Hal Drivers for L4
Dependents: BSP OneHopeOnePrayer FINAL_AUDIO_RECORD AudioDemo
Fork of STM32L4xx_HAL_Driver by
Diff: Src/stm32l4xx_hal_pwr.c
- Revision:
- 0:80ee8f3b695e
diff -r 000000000000 -r 80ee8f3b695e Src/stm32l4xx_hal_pwr.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/Src/stm32l4xx_hal_pwr.c Mon Nov 02 19:37:23 2015 +0000 @@ -0,0 +1,667 @@ +/** + ****************************************************************************** + * @file stm32l4xx_hal_pwr.c + * @author MCD Application Team + * @version V1.1.0 + * @date 16-September-2015 + * @brief PWR HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Power Controller (PWR) peripheral: + * + Initialization/de-initialization functions + * + Peripheral Control functions + * + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32l4xx_hal.h" + +/** @addtogroup STM32L4xx_HAL_Driver + * @{ + */ + +/** @defgroup PWR PWR + * @brief PWR HAL module driver + * @{ + */ + +#ifdef HAL_PWR_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ + +/** @defgroup PWR_Private_Defines PWR Private Defines + * @{ + */ + +/** @defgroup PWR_PVD_Mode_Mask PWR PVD Mode Mask + * @{ + */ +#define PVD_MODE_IT ((uint32_t)0x00010000) /*!< Mask for interruption yielded by PVD threshold crossing */ +#define PVD_MODE_EVT ((uint32_t)0x00020000) /*!< Mask for event yielded by PVD threshold crossing */ +#define PVD_RISING_EDGE ((uint32_t)0x00000001) /*!< Mask for rising edge set as PVD trigger */ +#define PVD_FALLING_EDGE ((uint32_t)0x00000002) /*!< Mask for falling edge set as PVD trigger */ +/** + * @} + */ + +/** + * @} + */ + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Exported functions --------------------------------------------------------*/ + +/** @defgroup PWR_Exported_Functions PWR Exported Functions + * @{ + */ + +/** @defgroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and de-initialization functions + * +@verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] + +@endverbatim + * @{ + */ + +/** + * @brief Deinitialize the HAL PWR peripheral registers to their default reset values. + * @retval None + */ +void HAL_PWR_DeInit(void) +{ + __HAL_RCC_PWR_FORCE_RESET(); + __HAL_RCC_PWR_RELEASE_RESET(); +} + +/** + * @brief Enable access to the backup domain + * (RTC registers, RTC backup data registers). + * @note After reset, the backup domain is protected against + * possible unwanted write accesses. + * @note RTCSEL that sets the RTC clock source selection is in the RTC back-up domain. + * In order to set or modify the RTC clock, the backup domain access must be + * disabled. + * @note LSEON bit that switches on and off the LSE crystal belongs as well to the + * back-up domain. + * @retval None + */ +void HAL_PWR_EnableBkUpAccess(void) +{ + SET_BIT(PWR->CR1, PWR_CR1_DBP); +} + +/** + * @brief Disable access to the backup domain + * (RTC registers, RTC backup data registers). + * @retval None + */ +void HAL_PWR_DisableBkUpAccess(void) +{ + CLEAR_BIT(PWR->CR1, PWR_CR1_DBP); +} + + + + +/** + * @} + */ + + + +/** @defgroup PWR_Exported_Functions_Group2 Peripheral Control functions + * @brief Low Power modes configuration functions + * +@verbatim + + =============================================================================== + ##### Peripheral Control functions ##### + =============================================================================== + + [..] + *** PVD configuration *** + ========================= + [..] + (+) The PVD is used to monitor the VDD power supply by comparing it to a + threshold selected by the PVD Level (PLS[2:0] bits in PWR_CR2 register). + + (+) PVDO flag is available to indicate if VDD/VDDA is higher or lower + than the PVD threshold. This event is internally connected to the EXTI + line16 