File content as of revision 0:e3161ef4ffd9:

#include "mbed.h"
/*
 * HAL_TIM_Encoder_MspInit()
 * Overrides the __weak function stub in stm32l4xx_hal_tim.h
 *
 * Edit the below for your preferred pin wiring & pullup/down
 * I have encoder common at 3V3, using GPIO_PULLDOWN on inputs.
 * Encoder A&B outputs connected directly to GPIOs.
 *
 * http://www.st.com/st-web-ui/static/active/en/resource/technical/document/datasheet/DM00098321.pdf
 * Table 9 has GPIO alternate function pinout mappings.
 *
 * TIM2_CH1: AF1 @ PA_0, PA_5, PA_15, PE_9
 * TIM2_CH2: AF1 @ PA_1, PB_3, PE_10
 *
 * TIM3_CH1: AF2 @ PA_6, PB_4, PC_6, PE_3
 * TIM3_CH2: AF2 @ PA_7, PB_5, PC_7, PE_4
 *
 * TIM4_CH1: AF2 @ PB_6, PD_12
 * TIM4_CH2: AF2 @ PB_7, PD_13
 *
 * TIM5_CH1: AF2 @ PA_0*    *TIM5 used by mbed system ticker so unavailable
 * TIM5_CH2: AF2 @ PA_1*
 *
 */
 
#ifdef TARGET_STM32L1
void HAL_TIM_Encoder_MspInit(TIM_HandleTypeDef *htim)
{
    GPIO_InitTypeDef GPIO_InitStruct;
 
    if (htim->Instance == TIM2) { //PA0 PA1 = Nucleo A0 A1
        __TIM2_CLK_ENABLE();
        __GPIOA_CLK_ENABLE();
        GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1;
        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
        GPIO_InitStruct.Pull =  GPIO_NOPULL;
        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
        GPIO_InitStruct.Alternate = GPIO_AF1_TIM2;
        HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
    }
//    else if (htim->Instance == TIM3) { //PB4 PB5 = Nucleo D5 D4
//        __TIM3_CLK_ENABLE();
//        __GPIOB_CLK_ENABLE();
//        GPIO_InitStruct.Pin = GPIO_PIN_4 | GPIO_PIN_5;
//        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
//        GPIO_InitStruct.Pull = GPIO_PULLDOWN;
//        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
//        GPIO_InitStruct.Alternate = GPIO_AF2_TIM3;
//        HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
//    }
//    else if (htim->Instance == TIM4) { // PB6 PB7 = Nucleo D10 MORPHO_PB7
//        __TIM4_CLK_ENABLE();
//        __GPIOB_CLK_ENABLE();
//        GPIO_InitStruct.Pin = GPIO_PIN_6 | GPIO_PIN_7;
//        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
//        GPIO_InitStruct.Pull = GPIO_PULLDOWN;
//        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
//        GPIO_InitStruct.Alternate = GPIO_AF2_TIM4;
//        HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
//    }
}
#endif