LOCK(huart); + + huart->State = HAL_UART_STATE_BUSY; + + /* Enable USART mute mode by setting the MME bit in the CR1 register */ + huart->Instance->CR1 |= USART_CR1_MME; + + huart->State = HAL_UART_STATE_READY; + + return (UART_CheckIdleState(huart)); +} + +/** + * @brief Disable UART mute mode (doesn't mean it actually wakes up the software, + * as it may not have been in mute mode at this very moment). + * @param huart: uart handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MultiProcessor_DisableMuteMode(UART_HandleTypeDef *huart) +{ + /* Process Locked */ + __HAL_LOCK(huart); + + huart->State = HAL_UART_STATE_BUSY; + + /* Disable USART mute mode by clearing the MME bit in the CR1 register */ + huart->Instance->CR1 &= ~(USART_CR1_MME); + + huart->State = HAL_UART_STATE_READY; + + return (UART_CheckIdleState(huart)); +} + +/** + * @brief Enter UART mute mode (means UART actually enters mute mode). + * To exit from mute mode, HAL_MultiProcessor_DisableMuteMode() API must be called. + * @param huart: uart handle + * @retval HAL status + */ +void HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart) +{ + __HAL_UART_SEND_REQ(huart, UART_MUTE_MODE_REQUEST); +} + + + +/** + * @brief return the UART state + * @param huart: uart handle + * @retval HAL state + */ +HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart) +{ + return huart->State; +} + +/** +* @brief Return the UART error code +* @param huart : pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART. +* @retval UART Error Code +*/ +uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart) +{ + return huart->ErrorCode; +} + +/** + * @brief Configure the UART peripheral + * @param huart: uart handle + * @retval None + */ +HAL_StatusTypeDef UART_SetConfig(UART_HandleTypeDef *huart) +{ + uint32_t tmpreg = 0x00000000; + UART_ClockSourceTypeDef clocksource = UART_CLOCKSOURCE_UNDEFINED; + uint16_t brrtemp = 0x0000; + uint16_t usartdiv = 0x0000; + HAL_StatusTypeDef ret = HAL_OK; + + /* Check the parameters */ + assert_param(IS_UART_BAUDRATE(huart->Init.BaudRate)); + assert_param(IS_UART_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_STOPBITS(huart->Init.StopBits)); + assert_param(IS_UART_PARITY(huart->Init.Parity)); + assert_param(IS_UART_MODE(huart->Init.Mode)); + assert_param(IS_UART_HARDWARE_FLOW_CONTROL(huart->Init.HwFlowCtl)); + assert_param(IS_UART_ONE_BIT_SAMPLE(huart->Init.OneBitSampling)); + + + /*-------------------------- USART CR1 Configuration -----------------------*/ + /* Clear M, PCE, PS, TE, RE and OVER8 bits and configure + * the UART Word Length, Parity, Mode and oversampling: + * set the M bits according to huart->Init.WordLength value + * set PCE and PS bits according to huart->Init.Parity value + * set TE and RE bits according to huart->Init.Mode value + * set OVER8 bit according to huart->Init.OverSampling value */ + tmpreg = (uint32_t)huart->Init.WordLength | huart->Init.Parity | huart->Init.Mode | huart->Init.OverSampling ; + MODIFY_REG(huart->Instance->CR1, UART_CR1_FIELDS, tmpreg); + + /*-------------------------- USART CR2 Configuration -----------------------*/ + /* Configure the UART Stop Bits: Set STOP[13:12] bits according + * to huart->Init.StopBits value */ + MODIFY_REG(huart->Instance->CR2, USART_CR2_STOP, huart->Init.StopBits); + + /*-------------------------- USART CR3 Configuration -----------------------*/ + /* Configure + * - UART HardWare Flow Control: set CTSE and RTSE bits according + * to huart->Init.HwFlowCtl value + * - one-bit sampling method versus three samples' majority rule according + * to huart->Init.OneBitSampling */ + tmpreg = (uint32_t)huart->Init.HwFlowCtl | huart->Init.OneBitSampling ; + MODIFY_REG(huart->Instance->CR3, (USART_CR3_RTSE | USART_CR3_CTSE | USART_CR3_ONEBIT), tmpreg); + + /*-------------------------- USART BRR Configuration -----------------------*/ + UART_GETCLOCKSOURCE(huart, clocksource); + + /* Check UART Over Sampling to set Baud Rate Register */ + if (huart->Init.OverSampling == UART_OVERSAMPLING_8) + { + switch (clocksource) + { + case UART_CLOCKSOURCE_PCLK1: + usartdiv = (uint16_t)(UART_DIV_SAMPLING8(HAL_RCC_GetPCLK1Freq(), huart->Init.BaudRate)); + break; + case UART_CLOCKSOURCE_PCLK2: + usartdiv = (uint16_t)(UART_DIV_SAMPLING8(HAL_RCC_GetPCLK2Freq(), huart->Init.BaudRate)); + break; + case UART_CLOCKSOURCE_HSI: + usartdiv = (uint16_t)(UART_DIV_SAMPLING8(HSI_VALUE, huart->Init.BaudRate)); + break; + case UART_CLOCKSOURCE_SYSCLK: + usartdiv = (uint16_t)(UART_DIV_SAMPLING8(HAL_RCC_GetSysClockFreq(), huart->Init.BaudRate)); + break; + case UART_CLOCKSOURCE_LSE: + usartdiv = (uint16_t)(UART_DIV_SAMPLING8(LSE_VALUE, huart->Init.BaudRate)); + break; + case UART_CLOCKSOURCE_UNDEFINED: + default: + ret = HAL_ERROR; + break; + } + + brrtemp = usartdiv & 0xFFF0; + brrtemp |= (uint16_t)((usartdiv & (uint16_t)0x000F) >> 1U); + huart->Instance->BRR = brrtemp; + } + else + { + switch (clocksource) + { + case UART_CLOCKSOURCE_PCLK1: + huart->Instance->BRR = (uint16_t)(UART_DIV_SAMPLING16(HAL_RCC_GetPCLK1Freq(), huart->Init.BaudRate)); + break; + case UART_CLOCKSOURCE_PCLK2: + huart->Instance->BRR = (uint16_t)(UART_DIV_SAMPLING16(HAL_RCC_GetPCLK2Freq(), huart->Init.BaudRate)); + break; + case UART_CLOCKSOURCE_HSI: + huart->Instance->BRR = (uint16_t)(UART_DIV_SAMPLING16(HSI_VALUE, huart->Init.BaudRate)); + break; + case UART_CLOCKSOURCE_SYSCLK: + huart->Instance->BRR = (uint16_t)(UART_DIV_SAMPLING16(HAL_RCC_GetSysClockFreq(), huart->Init.BaudRate)); + break; + case UART_CLOCKSOURCE_LSE: + huart->Instance->BRR = (uint16_t)(UART_DIV_SAMPLING16(LSE_VALUE, huart->Init.BaudRate)); + break; + case UART_CLOCKSOURCE_UNDEFINED: + default: + ret = HAL_ERROR; + break; + } + } + + return ret; + +} + + +/** + * @brief Configure the UART peripheral advanced features + * @param huart: uart handle + * @retval None + */ +void UART_AdvFeatureConfig(UART_HandleTypeDef *huart) +{ + /* Check whether the set of advanced features to configure is properly set */ + assert_param(IS_UART_ADVFEATURE_INIT(huart->AdvancedInit.AdvFeatureInit)); + + /* if required, configure TX pin active level inversion */ + if(HAL_IS_BIT_SET(huart->AdvancedInit.AdvFeatureInit, UART_ADVFEATURE_TXINVERT_INIT)) + { + assert_param(IS_UART_ADVFEATURE_TXINV(huart->AdvancedInit.TxPinLevelInvert)); + MODIFY_REG(huart->Instance->CR2, USART_CR2_TXINV, huart->AdvancedInit.TxPinLevelInvert); + } + + /* if required, configure RX pin active level inversion */ + if(HAL_IS_BIT_SET(huart->AdvancedInit.AdvFeatureInit, UART_ADVFEATURE_RXINVERT_INIT)) + { + assert_param(IS_UART_ADVFEATURE_RXINV(huart->AdvancedInit.RxPinLevelInvert)); + MODIFY_REG(huart->Instance->CR2, USART_CR2_RXINV, huart->AdvancedInit.RxPinLevelInvert); + } + + /* if required, configure data inversion */ + if(HAL_IS_BIT_SET(huart->AdvancedInit.AdvFeatureInit, UART_ADVFEATURE_DATAINVERT_INIT)) + { + assert_param(IS_UART_ADVFEATURE_DATAINV(huart->AdvancedInit.DataInvert)); + MODIFY_REG(huart->Instance->CR2, USART_CR2_DATAINV, huart->AdvancedInit.DataInvert); + } + + /* if required, configure RX/TX pins swap */ + if(HAL_IS_BIT_SET(huart->AdvancedInit.AdvFeatureInit, UART_ADVFEATURE_SWAP_INIT)) + { + assert_param(IS_UART_ADVFEATURE_SWAP(huart->AdvancedInit.Swap)); + MODIFY_REG(huart->Instance->CR2, USART_CR2_SWAP, huart->AdvancedInit.Swap); + } + + /* if required, configure RX overrun detection disabling */ + if(HAL_IS_BIT_SET(huart->AdvancedInit.AdvFeatureInit, UART_ADVFEATURE_RXOVERRUNDISABLE_INIT)) + { + assert_param(IS_UART_OVERRUN(huart->AdvancedInit.OverrunDisable)); + MODIFY_REG(huart->Instance->CR3, USART_CR3_OVRDIS, huart->AdvancedInit.OverrunDisable); + } + + /* if required, configure DMA disabling on reception error */ + if(HAL_IS_BIT_SET(huart->AdvancedInit.AdvFeatureInit, UART_ADVFEATURE_DMADISABLEONERROR_INIT)) + { + assert_param(IS_UART_ADVFEATURE_DMAONRXERROR(huart->AdvancedInit.DMADisableonRxError)); + MODIFY_REG(huart->Instance->CR3, USART_CR3_DDRE, huart->AdvancedInit.DMADisableonRxError); + } + + /* if required, configure auto Baud rate detection scheme */ + if(HAL_IS_BIT_SET(huart->AdvancedInit.AdvFeatureInit, UART_ADVFEATURE_AUTOBAUDRATE_INIT)) + { + assert_param(IS_UART_ADVFEATURE_AUTOBAUDRATE(huart->AdvancedInit.AutoBaudRateEnable)); + MODIFY_REG(huart->Instance->CR2, USART_CR2_ABREN, huart->AdvancedInit.AutoBaudRateEnable); + /* set auto Baudrate detection parameters if detection is enabled */ + if(huart->AdvancedInit.AutoBaudRateEnable == UART_ADVFEATURE_AUTOBAUDRATE_ENABLE) + { + assert_param(IS_UART_ADVFEATURE_AUTOBAUDRATEMODE(huart->AdvancedInit.AutoBaudRateMode)); + MODIFY_REG(huart->Instance->CR2, USART_CR2_ABRMODE, huart->AdvancedInit.AutoBaudRateMode); + } + } + + /* if required, configure MSB first on communication line */ + if(HAL_IS_BIT_SET(huart->AdvancedInit.AdvFeatureInit, UART_ADVFEATURE_MSBFIRST_INIT)) + { + assert_param(IS_UART_ADVFEATURE_MSBFIRST(huart->AdvancedInit.MSBFirst)); + MODIFY_REG(huart->Instance->CR2, USART_CR2_MSBFIRST, huart->AdvancedInit.MSBFirst); + } +} + + + +/** + * @brief Check the UART Idle State + * @param huart: uart handle + * @retval HAL status + */ +HAL_StatusTypeDef UART_CheckIdleState(UART_HandleTypeDef *huart) +{ + /* Initialize the UART ErrorCode */ + huart->ErrorCode = HAL_UART_ERROR_NONE; + + /* Check if the Transmitter is enabled */ + if((huart->Instance->CR1 & USART_CR1_TE) == USART_CR1_TE) + { + /* Wait until TEACK flag is set */ + if(UART_WaitOnFlagUntilTimeout(huart, USART_ISR_TEACK, RESET, HAL_UART_TIMEOUT_VALUE) != HAL_OK) + { + /* Timeout Occurred */ + return HAL_TIMEOUT; + } + } + /* Check if the Receiver is enabled */ + if((huart->Instance->CR1 & USART_CR1_RE) == USART_CR1_RE) + { + /* Wait until REACK flag is set */ + if(UART_WaitOnFlagUntilTimeout(huart, USART_ISR_REACK, RESET, HAL_UART_TIMEOUT_VALUE) != HAL_OK) + { + /* Timeout Occurred */ + return HAL_TIMEOUT; + } + } + + /* Initialize the UART State */ + huart->State= HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Enables the UART transmitter and disables the UART receiver. + * @param huart: UART handle + * @retval HAL status + * @retval None + */ +HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart) +{ + /* Process Locked */ + __HAL_LOCK(huart); + huart->State = HAL_UART_STATE_BUSY; + + /* Clear TE and RE bits */ + CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TE | USART_CR1_RE)); + /* Enable the USART's transmit interface by setting the TE bit in the USART CR1 register */ + SET_BIT(huart->Instance->CR1, USART_CR1_TE); + + huart->State= HAL_UART_STATE_READY; + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Enables the UART receiver and disables the UART transmitter. + * @param huart: UART handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart) +{ + /* Process Locked */ + __HAL_LOCK(huart); + huart->State = HAL_UART_STATE_BUSY; + + /* Clear TE and RE bits */ + CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TE | USART_CR1_RE)); + /* Enable the USART's receive interface by setting the RE bit in the USART CR1 register */ + SET_BIT(huart->Instance->CR1, USART_CR1_RE); + + huart->State = HAL_UART_STATE_READY; + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + + +/** + * @brief Transmits break characters. + * @param huart: UART handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart) +{ + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->State = HAL_UART_STATE_BUSY; + + /* Send break characters */ + huart->Instance->RQR |= UART_SENDBREAK_REQUEST; + + huart->State = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_UART_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/