and can generate an interrupt if enabled. This is done through + __HAL_PVD_EXTI_ENABLE_IT() macro. + (+) The PVD is stopped in Standby mode. + + + *** WakeUp pin configuration *** + ================================ + [..] + (+) WakeUp pins are used to wakeup the system from Standby mode or Shutdown mode. + The polarity of these pins can be set to configure event detection on high + level (rising edge) or low level (falling edge). + + + + *** Low Power modes configuration *** + ===================================== + [..] + The devices feature 8 low-power modes: + (+) Low-power Run mode: core and peripherals are running, regulator in low power mode. + (+) Sleep mode: Cortex-M4 core stopped, peripherals kept running, regulator in normal mode. + (+) Low-power Sleep mode: Cortex-M4 core stopped, peripherals kept running, regulator in low power mode. + (+) Stop 1 mode: all clocks are stopped except LSI and LSE, regulator in normal or low power mode. + (+) Stop 2 mode: all clocks are stopped except LSI and LSE, regulator in low power mode, reduced set of waking up IPs compared to Stop 1 mode. + (+) Standby mode with SRAM2: all clocks are stopped except LSI and LSE, SRAM2 content preserved, regulator in low power mode. + (+) Standby mode without SRAM2: all clocks are stopped except LSI and LSE, regulator off. + (+) Shutdown mode: all clocks are stopped except LSE, regulator off. + + + *** Low-power run mode *** + ========================== + [..] + (+) Entry: (from main run mode) + (++) set LPR bit with HAL_PWREx_EnableLowPowerRunMode() API after having decreased the system clock below 2 MHz. + + (+) Exit: + (++) clear LPR bit then wait for REGLP bit to be reset with HAL_PWREx_DisableLowPowerRunMode() API. Only + then can the system clock frequency be increased above 2 MHz. + + + *** Sleep mode / Low-power sleep mode *** + ========================================= + [..] + (+) Entry: + The Sleep mode / Low-power Sleep mode is entered thru HAL_PWR_EnterSLEEPMode() API + in specifying whether or not the regulator is forced to low-power mode and if exit is interrupt or event-triggered. + (++) PWR_MAINREGULATOR_ON: Sleep mode (regulator in main mode). + (++) PWR_LOWPOWERREGULATOR_ON: Low-power sleep (regulator in low power mode). + In the latter case, the system clock frequency must have been decreased below 2 MHz beforehand. + (++) PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction + (++) PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction + + (+) WFI Exit: + (++) Any peripheral interrupt acknowledged by the nested vectored interrupt + controller (NVIC) or any wake-up event. + + (+) WFE Exit: + (++) Any wake-up event such as an EXTI line configured in event mode. + + [..] When exiting the Low-power sleep mode by issuing an interrupt or a wakeup event, + the MCU is in Low-power Run mode. + + *** Stop 1 and Stop 2 modes *** + =============================== + [..] + (+) Entry: + The Stop 1 or Stop 2 modes are entered thru the following API's: + (++) HAL_PWR_EnterSTOPMode() [for legacy porting reasons] or HAL_PWREx_EnterSTOP1Mode() for mode 1 + (++) HAL_PWREx_EnterSTOP2Mode for mode 2. + (+) Regulator setting (applicable to Stop 1 mode only): + (++) PWR_MAINREGULATOR_ON + (++) PWR_LOWPOWERREGULATOR_ON + (+) Exit (interrupt or event-triggered, specified when entering STOP mode): + (++) PWR_STOPENTRY_WFI: enter Stop mode with WFI instruction + (++) PWR_STOPENTRY_WFE: enter Stop mode with WFE instruction + + (+) WFI Exit: + (++) Any EXTI Line (Internal or External) configured in Interrupt mode. + (++) Some specific communication peripherals (USART, LPUART, I2C) interrupts + when programmed in wakeup mode. + (+) WFE Exit: + (++) Any EXTI Line (Internal or External) configured in Event mode. + + [..] + When exiting Stop 1 mode, the MCU is either in Run mode or in Low-power Run mode + depending on the LPR bit setting. + When exiting Stop 2 mode, the MCU is in Run mode. + + *** Standby mode *** + ==================== + [..] + The Standby mode offers two options: + (+) option a) all clocks off except LSI and LSE, RRS bit set (keeps voltage regulator in low power mode). + SRAM and registers contents are lost except for the SRAM2 content, the RTC registers, RTC backup registers + and Standby circuitry. + (+) option b) all clocks off except LSI and LSE, RRS bit cleared (voltage regulator then disabled). + SRAM and register contents are lost except for the RTC registers, RTC backup registers + and Standby circuitry. + + (++) Entry: + (+++) The Standby mode is entered thru HAL_PWR_EnterSTANDBYMode() API. + SRAM1 and register contents are lost except for registers in the Backup domain and + Standby circuitry. SRAM2 content can be preserved if the bit RRS is set in PWR_CR3 register. + To enable this feature, the user can resort to HAL_PWREx_EnableSRAM2ContentRetention() API + to set RRS bit. + + (++) Exit: + (+++) WKUP pin rising edge, RTC alarm or wakeup, tamper event, time-stamp event, + external reset in NRST pin, IWDG reset. + + [..] After waking up from Standby mode, program execution restarts in the same way as after a Reset. + + + *** Shutdown mode *** + ====================== + [..] + In Shutdown mode, + voltage regulator is disabled, all clocks are off except LSE, RRS bit is cleared. + SRAM and registers contents are lost except for backup domain registers. + + (+) Entry: + The Shutdown mode is entered thru HAL_PWREx_EnterSHUTDOWNMode() API. + + (+) Exit: + (++) WKUP pin rising edge, RTC alarm or wakeup, tamper event, time-stamp event, + external reset in NRST pin. + + [..] After waking up from Shutdown mode, program execution restarts in the same way as after a Reset. + + + *** Auto-wakeup (AWU) from low-power mode *** + ============================================= + [..] + The MCU can be woken up from low-power mode by an RTC Alarm event, an RTC + Wakeup event, a tamper event or a time-stamp event, without depending on + an external interrupt (Auto-wakeup mode). + + (+) RTC auto-wakeup (AWU) from the Stop, Standby and Shutdown modes + + + (++) To wake up from the Stop mode with an RTC alarm event, it is necessary to + configure the RTC to generate the RTC alarm using the HAL_RTC_SetAlarm_IT() function. + + (++) To wake up from the Stop mode with an RTC Tamper or time stamp event, it + is necessary to configure the RTC to detect the tamper or time stamp event using the + HAL_RTCEx_SetTimeStamp_IT() or HAL_RTCEx_SetTamper_IT() functions. + + (++) To wake up from the Stop mode with an RTC WakeUp event, it is necessary to + configure the RTC to generate the RTC WakeUp event using the HAL_RTCEx_SetWakeUpTimer_IT() function. + +@endverbatim + * @{ + */ + + + +/** + * @brief Configure the voltage threshold detected by the Power Voltage Detector (PVD). + * @param sConfigPVD: pointer to a PWR_PVDTypeDef structure that contains the PVD + * configuration information. + * @note Refer to the electrical characteristics of your device datasheet for + * more details about the voltage thresholds corresponding to each + * detection level. + * @retval None + */ +HAL_StatusTypeDef HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD) +{ + /* Check the parameters */ + assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel)); + assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode)); + + /* Set PLS bits according to PVDLevel value */ + MODIFY_REG(PWR->CR2, PWR_CR2_PLS, sConfigPVD->PVDLevel); + + /* Clear any previous config. Keep it clear if no event or IT mode is selected */ + __HAL_PWR_PVD_EXTI_DISABLE_EVENT(); + __HAL_PWR_PVD_EXTI_DISABLE_IT(); + __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); + __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE(); + + /* Configure interrupt mode */ + if((sConfigPVD->Mode & PVD_MODE_IT) == PVD_MODE_IT) + { + __HAL_PWR_PVD_EXTI_ENABLE_IT(); + } + + /* Configure event mode */ + if((sConfigPVD->Mode & PVD_MODE_EVT) == PVD_MODE_EVT) + { + __HAL_PWR_PVD_EXTI_ENABLE_EVENT(); + } + + /* Configure the edge */ + if((sConfigPVD->Mode & PVD_RISING_EDGE) == PVD_RISING_EDGE) + { + __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE(); + } + + if((sConfigPVD->Mode & PVD_FALLING_EDGE) == PVD_FALLING_EDGE) + { + __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE(); + } + + return HAL_OK; +} + + +/** + * @brief Enable the Power Voltage Detector (PVD). + * @retval None + */ +void HAL_PWR_EnablePVD(void) +{ + SET_BIT(PWR->CR2, PWR_CR2_PVDE); +} + +/** + * @brief Disable the Power Voltage Detector (PVD). + * @retval None + */ +void HAL_PWR_DisablePVD(void) +{ + CLEAR_BIT(PWR->CR2, PWR_CR2_PVDE); +} + + + + +/** + * @brief Enable the WakeUp PINx functionality. + * @param WakeUpPinPolarity: Specifies which Wake-Up pin to enable. + * This parameter can be one of the following legacy values which set the default polarity + * i.e. detection on high level (rising edge): + * @arg PWR_WAKEUP_PIN1, PWR_WAKEUP_PIN2, PWR_WAKEUP_PIN3, PWR_WAKEUP_PIN4, PWR_WAKEUP_PIN5 + * + * or one of the following value where the user can explicitly specify the enabled pin and + * the chosen polarity: + * @arg PWR_WAKEUP_PIN1_HIGH or PWR_WAKEUP_PIN1_LOW + * @arg PWR_WAKEUP_PIN2_HIGH or PWR_WAKEUP_PIN2_LOW + * @arg PWR_WAKEUP_PIN3_HIGH or PWR_WAKEUP_PIN3_LOW + * @arg PWR_WAKEUP_PIN4_HIGH or PWR_WAKEUP_PIN4_LOW + * @arg PWR_WAKEUP_PIN5_HIGH or PWR_WAKEUP_PIN5_LOW + * @note PWR_WAKEUP_PINx and PWR_WAKEUP_PINx_HIGH are equivalent. + * @retval None + */ +void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinPolarity) +{ + assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinPolarity)); + + /* Specifies the Wake-Up pin polarity for the event detection + (rising or falling edge) */ + MODIFY_REG(PWR->CR4, (PWR_CR3_EWUP & WakeUpPinPolarity), (WakeUpPinPolarity >> PWR_WUP_POLARITY_SHIFT)); + + /* Enable wake-up pin */ + SET_BIT(PWR->CR3, (PWR_CR3_EWUP & WakeUpPinPolarity)); + + +} + +/** + * @brief Disable the WakeUp PINx functionality. + * @param WakeUpPinx: Specifies the Power Wake-Up pin to disable. + * This parameter can be one of the following values: + * @arg PWR_WAKEUP_PIN1, PWR_WAKEUP_PIN2, PWR_WAKEUP_PIN3, PWR_WAKEUP_PIN4, PWR_WAKEUP_PIN5 + * @retval None + */ +void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx) +{ + assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinx)); + + CLEAR_BIT(PWR->CR3, WakeUpPinx); +} + + +/** + * @brief Enter Sleep or Low-power Sleep mode. + * @note In Sleep/Low-power Sleep mode, all I/O pins keep the same state as in Run mode. + * @param Regulator: Specifies the regulator state in Sleep/Low-power Sleep mode. + * This parameter can be one of the following values: + * @arg PWR_MAINREGULATOR_ON: Sleep mode (regulator in main mode) + * @arg PWR_LOWPOWERREGULATOR_ON: Low-power Sleep mode (regulator in low-power mode) + * @note Low-power Sleep mode is entered from Low-power Run mode. Therefore, if not yet + * in Low-power Run mode before calling HAL_PWR_EnterSLEEPMode() with Regulator set + * to PWR_LOWPOWERREGULATOR_ON, the user can optionally configure the + * Flash in power-down monde in setting the SLEEP_PD bit in FLASH_ACR register. + * Additionally, the clock frequency must be reduced below 2 MHz. + * Setting SLEEP_PD in FLASH_ACR then appropriately reducing the clock frequency must + * be done before calling HAL_PWR_EnterSLEEPMode() API. + * @note When exiting Low-power Sleep mode, the MCU is in Low-power Run mode. To move in + * Run mode, the user must resort to HAL_PWREx_DisableLowPowerRunMode() API. + * @param SLEEPEntry: Specifies if Sleep mode is entered with WFI or WFE instruction. + * This parameter can be one of the following values: + * @arg PWR_SLEEPENTRY_WFI: enter Sleep or Low-power Sleep mode with WFI instruction + * @arg PWR_SLEEPENTRY_WFE: enter Sleep or Low-power Sleep mode with WFE instruction + * @note When WFI entry is used, tick interrupt have to be disabled if not desired as + * the interrupt wake up source. + * @retval None + */ +void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry) +{ + /* Check the parameters */ + assert_param(IS_PWR_REGULATOR(Regulator)); + assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry)); + + /* Set Regulator parameter */ + if (Regulator == PWR_MAINREGULATOR_ON) + { + /* If in low-power run mode at this point, exit it */ + if (HAL_IS_BIT_SET(PWR->SR2, PWR_SR2_REGLPF)) + { + HAL_PWREx_DisableLowPowerRunMode(); + } + /* Regulator now in main mode. */ + } + else + { + /* If in run mode, first move to low-power run mode. + The system clock frequency must be below 2 MHz at this point. */ + if (HAL_IS_BIT_SET(PWR->SR2, PWR_SR2_REGLPF) == RESET) + { + HAL_PWREx_EnableLowPowerRunMode(); + } + } + + /* Clear SLEEPDEEP bit of Cortex System Control Register */ + CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk)); + + /* Select SLEEP mode entry -------------------------------------------------*/ + if(SLEEPEntry == PWR_SLEEPENTRY_WFI) + { + /* Request Wait For Interrupt */ + __WFI(); + } + else + { + /* Request Wait For Event */ + __SEV(); + __WFE(); + __WFE(); + } + +} + + +/** + * @brief Enter Stop 1 mode + * @note This API is named HAL_PWR_EnterSTOPMode to ensure compatibility with legacy code running + * on devices where only "Stop mode" is mentioned. On STM32L4, Stop 1 mode and Stop modes + * are equivalent. + * @note In Stop 1 mode, all I/O pins keep the same state as in Run mode. + * @note All clocks in the VCORE domain are stopped; the PLL, the MSI, + * the HSI and the HSE oscillators are disabled. Some peripherals with the wakeup capability + * (I2Cx, USARTx and LPUART) can switch on the HSI to receive a frame, and switch off the HSI + * after receiving the frame if it is not a wakeup frame. In this case, the HSI clock is propagated + * only to the peripheral requesting it. + * SRAM1, SRAM2 and register contents are preserved. + * The BOR is available. + * The voltage regulator can be configured either in normal or low-power mode. + * @note When exiting Stop 1 mode by issuing an interrupt or a wakeup event, + * the HSI RC oscillator is selected as system clock if STOPWUCK bit in RCC_CFGR register + * is set; the MSI oscillator is selected if STOPWUCK is cleared. + * @note When the voltage regulator operates in low power mode, an additional + * startup delay is incurred when waking up from Stop 1 mode. + * By keeping the internal regulator ON during Stop 1 mode, the consumption + * is higher although the startup time is reduced. + * @param Regulator: Specifies the regulator state in Stop 1 mode. + * This parameter can be one of the following values: + * @arg PWR_MAINREGULATOR_ON: Stop 1 mode with regulator ON + * @arg PWR_LOWPOWERREGULATOR_ON: Stop 1 mode with low power regulator ON + * @param STOPEntry: Specifies if Stop 1 mode in entered with WFI or WFE instruction. + * This parameter can be one of the following values: + * @arg PWR_STOPENTRY_WFI:Enter Stop 1 mode with WFI instruction + * @arg PWR_STOPENTRY_WFE: Enter Stop 1 mode with WFE instruction + * @retval None + */ +void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry) +{ + HAL_PWREx_EnterSTOP1Mode(Regulator, STOPEntry); +} + +/** + * @brief Enter Standby mode. + * @note In Standby mode, the PLL, the HSI, the MSI and the HSE oscillators are switched + * off. The voltage regulator is disabled, except when SRAM2 content is preserved + * in which case the regulator is in low-power mode. + * SRAM1 and register contents are lost except for registers in the Backup domain and + * Standby circuitry. SRAM2 content can be preserved if the bit RRS is set in PWR_CR3 register. + * To enable this feature, the user can resort to HAL_PWREx_EnableSRAM2ContentRetention() API + * to set RRS bit. + * The BOR is available. + * @note The I/Os can be configured either with a pull-up or pull-down or can be kept in analog state. + * HAL_PWREx_EnableGPIOPullUp() and HAL_PWREx_EnableGPIOPullDown() respectively enable Pull Up and + * Pull Down state, HAL_PWREx_DisableGPIOPullUp() and HAL_PWREx_DisableGPIOPullDown() disable the + * same. + * These states are effective in Standby mode only if APC bit is set through + * HAL_PWREx_EnablePullUpPullDownConfig() API. + * @retval None + */ +void HAL_PWR_EnterSTANDBYMode(void) +{ + /* Set Stand-by mode */ + MODIFY_REG(PWR->CR1, PWR_CR1_LPMS, PWR_CR1_LPMS_STANDBY); + + /* Set SLEEPDEEP bit of Cortex System Control Register */ + SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk)); + +/* This option is used to ensure that store operations are completed */ +#if defined ( __CC_ARM) + __force_stores(); +#endif + /* Request Wait For Interrupt */ + __WFI(); +} + + + +/** + * @brief Indicate Sleep-On-Exit when returning from Handler mode to Thread mode. + * @note Set SLEEPONEXIT bit of SCR register. When this bit is set, the processor + * re-enters SLEEP mode when an interruption handling is over. + * Setting this bit is useful when the processor is expected to run only on + * interruptions handling. + * @retval None + */ +void HAL_PWR_EnableSleepOnExit(void) +{ + /* Set SLEEPONEXIT bit of Cortex System Control Register */ + SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk)); +} + + +/** + * @brief Disable Sleep-On-Exit feature when returning from Handler mode to Thread mode. + * @note Clear SLEEPONEXIT bit of SCR register. When this bit is set, the processor + * re-enters SLEEP mode when an interruption handling is over. + * @retval None + */ +void HAL_PWR_DisableSleepOnExit(void) +{ + /* Clear SLEEPONEXIT bit of Cortex System Control Register */ + CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk)); +} + + + +/** + * @brief Enable CORTEX M4 SEVONPEND bit. + * @note Set SEVONPEND bit of SCR register. When this bit is set, this causes + * WFE to wake up when an interrupt moves from inactive to pended. + * @retval None + */ +void HAL_PWR_EnableSEVOnPend(void) +{ + /* Set SEVONPEND bit of Cortex System Control Register */ + SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk)); +} + + +/** + * @brief Disable CORTEX M4 SEVONPEND bit. + * @note Clear SEVONPEND bit of SCR register. When this bit is set, this causes + * WFE to wake up when an interrupt moves from inactive to pended. + * @retval None + */ +void HAL_PWR_DisableSEVOnPend(void) +{ + /* Clear SEVONPEND bit of Cortex System Control Register */ + CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk)); +} + + + + + +/** + * @brief PWR PVD interrupt callback + * @retval None + */ +__weak void HAL_PWR_PVDCallback(void) +{ + /* NOTE : This function should not be modified; when the callback is needed, + the HAL_PWR_PVDCallback can be implemented in the user file + */ +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_PWR_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ +